signal does not

Similar Questions

• Radio signal does not, but the switch is on.

  I use a Toshiba Qosmio x 305-windows vista 64-bit. My wireless router has been working well for a few months, since I got it. My radio signal light is not the same if my switch is set to position it. I'm in the Pro Intel/Wireless Tools and run the Diagnostics and it says that the radio signal failed. I tried to disable the network card and reactivating it, but that does not work either. Don't know what to do next. Please help, thanks

  Hello

  Maybe this can help.

  Check the Device Manager for the wireless card valid entry.

  http://www.ezlan.NET/Win7/net_dm.jpg

  If there is no valid entry, remove any entry from fake and re - install the drivers for the wireless card.

  Check network connections to make sure that you have a network icon/entry wireless connection, and that the properties of the icon (right-click on the icon) are correctly configured with the TCP/IPv4 protocol in the properties of network connections.

  http://www.ezlan.NET/Win7/net_connection_tcp.jpg

  Make sure that if there is Wireless Utility a utility vendor is not running with the native Windows wireless utility.

  Make sure you firewall No. preventing / blocks wireless components to join the network.

  Above everything is OK and it connects to the wireless router. Log in from any computer which is, or can be connected to the router with a wire wireless, disable wireless security, make sure that the wireless streaming is enabled and try to connect with no. wireless security.

  When the work turns on the Wireless security.

  Note * people sometimes make mistakes in writing and retype the password for security.

  Another way is to copy in the menu of the router and then paste it when asked of the wireless card.

  --------------------------------------------------

  I really checked and configured every thing and it doesn't work.

  Software firewall application that is not configured to allow local traffic (between the computer and the router is also a possible problem.
  some 3rd party software firewall continue to block the same aspects it traffic Local, they are turned Off (disabled). If possible, configure the firewall correctly or completely uninstall to allow a clean flow of local network traffic. If the 3rd party software is uninstalled, or disables, make sure Windows native firewall is active .

  
  

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• NotificationGlobalSettings modeChanged signal does not work after restarting

  Hello

  I test this on the OS SDK 10.2.1.1927 for my Alpha of Dev C. My application is headless without long-term stop. The signal and slot work perfectly upon deployment of app on device. My slot is called as soon as there are changes to the Notification Mode of the phone.

  But once the restart of the device, for some reason any. Housing starts running headless, the signal and slot is CONNECTED, because I use the bool to check if the connection is successful. And yes it returned true for the connection.

  But in fact, my slot is not called at all. All changes may not be received. Someone at - it get the same question?

  OK, get it fixed. I don't know if BlackBerry will fix this in the operating system or not, but in case you need, then the another work-around is to delay the connection.

  Delaying the call connect to connect this signal modeChanged (bb:latform::NotificationMode:Type) to your site that handles things when the overall Notification Mode is changed.

  In my case, I tested with a delay of 3 seconds and it does not work properly. After the device restarts, it still works properly.

• HDR5010KB-digital recorder - signal does not always come through the use of HDMI

  Hello

  I bought the product above in October. Since then, I have had intermittent problems. When switching on the channel AV on my TV (a Panasonic TX-P42S20B) signal is not always crossed when you use the HDMI channel (I also connected via a SCART, and who works so always seems to be a problem HDMI.) It is particularly obvious when the recorder has been used for a while (be it for recording or playback.) It is not overheating (or if this is the case, not to the degree I get a warning message) and turn off the power to the electric network seems to correct the problem, but it's a pain.

  I tried to change the hdmi cable, as well as to try different channels AV on my TV and it did not help. Is this a common problem or make me a defective unit?

  Any suggestion would be appreciated

  Have you noticed the same problem using other devices connected to your TV (using the same cable)?

• Edge of blackBerry Smartphones and UMA signal does not

  Over the few weeks I noticed that my phone is stuck on the GPRS network all the time and find EDGE or UMA - I can find my house through the wireless section hub but can not connect to it - sometimes with the connection completed and now in the last days that I can not connect via my browser , but all my emails and sms work perfectly - have returned my phone service books, but with no success.

  Please help as I love my blackberry and feel lost without her, when she does not correctly.

  Hi and welcome to the Forums!

  Whenever random strange behaviors creep, the first thing to do is a battery pop reboot. With power ON, remove the hood back and remove the battery. Wait a minute, then replace the battery and cover. Power on and wait patiently through the long reboot - about 5 minutes. See if things return to functioning. Like all computing devices, BB suffers from memory leaks and others... with a hard reboot is the best remedy.

  Best!

• Import of lvm to express signal does not lead to consistent data set

  When you import a file of lvm captured in a VI, SignalExpress visualizes as dozens of data points separated rather than a set of waveform data. Anyone know if there is a problem with the way I am that capture/storage of the data, or is - what a questions at the end of SignalExpress with handling data? One of the files of lvm header is shown below:

  LabVIEW measurement
  Writer_Version 2
  Reader_Version 1
  Tab splitter
  Decimal_Separator.
  No. Multi_Headings
  X_Columns one
  Time_Pref Relative

  Thank you

  Andy

  p.s. that's using LabVIEW 8.6 and SignalExpress 3.0

  Hi Andy,.

  I opened file lvm in Signal Express and saw the same thing you knew. I had a look in the file in the header properties and noticed that the number of samples has been set to 1. I've changed that to 1276 like you who have many data points and they are all now showing on one data set. So, it seems that is trying to create a set of data for each data item in the file lvm. Try changing the number of samples in 1276 and let me know if this is the correct waveform, you need to see.

  Kind regards

  Jas.W

• The music does not open even when no signal.

  I have a spotty cell service where I live. When at work and I am in one of these areas of service not, my music even will not open. I saved music to play offline, but the screen is not yet open. (If I'm in a 'dead zone') no cell signal) does not even open the music.  It searches only. I can't open until I again service.

  Really? Argh! It will be a nightmare when I travel through the mountains of Colorado.  Looks like I'll be getting my Nano out of retirement.

• DMA2200 on PC-monitor does not work?

  Hello

  Well I have except the fact that the DMA2200 support not the VOB files, that the dvd drive is not region free and I had to reverse the mistakes of codes avi using the FourCC change codec, I'm surprised that I'm not able to see anything on a standard PC monitor.

  At first, I plugged the Componet video output (Y, Pb, Pr) of my DMA2200 directly on the vga input of the monitor (Dell 1900FP) with a cable special nine, but I saw just nothing more than a black screen. I changed the monitor for a LG Flatron L222WS monitor told me that the frequency was out of reach... Certain signals does not cross?

  But as the DMA2200 has a HDMI output that welland the Dell1900FP supports DVI - D Dual Link entry too, I. The 1900FP has a resolution of 1280 x 1024 and it can be run up to 75 Hz, 60 Hz it's native refresh rate. So, I went back to the store and bought a HDMI<->DIV - D Single Link cable.

  Only one? Yes, why not!

  DVI dual link as its name suggests has drivers more than the single link DVI for signal transmission. Single link DVI supports a maximum bandwidth of 165 MHz (1920 x 1080 at 60 Hz, 1280 x 1024 at 85 Hz) and use 12 of the 24 pins available. Dual link DVI uses all 24 pins available and supports a maximum bandwidth 2 x 165 MHz (2048 x 1536 at 60 Hz, 1920 x 1080 at 85 Hz).

  So, I plugged the HDMI<->DVI - D on the DMA2200, the Dell1900FP monitor and the monitor directly on channel 2: digital input. But... a black screen again. As I left the monitor rescanning the entrance, he tells me "Please press any key of the mouse button. It seems that the monitor sees a digital signal, but expected more... hmm... what to do?

  I tried to use NTSC (instead of our PAL) on the DMA2200 menu as the frequency changes, but it does not work. I also used all of the selections of entry on the DMA2200-menu (like composite-sd and hd). Normally, the HDMI options is grayed out and uses the default Auto option; but in composite-hd, my old TV mode (connected by SCART) turns black, but can still use the menu on the screen before the DMA and am able to change the HDMI settings, like 480 720 (if I remember correctly) and 1080 p (progressive format) and 1080i (interlaced). I hoped a solution here, but maybe it's just not my day.

  Then.

  Y at - there anyone out there that can help me to get a picture on the monitor? Whether vga or dvi - d... Please...

  Your Dell LCD and DMA2200 not being able to understand/sync between them with a direct DVI connection you could try to put a device inbetween them so that your Setup program can work. Try this device, basically, you connect the DMA2200 using RCA cables to the KWorld device and this KWorld device is then connected to your Dell LCD screen.

  See you soon.

• After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices &amp; their very good WiFi signals. Please help me solve this terrible problem...

  After updating my iPhone 6 (9.3.4) the WiFi signal becomes very low! I did everything, but the problem does not stop! I don't a not update my other devices & their very good WiFi signals. Please help me solve this terrible problem...

  Here's a tip for the user on the problems of Wi - Fi. Suggest from the top and bottom. Maybe one of them will help you.

  (1) restart you device.

  (2) resetting the network settings: settings > general > reset > reset network settings. Join the network again.

  (3) reboot router/Modem: unplug power for 2 minutes and reconnect. Update the Firmware on the router (support Web site of the manufacturer for a new FW check). Also try different bands (2.4 GHz and 5 GHz) and different bandwidths (recommended for 2.4 to 20 MHz bandwidth). Channels 1, 6 or 11 are recommended for 2.4 band.

  (4) change of Google DNS: settings > Wi - Fi > click the network, delete all the numbers under DNS and enter 8.8.8.8 or otherwise 8.8.4.4

  (5) disable the prioritization of device on the router if this feature is available. Also turn off all apps to VPN and retest the Wi - Fi.

  (6) determine if other wireless network devices work well (other iOS devices, Mac, PC).

  (7) try the device on another network, i.e., neighbors, the public coffee house, etc.

  (8) backup and restore the device using iTunes. Try to restore as New first and test it. If ok try to restore the backup (the backup may be corrupted).

  https://support.Apple.com/en-us/HT201252

  (9) go to the Apple store for the evaluation of the material. The Wi - Fi chip or the antenna could be faulty.

  Council: https://discussions.apple.com/docs/DOC-9892

• HP monitor does not display "DVi signal.

  My HP LP2275w monitor does not display "DVI signal" when connected with a DVI cable (supplied), but when it is connected via a VGA cable and adapter DVI/VGA (both supplied) it works but no BIOS screen. It begins immediately with the logo of the VICTORY.

  I just bought new HP Pavilion 500-158eg, Intel Core i5-4440, with AMD Radeon HD8570, 2GB processor, running on WIN7 Pro 64 b. VGA and another port of the motherboard are initially blocked so I can connect the monitor only via the output HDMI or DVI on the graphics card.

  I should note that on my old machine without a name with the graphic upgrade ATI Radeon, there is no problem and I used the same cable. There was an electric shock that causes the collapse of the motherboard so I can't even re - check on the old machine. I can't verify if there is a problem with the DVI cable because all laptops in our housing have only the VGA output...

  All solutions?

  Concerning

  Disco96, welcome to the forum.

  The specifications for the computer show that they run win 8 64-bit.  Downgrade you for Win 7?

  Here's what the quick reference Guide shows for the monitor:

  Model: (LP2275w) product #: video (KE289A4) standard: (WSXGA +) Native resolution: Aspect ratio (1680 x 1050): (16:10) types of connectors: (DVI - I, (support HDCP) DP) cable/s included: (DVI - D to DVI - D, DVI - I VGA, DP USB,)

  Also, here are the i/o ports of back on the computer:

  Figure 2: Rear i/o ports

• WIFI and Signal are Orange, Google game does not load

  Hello

  Last week I had various problems with my phone (Moto G, Android 4.4.4, bought new AT & t in may 2015) and I don't know if they are related. Here are the symptoms that I noticed:

  • Battery drains faster than usual when not in service (during the night).
  
  
  
  • Play Google Services does not (so I can't update).
  
  
  
  • WIFI and cellular Signal icons are the two Orange all the time (even after the ignition and the device).
  
  
  
  • Texts are reluctant to send, and some other applications are difficult to load.
  
  
  
  • Lock screen does not always work as before.
  
  
  
  • There are other various small bugs that appear now also, but none that affect significant my use of the phone.

  Here are some of the things I've tried:

  • Turning and the phone.
  
  
  
  • Turning and WIFI.
  
  
  
  • Turning and Mobile Data.
  
  
  
  • Empty the cache to game Google and other applications.

  Normally with this many questions I would like to replace the device and not buy from this manufacturer again for several years, but this time I have a payment plan with AT & T and still have $80. Am I out of luck?

  Thanks for your help.

  I did a Factory Data Reset and everything is corrected now.

• DAQ signal accessory 50 pins i/o does not

  Why is the 50 IO pins in my DAQ 6014 does not? Please help guys

  When I use the analog channels available on my signal accessory, it works. However, if I use the analog channels on the MIO 50 pins, it doesn't quite work.

  I need to activate it or what?

  You don't make much sense. 50 pin connectors are used to connect a DAQ 50 equipment pins. You should really use something like the map of derivation of the scb-68.

• Example of arbitrary signals fgen does not

  Hello

  I use an example of NOR-FGEN - "any arbitrary signals." I want to activate the digital filter, but there is an error occurred. What should I do to fix this error?

  bahec666,

  The SMU-5451 does not support a digital filtering.  That's why you get the error message that you are experiencing.

• Time scale does not properly after separation of the two signals of virtual channel

  Hi all

  I have a problem when I use a virtual channel with two analog inputs. I'm cutting the two signals into two separate tables of waveform, as shown in the attachment. The two signals seem to be reading very well, the problem is that the time scale (x-axis) begins to act on the strange. Seconds displayed time seems to keep jumping up and down at a high frequency, resulting in the two signals of displayed does not correctly in the table of waveform. Could someone please try to help me? Any help would be greatly appreciated!

  Thanks in advance.

  Try to acquire a signal with first time information. You can replace the DBL 2D with a data type of 1 d wave. You don't need this code extra silly - just a function of Board Index to get the separate channels.

• My office does not send signal to monitor

  HP Pavilion a6200t and Desktop HP vp17 monitor

  My office does not send signal to monitor. I use the monitor to another computer it works fine.

  Problem 3 months ago.
  I clean the inside of the desktop with the compressed air bottle.

  Very important, I clean the contacts of the RAM with a cloth of cotton soaked in 95% alcohol.