SG500-28 2 switch battery Configuration Question

Similar Questions

• How can I switch between configurations in XCode 7?

  I use XCode 3.2 on Snow Leopard. This week I also bought a new iMac and installed XCode7 on it. It is completely different and is not entirely clear. With the old XCode, I have a menu at the top left of the project window. I use this menu to switch between the two configurations (debug and release). I can't understand what is the equivalent in version 7. Also, I find the target compiled in its usual place (the 'build' folder). I can find it elsewhere with the projector, fortunately. So my main problem is: how to switch between configurations? The problem is: How can I know who is the active configuration? I will be grateful to anyone who is kind enough to help me.

  Use the schema editor in the toolbar to set the active build configuration. It is next Run and Stop buttons. Click on the name of your application to open a menu. Choose change the schema to open the schema editor.

  

  You can set the active build configuration in the stage of the race.

  

  Xcode changed a ton in Xcode 4. If you're in transition to Xcode 3.2, you can find the following useful:

  Xcode Tools Tips

• Unity double switch integration - licensing question unity 4.0 (3)

  Unity double switch integration - licensing question unity 4.0 (3)

  The unit was sold as a single IP integration. My client needs Dual Switch with an Ericsson PBX. I received the license key of ORC, and I opened a folder of TAC.

  TAC said that the license file will not allow installation double switch integration. The Cisco SE on the account indicates that the license key will allow me to make the integration of the double switch.

  Who is right? I heard that the moderator here has all the answers :)

  The is correct. Any customer with a license 4.0 can do double switch. You don't need a special permit.

  Thank you

  Keith

• VMware switch Vlan configuration

  It is possible to switch the configuration that resembles a vmware

  interface GigabitEthernet0/4

  Description calculate node 1 eth1

  switchport trunk vlan 100 native

  switchport trunk encapsulation dot1q

  switchport trunk allowed vlan 100, 101 102

  switchport mode trunk

  spanning tree portfast trunk

  on the gigabitEthernet 0/4, I have a linux machine that needs these config.

  Thank you!

  Ah, very good. Sorry for my confusion!

  Yes, you can do it.

  interface GigabitEthernet0/4

  Understand and document how the switchport is connected to your ESXi host.  When you start, your ESXi host lists its physical network cards, called vmnic.  Enable CDP on your vSwitches (or LLDP if you use a vDS) so that you know how your ESXi host connects to the North.

  Description calculate node 1 eth1

  You cannot configure the descriptions on vSwitches Standard (you * can * configure them on a vDS). You can also, of course, port name groups however you like, with a few caveats.

  switchport trunk vlan 100 native

  The virtual switches VMware isn't exactly the notion of VLAN native.  If you want to leave the untagged packets ESXi host, you don't assign just one VLAN to that particular port group.

  
  

  switchport trunk encapsulation dot1q

  VMware only use 802. 1 q of marking.  There is no need to explicitly configure.  In addition, you can't.

  
  

  switchport trunk allowed vlan 100, 101 102

  Create a VLAN that you like on the ESXi hosts using the parameters of port group VLAN.  Don't forget not to set up a local VIRTUAL network for the port group that hosts the VLAN native.

  
  

  switchport mode trunk

  ESXi hosts accept several VLANs on a vmnic out of the box.  There is no need to configure.

  
  

  spanning tree portfast trunk

  This option isn't strictly for switching equipment, end-hosts as ESXi.  Your ports ESXi NIC will come as soon as possible.

  -----------------------------------------

  Remember to mark this reply 'proper' or 'useful', if you found it useful.

  Mike Brown

  NetApp, VMware and Cisco data center guy

  Consultant engineer

  [email protected]

  Twitter: @VirtuallyMikeB

  Blog: http://VirtuallyMikeBrown.com

  LinkedIn: http://LinkedIn.com/in/michaelbbrown

• 3750 stand-alone switch battery change error message displays

  We have some 3750 autonomous through our network. IT restarts automatically. through the history of logging, it shows Stack_Link_Change message but this switch is autonomous.

  ---------------------------------------------------------------------------------------

  C3750-1 # sh version
  Cisco IOS software, software C3750 (C3750-IPBASE-M), Version 12.2 (35) SE5, RELEASE SOFTWARE (fc1)
  Copyright (c) 1986-2007 by Cisco Systems, Inc.
  Updated Friday 19 July 07 19:15 by nachen
  Image text-base: 0 x 00003000, database: 0 x 01080000

  ROM: Bootstrap program is C3750 boot loader
  BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M), Version 12.1 (19(r)) EA1b, VERSION of the SOFTWARE (fc2)

  The availability of C3750-1 is 3 hours, 11 minutes
  System to regain the power ROM
  System restarted at 23:22:58 GMT Monday, August 8, 2011
  System image file is "flash: c3750-ipbase - mz.122 - 35.SE5.bin".

  Cisco WS-C3750 - 24 p (PowerPC405) Prozesseur (D0 revision) 118784K / 12280K bytes of memory.
  Card processor ID CAT0847N0Y3
  Last reset of tension
  4 virtual Ethernet interfaces
  24 FastEthernet interfaces
  2 gigabit Ethernet interfaces
  Password recovery mechanism is activated.

  512K bytes of memory simulated by flash not volatile configuration.
  Basic Ethernet MAC address: 00:12:80:65:94:00
  Number of the motherboard: 8312-73-05
  Power supply part number: 341-0029-03
  Motherboard serial number: CAT08470DDE
  Power supply serial number: LIT0841015S
  Revision number of the model: D0
  Motherboard revision number: A0
  Model number: WS-C3750-24PS-S
  System serial number: CAT0847N0Y3
  Top Assembly part number: 800-21982-02
  Top of page revision number of the Assembly: B0
  Version ID: n/a
  Revision number of hardware consulting: 0x0A

  SW Version SW Image model switch ports
  ------   -----  -----              ----------              ----------
  * 3 26 WS-C3750 - 24 P 12.2, C3750 SE5 (35) - IPBASE-M

  Configuration register is 0xF

  ---------------------------------------------------------------------------------------------------------------

  C3750-1 #sh logging

  * Mar 1 05:00:33: % SYS-5-CONFIG_I: configured from the system memory

  * Mar 1 05:00:33: STACKMGR-5-SWITCH_READY %: switch 3 is READY

  * Mar 1 05:00:33: STACKMGR-4-STACK_LINK_CHANGE %: battery Port 1 3 switch has changed state down

  * Mar 1 05:00:33: STACKMGR-4-STACK_LINK_CHANGE %: battery Port 2 switch 3 has changed state down

  * Mar 1 05:00:34: % STACKMGR-5-MASTER_READY: Master Switch 3 is READY

  * Mar 1 05:00:34: % LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, state change downstairs

  * Mar 1 05:00:34: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Vlan48, change of State down

  * Mar 1 05:00:34: % SYS-5-RESTART: System restarted.

  Cisco IOS software, software C3750 (C3750-IPBASE-M), Version 12.2 (35) SE5, RELEASE SOFTWARE (fc1)

  Copyright (c) 1986-2007 by Cisco Systems, Inc.

  Updated Friday 19 July 07 19:15 by nachen

  * Mar 1 05:00:34: % SNMP-5-start COLD: SNMP agent on host C3750-1 shall be the subject of a cold start

  * Mar 1 05:00:35: % LINK-5-CHANGED: Interface FastEthernet3/0/22, changed state down administratively

  * Mar 1 05:00:35: % LINK-5-CHANGED: Interface Vlan1, changed state down administratively * Mar 1 05:00:33: % SYS-5-CONFIG_I: configured from the system memory
  * Mar 1 05:00:33: STACKMGR-5-SWITCH_READY %: switch 3 is READY
  * Mar 1 05:00:33: STACKMGR-4-STACK_LINK_CHANGE %: battery Port 1 3 switch has changed state down
  * Mar 1 05:00:33: STACKMGR-4-STACK_LINK_CHANGE %: battery Port 2 switch 3 has changed state down
  * Mar 1 05:00:34: % STACKMGR-5-MASTER_READY: Master Switch 3 is READY
  * Mar 1 05:00:34: % LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10, state change downstairs
  * Mar 1 05:00:34: % LINEPROTO-5-UPDOWN: Line protocol on the Interface Vlan48, change of State down
  * Mar 1 05:00:34: % SYS-5-RESTART: System restarted.
  Cisco IOS software, software C3750 (C3750-IPBASE-M), Version 12.2 (35) SE5, RELEASE SOFTWARE (fc1)
  Copyright (c) 1986-2007 by Cisco Systems, Inc.
  Updated Friday 19 July 07 19:15 by nachen
  * Mar 1 05:00:34: % SNMP-5-start COLD: SNMP agent on host C3750-1 shall be the subject of a cold start
  * Mar 1 05:00:35: % LINK-5-CHANGED: Interface FastEthernet3/0/22, changed state down administratively
  * Mar 1 05:00:35: % LINK-5-CHANGED: Interface Vlan1, changed state down administratively

  The bugs that I've provided are also associated with stand-alone switches, I can't share bug internal details.

  I've seen this problem before, & I understand that it is a standalone switch.

  Most of the time that it would be because ports of defective battery which can not really be detected there software. I also looked at the case attached to the bug & found a few similar cases.

• Network configuration question

  I'm one of our 5.5 hosts replace with new material and want to make sure that I get the right networking. We have unit vcenter and a HA cluster with shared on an EQ San storage and complete double switches for redundancy. My old hosts have 2 quad port NIC, so configure each vswitch with double vmnic for a total redundancy was easy - I split each pair on the physical network interface cards. If one of the physical network cards is dead, I was still all my connections.

  The new host has 1 quad port nic and dual 2 network cards to port. Network interface cards double port match and have tcp offload capabilities, but the quad port does not. I want to use the dual port 2 for my iscsi and vmotion, so that leaves the quad port for my public connections. What happens if the public NIC dies, especially if they vcenter on this host? I know that all the virtual machines will still work, but will they automatically vmotion to other hosts if only the public network fails?

  Thank you.

  NIC failures are very rare. So, I would place too much emphasis on this scenario.

  Is the answer to your question, it depends. HA has a configuration option called isolation response of the host, who controls what happens when the host loses connectivity management. By default, it is configured to leave it powered on. You can change it to Shut Down, which makes sense in your scenario, as the loss of connectivity management means the loss of connectivity to the virtual machine as well. And in this way when management network goes down all your virtual machines is gracefully closed and restarted on another host.

• WRT320N used as switch gigabit single - Question

  Hello friends,

  I use WRT320N a few days now and I'm happy with it so far! It has not overheated as many people reported and performance is also great (wifi and gigabit ports). I tested all the functions (NAT, Advanced Wireless Settings, Port Forwarding,... Access Restrictions) - all the great work, but I'm bit stuck on that easier - temporarily configure it as regular gigabit switch with an IP address: I put my cable WAN and LAN cables in ethernet ports 1-4. NAT, DHCP and firewalls are disabled in the router. I have the DHCP server in my network which is based on the MAC address IP address assignment. In "Setup" > "Basic settings" > "Router IP," I want to set up automatic configuration - DHCP, but it is not possible, so I just type the same IP address, it must obtain from the DHCP server (in this case 10.109.249.42). All ethernet ports 1-4 has the same MAC address (in this case, 00:25:9 C: 4 d: 16:86)?

  Everything works fine, my computer's IP addresses are correctly assigned (as well as wifi devices) from the DHCP server on my network, but I feel like WRT320N address is unaffected - the problem is that I can't connect to the router under http://10.109.249.42 administration. There is no IP restrictions for remote management. Any ideas?

  Screenshot of my "status" > "Local network".

  

  Routers Linksys WRT are not designed to be used as a simple access point/ethernet switch. That's why you won't find any configuration options you like for this configuration. You must configure a static IP address to the address LAN IP on the WRT. There's no other way. It's always a static IP address. The WRT will never get the address LAN IP of the server because it is designed to serve as a internet gateway and the DHCP server.

  It is clear to me why you are not able to access http://10.109.249.42/ while you are able to access the status page...

  Is the computer from which you are trying to access the router within the 10.109.249. *?

• New Network Configuration Question

  Out of my element here, have a new building we are evolving towards and want to check the right way to install our network. Rooms include 1 - TZ-200, 1 - LAN + Modem wireless switch dell 1-2824 (data), switch dell 1-2824 (voice), 1 - security DVR. If I configure the TZ-200 to the dhcp server, remove the dsl, taken in the wan port modem dhcp will be the sonicwall pick up the wireless and purge the IP for wireless addresses, as well as configure the remaining ports on TZ-200 LAN will all devices to be on the same subnet/nat for easy access? can provide simple schema, if that helps.

  Forget the feature wireless modem from your Internet service provider. You cannot have two routers 'work' (not in this configuration in any case). The only jobs of the modem is to feed the WAN in the Sonic and the Sonic is one that will manage all SonicOS is designed for, such as the creation and serving Dhcp. unless you are forced by the ISP contract to use the material they gave you, it may be more easy to get just a modem ADSL2 + regular that you can find in any * sale because they are unpopular with the houses of our days.

  To get WiFi in your network, you will fill a WiFi 'something' to one of the LAN in the Sonic ports. It can be of any router wireless of quality home set in Bridge mode (all DLink, Netgear, Linksys, etc, they can all work such as bridges), or a wireless bridge of commercial quality (as Unifi AP).

• Cisco asa active multiple interfaces on a single switch without configuration of vlan switch.

  I was wondering if there is a work around on cisco asa to have 2 interfaces vlan on a switch. The reason I ask I have a cisco asa 5505 and a dell switch that does not support the configuration of VLANs. I set up 2 interface vlan on a cisco asa and when two interfaces are active my internet drops frequently. I was wondering if there is nothing to configure the asa cisco to make this thing work. Thanks in advance...

  Assuming that Dell switch at least linking several interfaces of the ASA to the Dell should translate all media spanning tree protocols, but a bet covering the tree blocking State to avoid a tree covering loop.

  If the Dell does not support tree covering weight then you would be in very bad shape each broadcast packet would be will loop indefinitely and cause what we call a 'broadcast storm. "

  One way is not good and the other real harm.

• HA Configuration questions

  Probably a simply and silly question but...

  I'm having a problem with HA on one of my groups.  At the cluster level, I have a message indicating ' insufficient resources to meet the HA level of failover cluster < name of the cluster > < name datacenter >.»  Failed to contact a senior officer of HA cluster < name of the cluster > < name data center >

  Each of the 6 guests in the show cluster has an error with the HA Agent on < Home > cluster < cluster name > < datacenter name > has an error: error when running script control of health.

  Now, looking at them HA at the cluster level, see someone (many ahnds in the kitchen I guess) enabled DPM under admission control.  I disabled that so that it matches my other clusters that are precisely be works very well.  I selected "reconfigure HA" on all hosts, but the process fails. "Cannot complete the configuration of the HA agent on the host.  Impossible to contact agent HA primary. »

  So I think that if I just disable HA on the cluster and back depending on who he might rectify the issue.

  2 questions:

  1 will be solve my problem

  2. If #1 will be, shutting down HA affects the virtual machines running on 6 other guests that endangering temporarily?

  Thank you

  Casey

  Deactivation and reactivation HA on the cluster will probably fix the problem.

  See here: http://kb.vmware.com/kb/1021173

  And you should do this as soon as POSSIBLE, because NOW your virtual machines are already vulnerable, because HA currently does not work properly.

  Turning off HA and will not affect the virtual machines in any way, except to put them at risk of not be restarted automatically in the event of a host failure.

  -Andreas

• Configuration questions

  Hello

  I'll put up a new configuration to increase the availability of the virtual machine

  I have a 3.0 license for 4cpus ESX Server that manages all the vm I

  What I wanted to do is setup in the image below

  The virtual machine (about 6) is stored on NAS1 and their management divided by 2 servers

  NAS2 is synchronized with nas1 (with rsync)

  If a server goes down, another one will manage the virtual machines.

  If a NAS fails, I'll use the virtual machines on the other.

  My questions are these, if you guys could please answer none of them I appreciate it:

  (1) ESXi will run on a quadruple-heart machine even if its license is for 2 cpu or will it does not at all?

  (2) is there any compatibility issue on moving the virtual machine on the esx 3.0 Server server esxi 4.0?

  (3) can I synchronize two SINS while VMS are running?

  (4) do you think that any problem with this configuration?

  Bye,.

  uilli

  > 1) Will run on a machine four hearts, ESXi even if its license is for 2 cpu or will it does not at all?

  Licence is issued for sockets, no carrots. So 1 quad core CPU needs 1 license.

  (> 2) is there a compatibility issue with the movement of the virtual machine on the esx 3.0 Server server esxi 4.0?

  N °

  (> 3) can I synchronize two SINS while VMS are running?

  Best way is cold migrate virtual machines to the new data store. In fact, it is the only way.

  ---

  MCSA, MCTS Hyper-V, VCP 3/4, VMware vExpert

  http://blog.vadmin.ru

• Newbie on iSCSI Configuration questions

  Hello everyone

  I'm new to VMware. I have two questions

  (a) once I have add an address IP of SendTargets discovery, how can I update it? for example, if a new target is visible via the IP discovery after that it has already been added in VMware and I want it to appear.

  (b) is there a provision the disconnection of one specifying IQN (San identifier)? I went though VSphere Documentation and I couldn't find anything.

  (c) VSphere he iSNS support such as Linux (iscsiadm)?

  Thank you

  Welcome to the Forums-

  (a) you will need to go to the section of the configuration of the ESX host storage card in the client vSphere select initator iSCSI, then click Rescan - this cause a target command send sending sllowing to the discovery of new targets

  (b) No, there isn't a way to disconnect from a specific IQN I know

  (c) to the vSphere, I think not vSphere supports iSNS.

  If you find this or any other answer useful please consider awarding points marking the answer correct or useful

• Boot from SAN Configuration Question

  Asked me to start deloying new hosts ESX 3.5 using Boot from SAN.  All the documentation I've found is clear on the configuration of HBAS and SAN lun.  I tried to find out what the correct design for the HBA boot ports and storage used.  Does anyone have info on the Boot/operating system as well as the storage of data on the same HBA ports.  This design would be only two HBA by using a port of each for failover.  I also plans to isolate the boot/OS on his own two redundant ports but get resistance from my SAN Group on the fact we use two additional ports turned on by host.  After a few unsuccessful attempts with VMware support, I finally got someone to give me one different answer a document on how to put in place the HBA and SAN.  I was told that sharing should be fine but I also met some files indicating that you must keep them separately.

  Hello

  There is no question share the wwn for a startup process.

  The key here is to always book LUN 0 for the reader to boot/OS on all systems.

  I have 12 guests thanks to her, and there is no sound technical reason to isolate him.

  Kind regards

  Mike

  http://blog.laspina.ca/

• PERC 5i RAID Controller battery replacement Question

  Part number Quantity Description

  WX072 1 Assembly, Card (Circuit), Serial Attached SCSI PERC5I, 1950, 2950

  TX846 1 THE ASSEMBLY, CABLE, CONTROL, SERIAL ATTACHED SCSI, POWEREDGE EXPANDABLE RAID CONTROLLER NUMBER

  Hi all

  I have a general question, I need help answering: Server is a Dell PowerEdge 1950

  I have an E1211 ROMB BATT on LCD screen and replace the battery. With the above specifications showing that our part number based Service tag, the following link below would be ok to order from?

  https://www.Google.com/shopping/product/11727795338555807657?sclient=psy-AB&q=PERC5I+serial+attached+SCSI+battery+TX846&OQ=PERC5I+serial+attached+SCSI+battery+TX846&PBX=1&BAV=on.2, or.r_cp.r_qf & bvm = bv.63808443, d.cWc, pv.xjs.s.en_US.9CjFb4DKbRI.O & biw = 1301 & bih = 678 & tch = 1 & ech = 1 & psi = uLs5U_SHCNXLsASN7IKYBg.1396292536397.11 & ei = 1745U8PVI4XIsAT8voCwAQ & ved = 0CJMEEKYrMAM

  Is there best kinds of batteries that this RAID controller could use compared to the one we intend to order?

  Please notify.

  Thank you

  Hiphoptech

  You might consider updating the controller firmware (after are updated BIOS, ESM and the controller driver), which controls the State of the battery.  Otherwise, the battery that you accessed should be good... it is not really other "types" of batteries that will work.

• remote server configuration question

  Hello
  
  I have my web app works fine on a local apache/php/mysql server. but now I'm doing work on the remote server. so far, no luck. a few questions:
  the connection to the base for my local server has a user id and password. can I use the same username and password for the mysql database remote?
  I understand how to connect the db to the apache server locally (I use port 8080), but I don't understand how the apache finds the right mysql database on the remote server. do I have to use the db connection in the application of dw Panel and modify the connection settings somehow it can therefore be used for the remote server? I noticed that I get an error: the requested URL doglist.php was not found on this server.
  
  Additionally, a 404 not found error was encountered while trying to use an ErrorDocument directive to manage demand.
  Apache/1.3.37 Server at www.counselorone.com Port 80
  
  Thanks in advance for all advice.
  Mike

  David and Gareth Murray.

  Thanks for your help. The last piece was dense enough to me, but I got it. David, I know that you deal with in your book, but you could probably devote a special section, its that delicate. The nuts and bolts of what I've done is...
  1. to develop my unconscious site at the remote server, including making local database connections. Because microsoft IIS stored in my own way, I changed the port of Apache on 8080. After reading David's comments, I think that its smarter to simply not bother to change the Apache port and manually turn off the IIS application. OR, you can go back once you have created the site and edit your config file Apache backwards to port 80, because you will need the localhost, not localhost: 8080 to connect to the remote server. To avoid pulling the hair, just to deal with the default configuration of apache on port 80.
  2 hire a remote hosting company. I use the server range, although I have not been with them long enough to give a thumbs up or thumbs down.
  3. put the local site on the remote server. I used public_html to store my files.
  4. download the remote server to connect to the database. This last part seemed to require a few things, which were not obvious. Following the advice on this forum, I went to the remote site and note the username, password and database name. (these are NOT the same as my local site). I then copied/renamed my database on the local site to match with the prefix than the remote server has put on my remote database. For example my db was named test1 locally, but the server named wwwcoun_test1, so I renamed it which.
  5. I tried to establish a connection to the database with the new names. It worked. my understanding is that everything we try to do here is set up the connections correctly. you're dealing with loading data in the database with phpmyadmin, a great time-saving tool.
  6. I went on site remote and typed in the url for files downloaded to see if they would connect to the database. they did it.

  That's all. Hope this story helps the next person who needs help.

  Yet once again, thank you very much to those who responded. I appreciate your support.

  Mike