start the host vi pxi

Similar Questions

• Start the host program automatically starts the RT program

  Hey guys,.

  I'm in a test phase and wanted to ask if it is possible to start the RTW program automatically, when I start my host VI. I don't have any executable for the moment because I am in the test phase, but I only want to support on "the button execute on the host VI and start (RT and HOST) screws.

  Is that possible or do I have to press two buttons to run?

  Kind regards

  Slev1n

  As Crossrulz notes, LabVIEW RT is essentially to another computer, does not Windows but rather running a real-time operating system (if on PharLap an Intel processor, often a version of Linux on FPGA hardware, I think).  It has always been necessary for these targets of RT to be 'on' and 'something', of course.  In the early days of LabVIEW Real-time, they sat often slowed down and you would use VI server to download and launch your RT code on them.  With the advent of the LabVIEW project (much) better to manage the objectives of the RT as, OR goes to a slightly different model where, as Crossrulz points out, the RT Code is supposed to be downloaded to the target and configured to start automatically running when the target is powered.

  In development Mode, there are provisions to download ("Deploy") and start the target RT and (theoretically), it should be possible to do it programmatically.  I tried to do this, but it was noticeably awkward that I have "gave in" and (except when in development Mode) practical to develop recommended follow-up of OR deploy and defined as starting on the target of RT.

  The idea, of course, is that if you know that the target RT is running when you start the host, the target should wait for the host to send a signal saying ' Hi, Target, are you ready to start working with me? (the target, of course, answered "Sure, let's get started...") »).  How to set up the first handshakes, it is up to you.

  Note that this model assumes / requires that until the host stops, it informs the RT target that she came out, allowing target RT back to its State "in expectation of the host."  A really simple way to do this, of course, is for the host to tell the target to reboot, which in fact boost its Startup Code (which is the target RT program).

  Bob Schor

• possible to start the MXI-3/PXI system after booting the PC?

  Hello

  I'm new here, so I just asked this question in another thread with a response. I did not notice that it was already marked as solved, so I'll ask again in my own thread.

  My problem sounds very akin to that of Kobi, but there are a few differences that hold my hopes up that the problem could be solved. Summary of the configuration of the system:

  -PC (MXI-3)

  -> PXI1002 (Chassis1)

  -> PXI8335 (port1 - in)

  -> PXI8335 (port2 - out)

  -> PXI5122 (measure)

  -> PXI1002 (Chassis2)

  -> PXI8335 (port1 - in)

  -> PXI5122 (measure)

  The goal is, as it is easy to guess, to be able to start at any time, additional measuring devices even when the pc is already running.

  The situation is different from ' Kobis in a precise point: in my case the cards and all equipment is permanently visible in MAX, even if I started after the pc has started. This change is the boss of the leds, and PXI cards do not pass the test in MAX. The following screenshot shows the configuration of the system how it is observed after the two ways to start the full system (first first pc or PXI).

  

  (Even if I use a German version of labview English my MAX partially keep, I hope this isn't a problem.)

  I have tried to identify the PXI system and chassis, but failed to get a different result. The NIscope screws are ordered initialization and reset of all sessions, but only if I turn first PXI systems.

  So you think it would be possible to achieve the goal of implementation, or should I stick to the start-up of the pc after turning on the PXIs? I did some research and I know, the installation guides to specify the order to turn on the devices, but I thought that it was only intended for installation/first round.

  I would be really grateful for any advice in the present.

  Concerning

  Max1744

  Hi Max,.

  There is no way around first PXI. Always start the PXI a d, then the PC system.

  concerning

  Tobias

• Start the host lock screen remote desktop session

  Is it possible to call the lock of a host machine screen remote desktop without interfering with any active session on this host?

  The host machine might have been locked by someone who just walked away from him or the host computer can be used remotely by its regular users.

  But despite this, I would use it to run a remote session to my regular machine.

  Hello

  Please contact Microsoft Community.

  I understand you are trying to call the remote desktop of the lock of a host machine screen. I suggest you post your question on scientists on TechNet.

  https://social.technet.Microsoft.com/forums/en-us/home?category=w7itpro&filter=AllTypes&sort=lastpostdesc

  Hope this information helps.

• cRIO: best way to start/run a VI running on the RT.vi of the host.vi

  Hi all

  I recently (3 weeks) he started to use with Labview/cRIO. I think I have the concept of the cRIO down, but I'm fighting on what seems to be a simple communication in Labview. Here's my problem:

  I have a cRIO 9074 with x 1 NI 9234 (4 analog input channels) and x 3 modules NI 9512 (motor controller). I am running in hybrid mode. My RT.vi control all movements of engine (scan mode) and also the FPGA FIFO beginning/read it. My Host.vi is in fact a UI and did some post processing on the data that I acquire by my NI 9234. My issue is with how to begin the RT.vi of the Host.vi. Just use the "VI reference.vi open? I tried but I do not think I do it properly, because what settings should I get for this? Can I configure it with the IP address of the RT? Also, for the path of the file, where are the screws on the RT?

  Thank you!

  Troy

  Note: The final product must be converted into a .exe. If the implementing method is to open/run the RT.vi automatically.

  Normally you compile the application of RT, deploy and set it as the startup application.  In this way, it will be saved on the internal flash of the cRIO drive and will automatically load when you start the cRIO.  What is an option for you?

• "The hosted network could not be started."

  I recently bought a Samsung Galaxy S2 and when trying to connect to my Wifi network, I found that the signal from the router was not strong enough to reach the floor, and since I have a laptop connected with a cable that I thought I could make it work like a virtual router. After some research, I found several programs:

  I tried Connectify, which did not work. Then I tried Virtual Router, that does not work either. Then, I found this:

  http://www.techylabs.com/setting-up-a-virtual-router-in-Windows-7.html

  And it worked, the network appeared in the list on my phone. Unfortunately, when you try to connect, it got stuck on ' Optaining IP-address '.

  I tried to use a static IP address, and even with one put in place, it got stuck on ' Optaining IP-address '.

  After that, I have been clicking through the menus a lot and hit accidentally turn off somewhere. Since then, when I try to start the virtual router, it says:

  The hosted network could not be started.

  The group or resource is not in the correct state to perform the requested operation.

  I can't find the place where I hit the turn off, and I don't know what to do more :(

  Hello

  I suggest you to see link below and check if it helps.

  WiFi/SoftAP virtual fails to start with "the hosted network could not start" on Windows 7 and Windows Server 2008 R2: http://support.microsoft.com/kb/2625519

  Hope this information is useful.

• Wi - Fi connection error: the hosted network could not be started.

  Original title: need help Urgent

  I get this error message. I'm not able to start the wifi sharing in my lenovo ideacentre desktop. I'm not able to see the microsoft wifi adapater everywhere in my office, even in the Device Manager and the adapter option Add.

  C:\Windows\System32>netsh wlan start hostednetwork
  The hosted network could not be started.
  The group or resource is not in the correct state to perform the requested operation.

  Hi Siddha,

  The question you posted would be better suited in the TechNet Forums; We recommend that you post your question in the TechNet Forums to get help:

  http://social.technet.Microsoft.com/forums/Windows/en-us/home?category=w8itpro

• VCenter with 2 guests, need to start the virtual machine to another host

  I lost the connection to one of the two armies in the vCenter. How to start a virtual machine saved on the host that is down. ?

  Heck, I found out how. I had to connect to the HOST and not do it from the vCenter. Got it to work.

• Cannot start the VMs on ESX 4.0 stand-alone host

  Hello

  We have two standalone ESX 4.0 host. They have recently lost power, and since then, we are unable to do anything with virtual machines.

  Security will not plug a laptop so I can't connect to a host using the vSphere Client.

  The command line, I ran:

  GetState \vm.vmx VMware-cmd < path_to_vm >

  VMware-cmd < path_to_vm > \vm.vmx start

  Both times, I get this error:

  vim.faul.HostConnectFault: unable to connect to localhost ({(vim.fault.No.Permission)

  dynamicType = < unset >;

  dynamicProperty = (vmodl. DynamicProperty) [].

  MSG = authorized to perform this operation was denied.',

  faultCause = < unset >

  faultMessage = (vmodl. LocalizableMessage) [].

  object = "vim. File: ha-folder-root',

  privilegeId = "System.View.

  })

  It seems that 'root' has lost its permissions to start the virtual machines! Unfortunately, the engineer who built the servers is therefore more around and there is no documentation for them. Can anyone suggest what that might be?

  Thank you Andre,.

  This is the user-error (shame on me).

  Before discovering the fault, I checked the article kb 1031192 and permissions in the file permission (or authentication) were right. -(1).

  It's been so long that I used ESX / Service Console that I forgot to do "su-" rather than "su root" from the non-privilegie account to the root account.

  When 'esxcfg -' orders have also failed, I Googled it and found the answer on the Blog of Simon long.

  (Google 'ESXCFG Command not Found' and found on simonlong.co.uk). This machine will not let me copy / paste so that I can not paste in the link!

  Well - I had the problem solved after that. Thanks for the reply!

  Have a great weekend people.

  Alex

• Can the VCenter or general Vm be turn on when the host starts?

  Dear:

  The VCenter or general Vm can be running when the host of start or restart?

  How to do?

  THX.

  It is possible to enable auto-start for the virtual machine, check Automating the process start and stop VMs on VMware ESX

  Also read clarification of questions to start the car in vSphere 5.0 Update 1 functionality has been disabled with vSphere 5.0 and later helped with a patch

• PowerCLI defining politics NTP to "Start and stop with the host" in ESXi 5

  Would appreciate any help in the definition of the strategy NTP on ESXi 5 hosts 'start and stop with the host. My script is currently using the following:

  Get-VMHost MyEsx | Get-VMHostService | where {$_.} Key - eq 'ntpd'} | Game-VMHostService-policy "automatic."

  This sets up the NTP service in "start automatically if all ports are open and stop when all ports are closed.

  "When I cange to 'MyEsx Get-VMHost | Get-VMHostService | where {$_.} Key - eq 'ntpd'} | Game-VMHostService-political ' market / stop with host"" the following is returned:

  «The possible enumeration values are "auto, On, Off«»»»

  Anyone know of a way (in PowerCLI) of the set up for the 'start and stop with host?

  OK, then you should choose politics "on".

  These are the policy values and what they match.

  

  Like this

  Get-VMHost MyEsx | Get-VMHostService | where {$_.Key -eq "ntpd"} | Set-VMHostService -Policy On
  

• From a device at the start of the host

  I need to make an appliance VMware launched at the start of the host.

  The device works in VMware Player 3.x on a Windows Server.

  I need to make them at the start of the host VMware Player and unit comments start.

  How can I configure VMware player to start automatically (as a service)?

  Concerning

  Mario

  here on my machine, I created a service with srvany.exe (this is a tool of MS - google knows)

  Then creates a new service and that the application to use, I have configured a lot that looks like

  start r:\vm\vmware\vmplayer.exe  F:\xmonowall\monowall.vmx
  exit
  

  during the creation of the service, you can select the account to use to run it - options are the system account or an administrator account.

  It behaves a little different - try both options and then decide what is best

  ___________________________________

  VMX-settings- Workstation FAQ -[MOA-liveCD | http://sanbarrow.com/moa241.html]- VM-infirmary

• How to set up so that VMs automatically starts when the host reboot?

  We lost power this morning and all 4 ESX hosts are down.  When the power is back, we observe that VM is not started automatically.

  We find we have not enabled 'start and stop Virtual Machines with the system.  In this way, we have allowed it.

  We'd like to know, is it necessary to move all virtual machines (those we would like to bring start automatically when the host is in place) "Manual start" to "any order"?

  In addition, as the setting is on each ESX host, will be the setting (i.e. automatic start in any order) for a particular virtual machine carried over to another ESX host if it is has been vMotioned?

  Thank you

  (1) Yes, it applies for each host and is not shared between all the other hosts and is disabled by default. You must activate it by going to configuration tab look for 'Machine virtual start/stop' to activate and set the priority/delay for your virtual machines

  (2) personally, I don't use this feature, it could be the case that the default update the settings back... it would be surprising if that were the case, I re - activate and try to stop or restart and see if that is the case. If it's the latter, I would file a ticket with VMware if you have a support contract

  (3) No, if everything is configured correctly and the change of the start/stop is retained through reboots, they should automatically turn on virtual machines in the list that you specified.

  =========================================================================

  William Lam

  VMware vExpert 2009

  Scripts for VMware ESX/ESXi and resources at: http://engineering.ucsb.edu/~duonglt/vmware/

  Twitter: @lamw

  repository scripts vGhetto

  Introduction to the vMA (tips/tricks)

  Getting started with vSphere SDK for Perl

  VMware Code Central - Scripts/code samples for developers and administrators

  150 VMware developer

  If you find this information useful, please give points to "correct" or "useful".

• How do you start automatically at startup of the host guests?

  How do you start guests automatically when starting vSphere host? I did it in vmware server and vmware workstation before easily but I can't work out how to do it for vSphere. I don't have a vCenter.

  Just use the vSphere Client and point to host, software, Configuration, start/stop the virtual machine.

• Cannot start the VMWare host agent service

  I worked on this issue for awhile with no resolution.  Initially, I had a problem running VMWare Server Home Page so I installed the VMWare Server Console and the error when trying to launch the Console VMWare Server on the same server VMWare Server is installed and connect locally:

  501 command overall GLOBAL Server-vmdb targets no host agent not supported.

  Came to the conclusiong that it was the result of the function of Agent Host VMware is not able to start.

  Environment:

  IBM BladeCenter HT chassis

  IBM eServer HS21 - 8853AC1

  NetXtreme Broadcom5704S

  2 x Quad Core Intel Xeon E5440 2.83 GHz

  Initially, I installed VMWare Server 2.0 and then upgraded to 2.0.1 to see if that would solve the issue but always without success.

  Event Viewer message:

  Host VMware Agent service terminated with service specific error 4294967295 (0XFFFFFFFF)

  Not tried so far:

  1. I tried uninstalling and reinstalling several times without success

  2. Tried to manually start the VMWare host Agent

  3. Tried the upgrade to VMWARE 2.0 VMWARE 2.0.1

  4. Tried to uninstall and reinstall

  5. Tried to launch the service as ADMINISTRATOR

  It is the only VMWare Server service that does not start... I Googled, and I can't find a resolution to this problem.

  Post edited by: RDPetruska

  Emoticon removed from the subject line.

  Check this solution or search the Internet: "panic error: not well formed (invalid token)" (sorry, I don't have the time to search for you now).

  BTW. If IIS is installed and running, try to stop and start the vmware agent

  J.

  If you have found this device or any other answer useful please consider the use of buttons useful or Correct to award points.

  Post edited by: janlib