Sony Vaio black screen...\boot\bcd MSG... e/s unexpected... error status 0xc00000e9

Please help if anyone can?

I have this same error too. II get the screen black, but also says it cannot find an operating system. I can access the bios and reset the defaults. I don't have the recovery disks. DOH! Clues?

Tags: Sony Computers

Similar Questions

  • XP, black screen with the msg of boot errorm insert disc drive system & hit enter, does that mean?

    When you feed on my PC I get a black screen with the "Boot disk error msg; "Medallion system disk & press enter" what does that mean? I don't have the original CD or a recovery disk, what can we do?

    Hello

    This means that your hard disk contains an error, or the start-up phase damaged operating system. If you have any bootable media, you must visit certain computer services near you.

    Maybe just an idea - you have a floppy drive? Maybe you have inserted the floppy in the floppy drive. If the answer is Yes - Remove the floppy disk and restart your computer.

    LC

  • HP Pavilion 15 t-n200: sometimes not found black screen boot device

    Computer during the race will go sometimes to black screen and say "boot device not found", I am able to

    correct the problem by power off, wait a few seconds back, computer power will start

    Save as normal and work very well.  This happens maybe once a week. My fear is of course to some

    time not to come back to the top. Are there corrective measures, should I try now? I have a hybrid

    static hard drive (ST500LM000-1EJ162)...

    .

    Hello @jla11,

    Thank you for visiting the HP Forums! The Forums are a great place where you can find solutions for your problems, with the help of the community!

    I understand that you have a problem with the laptop to a black screen and tried to help you!  I see that you will get the error on the hard disk.

    You might try to test the hard drive for the failure.  In this way, you can check if there are problems.  You can use the following to help:

    Laptops HP - device not found Boot error or hard drive not detected

    You should be able to skip to step 2.  Please post back with the results.

    Please let me know if this information helps you solve the problem by marking this message as 'accept as Solution', this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

    Have a great day!

  • Satellite C650 - stuck with the underscore and black screen boot

    Model: satellite C650

    Operating system: windows 7 Home premium

    Problem: when I try to turn on the computer I see the Toshiba screen and then a black screen with a underscore that blinks several times then stops, and the computer is blocked like that. The fan seems to be working. I can't go to mode without failure or boot options, even if I press f8 or f12 nonstop.

    Last time I started mode, I was stuck on the screen but the connection keyboard touchpad did not work and I couldn't stop. After that I have the strength of closing down and try to restart stuck like that. No beeps or anything like that.

    Any help would be appreciated.
    Thank you

    Good news.
    Thanks for the comments.

  • Changes settings of the BIOS - black screen boot. [TravelMate P453-M]

    Laptop still under warranty.

    I recently had a motherboard and replace the HARD drive.

    I wanted to install Windows Me, but the BIOS has been defined in the UEFI, and I couldn't start on a USB key.

    So I turned on the heritage, booted from the USB and installed Windows very well.

    For some stupid reason, I went back to try to change the setting in the UEFI.

    Now the laptop turns on, but won't start. I get a black screen, no logo or any what guest to access the BIOS.

    I read a little and seems that I have to remove the BIOS battery, let the memory itself to reset the default BIOS settings and try again clear?

    If it's important, I re-installed Windows 7 64 bit.

    Any help would be appreciated!

    Ah, I've solved the problem! Created a boot UEFI active USB key with a GPT partition, using the software of Rufus. And it started from it very well.

    Thank you, my Lord and Savior Google.

  • After reboot, vista with a black screen boot

    Whenever I want to restart my vista family premium after a few updates, it becomes a black screen.i have searched the Internet for a solution, but unfortunately none of them are in my scenario.i still hear the music of vista boot, which I assume that the computer is running but the screen is black.i need help! I would appreciate if I could receive advice on my computer. Computer: NEC P6000

    Hello

    You can access Mode safe? Repeatedly press F8 as you start? If yes you can try Control Panel
    -Double click - Driver tab - click on UPDATE driver - device Manager - map - graph
    then right click on the device and UNINSTALL - REBOOT.

    Another method to try to get to the desktop (try in normal Windows Mode without failure)
    is CTRL + ALT + DEL and the processes tab find EXPLORER.exe and END PROCESS on it.
    then on the tab Applications - lower right - new task - the type in EXPLORER.exe. Safe mode is
    accessible by tapping F8 as you start several times.

    First check this thread in case it is simple and if not to come back to this thread.

    http://social.answers.Microsoft.com/forums/en-us/vistaprograms/thread/50247d5e-0ae0-446c-A1bd-11287fd1478a

    Black screen problems are extremely difficult to repair and all hotfix is usually a hit or miss
    base. That there is no information on a black screen as there is just a blue screen
    adds to the difficulty. Often using a restore point or Startup Repair will have no effect.
    You can try a google to see the proposed repairs, whom some have worked however these
    cover a wide field of efforts.

    Here's a video of one of them.

    http://www.Google.com/search?hl=en&q=black+screen+of+death+Vista&btnG=search&AQ=f&OQ=&AQI=G1

    Here's another fix
    http://blogs.PCMag.com/SecurityWatch/2008/12/the_mysterious_black_screen_of.php

    You have a Vista disk? You can try restoring the system to it. If you do not have the
    discs, your system manufacturer will sell them at low prices. Or try in safe mode if you can get
    it.

    How to make a Vista system restore
    http://www.Vistax64.com/tutorials/76905-System-Restore-how.html

    You can create a recovery disc or use someone even version (to do the system restore
    It only needs to be bootable).

    How to create a Vista recovery disk
    http://www.Vistax64.com/tutorials/141820-create-recovery-disc.html

    ------------------------------------------------

    These require the correct Vista discs since you can not start safe mode.

    Try the Startup Repair tool-

    This tells you how to access the System Recovery Options and/or with a Vista disk
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

    Try recovery options Startup Repair

    How to do a startup repair
    http://www.Vistax64.com/tutorials/91467-startup-repair.html

    -----------------------------------------------

    Here are a few Google searches where many have found different solutions:

    Vista black screen - check that a 1st
    http://www.Google.com/search?hl=en&source=HP&q=Vista+black+screen&AQ=f&OQ=&AQI=G10

    Vista black screen Solution
    http://www.Google.com/search?hl=en&q=Vista+black+screen+solution&AQ=f&OQ=&AQI

    Vista black screen Fix
    http://www.Google.com/search?hl=en&q=Vista+black+screen+fix&AQ=f&OQ=&AQI
    -----------------------------------------------

    If necessary and you can access all ordinary Windows.

    You can try an In-Place Upgrade (hopefully save programs and data) or a repair installation
    (if all goes well, the data records and need to reinstall programs). Don't forget to make a good backup or
    3.

    You can use another DVD that aren't copy protected but you you need to own
    Product key.

    On-site upgrade
    http://vistasupport.MVPs.org/repair_a_vista_installation_using_the_upgrade_option_of_the_vista_dvd.htm

    If nothing works, you can do a repair installation that needs to save the data, but you will
    to reinstall the programs. This also requires correct Vista disks especially for OEM versions.
    You will need to know your product Code.

    This tells you how to access the System Recovery Options and/or a Vista DVD
    http://Windows.Microsoft.com/en-us/Windows-Vista/what-happened-to-the-recovery-console

    How to perform a repair for Vista Installation
    http://www.Vistax64.com/tutorials/88236-repair-install-Vista.html

    ---------------------------------------------------------------------------

    Another method that works sometimes: at the command prompt, type of Vista startup disk:
    (type in a single line or copy / paste a line at a time and then press enter - do not type)
    parenthesis or "BOLD"
    )

    c:

    cd\

    CD c:\Windows\System32\winevt (there is a space between cd and C :)

    Ren LogsOLD Logs (there are spaces between ren and newspapers and Logsold)

    RESTART Windows

    I hope this helps.
    Rob Brown - MS MVP - Windows Desktop Experience: Bike - Mark Twain said it right.

  • Error \boot\bcd 0xc000000f and windows vista recovery status do not work

    Well, I have HP Compaq Presario v3751AU and he could not start today and in \boot\bcd 0xc000000f error.

    I try to put in the recovery disc, it gave me the message "" press any key to start from the CD or DVD. "" When I do this, all that appears is a black screen that says "Windows loading files...". "with a white loading bar in the background, but it is not actually boot from the disc then. the mouse pointer is displayed on the background green-vista, but there is nothing I can click, such as the 'next' button or even the language selection button. He continues to freeze on the vacuum-vista-green background.

    can someone help me?

    Hello

    If you have problems with the process of recovery of manufacturers, contact the manufacturer

    It's their recovery process not microsofts

  • Black screen boot, light works.

    Hi, I have a 2011 end pro 15 "macbook. Two days after leaving a program that my screen went black, the lighting of the screen does not work. Whenever I reboot the screen becomes black. I also tried to reset the NVRAM and SMC memory and installed the new update of el capitan, does not work either. Safe mode works quite 'lag', especially when scrolling in safari, the screen flashes.  Safe mode and recovery mode function, so I did a time machine backup in safe mode and re-installed el Capitan, nothing has changed. I am writing in safari in recovery mode and have no problem. I hope I described the problem enough for someone to recognize.

    I'm running out of ideas and advice of other forums, could someone help?

    That the computer is running in Mode safe, but not after a regular boot gives strongly suggests this is a driver problem. Safe mode starts with the bare minimum of drivers. You say that you have re-installed 10.11 and that you have saved, but you won't go into the details. Did you erase the hard drive, install 10.11, and then use Setup Wizard to restore your applications and data?

    What I would do is run the first Apple Hardware Test. (Reboot, pressing the D key until the test of the system is displayed.) Run the extended test. If it passes, make a final backup of TM and then boot into recovery, wipe the drive, download 10.11 and reinstall. Ordinarily I would run Setup Wizard then, but in this case I would like to make an account - don't use your usual account name - and go to the desktop. Then I shut down the computer and restart. If all goes well after the restart, then I would use Migration Wizard to migrate data and applications. Once completed, restart again.

    At this point, two things is possible: all is well, or the LCD screen is black again. If it is the latter, you know that something in your account of the system is the cause of the problem and we can talk about how to make to recover from that in another message.

  • Help, please! My Duet of 13 sony vaio will not boot from usb

    I deleted the original windows 8 and tried to install 8.1
    But now it't boot not a device external usb?

    There would you remove windows 8? Click assist and try and recover the operating system.

    If it works just follow the following steps to upgrade to windows 8.1 without ruining your vaio

    * Once the computer reinstalls windows 8. Click the help button to open vaio care.

    * Click Vaio Update

    * install every single update, there is until they are all done.

    * return to vaio care, then click Security

    * find where it says windows update and run that.

    (this will update your current version of windows 8)

    * Once it is done go to the microsoft store and the first tile, you should see is

    "upgrading to windows 8.1 for free"

    Download that and your computer will restart running 8.1

    -Specialist Sony from Bestbuy

  • Satellite Pro A300-28V - black screen boot failure

    My three days old Satellite Pro A300 began yesterday to hang at startup in Vista. I rebooted twice with good result, but now I see only the home Toshiba screen, then it goes black with a cursor top left. I won't answer on /F12/ F8 F2 or the recovery of the DVD. Indicator LED disc is black, fan-only sound. I have connected not no matter what external monitor ever on this one.

    At the moment so it's Sunday I chose the battery and will try again in an hour or two, otherwise I contact seller tomorrow. Any ideas what's happening? BIOS crash, hard drive (after three days)?
    / disappointed

    Hello

    Does this mean that you can t access the BIOS too?

    If it s, then it seems to be a hardware problem. Therefore, the service provider authorized in your country. They can help you to repair the laptop.

  • Empty (black) screen boot after Windows updates

    I had this problem on two computers this week... until now. Run windows update after I restart the computer. When the computer reboots, they can start to a blank screen (black). These were not updated video card basis. Also, I tried to use the safe mode, but it crashes on MUP. SYS. I ran chkdsk... and who has not fixed it. Any ideas other then a new installation? Thanks for your help!

    Kevin_C_K,
    You said you ran chkdsk and it didn't fix it, but it will report all the problems?
    If you are still having this problem here is a couple of things to try (if you haven't already done so).
    Run the sfc/scannow utility.
    When you have run chkdsk if you do not use the /r switch, then repeat the it like Chkdsk/r

    After the clean installation, update you all hardware drivers before you start the Windows updates? Mike - Engineer Support Microsoft Answers
    Visit our Microsoft answers feedback Forum and let us know what you think.

  • HP G62 - 340US Black screen on power on, no corresponding led error code

    Hey all,.

    Having a problem with my laptop HP G62-340US. The computer will continue to feed on, but the screen does not light, but the caps lock light has a constant slow continuous flashing. The indicator light next to the charging port is orange, as the light next to the wireless button. (There is no NumLock on the keyboard of a light)

    I looked at the link to HP support for this issue, located here:

    http://support.HP.com/us-en/document/c01443366

    But was unable to find my specific situation. Any help or idea would be greatly appricieated.

    Thank you!

    Try to start the machine without the battery and connected to the power adapter. Try to boot the machine with a single chip memory installed (if you have two). Try changing the location of the chip memory if you don't have one. Do a hard reset by removing the battery, power adapter, pressing the power button for 1 minute, reconnect the battery and power adapter, and then try again. If this does not work, you will have a video chip problem that would require a reflow (I know this isn't your model, but it shows you what may be involved):

    http://www.YouTube.com/watch?feature=player_detailpage & v = bnkQNmKauEc #t = 4S

    Good shops use pistols temperature controlled at worst and stations Infra red reflow for more accurate results.  The video was just to give you an idea what may be wrong.

    http://www.YouTube.com/watch?feature=player_detailpage & v = wEVv7p - JDc #t = 8 S

  • Sony Vaio VGN-FW11M-CD/DVD is damaged or missing error codes 10, 19, 31, 32, 39, 41 problem

    I have now for the past 5months tried to solve this problem, as I have no money to send the machine to Sony for repair, I tried all the tools Mrfix nothing worked it means removing lower the filter and tried to restart computer, many opportunities, I gave up and bought a portable hard drive and although I need my rear disc first of all it is completely fed workstation and even Device Manager for months and nothing has been able to recover it, only yesterday when I turned it on it gave the message that drivers Matashita BD - CMB UJ-120 has successfully installed and I was able to run the DVD, s and I even burned a cd of music just to see if it works and no problem, however I've turned off the laptop and turned it back and am once again to square so that the drive works however if I only install the drivers which I do not know how to access, there is little to soothing sites you can get rivers however all our full of bull & I know that an optical drive comes with the PC , but any ideas or should I just start the fires off the machine just for a good measure and buy a new CD/DVD-rom for the laptop... only another conclusion is that the son or looted, but I do not understand that as I only had the phone for a little over a year and a half gruff the CD/DVD drive would not break so fast?

    Here are the MS tips to solve your problem.

    See if you may have missed a step in their process.

    ·                        http://support.Microsoft.com/kb/982116/en-AU

    Your CD or DVD drive is missing or is not recognized by Windows or other programs

    http://support.Microsoft.com/GP/cd_dvd_drive_problems

    See if the information above solves the problem.

    See you soon.

    Mick Murphy - Microsoft partner

  • Mac mini black screen after upgrading to sierra

    Hello!

    My probleme:Mac Mini end 2014 black screen to start immediately after the upgrade of Sierra.

    Thanks for your help.

    Kentr0n

    Is there anything on the black screen (boot) at all ever?

  • I have service pack 3 installed and yet I still have a black screen with the message of counterfeiting

    I have service pack 3 is installed, but I still have a black screen with the message of counterfeiting. I am a beginner of the computer

    Hello

    (1) you are able to log the desktop computer?

    (2) when exactly you get the black screen?

    (3) you receive an error message on black screen?

    (4) have you made any changes to the computer before the show?

    Please provide more information on the issue so that we can better help you.

    In the meantime, try the methods below and check if the problem persists.

    Method 1:

    In case you receive a black screen on startup of the computer, and then try the steps of troubleshooting provided in the link below.

    Computer stops responding with a black screen when you start Windows XP

    http://support.Microsoft.com/kb/314503

    Method 2:

    If you are able to start the computer and you get the black screen at the level of the office without wallpaper then try the procedure described in the link provided below.

    After the Windows Logo appears or after you log in to Windows, a Windows XP computer cannot display the wallpaper, a black screen or a blue screen

    http://support.Microsoft.com/kb/318027

Maybe you are looking for

  • How can I disable NoScript add on?

    I have downloaded NoScript for one of my Add ons. Now, he gets crosswise put me on Adobe, Acrobat and Java. I would like to remove it. How can I do this?

  • Problem of management of power with the Satellite S2430-402

    Every time is start my laptop, I get a message saying "%1 is not a valid Win 32 application" under the heading "E-power", thus the Toshiba power management does not load. I tried to uninstall and reinstall the software from the cd, but it does not wo

  • Satellite P300 - not more than internet with Vista

    Hello I have a big problem since a few days on my P300 with Vista. I can't connect to the internet. I have not install anything and I don't surf in dangerous sites so I don't understand what that append. I don't know if an automatic release of window

  • HP cm6040MFP Jamming

    Have you noticed with 6040 MFP HP cm machines they hate labels. I tried their execution of all trays paper 5. I replaced all the important driving rollers. Such as: Fuser OEm, Pick up and rolls, secondary power transfer unit. The sheet of labels alwa

  • Why has my Microsoft Security icon disappeared?

    There WAS a Microsoft Security icon. He was green if safe ~ or Orange if there is a risk, and it's at the bottom next to the time. now his party.