Several BSOD with error different ntoskrnl.exe + 75c00 involving most of the messages

Similar Questions

• Windows Vista SP2, random BSOD with error checking code 0 x 19

  Hi all

  I have seemingly random crashes on my old laptop 3 years recently - BSOD with error checking code 0 x 0000019 (0x00000020, 0xe92f4780, 0xe92f48d0, 0x0a2a0440), and BlueScreenView says that accidents are caused by ntkrnlpa.exe and Ntfs.sys. I have absolutely no idea why it happened--unusual does update, none of the material changes & software installations. The system hangs especially after maybe one or two days after starting with some sleep & wake ups inbetween and the only accidents while there are prominent running shows - namely, all the accidents that happened while I was running Firefox. Seconds before the BSoD (shell & all) system simply freezes and does not respond to ctrl + alt + delete, but is still running (as indicated by the fact that once, I forced a power off and after that restart the event log indicates the previous stop at was not planned), then watch the usual BSoD screen.

  After doing some googling, I began to suspect that this should be a memory or a hard drive problem, or maybe an overheating causing the two since he not there no significant change of software on my computer recently again issues just appeared without reason. So I cleaned my laptop fan and the heatsink and ensured that the hot air can leave the chassis without being blocked, did some checking of memory with memory auditing Windows - no problems in 5 innings and ran chkdsk on my system partition with all available options - perfectly normal, but the chkdsk has acted quite strangely that check all took about 30 seconds and no normal as the ID information of partition, size etc. that should be there never appeared; is this a normal behavior? or something is wrong with my chkdsk?

  I'm still (lol) impatiently waiting for the next crash, not sure whether the problem is still there or not. Meanwhile could you please help me understand what is the problem with my system?

  It seems that the disc is the most likely cause. If it is intermittent, it may be difficult to diagnose.

  The manufacturer of the laptop provides any diagnosis?  Several manufacturers have a key at startup to access the diagnostics.

  CHKDSK should last several minutes. There is information about the different ways to run chkdsk here:

  http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html

  You can try this disc test program:

  http://www.Seagate.com/www/en-us/support/downloads/SeaTools/

  If the version of WIndows does not find anything. Try to use the version BACK from a CD.

• BSOD on shutdown associated ntoskrnl.exe

  Hello, today I got the BSOD when stop twice. I used the blue screen and it showed that this problem related to ntoskrnl.exe. I here enclose the direction in the dump file. Please help me solve this problem. https://onedrive.live.com/redir?RESID=7B7FCCC78623B4E2%21153

  The unknown device below, is your laptop free fall sensor driver. Please install the driver using the link below.

  [Peripheral problem]

  Error code of device device PNP ID
  Not available ACPI\SMO8810\1 the drivers for this device are not installed.

  ST Microelectronics free fall sensor driver.

  http://www.Dell.com/support/home/us/en/04/drivers/DriversDetails?driverId=CWHJC&FILEID=3201714739&osCode=W764&ProductCode=Alienware-17&LanguageCode=en&CategoryID=UT

  Uninstall Bitdefender, using the uninstall program following the link. Install Microsoft Security Essentials, at least temporarily, until what stabilize us your system.

  Uninstall tools for Bitdefender products.

  http://www.BitDefender.com/uninstall/

  Microsoft Security Essentials.

  http://Windows.Microsoft.com/en-us/Windows/Security-Essentials-download

  Then,.

  You sometimes have a GoFlex, FreeAgent or OneTouch Seagate external drive attached to this system. Please make sure that the drivers for this device are installed correctly, if you do.

  Installing software FreeAgent GoFlex, or OneTouch does not start automatically in Windows.

  http://knowledge.Seagate.com/articles/en_US/FAQ/205515en

• I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  I get an error code whenever I start my computer. I have loaded several packs of registry repair software but cannot get rid of the message. The message bed error loading c:\windows\system32\pofusido.dll the specified module is not found

  Hello

  I googled this file pofusido.dll and it could be caused by a virus.

  I would suggest that you disable the restore mode as viruses use it to reinstall set apart them.

  Download and install the free http://www.malwarebytes.org/

  Restart the computer and keep pressing F8 to get into safe mode with network connection.

  Once you have updated Malwarebytes run and see if it can remove the virus.

  So delete all cookies in your internet Explorer.

  Please keep in mind that my answer is based on the information in your message. More the better I can answer, Slan go foill, Paul

• I have already installed creative cloud and illustrator (trial) but when I turn on the computer and restart windows, it fails with error code 16 and need me to remove the program, and reinstall.

  I have already installed creative cloud and illustrator (trial) but when I turn on the computer and restart windows, it fails with error code 16 and need me to remove the program, and reinstall.

  Need help.

  Hello

  Please see the link below.

  Configuration error. CC, CS

  Hope this will help you.

  Kind regards

  Hervé Khare

• When I print a few sheets even 1 in pdf, I want to show with a different word that I stocked up before the other. What can I do?

  When I print a few sheets even 1 in pdf, I want to show with a different word that I stocked up before the other. What can I do?

  Explain easily, I want to print pdf to distribute people with their name.

  I'm tired of writing the name.

  Hello

  You can use the mail merge to Word for the same functionality and convert it to PDF using the Acrobat plugin.

  Thank you

  Tanvi

• BSOD - Server 2008 R2 - ntoskrnl.exe

  I had a problem recently with a BSOD that passes several times during the day. I newspapers DMP and used BlueScreenView to obtain some basic information (I know that it is also useful that it doesn't help) which seems to show that ntoskrnl.exe is at the origin of accidents. There are 6 Server, 1 is used by the LATTER and does not seem to have had this problem while the other 5 are part of a balanced load environment and have been seen this problem in some cases, 5 times a day. Here are the servers from RD.

  The servers were all working perfectly well until our company has purchased and installed a piece of software called screwdriver. This software seems to be the cause of accidents and I contacted their support in this regard. But while I'm waiting I think it is perhaps a good idea to ask if the DMP files might actually provide more information as to what specifically is causing accidents.

  For those who don't know, the screwdriver is a utility to help you with printing (printing from the Desktop server remotely to the workstation using the screwdriver driverless driver) and I wonder if there is a specific model of printer causing accidents or a driver side specific workstation or if its just one or a few users who cause accidents. Obviously BlueScreenView is not giving any information good but if the DMP file contains more information that might help I understand that it is worth looking into.

  The BSOD error is below:

  Signature of the problem:

  Problem event name: BlueScreen

  OS version: 6.1.7601.2.1.0.18.10

  Locale ID: 1033

  More information about the problem:

  BCCode: f4

  BCP1: 0000000000000003

  BCP2: FFFFFA801CCD9060

  BCP3: FFFFFA801CCD9340

  BCP4: FFFFF80001D85270

  OS version: 6_1_7601

  Service Pack: 1_0

  Product: 18_3

  Files helping to describe the problem:

  C:\Windows\Minidump\112414-48500-01.dmp

  C:\Users\***\AppData\Local\Temp\17\WER-2765148-0.SysData.XML

  Read our privacy statement online:

  http://go.Microsoft.com/fwlink/?LinkId=104288&clcid=0x0409

  If the online privacy statement is not available, please read our offline privacy statement:

  C:\Windows\system32\en-US\erofflps.txt

  Any help is appreciated.

  Thank you

  Ryan

  Ryan

  You should also put this on Technet and I will increase it there as well.

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• New construction various errors usually ntoskrnl.exe - please help

  Recently, I built a new pc and installed Win 8.  A quick components list: i5 - 4670K and ASUS Z87 - has with Corsair Vengeance 16 GB DDR3 1600 Mhz and M500 Crucial SSD 120 GB and WD Green 2 TB HDD (2 x 8).

  Ever since the build, I have known many BSOD with the most common error is IRQL_NOT_LESS_OR_EQUAL is usually assigned to ntoskrnl.exe.

  I went through and updated all the drivers, run MemTest86, re-checked that different settings in the BIOS and MB Web site have where appropriate, although not most new BIOS.  Also have uninstalled antivirus.  Memtest86 showed no memory error.  I'm not totally sure how otherwise to see if a reinstall of Win 8 is necessary.  I believe that it has been updated to 8.1, but not in front of her now.

  Provide advice on things to try.  I have files of dump of crash I can if necessary.  I also reviewed the results of BluescreenView since I started having difficulties.  Tried using driververifier but not sure there's a clue in the BSOD on an interval regular for 3 to 5 minutes, I had with DRIVER_VERIFIER_IOMANAGER_VIOLATION or not.

  Any help would be appreciated!  Thank you.

  Correction of this problem.  Finally found where some BIOS memory settings were not optimized.

• BSOD with error code Bugcheck: 0xD1

  Original title: the dreaded BSOD.

  Hi, finally bite the bullet and ask for help.

  Establish an office a few years back who worked perfectly without any problem, a couple of years, I decided it was time to upgrade and replaced the motherboard, RAM and graphics card with a clean install of Windows 7. He ran very well with some heavy for a week or two games and then the first BSOD came, nothing thought and turned down my graphics settings and tried to play again and then he started blue screening 5 minutes of any game. After many graphics driver reinstall (with driver sweeper), memtest runs and HD check blue screens have continued and I finally gave up on it.

  Fast forward 2 years, I made another attempt on the desktop, 10 hours of updates Windows and updates of pilot followed a complete with MSE analysis and I booted up Fallout New Vegas, the game ran perfectly for 2 days and then blue screens started.

  Help please!

  Processor: AMD Phenom II x 4 955

  RAM: 2x2gb Crucial

  Mobo: Asus M4A785TD-V Evo

  OS: Windows 7 64-bit

  PSU: Corsair CX500

  GPU: Gigabyte Nvidia GTX460

  No overclocking

  Information System

  Minidumps

  DriverView

  WhoCrashed reports

  Friday, April 18, 2014 11:18:08 GMT crashed your computer
  crash dump file: C:\Windows\memory.dmp
  This was probably caused by the following module: dxgmms1.sys (dxgmms1 + 0xAA2A)
  Bugcheck code: 0xD1 (24, 0 x 2, 0 x 0 x 0, 0xFFFFF88004172A2A)
  Error: DRIVER_IRQL_NOT_LESS_OR_EQUAL
  file path: C:\Windows\system32\drivers\dxgmms1.sys
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: DirectX Graphics MMS
  Bug control description: This indicates that a kernel-mode driver attempted to access pageable memory with a high IRQL.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in a standard Microsoft module. Your system configuration is perhaps incorrect. Maybe this problem is caused by another driver on your system which cannot be identified at this time.

  Thursday, April 17, 2014 22:38:20 GMT crashed your computer
  crash dump file: C:\Windows\Minidump\041714-27861-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
  Bugcheck code: 0x3B (0xC0000005, 0xFFFFF80002FABB05, 0xFFFFF88007EB6E30, 0x0)
  Error: SYSTEM_SERVICE_EXCEPTION
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that an exception happened during execution of a routine that passes from non-preferred to the privileged code code.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Thursday, April 17, 2014 22:09:37 GMT crashed your computer
  crash dump file: C:\Windows\Minidump\041714-68921-01.dmp
  This was probably caused by the following module: ntoskrnl.exe (nt + 0x75BC0)
  Verification of error code: 0 x 50 (1, 0xFFFFF80002E86E49, 0xFFFFF88006C3D000, 0 x 0 x 0)
  Error: PAGE_FAULT_IN_NONPAGED_AREA
  file path: C:\Windows\system32\ntoskrnl.exe
  product: Microsoft® Windows® Operating System
  company: Microsoft Corporation
  Description: NT Kernel System &
  Bug control description: This indicates that invalid system memory was referenced.
  This seems to be a typical software driver bug and is not likely to be caused by a hardware problem.
  The accident took place in the Windows kernel. Maybe this problem is caused by another driver who cannot be identified at this time.

  Thank you!

  I would remove the stick that failed and operate the system for a few days.

  Kind regards

  Patrick

• several loops with error handling and controll

  I have a project where I spin 4 loops at the same time and must stop all the loops with a stop button as well as all the loops if one of the loops will receive an error.

  Loop 1.

  Loop start

  control the other 3 loops

  Loop 2.

  Analog voltage reading

  Loop 3.

  Digital inputs to read

  Loop 4.

  Write digital output

  Someone knows how to do this?

  Two other methods not mentioned in the otherwise excellent document that mentioned Matt are the use of a global variable 'stop all' and a relative using a Global Variable of VIG/functional.  The reason to talk about, is that they can be used also stop 'detached' live, live which are defined to run asynchronously (and therefore a bit 'out of control') regarding the main VI.

  I use a "combination of ingredients" for some projects I'm developing using LabVIEW 2016 and its support of the channels.  For example, I use a Messenger channel to create something akin to a message in queue manager.  When the event loop detects that the exit button has been pushed back, it puts a Message "Exit" on the channel of Messenger and stops himself.  When the Message Loop sees "Exit", it sends one release Message who else has need to see (in one case, the producer of a producer/consumer model) and stops himself.  When the producer Gets the output Message, it puts a "last element is invalid" on the flow of the channel for consumers and stops himself.  When the consumer gets the message of the last element, he stops himself.  A magnificent waterfall.

  And I work (not yet 100% complete) how to extend this to start the asynchronous calls that do not (yet) support channels as easily...

  Bob Schor

• Help with error narrow bridge, I can't find where the bridge is always open.

  I try to install In Design. I get a message to close the bridge.

  So I left the bridge, did not help.

  I went to Task Manager > processes and endedbridge.exe, nothing helped.

  I opened bridge, disabled the option of starting with a log, logged in, reconnected again and started the installation again. Still did not help.

  I looked into the process from the Task Manager and I don't see that would be linked to the bridge, but I still get the error.
  

  I've looked through the link "work with your operating system" and can not find something here that is open.

  I am running Windows 7.

  Ah ha! I think it worked. I checked "show processes from all users" and another account had bridge.exe running.  Who finished and it seems to work, yay!

  I am answering my own question for others who may have the same problem

• Error constant csc.exe 550 d NB during the shut down

  Hello!

  Got a new Toshiba mini netbook today and here is my problem:
  I always get an error of csc.exe when close my completely new installed windows7.
  Install microsoft .net cadre4 - as always suggested - does not solve the problem.
  Someone here to help me?

  Hello

  I put t I have this problem, but internet is full of discussion that is this csc.exe and how to solve.
  Have you tried Googling autour solution?

  Try http://www.cscexe.com/ or http://www.sevenforums.com/software/124278-csc-exe.html

  Please send comments.

• Received this error code when trying to install win 10. the message was ' ' has no 1 update "and"windows update has encountered an unknown error."

  Original title: error code 88982F04

  Received this error code when trying to install win 10.   the message was ' ' has no 1 update "and"windows update has encountered an unknown error."  I have win 7 Home premium SP1 running on a desktop HP Pavilion p7-1210 PC.  Can someone please help with an answer.

  Thank you

  Delete C:\$WINDOWS.~BT

  Open the C:\ drive, and then delete the folder: C:\$WINDOWS.~BT and then restart your computer, and then try to upgrade again.

  

  If the upgrade of Windows 10 Assistant becomes blocked or unresponsive to different percentages: 0%, 32%, 62%, 87%, 99%, please wait at least 4 to 7 hours. If the installation program does not progress, close the wizard and restart your computer. Follow the instructions to upgrade manually by using the tool of creation of media or file ISO for Windows 10.

  If you find it difficult to do some of the steps below, please see instructions how do their:

  http://windows10forum.com/blogs/entry/3-How-to-ensure-a-smooth-upgrade-to-Windows-10-anniversary-update/

  If you encounter an error about enough space to perform the upgrade, see the instructions:

  How to install Windows 10 on devices with limited space

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10
  • How to: 10 things to do if the Windows 10 install fails.

  Retry the upgrade manually:

  Option 1: Using the media creation tool

  Download the media creation tool

  Click with the right button on the MediaCreationTool.exe file and then click on run as administrator.

  

  Note: How to check if you are downloaded or installed the update Windows 10 November

  Select upgrade this PC now and then click Next

  

  Option 2: upgrade using the file ISO for Windows 10.

  Task of pre-required

  When you make significant changes to your computer for example updated operating system, you must always back up. See the links to resources on the backup by clicking the link for each version of Windows you are using: Windows XP, Windows Vista, Windows 7, Windows 8/8.1

  • How to back up and restore your files manually
  • How to free up disk space in Windows
  • How to: 10 tips before installing Windows 10

  then

  • How to download official Windows 10 ISO files
  • How to: upgrade previous versions of Windows using the file ISO for Windows 10

  then

  • Turn off (preferably uninstall) your Antivirus utility before you perform the upgrade.
  • Reboot several times, and then try again.
  • Disable the general USB peripherals (for example - smart card reader). You can do so from the Device Manager.
  • If you have an external equipment, attached to the machine, unplug them (example, game controllers, USB sticks, external hard drive, printers, peripherals not essential).
  • Support your default BIOS reset BIOS.
  • Check if there BIOS updates available for your system, and then to apply them.
  • If you are using a SCSI drive, make sure you have the drivers available for your storage on a USB device and it is connected. During the installation of Windows 10, click on the advanced custom Option and use the command load driver to load the driver for the SCSI drive. If this does not work and the installer still fails, consider switching to an IDE based hard drive.
  • Perform a clean boot, restart, and then try again.
  • If you upgrade to the. ISO file, disconnect from the Internet during the installation, if you are connected in LAN (Ethernet) or wireless, disable both, then try to install.
  • If you are updated through Windows Update, when download reaches 100% disconnect from the LAN (Ethernet) Internet or Wi - Fi, then proceed with the installation.
  • If this does not work, try using the. ISO file to upgrade if possible.
  • If you are connected to a domain, go to a local account.

• Lightroom 3 (to 3.6) - "an error occurred when attempting to change modules" - is the message that I get by clicking on expand or any other option. I deleted and reinstalled the .dmg file, but it continues still to be. Can anyone help?

  I just downloaded Lightroom 3 (to 3.6) and once I installed and opened it, it said that there is an error changing modules. I deleted and reinstalled the .dmg file, and it still gives me this error. Can anyone help?

  Error changing modules | Lightroom

• STARTING in the same column several times with 2 different condition

  Hello world
  
  I have a small question, but I can't find the answer. Can someone help me with this one? Look at this example:
  

  WITH T AS (
    SELECT 'a' as Name, 1 as v FROM DUAL
    UNION ALL
    SELECT 'a' as Name, 2 as v FROM DUAL
    UNION ALL
    SELECT 'a' as Name, 2 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 1 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 1 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 2 as v FROM DUAL
  ) SELECT DISTINCT name, 
           COUNT(DECODE(v, 1, 1, null)) OVER (PARTITION BY name ORDER BY v) as v1,
           COUNT(DECODE(v, 2, 1, null)) OVER (PARTITION BY name ORDER BY v) as v2
      FROM T
    ORDER BY 1;

  This returns:
  

  NAME V1                     V2                     
  ---- ---------------------- ---------------------- 
  a    1                      0                      
  a    1                      2                      
  b    2                      0                      
  b    2                      1                      

  But what I need in a single row with the count of 1 and 2 by name. How can I get without using subqueries as (the following query returns the correct result)
  

  WITH T AS (
    SELECT 'a' as Name, 1 as v FROM DUAL
    UNION ALL
    SELECT 'a' as Name, 2 as v FROM DUAL
    UNION ALL
    SELECT 'a' as Name, 2 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 1 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 1 as v FROM DUAL
      UNION ALL
    SELECT 'b' as Name, 2 as v FROM DUAL
  ) SELECT DISTINCT t.name, 
           (SELECT COUNT(*) FROM T z WHERE z.name = t.name and z.v = 1),
           (SELECT COUNT(*) FROM T z WHERE z.name = t.name and z.v = 2)
      FROM T t
    ORDER BY 1;

  The table I'm working on that has millions of records with subqueries it takes forever to run. The one with the analytical function takes less than 3 seconds.
  
  
  Thanks for your help!

  If I understand correctly, you need a global tally, not an analytical account. Something like:

  SQL> WITH T AS (
    2    SELECT 'a' as Name, 1 as v FROM DUAL
    3    UNION ALL
    4    SELECT 'a' as Name, 2 as v FROM DUAL
    5    UNION ALL
    6    SELECT 'a' as Name, 2 as v FROM DUAL
    7      UNION ALL
    8    SELECT 'b' as Name, 1 as v FROM DUAL
    9      UNION ALL
   10    SELECT 'b' as Name, 1 as v FROM DUAL
   11      UNION ALL
   12    SELECT 'b' as Name, 2 as v FROM DUAL)
   13  SELECT name, COUNT(DECODE(v, 1, 1, null)) v1,
   14           COUNT(DECODE(v, 2, 1, null)) v2
   15  FROM T
   16  GROUP BY name
   17  ORDER BY 1;
  
  N         V1         V2
  - ---------- ----------
  a          1          2
  b          2          1
  

  John