Show slides on the Cisco SX20
Is there a way to push a computer feed or image for all the other endpoints through a MCU, like slides such as a widescreen and multi point Conference as a small window for all parameters? So on my side if I were to wake up the computer feed with slides instead of the larger image of the Conference, I would like the slides as the big screen and a small window of participants as the right corner.
I wish that this same config to be seen by all the world. And that's the SX20 Cisco.
If you are using an external MCU, then required available must be set to the MCU.
How it appears on the other endpoints depends on their capabilities and how these end points have been set up.
I.e. If an endpoint has been configured with two monitors, then they will normally see the presentation on a display screen / and other participants on the other screen/screen.
/Jens
Please note the answers and score the questions as "answered" as appropriate.
Tags: Cisco Support
Similar Questions
-
Codec for the CISCO SX20 problem
Hi all
I have a system SX20 and its codec seems to never start,
The power LED button flashes slowly,
The Ethernet connection does not work,
There is neither video nor audio, signal
It seems to be in standby mode, but ir never wakes up,
I can't access the web interface,
I also tried to reset by using the power button,
Thanks in advance,
You can try to connect to the SX20 with connection in series (see this thread for some options - 8 Post by Tanja Bader) and see if you are able to see all messages on the console.
Otherwise, it looks like you need to RMA the device.
Wayne
--
Please remember the tor frequency responses and mark your question as answered as appropriate. -
Cannot launch the call to Polycom V700 to Cisco SX20/EX90
Hello
I am configuring a Cisco SX20 and a Polycom V700. I can call to Polycom Cisco, but can't call Polycom to Cisco. It proved a mistake, "your call could not be connected because the call was was routed through a network of intermediary that is not service the remote site." Please contact your network administrator. "But I have that in place inside the LAN, and there is no firewall on the inside.
I've tried with EX90 as well, but it's the same thing.
Can someone please advise me what I missed?
Concerning
Robi
Hi Robi,
I'm kinda a waste, then as to why it does not work... If you have enabled IP H.323 gatekeeper OFF, call preference value IP H.323, numbering method with H.323 Auto in 1st preference and all other disabled protocols - it should just really work when you dial an ip address...
I guess the next thing to look at would be the version of the firmware on the polycom - is recent (or maybe an older buggy)?
In addition, you could try a factory reset on the device (just to make sure there is not another stuck somewhere setting) and to reconfigure settings you need.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate.
-
When I try to use the impromptu slide show I get the message "video support is disabled" how to activate it?
It is a "Bug" in the software, waiting for a fix.
It can be corrected temporarily by open images in the slideshow beforehand module and run the slide show IN THE module.
When you return to the library grid view, the impromptu slideshow (Ctrl + Enter) will work.
-
Is it possible to have the Parallax scrolling and changing slide show? (so the slideshow still looks and looks you scroll your top content once again)
You can apply the opacity to images or defining a key position for slide show as well as with the page highlight opacity changes and will bring similar effect.
Thank you
Sanjit
-
May not know how make a slide in the show have a link in DW
Hi - I am changing an existing Web site, that I inherited from a previous developer who's not here. I'm trying to understand how to add a hyperlink in the cursor, I have inherited from him. I don't know why it did not it easier to add a link to a slide, because many of them now take you somewhere when you're watching a slide show.
In anyway, even if you don't see the slider not live because it is on a private network, I have posted a code here and here is an improvised version of the Web site:
http://designerandpublisher.com/mwelectric/test-mockup.html
This seems to be where you can make a hyperlink for slides:
This 'Exchange' is in fact the buttons so I tried to add links to the above "href" and they did not work and I don't want to make the little buttons in the way of a story of some sort (see below):
I want to do is just make headlines for each slide of the hyperlink. I tried to do this:
by changing the class to access the descriptions which is in the CSS and then I added the text of the slide in the ref hoping that would work but he completely bumble. So I hope that someone can help me. Thank you.
Caveat: I'm just stumbling around here. I tend to Occam's razor kind of reasoning
(The simplest explanation is usually the right one).
So I just added the link in the source code of your test page
http://www.Google.com">https://dev3.orr.noaa.gov/sites/all/themes/bluez/images/slideshow/slide-image-1.jpg" typeof = "foaf:Image" class = "slide-img" >
Using Firebug, the link worked, and hovering over the image displays only the text desired with no display code.
-
Create a slide show and change the image by clicking on it? (!)
How can I create a slide show and change the images by clicking on them?
here you can find an example: http://www.thisiscatalogue.co.UK/around-the-way/
Thank you!
solved
-
Slide show - Advance to the next slide on mouse click
I'm new on first so I was wondering if in a slide show, you can move the slide to the slide by clicking the mouse.
Our units have up to 40 slides each and we also have video clips between some of them and we need to maually move the slide to the slide so that educators have the time for discussion on each.
Thank you
Mark
You will need to use a program dedicated for it, as a Powerpoint slide show. PrPro is a video program only and will not create slideshows that allow user interaction, away from hit a pause button over and over again... Sorry!
-
* An audio legend attached to a photo is not imported in a slide show, even if the option include Audio legends as Narration is selected.
Is this always true? The problem has been fixed? I just tried and it does not work for me.
With the help of Photoshop elements slideshow, Windows XP
Sorry, I can't be a great help in this regard - maybe someone else can help.
-
xhistory Cisco SX20 codec calllog
Hi all
Can someone help me? I have a Cisco SX20 with the version of the TC7.2.1 software, I´d as know, if a limitation extracting SX20 call logs using the command line:
xhistory calllog appeal
I extracted the last 30 days, always, once the month.
TKS,
Caesar
You may have been able to see some newspapers, but this is not a complete list of all calls (at least that you didn't really use the unit much at all).
With TC7.2.1, you can retrieve the call history via the web interface in a more readable format (Diagnostics, historical calls) - but to have a glance at it, it shows only the last 100 calls (which, for the unit, I looked it is a matter of days, not the "last 30 days" you are after).
You really need TMS to capture and save the CDRs to be able to report for any significant period of time. You can download TMS and run as a demo version to report up to 3 devices without any permit.
Wayne
--
Remember the frequency responses and mark your question as answered as appropriate. -
HP Touchpad browser works only with the Cisco Valet Plus router
I bought a 16 GB HP Touchpad several months ago and had been enjoying his excellent WiFi feature with my old G from Linksys WRT54GS wireless router until I replaced it with a new Cisco Valet Plus (model M20) wireless-N Router a couple of days.
Although I could easily and successfully, join the Touchpad to the Cisco Valet network, browser fails most of the time to load web pages. For example, if I go to www.yahoo.com, the browser is going to slowly load the web page, or it will expire with a pop-up message error "Impossible to load the Page. If I try to select a link from the homepage of Yahoo, it expires with the same message. And this happens for all web pages. If the initial page happens at all, I can then from this page a link to any other.
I know that the issue is not with the router because I have several other devices connected to it and they are all working well, including a laptop HP ProBook, an iPad and a Wii Console, I use to watch Netflix movies on. None of them has a problem - only the Touchpad.
If I go into settings-> Wi - Fi, it shows that the Touchpad is connected to Cisco network. And when I run the diagnostic system, it shows that the Wi - Fi works correctly.
Does anyone have an idea how to solve this problem?
I have found a workaround that did the trick. I had to change the channel setting auto on a coded hard 1 channel wireless.
Now, the Touchpad works very well, as well as all other devices that have worked.
-
Including the Cisco works views in Foglight dashboards
Hi all
Is it possible for me to view the CISO Layer2 topology works seen in foglight?
I can get the views of the Url in function but the views of application Java with the network topology im stuggling to show.
Concerning
CM
Ive attached the Cisco view I want to include in a dashboard Foglight
Thanks for adding the image.
Are these opinions presented with a rich GUI or is there an http address that we can access?
I suspect I know the answer you said "I can get the views of the Url in function but the views of application Java with the network topology stuggling to show im.» but I just want to be 100% sure.
I want to check that it is not (or is), something that can be added with an iframe
http://eDOCS.quest.com/Foglight/567/files/WCF-ref/docs/component/WCF/IFRAME/
http://en.community.Dell.com/TechCenter/networking/NMS/m/mediagallery/20439075
http://communities.quest.com/docs/doc-7956
Golan
-
Problem starting the Cisco 2821 router
Hello world
I have cisco 2821 router. I am facing problem starting.
someone suggest me what is the problem.
Thanks in advance...
VERSION of the SOFTWARE system Bootstrap, Version 12.4 (13r) T, (fc1)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 2006 by cisco Systems, Inc.The ECC memory initialization
.
C2821 platform of 262144 KB of main memory
Main memory is configured for 64-bit with ECC activeReadOnly initialized ROMMON
load complete, point of entry to the program: 0x8000f000, size: 0xcb80
load complete, point of entry to the program: 0x8000f000, size: 0xcb80load complete, point of entry to the program: 0x8000f000, size: 0x26bc2cc
Decompression of self-image: #.
################################################################################
################################################################################
################################################################################
################################################################################
################################################################# [OK]Smart init is enabled
Smart init is sizing iomem
MEMORY_REQ TYPE ID
0003E8 0X003DA000 C2821 Mainboard
1A 0X0025178C E3 0001AB
0X00263F50 VPN on board
0X000021B8 embedded USB
Swimming pools public buffer 0X002C29F0
Swimming pools public particle 0 X 00211000
TOTAL: 0X00D65284If all memory conditions above are
"UNKNOWN", you could use a non supported
configuration or there is a software problem and
the system may be compromised.
Rounded IOMEM to: 14 MB.
Using iomem of 5 percent. [14 mb / 256Mb]Legend restricted rights
Use, duplication, or disclosure by the Government is
subject to such restrictions as set out in paragraph
(c) Commercial - limited computer software
The rights to FAR clause 52.227 - 19 and subparagraph s
(c) (1) (ii) rights to technical and computer data
Clause of DFARS 252.227 - 7013 section software.Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706Cisco IOS software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 T7 (9)
Version of the SOFTWARE (fc3)
Technical support: http://www.cisco.com/techsupport
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Last updated Friday, January 10 08 16:35 by prod_rel_team
Image text-base: 0x400B1E74 database: 0x434A9AC0ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIR0 = r1 = r2 FFFFFFFF FFFFFFFF = 0 r3 = 45 80000 r4 = 0
R5 = 303 r6 = 0 A7 = 1 = 0 = 100000 r9 r8
R10 = 0 r11 = 465E4369 r12 = 0 r13 = 465E436A r14 = 0
R15 = r16 r17 8 = 0 = C100 r18 = 0 r19 3400 101 =
R20 = r21 0 = 40096828 r22 = FFFFFFFF r23 = r24 FFFF00FF = 0
R25 = 469AAC64 r26 = 0 = 469AAC60 r28 = 0 = 469AAC5C r29, r27
R30 = 0 r31 = 469AAC58 r32 = r33 FFFFFFFF = r34 = FFFFFFFF FFFFFFFF
R35 = r36 = r37 = r38 = r39 FFFFFFFF FFFFFFFF FFFFFFFF FFFFFFFF = FFFFFFFF
R40 = FFFFFFFF = FFFFFFFF = FFFFFFFF = FFFFFFFF r44 r43 r42 r41 = FFFFFFFF
R45 = r46 = r47 = r48 FFFFFFFF FFFFFFFF FFFFFFFF = r49 0 = 469AACD0
R50 = 0 0 = 0 r53 r51 = r52 = 3040A 801 r54 = FFFFFFFF
R55, r56 = FFFFFFFF = FFFFFFFF r58 r57 A000F000 = = 0 = 465E4358 r59
R60 = r61 = r62 FFFFFFFF FFFFFFFF = r63 = 0 402E4B10
GENS = 3400 103 mdlo_hi = my 0 = 251 00
mdhi_hi = 0 = 0 badvaddr_hi = FFFFFFFF mdhi
BadVAddr = cause = epc_hi 0 = FFFFFFFF FFFFFFFF
EPC = 402E4B08 err_epc_hi = err_epc FFFFFFFF = FFFFFFFFERR-1-FATAL %: interruption of the fatal error, reload
err_stat = 0 x 0= Posts from Flushing (02: 37:51 UTC Wednesday, may 18, 2016) =.
Messages in queue:
02:37:51 UTC Wednesday, may 18, 2016: interrupt exception, signal CPU 22, PC = 0 x 0
--------------------------------------------------------------------
Software fault possible. On reccurence, you perceive
crashinfo, 'show tech' and contact Cisco Technical Support.
---------------------------------------------------------------------Trace =
$0: 00000000, AT: 00000000, v0: 00000000, v1: 00000000
A0: 00000000, a1: 00000000, a2: 00000000, a3: 00000000
T0: 00000000, t1: 00000000, t2: 00000000, t3: 00000000
T4: 00000000, t5: 00000000, t6: 00000000, t7: 00000000
s0: 00000000, s1: 00000000, s2: 00000000, s3: 00000000
S4: 00000000, s5: 00000000, s6: 00000000, s7: 00000000
T8: 00000000, t9: 00000000, k0: 00000000, k1: 00000000
GP: 00000000, sp: 00000000, s8: 00000000, ra: 00000000
EPC: 00000000, ErrorEPC: 00000000, GENS: 00000000
MY: 00000000, MDHI: 00000000, BadVaddr: 00000000
CacheErr: 00000000, DErrAddr0: 00000000, DErrAddr1: 00000000
DATA_START: 0X434A9AC0
Cause 00000000 (Code 0 x 0): Exception of interruptionWriting crashinfo in flash: crashinfo_20160518-023752
No reboot to warm storage
System received a system error *.
signal = 0 x 16, code = 0x0, context = 0 x 46905718
PC = 0x40096d7c, Cause = 0 x 20, State Reg = 0 x 34008002Software Cisco IOS, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4 (9)T7
Version of the SOFTWARE (fc3)OK, the router is running on a train of "T".
ERROR detected on Bus PCI1
Try REINSTALLING all the modules in the system
pci1_int_cause 0 x 00000240,
pci1_err_addr 0 x 00091009, pci0_err_cmd 0x0000000A
PCI Master Read parity error
Abort target PCIRemove any all NM/NME or WIC/HWIC cards and restart again. If the router is able to start properly, upgrade the router to a higher version. DO NOT use another "T" train if it is needed. Use instead a train of "M".
-
has the bar at the bottom of the screen from left to right: the Start button, usually several icons quick lauch, notifications of State, date and time, and last BUT NOT LEAST has RECTANGLULAR BOX "SHOW DESKTOP".
I always automatically move the slider at the bottom right of the screen so that it is not in the way and I know where he is.
However, microsft has decided to put a 'show desktop' button in their windows 7 OS at this place.
I DON'T WANT TO SHOW THE DESKTOP WHEN I FIND THE MOUSE HERE.
HOW to REMOVE or disable THIS KEY SO THE PAGE that I READ DOES'NT DISAPPEAR?
Thank you
You can right click an empty area of the taskbar at the bottom of the screen, click Properties and then on the tab taskbar, properties, uncheck "Use Aero Peek to preview the desktop" after you do this, the rectangular box will always be there and you can click it to show the desktop, but it will appear with the mouse just sit there.
-
Correct configuration of the Cisco Access Point 1242AG
Hi all
Here's the situation:
Recently, we decided to create a small network of WLAN in our company. We choose the Cisco AIR-AP1242AG-E-K9 with 2x2.4GHz 2.2dbi rotating dipole antenna.
For better management, a new VLAN routable (ID:20) added to our router IP 192.168.55.1 and SNET 255.255.255.0
Then, I made the following configurations in the autonomous AP through WEB Console:
- Static IP:192.20.10.35, SNET:255.255.254.0, GWY:192.20.10.200
- Vlan1 (native) and VLAN20 (Radio0 - 802.11 g) added in Services.
- I put the encryption against zero for VLAN1 Mode and cipher AES-CCMP for VLAN20
- In Server Manager, I've defined a new 192.20.10.35 RADIUS server (AP-IP) and a secret shared and left the default ports for authentication and accounting (1645 and 1646). Also, in the default server priorities section I put focused 1 time for authentication EAP and the IP (Radius Server) 192.20.10.35 Access Point MAC.
- During the General local RADIUS server configuration, I add as a server for access to the network current (AAA client) the same IP address and the shared secret as the ones I use during the configuration of the RADIUS server above. In authentication protocols enable I left checked only the JUMP and the Mac. In addition, in the users individual section 2 new users created with passwords.
- In the SSID Manager a new hidden SSID created for interface Radio0 - 802.11 g, associated with VLAN20 and in the Client authentication settings section, I left as accepted authentication open with MAC and EAP authentication method. Also, I left the option to use by default for EAP and MAC authentication servers in Server priorities Section and finally I choose mandatory for key management in the section Client authenticated and active the option enable WPA key management.
I can ping VLAN20 IPs from any PC which is a member of the VLAN native both AP
As wireless clients, I use 2 Motorola MC5574 with Windows Mobile 6.1 professional. Both of them have a WLAN Jedi adapter that is configured with the following:
IPs:192.168.55.10 and 192.168.55.11
SNET:255.255.255.0
GWY:192.168.55.1
In addition, a unique profile has been created on all of them to use for the authentication of the association AP. Each profile has been configured for WPA2-Enterprise with AES and LEAP and identification information predefined user (those defined in the PA for individual users)
The problem:
Association of clients with AP is always successful but, authentication fails, and I can't ping the AP IP, IP VLAN20, nor the other customers.
What I'm missing here? I'm sure it's quite simple somenthing but although I tried several different configurations (even WPA - PSK, WPA2-PSK with TKIP) I always find myself without an appropriate solution to unable to ping.
Thanks in advance for any help
Hello
Can you please paste the show run out of AP?
Kind regards
Madhuri
Maybe you are looking for
-
How to fix Adobe Shockwave Flash crashes in Firefox?
BP-401db406-5bf3-437C-9b97-d0b972140627 Hi, this is the last report of the accident I have, it happened a few minutes ago. I've tried usig Firefox in safe mode but nothing seems to solve the problem. Can someone help me please? BTW, keep in mind that
-
iOS9.3 is in place, but the activation service is down
After the iOS 9.3 installed on my 5s, it reboot and ask me to active using my AppleId. Can I enter the ID and password, but it proved to be failed because the apple service is currently unavailable...
-
Tecra S1 video output does not work
HelloI tried to connect my TS1 via cinch to a video projector. Unfortunately due to other reasons I can't use VGA.However I get no signal at all. I almost tried everything. I installed Windows XP with the Toshiba Recovery CD again, but it does not wo
-
Upgrade to a larger disk - compaq presario FR429AA
I have a compaq presario FR429AA and the Device Manager in Windows 7 tellsme, I have a WDC WD32 00AAJS-65B4A SCSI Disk Device as my hard drive is internal. It comes to 320Gig, but I want to put in an internal 2 drive 3 TB to run as the main drive wit
-
I can not connect my HP photosmart 8700 printer to my new computer pro 64-bit Windows. The printer is connected via Ethernet USB not. It seems that there is no 64-bit driver available. What should I do next?