Should I stop, restart, or put my computer windows 7 standby?

Similar Questions

• Windows vista update 3 of 3 will not set up, computer continuously, stop and restart; Unable to access computer

  Windows vista update 3 of 3 will not set up, computer continuously, stop and restart; Unable to access computer

  The link below has options to solve your problem of loop.

  http://support.Microsoft.com/kb/949358>

  04:17:0407/17/11

• Why when I put my computer to sleep it restarts?

  Sometimes when I put my computer to sleep, it instantly reboots. Its very frustrating because, then I have to wait for it to start so I can try to put it to sleep again, and it restarts again, so I just leave it or close it.

  Why my computer does not restart instead of go to sleep?

  Hello

  Check your settings (BIOS/CMOS) - usually F2 as you start - Wake on Lan, Wake on Modem and so on.

  Troubleshooting Windows Vista sleep and extended
  http://www.computerperformance.co.UK/Vista/vista_hibernate.htm

  How to troubleshoot performance problems with sleep, hibernation and resume in Windows Vista
  http://support.Microsoft.com/kb/950686

  May need to reset all to default power settings and then place back as you prefer.

  How to solve a problem of Mode for Vista and find a Solution
  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  How to enable and disable Hibernation - you can try to disable and re-enable the it. http://www.Vistax64.com/tutorials/165508-hibernation-enable-disable.html

  How to restore the default power in Vista (and then go back and change as you wish)
  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  Panel configuration-Device Manager - look at the settings for the network card, WiFi, Modem power management.
  and other devices. (Double click on the device and the power management tab)

  May need to reset all to default power settings and then place back as you prefer.

  I hope this helps.
  Rob - bicycle - Mark Twain said it is good.

• When I put the computer on the mode 'sleep' it goes into sleep mode and then restarts on its own.

  Have Vista Home Premium. When I put the computer on the mode 'sleep', it closes and moves to the State of low consumption with the screen. But in a few seconds without touching the key or mouse it starts again. What is going on?

  Hello

  See if this information helps you:

  "How to restore the default power Plan settings in Vista"

  http://www.Vistax64.com/tutorials/198047-power-plan-restore-default-settings.html

  "How to solve a problem of Mode Vista or Windows 7 sleep"

  http://www.Vistax64.com/tutorials/63567-power-options-sleep-mode-problems.html

  See you soon.

• I wanted to shoot penalty, put the computer in safe mode, now its blocked, firm FF 3 times, computer rebooted, still in safe mode.how out safe mode

  I wanted to do in the event of problem, I put the computer in safe mode and now I can't get out of safe mode. I closed FF & computer restarted 3 times, even shut down the computer, still in safe mode. What should I do to get out of safe mode?

  I gave up and took my laptop to the Apple store... everything is ok now... I don't know what they were doing.

• Do a right click on desktop freezes computer, Windows explore and Dr. Watson as time stop working. Only Ctrl + Alt + Delete can be used to reset the computer

  original title: right clicking on desktop freezes the computer, Windows explore and Dr. Watson times stop working.  Only Ctrl, Alt, Del to reset computer

  Make a right click on desktop freezes the computer.  Explorer Windows and Dr. Watson stop working. Only Ctrl, Alt, Del restarts computer

  Hi Ken1948,

  1. did you of recent changes on the computer?

  2. you receive the error message?

  3 when was the last time it was working fine?

  Check if the problem persists in safe mode.

  A description of the options to start in Windows XP Mode

  http://support.Microsoft.com/kb/315222

  It is possible that some third-party programs installed on the computer is causing the problem.

  I suggest that you put the computer in a clean boot state and check if it helps.

  To help resolve the error and other messages, you can start Windows XP by using a minimal set of drivers and startup programs. This type of boot is known as a "clean boot". A clean boot helps eliminate software conflicts.

  See the link below to learn more about how to clean boot.

  How to configure Windows XP to start in a "clean boot" State

  http://support.Microsoft.com/kb/310353

  Reset the computer to start as usual

  When you are finished troubleshooting, follow these steps to reset the computer to start as usual:

  (a) click Start, type msconfig in the search box and press ENTER.

  (b) If you are prompted for an administrator password or for confirmation, type your password or click on continue.

  (c) under the general tab, click the Normal startup option, and then click OK.

  (d) when you are prompted to restart the computer, click on restart.

• How can I reinstall windows I want to put my computer to when it was new

  How can I reinstall windows I want to put my computer to when it was new

  It's an Acer / Dell / HP system? If it is restarting it should tell you which key press to restore the system on the post screen

• Force the print to stop/restart spooler service when it does not

  Our office has a HP plotter, where the driver (note that we have the latest version, directly from the HP site) seems to cause the print spooler service becomes out of order sometimes.  In turn of the programs (including AutoCAD and Outlook) to lock, as well as windows, as the dialog box, which causes devices and printers.

  If I restart the 'Services' print spooler service in computer management, it goes back to work at least some time - if at least I can work around the problem.  It is important to note however, that even by using this method, it throws a dialog box error saying that the service failed.  But since this is a question with all facilities of this liner installed with Vista, I need to have a method easier to use of the service is restarted.

  I wrote a file .bat base with a net stop spooler command followed by a net start spooler command, but the problem is that, unlike with computer management, net stop does not seem to force the service to shut down if it does not, and I can't find a way to force the stop command.

  Is there a tool more powerful/switch available that I could script so that users can easily stop and restart the spooler service when it does not?

  Thank you

  Type sc /?

  --
  ..
  --
  "mgarrison" wrote in message news: d3d768a8-126-b-4246-a4d8-ca6d8f4db6a7...
  > Our Office has a HP plotter, which the driver (note that we later
  (> version, directly from the HP site) seems to cause the print spooler
  > service becomes out of order sometimes. Which causes in turn of programs
  > (including AutoCAD and Outlook) to put him away, windows as the
  dialogue of the RHS.
  >
  > If I restart the spooler service for printing of 'Services' in computer science
  > Management, she goes back to work for at least some time - if at least I have
  > can work around the problem. It is important to note however, that even
  > by using this method, it throws an error dialog box saying that the service
  > did not. But since this is a problem with our Vista
  > facilities having this installed plotter, I need to have a more
  > user-friendly method of restarting the service.
  >
  > I wrote a .bat file to base with a net stop command spooler followed by a
  > net start spooler command, but the problem is that, unlike with a computer
  > Management, net stop does not seem to force the service stops if it is not
  > answer and I cannot find a way to force the stop command.
  >
  > Is there a tool more powerful/switch available that I could then script
  > users can easily stop and restart the spooler service when it is not
  > sensitive?
  >
  > Thank you

• PC counters each attempt to fix/repair and finally, the loop to stop/restart windows Explorer.

  So beyond, I'm done with this laptop. He started by run me windows update and the awakening of a BSOD. Now browse those tedious threads, I know that the next thing people want are the dumpfiles. Well, you cannot make them because it won't create dumpfiles. I checked everywhere for them and double-checked to make sure that when I got bsod it is correctly configured to do. It will not create them. So ok, the next thing people say is running scandisk Sfc. Nope, BSOD in the course. Chkdsk? Nope, BSOD. during the. This laptop has a coherent dpc latency problem where every 10-13 seconds it stings really high, distorting the audio. I tried to disable drivers, update drivers, pulling on the battery, and it won't go away. To * with it I say, I can deal with that, besides there is probably a hardware problem, it's an old inspiron 5040. The greatest success in fixing something comes sfc running in safe mode with cmd prompt. He got to 100% and has absolutely nothing more. All this stems from the windows updates failed. But this latest issue is the water drop. Before the windows explore stopped working/restart loop, which prevents me from running damn near all executable on ANY startup mode, I was getting semi-fonctionnalites off safe mode with network. I was inside my damndest to try to solve the problems without paying a penny for the repair (because it's my operating system from windows to the 3rd address I got incredibly frustrated with questions and I'm NOT GOING to sink more money into the purchase/solve this *) but after a month of countless BSOD and failed system restore (BSOD on those too) I decided to say the * with it , it can still be used for browsing with chrome at least, since I found a way to activate the sounds of the internet registry. I had used it for about a month and realized that internet Explorer was causing in fact a kind of conflicts, because all applications requiring an i.e worked incorrectly, display of white windows resources that need to be pulled with knowledge then I tried to reinstall that is and makes the mistake of restarting, forget the automatic Windows Update. Well, I is none of that with this time and tried to turn off the pc before it started with nothing else than a glorified blue screening method. To restart, I got "windows is the restoration of changes", another reboot, then a "Welcome" I get started in the regular office, (not safe mode or anything like that) and he gives me a small white window with "custom settings" on it and literally nothing else. No toolbar, no desktop shortcuts. Wait a few seconds and I get "Windows Explorer has stopped working" and the option to close the window. safemodes boot loop to stop/restart windows Explorer and I can't do anything appear the Task Manager which is pretty useless, because I can't really do anything here except close programs that are not accessible in the first place. Safe mode only I can enter is the one with the command prompt. I don't really know what else to do. Quite happy to take a hammer and break the laptop for parts. There are so many problems with this thing, I doubt that someone will be able to help in any way especially withouth minidumps the BSOD. But if there is something simple that I'm missing for at least the minimum functionality that I was getting out of it until windows update in ruins me, feel free to try to solve the problems. The code the most common bsod I get is 0xf4. I put my money on half of the problem with the hard drive itself and the rest of the question was any other defective hardware. But ill be doomed if I buy another harddrive just to have more questions.

  Hello

  Generally, this problem is caused due to hardware or software related issues. As you mentioned that you have completed the restoration of the system and sets the Explorer loo, I would like to know if the problem is resolved or not.

  Regarding performance related questions, I would suggest trying the following methods and check if it works for you.

  Method 1:

  Try the procedure described in the following Microsoft Help article and check if that helps. This Microsoft Help article consists of the steps to optimize Windows to improve performance.

  http://Windows.Microsoft.com/en-us/Windows/optimize-Windows-better-performance#optimize-Windows-better-performance=Windows-7

  Method 2:

  Put the computer to boot and check if the problem persists. This troubleshooting will help you find what third-party program or the app is the cause of this problem.

  How to troubleshoot a problem by performing a clean boot in Windows Vista or Windows 7:
  http://support.Microsoft.com/kb/929135 
  Note: After the boot minimum troubleshooting step, see the "How to reset the computer to start as usual after a clean boot troubleshooting" section in the link provided to return the computer to a Normal startup mode.

  Please reply with the status of the issue so that we can better help you.

• Internet connection problem; A few days ago, my computer (Windows 7 OS) stopped connecting to the internet. DNS

  A few days ago, my computer (Windows 7 OS) stopped connecting to the internet. When I troubleshooted, it produces an error of "your computer seems to be configured correctly, but the device or resource (DNS server) does not. I Googled it and tried a lot of things that have been suggested - flushing the DNS, reseting the TCP/IP, etc... None of them worked. At the end of the day, I did a restore of the system to a restore point a few days before starting my computer having these problems and then it started working again. But whenever I have to stop and restart my computer, the problem happens again. Any help as to what could be the problem or how I can fix this problem would be much appreciated!

  You have McAfee? McAfee has been updated at the same time as the last batch of updates from Windows 7 and this is the cause of problems of internet connection for most, if not all, users of McAfee.

  See the communication from this "criticism" - McAfee

  Some customers may experience a loss of network connectivity and/or errors in McAfee Security Center after a recent update

  You should make the fix McAfee, if necessary. There are corresponding communications for their enterprise products.

• Dynadock: displays preferences are stored in the stop/restart only

  Hello fans of Toshiba and experts.

  I have a problem with * Dynadock DVI * and laptop computer from a different manufacture (with Vista Enterprise).

  I want to use this combination to eliminate the need for a typical desktop computer in office (without multimedia applications or 3D) environment, where * external monitor is defined as main display *, and * LCD internal as an extension of office *.
  This work of setting as planned, the main screen moves between external and internal monitor according to the (UN) Dynadock connection. However, this behavior lasts only until the stop/restart is performed. Then, the configuration is completely random. In some cases, it works as before, in other cases, the default mode is applied - internal LCD becomes the main screen and the image is mirrored on external monitor.

  The whole situation seems to depend on computer with the Dynadock is used. I found the laptop (also Vista) running solid rock with Dynadock.
  All used the drivers were in the latest versions - freshly downloaded, Vista Enterprise SP1 version of the Dynadock 2.3 software update.
  Is there a way to force Dynadock software to use the built-in views configuration whenever the docking station is plugged?

  Thank you...
  Petr Kopecek

  It could be a display driver problem, have you updated display driver and the BIOS of the laptop?

• My pointer freezes, so I have to stop & restart for 20% of the time. How can I fix it?

  My pointer freezes, so I have to stop & restart for 20% of the time. How can I fix it?

  Hello

  • When the issue started?

  Method 1:

  Step 1: Check if the problem exists in Mode without failure.

  See the article below for Safe Mode steps in Windows XP.

  A description of the options to start in Windows XP Mode: http://support.microsoft.com/kb/315222

  Step 2: If the problem does not persist in Mode without failure, then try to clean boot.  You need to perform a clean boot to find the program that is causing and then disable or remove.

  How to configure Windows XP to start in a "clean boot" State: http://support.microsoft.com/kb/310353/en-us

  Note: When you are finished troubleshooting, follow the steps as explained in the article to reset the computer to start as usual.

  Method 2:

  Also check the logs in Event Viewer for the recent activity on your computer and check.

  This article describes how to use Event Viewer to view and manage the event logs in Microsoft Windows XP.

  How to view and manage the event logs in Event Viewer in Windows XP: http://support.microsoft.com/kb/308427

• How to activate the Sleep function to put the computer to sleep if a program is open?

  I have Windows Vista basic on a desktop Dell 530.  I found that if I have a program or application running (such as I-tunes or windows media player) then the Sleep function will not put the computer to sleep.  How to activate the Sleep function to replace these programs and put the computer to sleep?

  Note: This is how it was with windows XP, the Sleep function would put the computer to sleep no matter what was running, he was reliable, if you left the computer and I forgot that you had something running.

  Thanks for your help.

  Hi kevino4130,

  If you disable sharing on your computer (not only the power settings) of media, it should allow him to enter the mode 'sleep'.

  See if that does not solve your problem and let us know.

  Dave D

  Dave D
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think.

• Virus scan Avira would stop working and freeze the computer whenever an analysis was carried out. Tried to uninstall and reinstall, but still had the same problem. Impossible to uninstall now due CCPLG. XML error.

  Hello, I have been using Avira anti-virus on my computer for the past two years with no problems.  I run a scan on my computer every day and noticed problems with it a few days ago.  The analysis would be about 21% when he would stop scanning and freeze my computer.  The RAM would be also be maxed out at 100%, and I need to restart the computer manually.  When I ran the scan in safe mode, it worked fine, but then continued to not work when the computer is not in safe mode.  I would also get a security alert Windows telling me that Windows did not antivirus software on this computer.  I tried to do a system restore which goes back to the day before the problem started to happen with the scan, but I still have the same problem.  I tried to uninstall the program again, but I get the message: Setup could not determine feature control file, or was not able to read it properly the. I also received a message about CCPLG. XML. I don't know what to do at this point or what was wrong in the first place with my antivurus software, but I feel that I continue to do worse with everything I want to do about it.  If you can offer any help with this problem, it would be much appreciated.  I have to go to work now, so I'll check tomorrow and hope that someone decided to go back to me.  Thank you.

  There are similar problems listed in the Forums of Avira.

  Have a read of the info in them; who can help you:

  http://Forum.Avira.com/WBB/index.php?page=thread&ThreadId=77368

  http://Forum.Avira.de/WBB/index.php?page=thread&PostID=729964

  Both above the Avira Forum entries have the same problem, CCPLG. XML, like you with solutions provided.

  http://www.Avira.com/en/support/kbdetails.php?ID=135

  Avira has also a manual uninstall. read the link above.
  Try this: uninstall/reinstall Avira as it

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  If the above does not work:http://www.avira.com/en/support/

  Contact the Avira Support on this problem with their anti-virus software.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

  Also, try asking the security of Vista and the Privacy Forum.

  They know a little about the Avira software there.

  http://social.answers.Microsoft.com/forums/en-us/vistasecurity/threads

  See you soon.

  Mick Murphy - Microsoft partner

• GfxUI.exe has stopped working after rebooting the computer.

  Original title: error GfxUI.exe

  I've been running Vista business for a few years.  Last week, after the reboot, I get an error message that GfxUI.exe has stopped working.  After that I closed the error box, the PC works fine.  I updated the graphic driver Intel, but always the message.  Why now I get the message and how can I solve this problem?

  Hi Kea2300,

  Did you the latest changes on the system?

  This error message indicates to the Intel graphics driver.

  Because you tried to update the Intel graphics card, you can try to perform a clean boot and check if the problem persists.

  A clean boot to check if startup item or services to third-party application is causing this issue.

  You can read the following article to put the computer in a clean boot:

  How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7

  After the troubleshooting steps, please refer to clean the boot link to put the computer to normal startup mode.

  Hope this information is useful.