Site configuration VPN Multi site.
I currently can do a site VPN between two routers, but I need a little help on how to add another site to the config. Sites remote only need to talk to the router base so I shouldn't need free WILL, but I'm not sure what is the right way to add additional hosts. It seems that I can only add a card encryption to a physical interface so, how do you add the other site?
It's all the orders I have run to get the top of the site to another and going to what else do I need to add? Sorry to be a newb.
Router (config) #crypto isakmp policy 9
Router (config-isakmp) #hash sha
Router (config-isakmp) #authentication pre action
Router (config) #crypto isakmp key address
Router (config) #crypto ipsec - the association of safety to life seconds 86400 Router (config) #access - list 110 permit ip any one Router (config) #crypto ipsec transform-set esp-3des esp-sha-hmac Test Router (config) #crypto map Test 1 ipsec-isakmp Peer Router (config-crypto-map) #set
Router (config-crypto-map) #set transform-set Test Address of the router (config-crypto-map) #match 110 Router (Config-if) #crypto map Test * \run command on the int of the VPN Hi Chris, You can do it. Source peer ip address is an address that corresponds to your address outside. But you can have several pairs of destination and policies that can be assigned to the same router. http://www.Cisco.com/en/us/Tech/tk583/TK372/technologies_configuration_example09186a008009463b.shtml This document helps you to be better. It's a basic documentation. But this will give you an idea. Please assess whether the information provided is useful. By Knockaert Tags: Cisco Security Please give index on configuring vpn site to site on 881 to ASA 5505 cisco router Earlier my boss asked me to prepare to implement the VPN site-to site on router Cisco 881 Integrated Services to ASA 5505 router, which is now running on the side of HQ. Someone please give me a hint. I am now learning the pdf file from Cisco that mention how to configure VPN site to site between 1812 Cisco IOS router and router of the ASA 5505 using ASDM V6.1 and SDM V2.5. Cannot find the book for the Cisco 881 device. Someone please please suggest me something as soon as POSSIBLE. Thank you CLI version: ASDM and SDM Version: Need help to configure VPN NAT traffic to ip address external pool ASA Hello I need to configure vpn NAT ip address traffic external pool ASA For example. Apart from the ip address is 1.1.1.10 VPN traffic must be nat to 1.1.1.11 If I try to configure policy nat or static nat ASA gives me error "global address of overlap with mask. Please, help me to solve this problem. Thank you best regards &,. Ramanantsoa Thank you, and since you are just 1 IP 1.1.1.11 Polo, the traffic can only be initiated from your site to the remote end. Here is the configuration of NAT: access list nat - vpn ip 192.168.1.0 allow 255.255.255.0 10.0.0.0 255.255.0.0 NAT (inside) 5 access list nat - vpn Overall 5 1.1.1.11 (outside) In addition, the ACL crypto for the tunnel from site to site should be as follows: access-list allow 1.1.1.11 ip host 10.0.0.0 255.255.0.0 Hope that helps. I am interested in establishing a VPN for my computer. I looked at some of the information to help Ms. I'm missing something in the way of understanding how do or end the connection. You can configure VPN regardless of static or dynamic IP, both are possible. You can refer to: LT2P configuration vpn cisco asa with the internet machine windows/mac issue Dear all, I have properly configured configuration vpn L2TP on asa 5510 with 8.0 (4) version of IOS. My internet does not work when I connect using the vpn. Even if I give power of attorney or dns or I remove the proxy It does not work. only the resources behind the firewall, I can access. I use the extended access list I tried also with the standard access list. Please please suggest what error might be. Thank you JV Split for L2TP over IPSec tunnel tunnel is not configured on the head end (ASA), it must be configured on the client itself, in accordance with the following Microsoft article: The router configuration VPN VTI adding a third site/router Hello I currently have two cisco routers configured with a connection to a primary WAN interface and a connection to an Internet interface. I have a VPN configured using a VTI interface as a secondary path if the primary circuit WAN fails. IM also using OSPF as a dynamic routing protocol. Failover works and itineraries are exchanged. The question I have is that if I want to put a third-party router in this configuration I just add another interface tunnel with the tunnel proper Public source and destination IP and new IP addresses for a new tunnel network. Any guidance would be appreciated. Thank you Andy Router1_Configurtation_VTI crypto ISAKMP policy 1 BA 3des preshared authentication Group 2 ISAKMP crypto key Cisco12345 address 0.0.0.0 0.0.0.0 Crypto IPsec transform-set esp-3des esp-sha-hmac T1 Crypto IPsec profile P1 game of transformation-T1 ! interface Tunnel0 IP 10.0.1.1 255.255.255.0 IP ospf mtu - ignore load-interval 30 tunnel source 1.1.1.1 Internet Source * Public 2.2.2.1 tunnel * Public Destination Internet destination ipv4 IPsec tunnel mode profile P1 IPsec tunnel protection ! Router2_Configuration_VTI crypto ISAKMP policy 1 BA 3des preshared authentication Group 2 ISAKMP crypto key Cisco12345 address 0.0.0.0 0.0.0.0 Crypto IPsec transform-set esp-3des esp-sha-hmac T1 Crypto IPsec profile P1 game of transformation-T1 ! interface Tunnel0 10.0.1.2 IP address 255.255.255.0 IP ospf mtu - ignore load-interval 30 2.2.2.1 tunnel source * Source public Internet 1.1.1.1 tunnel * Public Destination Internet destination ipv4 IPsec tunnel mode profile P1 IPsec tunnel protection Since this config is configuration of keys ISAKMP using address 0.0.0.0 0.0.0.0 is not required for a new encryption key isakmp with the new address of the site. Simply configure the VTI on the new router and one or both of the existing routers. One of the aspects of this application that should consider the original poster, that's how they want data to flow when the third-party router is implemented. With both routers, you have just a simple point-to-point connection. When you introduce the third-party router do you want one of the routers to use hub? In this case, the hub router has tunnels each remote Ray. Each remote RADIUS has a tunnel to the hub. Talk about communication talk is possible but will have to go to the hub and then out to the other remote. The other option is a mesh configuration where each router has VTI tunnel to the other router. HTH Rick Configure VPN site to site with CCP Hello I have several VPN site to site of small offices, at Headquarters. Is possible to make a single configuration for all virtual private networks on the "vpn server"(ISR 1801) or I still need to add an entry for each VPN subnet? ". If Yes, is possible with the CCP? Kind regards Nuno You can then configure the VPN using CCP. I prefer the command line, and if there are many VPN from Site to Site, you can have a model, and what's happening to one VPN to another is interesting traffic, the INVESTIGATION period by peers and the pre-shared key. It depends on the policy. Federico. Configuration VPN from Site to Site on two ASA5505 I have two ASA5505 ver 8.4 (6) and ver 9.0 (2) configured for a laboratory site to site vpn, but without success. I could do everything outside address from two ASA ping, but could not ping the LAN on the other end of the ASA. Here is the error message when you try to check if the VPN tunnel is established. For reference, the configurations are provided below. Any help is very appreciated. ASA1 # show crypto isakmp his There are no SAs IKEv1 There are no SAs IKEv2 ASA1 # show crypto ipsec his There is no ipsec security associations ASA1: crypto ISAKMP allow outside the local object of net network subnet 192.168.1.0 255.255.255.0 net remote object network Subnet 192.168.2.0 255.255.255.0 ! outside_1_cryptomap list of allowed ip object local net net access / remote tunnel-group 200.200.200.1 type ipsec-l2l IPSec-attributes tunnel-group 200.200.200.1 pre-shared-key pass1234 ISAKMP retry threshold 10 keepalive 2 ! part of pre authentication isakmp crypto policy 10 crypto ISAKMP policy 10 3des encryption crypto ISAKMP policy 10 sha hash 10 crypto isakmp policy group 2 crypto ISAKMP policy life 10 86400 Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac card crypto outside_map 1 match address outside_1_cryptomap card crypto outside_map 1 set pfs Group1 peer set card crypto outside_map 1 200.200.200.1 card crypto outside_map 1 set of transformation-ESP-3DES-SHA outside_map interface card crypto outside ! NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote output ASA2: crypto ISAKMP allow outside the local object of net network Subnet 192.168.2.0 255.255.255.0 net remote object network subnet 192.168.1.0 255.255.255.0 ! outside_1_cryptomap list of allowed ip object local net net access / remote tunnel-group 100.100.100.1 type ipsec-l2l IPSec-attributes tunnel-group 100.100.100.1 pre-shared-key pass1234 ISAKMP retry threshold 10 keepalive 2 ! part of pre authentication isakmp crypto policy 10 crypto ISAKMP policy 10 3des encryption crypto ISAKMP policy 10 sha hash 10 crypto isakmp policy group 2 crypto ISAKMP policy life 10 86400 Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac card crypto outside_map 1 match address outside_1_cryptomap card crypto outside_map 1 set pfs Group1 peer set card crypto outside_map 1 100.100.100.1 card crypto outside_map 1 set of transformation-ESP-3DES-SHA outside_map interface card crypto outside ! NAT (inside, outside) 1 local static source net net-local destination static remote net net / remote output ASA1 # sh run int ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 IP 192.168.1.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 IP address dhcp setroute ASA1 #. ASA1 # ping 192.168.2.1 Type to abort escape sequence. Send 5, echoes ICMP 100 bytes 192.168.2.1, time-out is 2 seconds: ????? Success rate is 0% (0/5) ASA1 # ping google.com Type to abort escape sequence. Send 5, echoes ICMP 100 bytes to 173.194.46.71, wait time is 2 seconds: !!!!! Success rate is 100 per cent (5/5), round-trip min/avg/max = 12/10/20 ms ASA1 #. ASA2 # sh run int ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 Shutdown ! interface Ethernet0/3 Shutdown ! interface Ethernet0/4 Shutdown ! interface Ethernet0/5 Shutdown ! interface Ethernet0/6 Shutdown ! interface Ethernet0/7 Shutdown ! interface Vlan1
nameif inside security-level 100 IP 192.168.2.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 IP address dhcp setroute ASA2 # ping 192.168.1.1 Type to abort escape sequence. Send 5, echoes ICMP 100 bytes to 192.168.1.1, time-out is 2 seconds: ????? Success rate is 0% (0/5) ! ASA2 # ping google.com Type to abort escape sequence.
Send 5, echoes ICMP 100 bytes to 173.194.46.64, wait time is 2 seconds: !!!!! Success rate is 100 per cent (5/5), round-trip min/avg/max = 14/10/20 ms ASA2 #. If you see any debugs the SAA, there is no encryption of any kind negoiations. The problem may be that you need to generate an interesting to match the ACL traffic. I don't know if you on a physical laboratory or on GNS3. If you use a physical laboratory, attach a laptop computer inside the interface and configure an IP address for this subnet. You may need to do this for the other ASA. Then iniatiate a ping to the other network. Configuration VPN windows server 2012 essencial What policy I need to add in the game until I will configure the VPN in windows server 2012 essential? because when I install the remote access roles I received a message when done that mention me politics. later I activate access and remote access and I can't access the internet, I disable access and remote access to I can connect to internet from my server. There is no forums for Windows Server community. Windows Server forums are on the Technet site. http://social.technet.Microsoft.com/forums/en-us/home?category=WindowsServer ASA5505 for configuration VPN Failover ASA-5510 the best way to configure a second VPN tunnel by another carrier, to fail. The two tunnels would go to the same network a Remote Site. Is it possible to apply a metric or monitor the tunnel so that if the choice we're unavailable two choice would resume. Can you point me to the example configuration preferably with ADSM? Hi Stewart, Please visit this link for the same thing: https://supportforums.Cisco.com/blog/150001 Kind regards Aditya Please evaluate the useful messages and mark the correct answers. Cisco 1921 - how to configure VPN multiple Tunnels to AWS I have a router VPN Cisco 1921. I managed to create tunnel VPN Site to Site with AWS VPN Tunnel 1. AWS offers 2 tunnels, so I created another card Crypto and attaches to the existing policy. But the 2nd tunnel won't come. I don't know what I'm missing... is there a special setup that needs to be done to allow multiple IPsec vpn tunnels on the same physical interface? I have attached a picture and included the configuration of my router, if it helps. C1921 #sh run Current configuration: 2720 bytes ! There should be no second tunnel. I use either a peer or the other, but not both at the same time. To display both at the same time, you need to use the Tunnel interfaces. Amazon would have you sent pretty much the exact commands to copy and paste into. Newbie configuration VPN 5505 for client Win7 I have a client who has an installed 5505. They want VPN with their laptop Win7 but they don't want to shell out $1000 for customer VPN Cisco 10pcs. I have correctly set up the VPN without customer and through a browser, they can get to their files, but they would map network drives is just as if they were in the office. I tried to configure the IP Sec on 5505 and then using the built-in VPN Win7 network connection, but no go. I do also everything through the ASDM, but I know that certain things cannot be done. I prefer to use the ASDM! Anyone else get this set up? 99% of what I see here is how to connect the 5505 for VPN site to site. Thank you! Hello To my knowledge all ASA5505 should have the ability to have 2 VPN SSL connections with the Base license. To my knowledge, this also includes using the AnyConnect SSL VPN Client (which replaces the old VPN IPsec Client software) and the VPN without customer via the Web browser. The AnyConnect VPN Client should be available on the Flash of the ASA and is set when you configure the Client AnyConnect SSL VPN for the first time. On the ASDM, you should be able to configure the client AnyConnect SSL VPN with the "Wizard" as any other type of VPN configuration. The AnyConnect VPN Client is a better choice to use the old client IPsec, especially when it comes to new operating systems. The AnyConnect VPN Client can be installed in the ASA at the users computer when he or she first attempts to connect to the ASA via Web browser and connects with his credentials. -Jouni I am new to the use of Cisco devices and I need a little help with some configurations on an ASA5505 with 8.4. I want to connect 2 ASA5505 with a site-to-site. Site 1 is where I want to connect to. Site 1 we have access to 192.168.40.x and 192.168.42.x networks. This ip is: 192.168.40.254 Site 2 I want to connect to site 1 and see the 40.x and 42.x networks. I am able to connect to the network 40.x and can see devices on it, but I can't go to the 42.x network. This ip device is: 192.168.50.1 The sites are not in the same place, just in case someone asks about it. Hello Seems to me that you do not have good rules configured on Site1 and Site2 ASA on the VPN You must add the following configurations Site1 access extensive list ip 192.168.42.0 inside_nat0_outbound allow 255.255.255.0 192.168.50.0 255.255.255.0 access extensive list ip 192.168.42.0 outside_cryptomap allow 255.255.255.0 192.168.50.0 -It would add both traffic between networks for VPN configurations and unnated traffic through to the remote end Site2 outside_cryptomap to access extended list ip 192.168.50.0 allow 255.255.255.0 192.168.42.0 255.255.255.0 This would add the traffic between networks for VPN configurations Seems that you already have the NAT0 configurations in place for networks, but not above the line for the VPN itself. Please rate if it helped How to configure VPN remote access to use a specific Interface and the road I add a second external connection to an existing system on a 5510 ASA ASA V8.2 with 6.4 AMPS I added the new WAN using another interface (newwan). The intention is to bring more internet traffic on the new road/interface (newwan), but keep our existing VPN using the old interface (outside). I used the ASDM GUI to make changes and most of it works. That is to say. The default route goes via (newwan) Coming out of a VPN using a site to character the way previous (out) as they now have static routes to achieve this. The only problem is that remote incomming VPN access Anyconnect do not work. I put the default static route to use the new interface (newwan) and the default tunnel road be (outside), but that's the point is will not... I can either ping external IP address from an external location. It seems that the external interface doesn't send traffic to the - external interface (or at least that's where I think the problem lies). How can I force responses to remote VPN entering IPS unknown traffic to go back on the external interface? The only change I have to do to make it work again on the external interface is to make the default static route to use external interface. Calling all internet traffic to the (external connection) original Pointers appreciated. William William, As it is right now that you will not use the same interface you have road to terminate remote access unless you know their IP addresses by default. In one of the designs that I saw that we did something like that. (ISP cloud) - edge router - ASA. The edge router, you can make PAT within the interface for incoming traffic on port udp/500 and UDP/4500 (you may need to add exceptions to your L2L static) of the router. It's dirty, I would not say, it is recommended, but apparently it worked. On routers, this kind of situation is easily solved using VRF-lite with crypto. M. Configuration VPN FVS336G V3 FW 4.3.3 - 6: I just bought this firewall and I'm trying to configure a gateway VPN tunnel. I used the VPN Wizard and it worked well. However, when I try to change the 3DES, AES-256 encryption, it works very well for the IKE policy, but when I try to change the VPN policy encryption in the section Auto to AES - 256 policy setting, it says I need to configure some parameters of manual strategy before accepting my change. This seems not correct - I'm not trying to enter manual policy parameters. Is this a bug? JohnRo I reloaded the firmware, restore the default and restored the settings that I saved and VPN policy page seems to work fine now. Thank you! John Using Acrobat Pro XI, Windows 7-64, Firefox 25. If I open a PDF file from a Web site link in Internet Explorer, the PDF file opens and I see the path of the URL where I can copy and send to others. The same link to open in Firefox does not display th 1st generation TC: utility said AirPort disk is a failure Hello I have a prehistoric TimeCapsule running on OS X 10.10.5 and now the usefulness of the airport said that the drive has failed. I know, it's an old device and disk are not lacking, but I wonder why the DiskUtility can't find a mistake. There are I looked in the options but could not find a solution A little problem in Acer E1-422 Hi, I just bought myself an Acer Aspire E1-422, which is overall a great laptop. But I just encountered a problem and any help is appreciated. My old laptop was Acer Aspire 4741, having Win7 OS installed. I used to play with it, but then I realized I HP C4280 all-in-One will not print photos on any HP photo paper HP C4280 all-in-One will not print color or B & W photos on photo paper. Color and B & W photos on plain paper prints. It is used to print normally on all documents. No change, I am aware of cause this malfunction. Any suggestions?Similar Questions
The current configuration of the VTI is below:
Building configuration...
!
! Last configuration change at 02:12:54 UTC Friday, may 6, 2016, by admin
!
version 15.5
horodateurs service debug datetime msec
Log service timestamps datetime msec
encryption password service
!
hostname C1921
!
boot-start-marker
boot-end-marker
!
!
logging buffered 52000
enable secret 5 $1$ jc6L$ uHH55qNhplouO/N5793oW.
!
No aaa new-model
Ethernet lmi this
!
!
!
!
!
!
!
!
!
!
!
!
Research of IP source-interface GigabitEthernet0/1 domain
IP cef
No ipv6 cef
!
Authenticated MultiLink bundle-name Panel
!
!
!
license udi pid CISCO1921/K9 sn FTX1845F03F
!
!
username admin privilege 15 password 7 121A0C041104
paul privilege 0 7 password username 14141B180F0B
!
redundancy
!
!
!
!
!
!
!
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
lifetime 28800
ISAKMP crypto keys secret1 address 52.35.42.787
ISAKMP crypto keys secret2 address 52.36.15.787
!
!
Crypto ipsec transform-set AWS - VPN aes - esp esp-sha-hmac
tunnel mode
!
!
!
map SDM_CMAP_1 1 ipsec-isakmp crypto
Description Tunnel 1 to 52.35.42.787
defined by peer 52.35.42.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
map SDM_CMAP_1 2 ipsec-isakmp crypto
Description 2 to 52.36.15.787 Tunnel
defined by peer 52.36.15.787
game of transformation-AWS-VPN
PFS group2 Set
match address 100
!
!
!
!
!
the Embedded-Service-Engine0/0 interface
no ip address
Shutdown
!
interface GigabitEthernet0/0
Description connection Wan WAN - ETH$
IP address 192.168.1.252 255.255.255.0
automatic duplex
automatic speed
map SDM_CMAP_1 crypto
!
interface GigabitEthernet0/1
Description of the connection to the local network
IP 192.168.0.252 255.255.255.0
automatic duplex
automatic speed
!
IP forward-Protocol ND
!
IP http server
local IP http authentication
no ip http secure server
IP http timeout policy slowed down 60 life 86400 request 10000
!
IP route 0.0.0.0 0.0.0.0 192.168.1.254 permanent
recording of debug trap
host 192.168.0.3 record
host 192.168.0.47 record
!
!
Note access-list 100 permit to AWS Tunnel 1
Access-list 100 CCP_ACL category = 20 note
access-list 100 permit ip 192.168.0.0 0.0.0.255 any what newspaper
Note access-list 101 permit to AWS Tunnel 2
Note access-list 101 category CCP_ACL = 4
access-list 101 permit ip 192.168.0.0 0.0.0.255 any logexit
!
control plan
!
!
alias con exec conf t
SIB exec show int short ip alias
alias exec srb see the race | b
sri alias exec show run int
!
Line con 0
exec-timeout 0 0
Synchronous recording
line to 0
line 2
no activation-character
No exec
preferred no transport
transport output pad rlogin lapb - your MOP v120 udptn ssh telnet
StopBits 1
line vty 0 4
privilege level 15
local connection
transport of entry all
transportation out all
!
Scheduler allocate 20000 1000
!
endMaybe you are looking for
