SSL error rate high FxM

Similar Questions

• Error rate while having successful data collection

  Hi all

  We follow a request which is to have a collection of data managed but when we checked its error rate, its very high-around 70%. Could anyone suggest me where there might be flaws?

  -Shiva

  Hi Yutiasun,

  We had two different IP configured previously for the same component of the application. When we checked in the list of resources for the Application components, we could see two IP list.

  We have removed the other older, and then the error rate is reduced.

  Kind regards

  Shiva G

• acquisition of data with different sampling rates high

  I have a few questions on the use of the OMB-DAQ-3005 with different sampling rates high.

  For our application, we have 8 analog inputs. Which two are a quick response and should be sampled frequently.  We have an encoder quadrature (CPR 1000 running at 1800 rpm).  We plan to sample X 4 encoder.  For the analog inputs for the quick response, we want to trigger a sample of each pulse or each a few pulses, thus creating a timestamp with the position of the encoder with respect to position index as well as two fast analog inputs.  We have data correlating the analog inputs with the position of the encoder.   Other analog inputs, we want to measure relatively slowly (for example once every 5 dry or similar).

  How can I go on the configuration of the two (or more) sampling rates different wherein I can taste entered at different frequencies?  Also, is there a way to reset the encoder count after outbreak of the index as I have the position of the encoder with respect to the index?

  Maybe you'll find someone here who uses the OMB-DAQ-3005, but this forum is really more designed for LabVIEW programming issues.

  I've never used the OMB-DAQ-3005, but out of curiosity, I took a glance at the Manual of OMB-DAQ-3005.  The answer to both your questions are:

  1. you cannot run a hardware DQA Multiplex (like this one) at independent rates by channel.

  2. the OMB-DAQ-3005 supports an Index Z feature to reset the counter - look for documentation on how to configure any software interface you are using.  If you get stuck, you can try to discover media appropriate for instrument channel.

  Best regards

• Windows mail send any ip ok no error. Ox 800ccc79 cylindrical invalid not port 25 secure SSL error 550 Server

  Windows mail send any ip ok no error. Ox 800ccc79 cylindrical invalid not port 25 secure SSL error 550 Server

  You try to send a file larger than 20 MB.  Try to reduce the size of the attachment of zipping it or go to tools | Accounts | Mail | Properties | Advanced and select the option to break messages apart large.  However, many recipients servers will not accept messages exceeds 10 megabytes, then you could try to send via another method.  BTW, if you attach a file, it must be encoded to be sent by e-mail, and this coding adds about 30-50% the size.

  Steve

• Why the websites of google is the ssl error

  Hello

  My computer is able to use the internet perfectly except when I try and connect to any website of google (google.com, youtube, gmail, etc.), it gives me an ssl error saying

  Unable to connect to the real mail.google.com

  Something is currently interfering with your connection to the site mail.google.com.

  Try to reload this page in a few minutes or after switching to a new network of. If you have recently connected to a Wi - Fi, finish connect before recharging.

  If you visit mail.google.com right now, you could share any private information with an attacker. To protect your privacy, Chrome does not load the page until it can establish a connection to the real mail.google.com.

  At first, I thought it was a browser issue, but it's the same on all my browsers (IE, firefox, chrome). I even tried to disable my firewall, but the problem persisted. Also, it is not a router problem as google sites work fine on all my other devices. I also ran a full sweep of mcafee, and no problems were found. Please help me.

  OK guys I found a solution, if anyone else is having the same problem and that is that my computer time has been bad so now correct the time that google Web sites began to work.

• SSL error after upgrading vSphere

  I upgraded to vCenter Server 4.0.0 today and the following plug-ins do not load when you start the VI - material status vCenter client and vCenter Service status.  The error message in the window manager plugin is "the following error occurred during the download of the plugin script of https://servername:8443/cim-ui/scriptConfig.xml: Impossible to connect to the remote server."  The tab overview of performance also does not work either.  After some searching through the logs I have determined that when the management of Web Services service starts it generating SSL errors.  The newspaper of vpxlicent I see several messages "Validation SSL failed in WebRequestPatch" followed by "no connection could be established because the target machine actively refused it" when it tries to download the scripts for plugins.  In addition, I see it in the tomcat log, catalina.2009 - 07-23, when to start the service of Web services:

  SEVERE: End Point initialization error

  java.io.IOException: could not decrypt entry content secure: javax.crypto.BadPaddingException: given the final block not well padded

  Followed a few seconds later by the present (after much more SSL error messages similar to the one above):

  NEWS: Stop Coyote HTTP/1.1 on http-8443.

  I'm assuming that the last line is the reason why I can not connect on port 8443, and why a netstat doesn't show anything listening on this port on my box of VC.  I know that my certificates of work (up to a certain point) because if I connect via https on port 443 for my box of VC, it works fine.  It is only by trying to connect to 8443 this problem occurs.  I already tried the steps of http://kb.vmware.com/selfservice/microsites/search.do?language=en_US & cmd = displayKC & externalId = 1010641 even if I don't get all messages that point to problems of name resolution and it did not help. 

  Anyone have any ideas?

  I had same problem as described above. In my case, the reason for which the 8443 service did not start is that tomcat was trying to use the wrong password to open the file rui.pfx. I did the following to solve this problem.

  1.) stop windows services on vCenter

  (2.) %PROGRAMFILES%\VMware\Infrastructure\tomcat\conf\server.xml open in Notepad

  3.) search for "< connector port ="8443 ""

  4.), you will see that this line refers to the rui.pfx certificate file that was change when you updated your certificate. Update the 'keystorPass =' for the password of the rui.pfx certificate.

  5.) start the vCenter services

  NOTE: The password cannot be empty for the rui.pfx as it was in my case, because this would cause its failure. I had to import and then export the rui.pfx with a password to get the above to work for me.

  Hope this helps guys.

• Another Question error too high rate data

  Hi all

  I saw a few posts about pgc errors, but most of them deals with slide shows and video not; and I can't find anything with the REF = KApgc error.

  I'm just all my movies on a DVD created, not rocket science.  I use the 'submenu Film' preset with only top 5 movies, things like Easter, birthday, etc.  My transition for each button is a slate (for lack of a better word) which says exactly what it is and when it happened, before each movie plays.

  After I had set everything up, I realized that I didn't have an opportunity to "play all" which would include these slates.  A simple solution, make a 'play together' button that links to a timeline that has everything in it - slate, then the movie, then slate, the next movie and so on.  (When I say movie - they are all .mov files rendered from After Effects, even the slates)

  My transcoding settings are NTSC DV high quality 7 MB VBR 2 pass and the "highest quality" is checked.

  When I run the "check disk" all right.  Listen to samples of the disc, all right.

  Build disk: transcoding hours then the error: data too high to * timecode * REF = KApgc.

  When this film is in itself with a click of a button, it is fine.  It is only in the scenario 'play together' that it produces the error.

  If the flow rate is not too high in one place, why is it too high in another?  It's the same thing, just a longer timetable.

  Help, please!

  Thank you.

  Only a calendar.  But it's just a few clicks away...

  -Jeff

• Illegal transfer of SSL error

  When you use a site Web that I have not had any problems with it, as soon as I click to enter the secure section I get this message:
  An error occurred during a connection to ols2.rta.nsw.gov.au.

  Even SSL rejected a unacceptable content handshake message.

  (Error code: ssl_error_illegal_parameter_alert)

   The page you are trying to view cannot be shown because the authenticity of the received data could not be verified.
   Please contact the web site owners to inform them of this problem. Alternatively, use the command found in the help menu to report this broken site.
  

  I contacted the Organization (to the site) and they did not have any other contact with them on this issue, and so I guess it's a problem with my firefox or security. They reset my account, but it did not help at all.

  Would it because I changed my ISP since the last using this Web site? If so, how can I solve the problem?

  Thanks in advance,

  I had a whole violin after that you're suggesting that something can interfere, such as modules. No luck there, but I just tried to disable NetNanny temporarily and now the Web site work!

  I assume that NN is blocking the site somehow. Not sure if I can fix it, but at least I can use the website occasionally (i.e. how many times I need) by turning off NN for a few minutes.

  A big thank you, Cor - el - I would not have worked it without your patience.

• Writing data to extend the acquisition of data for the sampling rate high file

  These are the tasks that I have to do to take noise measurements:

  (1) take continuous data to USB 6281 Office, in a sample of 500 k (50 k samples at a time) rate.

  (2) save data continuously for 3 to 6 hours in any file (any format is OK but I need to save in a series of files rather than the single file). I want to start writing again file after every 2 min.

  I enclose my VI and pictures of my setup of the task. I can measure and write data to the file continuously for 15 minutes. After that, I see these errors:

  (1) acquisition of equipment can't keep up with the software (something like that, also with a proposal to increase the size of the buffer...)

  (2) memory is full.

  Please help make my VI effective and correct. I suggest to remove him "write in the action file" loop of consumption because it takes a long time to open and close a file in a loop. You can suggest me to open the file outside the loop and write inside the loop. But I want to save my data in the new file, after every 2 min or some samples. If this can be done efficiently without using Scripture in the measurement file then please let me know.

  Thank you in advance.

  This example here is for a single file and a channel, you should be able to loop over that automatically. The background commentary should be the name of the channel, no group namede the name of the channel in the control.

  

• Error rate scanning for digital USB MCC-7202 / Limitation

  Someone at - he heard or why there is a limit of 100 Hz on the digital input on this forum module?  I would like to be able to watch a digital signal of 1 Khz as a trigger for a system.  Thanks in advance!

  

  I check with the experts, but the message indicates that this device will use DIO who is pace software, no hardware to the rhythm.

  It doesn't look like this device has a hardware clock or e/s high-speed digital pads.

  Therefore, the best rate that you will see with DASYLab is 100 Hz, the use on PC synchronization.

  One option is to simply read the digital signal with an analog input. You may need to use the scale or module to trigger to force the values of voltage 0V and 5V, to match the low TTL and TTL high specifications.

• -Error 209801 high-speed

  Hello

  I'm currentyl mocking a closed loop system and I encounter some performance issues. The detail is in the attachment.

  Best regards

  Thumble,

  1. 4 kHz is fast enough for a VeriStand system.  Not to say that it is impossible, but just wanted you to know.  Usually, we run our 1 or 2 kHz.  If you look at your screenshot which includes the number of loops to HP, you can see that your system is trolling way.  The number of HP is the number of times where your main loop finished late.
  
  
  2. Filtering of the DAQ errors will simply ignore errors coming from your data acquisition tasks (the error you see is your task of AO).
  
  
  3. The DAQ error indicates essentially that you aren't juggling with the card.  Since you say that the card you plan to go to 4 kHz, it expects a new sample of VeriStand at this rate.  However, your curls VeriStand currently do not run that fast, then when they fall the DAQ card throw this error because there is no data to write.

• Windows Mail SSL error ox800cccod.

  original title: ox800cccod

  When I want to use windows mail to send e-mail, the following error message appears:

  The host "SSL" is not found. Please check that you have entered the server name correctly.

  Are subject: RE: debit order 11 Manson Rd Newlands', account: 'POP3', server: 'SSL', Protocol: SMTP, Port: 25, secure (SSL): no, Socket error: 11001, error number: 0x800CCC0D

  Only, this started when I moved to Australia and began using dodo dial-up.  used to have broadband service.  the Hotmail account ok, but not when I want to access windows messages

  You seem to have the wrong settings for the account.  Try contacting your email provider and check that need to be addressed.

  Steve

• Agent of the NAC this SSL error

  Running

  CAM: 4.5.0 lite

  Current Windows clean access Agent Version: 4.5.0.0

  Current Windows clean access Agent Patch Version: 4.5.0.0

  Agent Macintosh's own access current version: 4.5.0.0

  Course Cisco NAC Web Agent Version: 4.5.0

  (Clean access windows agent installed on the host (Vista Business) is version 4.5.1.0)

  CAS mode: L2 virtual OOB GW

  The installation program is in conditions of laboratory for a proof of concept.

  The following scenario occurs each time a new authentication is attempted from a vista host running the agent access.

  -------------

  I plug the host on the controlled NAC switch port

  I get an ip address although my pool of vlan and dhcp auth

  Agent of Cisco clean access is displayed on the screen according to the normal

  I enter my user and pass and click login

  I get a "security alert" pop up indicating "the revocation information of the certificate for this site is not available. Do you want to continue? »

  There are 3 buttons to choose: Yes, no, display certificates

  I click Yes, but the error message does not disappear,... no matter how many times you click on Yes,... the error remains on the screen, keep you from making the connection.

  If I click on no.

  The clean access agent then says "network error!, detail: Certificate SSL REV failed [12057]."

  My only option is to click on the "Close" button so I don't

  This closes the agent clean access, but the agent instantly appears buck on my screen asking again user them and pass.

  I enter the right user and pass and click login

  I receive a new security alert pop up stating "this page requires a secure connection which includes server authentication." "The issuer of certificate for this site is unknown or unreliable, making you go?

  My click Options, Yes, no, view the certificate or more information

  I click on Yes, the security alert disappears and own access now States that I managed to connect to the network.

  It refreshes my IP address and puts me in the vlan correct based on the role of my user name.

  -------------

  I checked the event logs, all my access attempts are accepted, (on the 2nd try of course), but there is no errors in the cam on this SSL problem.

  However, I get a warning red text on the summary page of the cam, which stipulates the following, which I do not know if it has any impact on my problem.

  "WARNING: the end-entity certificate issued by"www.perfigo.com"is suitable for laboratory environments only." You must import a certificate of third party entity end for your own Access Manager and own access servers before the Cisco NAC Appliance deployment in a production environment. Please check your own access servers and ensures Clean Access Manager for similar messages.

  WARNING: The current "www.perfigo.com" trusted certification authority is suitable for laboratory environments only. Cisco recommends to import a third-party certification authority. Please check your own access servers and ensures Clean Access Manager for similar messages. »

  My questions are,

  -Why used the CAA accepts the first authentication attempt?

  -How can I remove the first security alert?

  -How can I set the CCA so that I login just once without having to click on no and wait for CAA to appear a 2nd time?

  Thank you all

  The fundamental problem is that the customer is unable to check the root certificate for your CASE.

  I guess that since you have always the perfigo warning that you have not installed a certificate valid on the job. If you did, you must remove the certificate of perfigo. If you install a valid certificate, you must remove the Perfigo cert.

  Once you have a valid cert installed, make sure that the client can access the certificate server root of the AUTH VLAN. That should get rid of these two messages.

  If you cannot provide access to the certificate server, then you cannot get rid of the second message, but you can get rid of the first message (the one that sticks you in a loop).

  This message (the first one) is due because the check certificate revocation in Internet Explorer has been enabled. This option has been disabled by default in XP, but is enabled by default in Vista. The option is disabled in Internet Options > Advanced tab > check the CRL.

• FRM-41211: integration failure SSL error running another product

  Dear all,

  
  

  I am facing some problems, FRM-41211: error integration SSL failure running another product.

  
  

  I'd really appreciate if someone will help me.

  
  

  Thank you.

  
  

  Laetitia

  user528488 wrote:

  Our database is 9i all in forms and reports are the two 6i

  In general, you will get the message when try to run reports. Right?

  Re-install Reports will solve this problem.

  Better uninstall and install.

  Hamid

• Certificate SSL ERROR - problem

  I created a new website for a client www.paradoxoil.com the website designer previous position an SSL certificate on the domain name and now in google search, the field appears with https://

  I saw in some forum posts on this topic but not a real answer that I can understand. Someone said about editing some links for guarantee? Some have said about adding a 301 redirect. I have contact the guys from domain associated with this account and they removed the certificate but it still appears in google the error message still appears. I tried to add the domain name in google as http://www.paradoxoil.com God knows how long it will take to change.

  Any help would be appreciated 100%.

  

  Hello

  You can see the Google link removal tool,

  https://www.Google.com/webmasters/tools/removals

  Also, check out this link to learn more about the procedure,

  Remove old or information deleted from Google - search Console Help

  Unfortunately there is no guarantee by Google when these links will be removed and here's why, but should be useful.