Star topology to VPN, hub using two interfaces

Similar Questions

• Can I use two vpn set in my iPhone?

  Can I use two vpn set in my iPhone?

  Yes, you can use but not at the same time. You can add more than one vpn on your iPhone but can only use one at a time. Another way to use the two VPN at the same time, is that you can have an extra router to connect the two VPN at the same time. For more information on this, you can take a look at these answers https://www.quora.com/Why-cant-I-use-two-VPN-at-the-same-time hope this will solve your problem to his subject.

• Site to site VPN (ASA-> router IOS, with two interfaces) help

  Dear,

  I need help to configure VPN from Site to Site of cisco ASA to the IOS router, the router has 2 WAN links, a primary and secondary backup.

  There was only a single week of link there is, now we have installed the second link as a backup, we use OSPF as the routing protocol.

  VPN with simple link worked fine, now, when the main link fails the network is down.

  Waiting for response.

  There is an easy solution.  On the router, you must terminate the VPN on the loopback interface.

  something like this:

  interface lo0

  IP x.x.x.x where x.x.x.x

  card crypto-address lo0

  interface wan_1

  vpn crypto card

  interface wan_2

  vpn crypto card

  One condition is that the loopback interface has accessible by the device of the SAA.

• Question of redundancy VPN l2l using 2811 as endpoint devices

  I have a new implementation of VPN L2L passes using two 2811 s than VPN terminal devices. I'll try to use the HSRP address between the public interfaces of both routers as VPN peer address. The problem that I found during the test is that the tunnel will become active and debugs watch the HSRP address as an invalid address to form the tunnel. Have a work-around, or a better plan for redundancy on peering address using similar devices? Thanks in advance.

  Take a look at this doc about IOS IPSec HA.

  http://www.Cisco.com/en/us/docs/iOS/security/configuration/guide/sec_vpn_ha_enhance_ps6922_TSD_Products_Configuration_Guide_Chapter.html#wp1039849

• Easy VPN with the Tunnel Interface virtual IPSec dynamic

  Hi all

  I configured easy vpn remote on a cisco 1841 and dynamic server easy vpn with virtual tunnel interface on the server (cisco 7200, 12.4.15T14)

  http://www.Cisco.com/en/us/partner/prod/collateral/iosswrel/ps6537/ps6586/ps6635/prod_white_paper0900aecd803645b5.html

  It works with easy vpn remote to the client mode and mode network-extesión, but it doesn't seem to work when I configure mode plus network on the client of the cpe, or when I try to have TWO inside the ez crypto interfaces. On the customer's site, I see two associations of security, but on the server PE site only security SA!

  Without virtual dynamic tunnel interface, dynamic map configuration is ok... This is a limitation of the virtual tunnnel dynamic interface?

  Federica

  If one side is DVTI and the other uses a dynamic map, it does support only 1 SA. If the two end uses DVTI or the two end uses dynamic card then it supports several SAs.

  Here is the note of documentation for your reference:

  Note: Multiple inside interfaces are supported only when the Cisco Easy VPN server and the Cisco Easy VPN client have the same type of Easy VPN configuration. In other words, both must use a Legacy Easy VPN configuration, or both must use a DVTI configuration.
  
  

  Here's the URL:

  http://www.Cisco.com/en/us/docs/iOS/sec_secure_connectivity/configuration/guide/sec_easy_vpn_rem_ps6441_TSD_Products_Configuration_Guide_Chapter.html#wp1046365

  Hope that answers your question.

• VPN Hub and Spoke with NAT

  Hello! I have a VPN network star topology, I need configuration for our customers to access. I have 3 points of endpoint in this example: VPN, Pix 515e and Linksys RV042 hub. The hub is the site of our parent company, the Pix 515e is our data center and the RV042 is at the customer's site. What I currently have is a VPN connection between our Pix 515e and the hub, and another between our Pix 515e and the RV042 VPN. What I need is for the server on the client (RV042) site to talk to the hub network via our Pix 515e. I also need to be coordinated traffic so it looks like it's from the same subnet on our Pix 515e to the hub.

  Hub (MEAN): 10.1.6.x

  PIX 515e (HUB): 172.16.3.x

  RV042 (SPOKEN): 192.168.71.x

  PIX 515e (HUB):

  Outside - 12.34.56.78

  Interior - 172.16.1.1

  Hub (TALK):

  Outside - 87.65.43.21

  Interior - 10.1.6.1

  RV042 (SPOKEN):

  Outside - 150.150.150.150

  Interior - 192.168.71.1

  The hub allows all traffic to my Pix 515e on subnet 172.16.3.x and vice versa. The RV042 allows all traffic from 172.16.3.x to talk to 192.168.71.x and vice versa. I need to get 192.168.71.5 on RV042 network 10.1.6.x the network hub through the Pix 515e and make it look like its 172.16.3.71 entry. So I need NAT traffic in the tunnel to another tunnel. Attached config running under the direction of privacy. Any help is greatly appreciated.

  On PIX you need a static policy statement,

  NAT list allowed access host ip 192.168.71.5 10.1.6.0 255.255.255.0

  public static 172.16.3.71 (external, outside) 192.168.71.5 nat access list

  And modify the ACL of appropriately crypto to include natted address.

• Unable to connect to the Cisco VPN you use native client: El Capitan

  I'm unable to connect to the Cisco VPN using native client server Cisco OSX via IPSec. Before the upgrade for connections VPN El Capitan has worked without any problems. VPN uses the shared secret of group. It seems, I get the error "raccoon [2580] ': could not send message vpn_control: Broken pipe ' during the connection."

  When I upgraded to El Capitan, VPN connection has stopped working. I tried to do the following:

  * connect using the old work VPN connection: without success

  Config: Hand [server address, account name],

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  ...

  * Add new VPN connection using L2TP over IPSec: without success

  Config: Hand [server address, account name],

  Authentication settings [user authentication: password, identification of the Machine: Shared Secret].

  Advanced [send all traffic on the VPN = TRUE]

  errsors:

  "pppd [2616]: password not found in the system keychain.

  "authd [124]: copy_rights: _server_authorize failed.

  ...

  
  

  * Add new connection using Cisco via IPSec VPN: without success

  Main config: [server address, account name].

  AUTH settings [shared secret, the Group name].

  Advanced [mode to use the passive FTP = TRUE]

  errors:

  "authd [124]: copy_rights: _server_authorize failed.

  "raccoon [2580]: could not send message vpn_control: Broken pipe"

  VPN server is high and does not work and accepts connections, this problem is entirely on the client side.

  I. Journal of Console app existing/Legacy VPN connection:

  26/03/16 10:24:01, 000 syslogd [40]: sender ASL statistics

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: received an order to start SystemUIServer [2346]

  26/03/16 10:24:01, nesessionmanager 311 [2112]: NESMLegacySession [VPN_CONN_NAME$: B7816CCC-2D2C-4D6D - 83 D 9-B2C8B6EB8589]: changed to connecting status

  26/03/16 10:24:01, nesessionmanager 313 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, 316 nesessionmanager [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 338 [2580]: agreed to the takeover of vpn connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 339 [2580]: connection.

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 339 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 349 [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 350 [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, racoon 381 [2580]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:24:01, 381 nesessionmanager [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:24:01, nesessionmanager 404 [2112]: phase 1 of the IPSec from.

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 404 [2580]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 405 [2580]: connection.

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, racoon 405 [2580]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:24:01, 407 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, 407 raccoon [2580]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, racoon 436 [2580]: port 62465 anticipated, but 0

  26/03/16 10:24:01, 463 raccoon [2580]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:24:01, 463 raccoon [2580]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:24:01, 463 raccoon [2580]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 463 raccoon [2580]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, 484 raccoon [2580]: IPSec Extended requested authentication.

  26/03/16 10:24:01, nesessionmanager 485 [2112]: IPSec asking extended authentication.

  [26/03/16 10:24:01, 494 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed by disconnecting

  26/03/16 10:24:01, 495 nesessionmanager [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 495 [2580]: IKE Packet: forward the success. (Information message).

  26/03/16 10:24:01, racoon 495 [2580]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  26/03/16 10:24:01, racoon 495 [2580]: could not send message vpn_control: Broken pipe

  [26/03/16 10:24:01, 496 nesessionmanager [2112]: NESMLegacySession[$VPN-CONN-NAME:B7816CCC-2D2C-4D6D-83D9-B2C8B6EB8589]: status changed to offline, last stop reason no

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:24:01, racoon 496 [2580]: IPSec disconnection from the server $VPN_SERVER_IP

  $VPN_SERVER_IP

  II. new VPN connection using L2TP over IPSec Console app log:

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetFillColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetStrokeColorWithColor: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextFillRects: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextSetCompositeOperation: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextClipToRect: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 293 com.apple.preference.network.remoteservice [2539]: CGContextGetFontAntialiasingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetShouldSmoothFonts: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextGetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, 294 com.apple.preference.network.remoteservice [2539]: CGContextSetFontSmoothingStyle: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetDefaultUserSpaceToDeviceSpaceTransform: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, com.apple.preference.network.remoteservice [2539 295]: CGContextConcatCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextSaveGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextDrawImages: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextRestoreGState: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:26, [2539 295] com.apple.preference.network.remoteservice: CGContextGetCTM: context invalid 0x0. If you want to see the trail, please set CG_CONTEXT_SHOW_BACKTRACE environment variable.

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveTrackingHandler:-1856

  26/03/16 10:37:28, [2539 339] com.apple.preference.network.remoteservice: error in CoreDragRemoveReceiveHandler:-1856

  26/03/16 10:37:28, com.apple.xpc.launchd [1 393]: (com.apple.SystemUIServer.agent [2346]) Service was released due to the signal: Broken pipe: 13

  26/03/16 10:37:28, Spotlight 461 [459]: spot: logging agent

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, [2539 487] com.apple.preference.network.remoteservice: service - area of the one error ERROR = NEConfigurationErrorDomain Code = 9 "configuration is unchanged" UserInfo = {NSLocalizedDescription = configuration is unchanged}

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: received an order to start com.apple.preference.network.re [2539]

  26/03/16 10:37:28, nesessionmanager 519 [2112]: NESMLegacySession [VPN_CONN_NAME$: 04c 10954-16 b 2 - 40BB - B3F1 - 9288F968029E]: changed to connecting status

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: rules of problem opening the file "/ etc/authorization ': no such file or directory

  26/03/16 10:37:28, com.apple.SecurityServer [75 536]: sandbox has denied authorizing the right "system.keychain.modify" customer "/ usr/libexec/nehelper" [184]

  26/03/16 10:37:28, 536 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, 538 pppd [2616]: NetworkExtension is the controller

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: cannot copy content, returned SecKeychainItemCopyContent user interaction is not allowed.

  26/03/16 10:37:28, nehelper 540 [184]: 10954-16 b 2 - 40BB - B3F1 04c - 9288F968029E: SecKeychainItemFreeContent returned the user interaction is not allowed.

  26/03/16 10:37:28, 570 pppd [2616]: password not found in the system keychain

  26/03/16 10:37:28, 572 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: publish_entry SCDSet() failed: success!

  26/03/16 10:37:28, 573 pppd [2616]: pppd 2.4.2 (Apple version 809.40.5) started by $VPN_SERVER_USER, uid 501

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceConnectedCallback

  26/03/16 10:37:28, SystemUIServer 620 [2615]: [BluetoothHIDDeviceController] EventServiceDisconnectedCallback

  26/03/16 10:37:28, authd 720 [124]: copy_rights: _server_authorize failed

  26/03/16 10:37:28, sandboxd 748 [120]: nehelper (184) ([184]) refuse the authorization-right-get system.keychain.modify

  III. New connection of Cisco VPN through IPSec Console app log:

  26/03/16 10:18:26, 917 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  26/03/16 10:19:43, 975 WindowServer [172]: _CGXRemoveWindowFromWindowMovementGroup: 0x10d of window is not attached to the window 0x10f

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: received an order to start SystemUIServer [2346]

  [26/03/16 10:19:56 nesessionmanager 265 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: changed to connecting status

  26/03/16 10:19:56, nesessionmanager 267 [2112]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, nesessionmanager 270 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, authd 284 [124]: copy_rights: _server_authorize failed

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: agreed to the takeover of vpn connection.

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 295 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 296 [2576]: connection.

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 296 [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 308 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 308 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, 352 raccoon [2576]: no message must be encrypted, 0x14a1, side 0 status

  26/03/16 10:19:56, nesessionmanager 352 [2112]: Controller IPSec: IKE FAILED. phase 2, assert 0

  26/03/16 10:19:56, nesessionmanager 353 [2112]: Controller IPSec: retry the aggressive mode IPSec with DH group 2

  26/03/16 10:19:56, nesessionmanager 373 [2112]: phase 1 of the IPSec from.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec to connect to the server $VPN_SERVER_IP

  26/03/16 10:19:56, 374 raccoon [2576]: connection.

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, 374 raccoon [2576]: IPSec Phase 1 started (initiated by me).

  26/03/16 10:19:56, racoon 376 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 1 message).

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 376 [2576]: > > > > > status of phase change = Phase 1 began by us

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 404 [2576]: port 62465 anticipated, but 0

  26/03/16 10:19:56, racoon 432 [2576]: IKEv1 Phase 1 AUTH: success. (Initiator, aggressive-Mode Message 2).

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: > > > > > status of phase change = Phase 1 began with a peer

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: receive a success. (Initiator, Aggressive Mode 2 message).

  26/03/16 10:19:56, racoon 432 [2576]: initiating IKEv1 Phase 1: success. (Initiator, aggressive Mode).

  26/03/16 10:19:56, racoon 432 [2576]: IKE Packet: forward the success. (Initiator, Aggressive Mode 3 message).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, 433 raccoon [2576]: IPSec Phase 1 established (initiated by me).

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, racoon 453 [2576]: IPSec Extended requested authentication.

  26/03/16 10:19:56, 454 nesessionmanager [2112]: IPSec asking extended authentication.

  [26/03/16 10:19:56, nesessionmanager 464 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed by disconnecting

  26/03/16 10:19:56, nesessionmanager 464 [2112]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, racoon 465 [2576]: IKE Packet: forward the success. (Information message).

  26/03/16 10:19:56, racoon 465 [2576]: IKEv1-Information Notice: pass success. (Delete the ISAKMP Security Association).

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  26/03/16 10:19:56, racoon 465 [2576]: could not send message vpn_control: Broken pipe

  [26/03/16 10:19:56, nesessionmanager 465 [2112]: NESMLegacySession[$VPN-CONN-NAME:72874CC0-2A89-4B61-80F1-9BB4F3EA953B]: status changed to offline, last stop reason no

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: glob found no match for the path "/ var/run/racoon/*.conf".

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  26/03/16 10:19:56, 466 raccoon [2576]: IPSec disconnection from the server $VPN_SERVER_IP

  It seems that I solved the problem, but I'm not sure it helped.

  After restart of the operating system, the two connections: old and new Cisco via IPSec connection, began to work.

• How to use two external monitors with my laptop?

  I have a new Pavilion dm4-301 d cl Entertainment PC.   My OS is Windows 7.   I'm used to using two external monitors with a docking station.   This new laptop lacks a docking station.  What should I do use two external monitors?

  Certainly not without a dock, but even with laptop HP well enough docks limit you to one of the ports on the external monitor, even if there are two on the dock. We used a device called an Atlona AT-HDPIX2 which is a USB to hdmi adapter. It provides a feature of third monitor for a laptop... use the native external port of the screen and the computer screen internal, then this device gives a third control that is fully configurable to display Windows 7 interface... clone, extend, etc.. It allows a full HD resolution and is pretty responsive for games even light.  HP does not have any true docking station for your laptop.

• Two interfaces WAN ISP in the same network

  Hello world

  I am faced with a really simple but delicate scenario. My ISP gives me IP addresses public 2, both in the same network. They also gave me the default gateway which is of course in the same network too.

  I need two fully operational ip addresses, but I realized that I can't have two interfaces (routed interfaces) in the same network segment. I have just a single router (Cisco 2911). A friend told me that I might be able to set this up using VRF, but as far as I have read, there is no way to use VRF to achieve this.

  Is it possible to use two (or more) ip addresses to redirect traffic to the same default gateway in the same router?

  Thank you!

  Miguel

  Hi Miguel,.

  If you want just your 2911 have set up two public IP addresses, you can set one of them as secondary IP address. Suppose that 192.0.2.1/29 is your default gateway, and 192.0.2.2/29 and 192.0.2.3/29 are your IP addresses. So to have both configured, you'd:

  interface Gigabit0/0/0 ip address 192.0.2.2 255.255.255.248 ip address 192.0.2.3 255.255.255.248 secondary

  And voila - that should do the trick :) Best regards, Peter

• Using two 2 monitors with Windows 7

  I try to use 2 monitors with windows 7 for my wife can work at home connected to the workstation via the vpn.  We are able to use two screens while workinig offline (for example. Able to drag and use programs from one screen to another).  However when it is connected to his work station we are not able to drag and use both programs on different screens.

  On Fri, 24 Sep 2010 12:53:35 + 0000, Safert39 wrote:
   
  > I try to use 2 monitors with windows 7 for my wife can work at home connected to the workstation via the vpn.  We are able to use two screens while workinig offline (for example. Able to drag and use programs from one screen to another).  However when it is connected to his work station we are not able to drag and use both programs on different screens.
   
   
   
  Right. If I understand what you're saying, you can
  not do it.
   
   
  --
  Ken Blake
   

  Ken Blake (MS-MVP)

• Question about encryption for a VPN established between two of our sites

  We have two routers Cisco 2951, one at our main location and one at a branch.  An engineer for a local company came and worked all the parameters, including the VPN between the two men.

  For an upcoming exam, the firm wanted to know what kind of security/encryption has been implemented between the two routers.  The engineer is no longer available, so I've went over our configuration files for each of the routers and will have questions about what to tell them (I'll be the first to admit that some of this stuff is over my head).

  I enclose the portions of the configs with "crypto" information he put in place.  If you see something wrong, or need something extra, let me know.

  Thanks in advance!

  That's what you use:

  Phase 1: 3DES, SHA1, PSK, Group2 DH (1024 bits), life time 86400 s

  Phase2: 3DES, SHA1

  Which is today considered legacy crypto, but probably nothing to worry. The crypto-config has always considered that there is "room for improvement"...

• Using Loopback Interface as Source GRE/IPSec tunnel

  Hi all:

  I need one to spend a working router to router VPN tunnel using an IP WAN IP interface loopback as a source.  I am able to ping the loopback from the other router.  As soon as I change the source of tunnel to use the loopback IP address, change the encryption ACL map, and move the cryptographic card of the WAN interface to the loopback interface, the tunnel will not come to the top.  If I remove all the crypto config, the tunnel comes up fine as just a GRE tunnel.  On the other router, I see the message that says that's not encrypting the traffic below.

  * 00:10:33.515 Mar 1: % CRYPTO-4-RECVD_PKT_NOT_IPSEC: Rec'd package not an IPSEC packet. (ip) vrf/adr_dest = 192.168.0.1, src_addr = 192.168.1.2, prot = 47

  What Miss me?  Is there something else that needs to be done to use the closure of a GRE/IPSec tunnel?

  I have install below config in the laboratory to see if I can get it even work in a non-production environment.

  R1 WAN IP: 192.168.0.1

  R2 WAN IP: 192.168.0.2

  R2 Closure: 192.168.1.2

  hostname R2

  !

  crypto ISAKMP policy 1

  BA 3des

  md5 hash

  preshared authentication

  Group 2

  ISAKMP crypto key abc123 address 192.168.0.1

  !

  Crypto ipsec transform-set esp-3des esp-md5-hmac T1

  transport mode

  !

  crypto map 1 VPN ipsec-isakmp

  Description remote control

  defined peer 192.168.0.1

  game of transformation-T1

  match address VPN1

  !

  interface Loopback0

  IP 192.168.1.2 255.255.255.255

  VPN crypto card

  !

  Tunnel1 interface

  IP 172.30.240.2 255.255.255.252

  IP mtu 1440

  KeepAlive 10 3

  tunnel source 192.168.1.2

  tunnel destination 192.168.0.1

  VPN crypto card

  !

  interface FastEthernet0

  IP 192.168.0.2 255.255.255.0

  !

  VPN1 extended IP access list

  allow ACCORD 192.168.1.2 host 192.168.0.1

  you have tried to add "card crypto VPN 1 - address Loopback0".

• ACS appliance multiple use of interface

  Is it possible for me to use both interfaces are available in the 1113 box? I want to connect these two interfaces to two separate network segments. I did find something specific in the Cosole except the fixed ip that would be only an interface unique config.

  Thank you

  You can use only one.

  Your system of 1113 Cisco integrated 10/100/1000 megabits - per second (Mbps) Ethernet connectors. ACS SE takes care of the operation of an Ethernet connector, but not the two connectors.

  For more check here

  http://www.Cisco.com/en/us/docs/net_mgmt/cisco_secure_access_control_server_for_solution_engine/4.1/installation/guide/solution_engine/ovrvuap.html#wp1054065

• ASA 5520: SSL VPN by using a different IP address that the ASA public IP address

  Hi guys,.

  I'm trying to configure an SSL VPN on a Cisco ASA5520.

  Unfortunately port 443 interface OUTSIDE of the SAA is already used by Microsoft Outlook Web Access and I can not change the configuration of Outlook. This configuration already in place allows me to use the public IP address of the ASA as IP Cisco VPN for the Web page.

  I don't not want to use a different port so to keep life easy for users.

  I have a few available public IPs that I can use so I wanted to use one of them instead of the OUTSIDE of the ASA interface. Any idea how I could do?

  Thank you

  Dario

  Unfortunately you can not use any other public ip address, except the ASA outside IP interface to complete the SSL VPN.

  The only options that you have is to change the Outlook to use another port or the SSL VPN to use a different port.

• This allows traffic between two interfaces ethernet on a PIX

  I have a PIX with interface inside, IP 10.198.16.1. It also has an interface called WTS, IP 10.12.60.1. I'm having difficulty to allow traffic from the 10.198.16.0 network to cross the PIX in 10.12.60.0. I'm trying specifically to allow access to a server with an IP address of 10.12.60.2.

  I enclose my config. Any help would be greatly appreciated!

  OK, so the inside interface has a security level of 100, WTS has a security level of 75, so traffic from inside to WTS is considered outbound traffic, which is allowed by default. All you need is a pair of nat/global (or static) between both interfaces so that the PIX knows how NAT traffic between two interfaces (remember, the PIX do NAT).

  You have this in your config file:

  NAT (inside) 1 10.0.0.0 255.0.0.0 0 0

  who says all traffic inside, interface with the IP 10.x.x.x address will be NAT would have, but you must then a global for the interface WTS define what those IPS will be NAT would.

  Adding:

  Global (WTS) 1 interface

  will be PAT all inside resolves the IP address of the interface WTS and allow traffic to flow between the interfaces. If you prefer the hosts inside the interface to appear as their own IP address on the WTS network, then you can use a static command and NAT addresses themselves, actually doing NAT, but not actually change addresses:

  static (inside, WTS) 10.198.16.1 10.198.16.1 netmask 255.255.240.0

  Hope that helps.