Startup-Configuration of backup to Disk0:

Similar Questions

• Cannot configure Microsoft Backup. ERROR 0 X 80070424

  I'm unable to configure Microsoft Backup. When I try to configure the backup I get a flash of the screen bit that show progress bar moving and then the MSG of ERROR 0 x 80070424. I followed the suggestions to make sure start state, Windows Update, and workstation are set to Started. This has not solved the problem.

  Al

  Hello

  (1) did you the latest changes on the computer?

  (2) you are performing the backup of the computer, or you are trying to back up some files and folders?

  (3) are you trying to backup to another drive or the hard drive even?

  (4) who start around the high status are you referring to?

  Method 1: Search for the shadow copy of Volume.

  Step 1: Click Start, type services.msc (without the quotes) in the search bar and press enter.

  Step 2: Double click on Volume Shadow Copy Service and switch to the general tab.

  Step 3: Change the type of startup to Automatic and click on apply.

  Step 4: Click Start , and then click OK.

  Method 2:

  There will be some corruption of system files, you can perform the scan System File checker [SFC] on the computer, the scan replaces the system corrupted files with the files from the original Windows version.

  To see how to the SFC Scan click on the link below and follow the steps in the Kb article.

  http://support.Microsoft.com/kb/929833

  Note: Run the following commands in elevated command prompt, as mentioned in the above article.

  When the analysis is complete, check to see if the problem still persists.

   

  Method 3: You can also check out the link below to run a disk check:

  http://Windows.Microsoft.com/en-us/Windows-Vista/check-your-hard-disk-for-errors

  Important: All performing hard disk the disk check if bad sectors are found on the disk hard disk check is trying to repair this area if all available on which data may be lost.

                                                                                            

  I hope this helps.

• Equium A100-147: cannot install Vista because of startup configuration problem

  Equium A100-147 (Windows MCE) bought compatible Vista and bought my promised copy of Vista... used Toshiba step by step DVD ROM upgrade and also updated the Bios.

  Tried to load Vista Home Premium and after going through all the steps, it came with this message...
  «Could not update the computer startup configuration - installation cannot go ahead «...»»

  How should I proceed and what is useful to load Vista.
  Thanks in advance for any help.
  Considers that Howard.

  Hello

  How have you tried to install vista on the laptop?
  Have you tried to switch the MCE to Vista or were you running the new clean install of Vista?

  In my opinion, you must perform a clean installation. Don t updated the existing MCE of Vista.
  In such cases, you can join different installation problems

  If you are an owner of an original MS windows XP CD try to run the console of your windows XP CD recovery.
  Demarrer start from the CD at startup, and then press R to access the recovery console after loading the driver.

  In the recovery console, typefixbootand then restart your laptop.
  Then insert your Vista installation and restart.

  This should solve your problem.

• SBS 2008 backup automatic Wizard fails cannot configure the backup schedule

  I need to install a new drive for backup for SBS 2008.

  The new drive is 3 T. The backup requires 567G.

  The Backup Wizard fails with the message "cannot configure the backup schedule.

  I looked on the MS Support and the only link is related to the target being too small. Although does not here apply.

  The log file indicates that the operation failed because "the critical volumes cannot be excluded", but I included C drive in its entirety. There is a system drive D, but it is not available in the backup configuration.

  Any suggestions?

  Thanks in advance

  Murray

  It is a forum for specific consumers.

  You will find support for SBS in this forum-online http://social.technet.microsoft.com/Forums/en-US/home?forum=smallbusinessserver

• my startup configuration is corrupted

  my startup configuration is corrupted. and I tried to re - install my operating system but its does not work. Help. idk what to do

  my startup configuration is corrupted. and I tried to re - install my operating system but its does not work. Help. idk what to do

  Follow these steps to try to solve your problems of boot.

   

  Restore point:

  http://www.howtogeek.com/HOWTO/Windows-Vista/using-Windows-Vista-system-restore/

  Do Safe Mode system restore, if it is impossible to do in Normal Mode.

  Try typing F8 at startup and in the list of Boot selections, select Mode safe using ARROW top to go there > and then press ENTER.

  Try a restore of the system once, to choose a Restore Point prior to your problem...

  Click Start > programs > Accessories > system tools > system restore > choose another time > next > etc.

  http://www.windowsvistauserguide.com/system_restore.htm

  Read the above for a very good graph shows how backward more than 5 days in the System Restore Points by checking the correct box.

  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

   

  If the Mode and/or the system restore safe does not work and you do not have a Microsoft DVD of Vista (you have Dell, HP, etc.), do a repair disc to do a Startup Repair:

  Download the ISO on the link provided and make a record of repair time it starts.

  Go to your Bios/Setup, or the Boot Menu at startup and change the Boot order to make the DVD/CD drive 1st in the boot order, then reboot with the disk in the drive.

  At the startup/power on you should see at the bottom of the screen either F2 or DELETE, go to Setup/Bios or F12 for the Boot Menu.

  When you have changed that, insert the Bootable disk you did in the drive and reboot.

  http://www.bleepingcomputer.com/tutorials/tutorial148.html

  Link above shows what the process looks like and a manual, it load the repair options.

  NeoSmart containing the content of the Windows Vista DVD 'Recovery Centre', as we refer to him. It cannot be used to install or reinstall Windows Vista, and is just a Windows PE interface to recovering your PC. Technically, we could re-create this installation with downloadable media media freely from Microsoft (namely the Microsoft WAIK, several gigabyte download); but it is pretty darn decent of Microsoft to present Windows users who might not be able to create such a thing on their own.

  Read all the info on the website on how to create and use:

  http://NeoSmart.net/blog/2008/Windows-Vista-recovery-disc-download/

  ISO Burner:http://www.snapfiles.com/get/active-isoburner.html

  It's a very good Vista startup repair disk.

  You can do a system restart tool, system, etc it restore.

  It is NOT a disc of resettlement.

  And the 32-bit is what normally comes on a computer, unless 64-bit.

  See you soon.

  Mick Murphy - Microsoft partner

• Configure a backup task every night

  I want to configure a backup task every night. I'll probably have a few models in the library of work, and each will be held every night with multiple targets.
  How can I configure a report on each night works? is - to be emailed every morning to several people (failing backups etc.). I couldn't find a way to recognize a report on the situation of employment (all runs of the last execution). Advice on how to proceed?

  I10.2 SGD, you can use the framework. Reporting framework allows you to create custom reports by querying the data from Tables of EM / views.
  It also has the possibility to send reports.

  For your condition, you can query the view "MGMT$ JOB_EXECUTION_HISTORY.
  This opinion has all the information you need.

• WLC configuration or backup script?

  Hello

  I wonder if there is a way to save the WLC configuration such as a .txt file or a copy start tftp as a switch or a router command to then paste or load it to another or the same WLC.

  It's because I'm about to add a WLC backup my network whose only difference will be the name and IP address so I hope that I can avoid going step by step thanks to its configuration. Or lets say I restore default settings in my current WLC and then I want to just load a config file, or again it is a step by step process?

  Kind regards!

  The Solution has been added in the following Document: -.

  https://supportforums.Cisco.com/docs/doc-21757

  Hello

  From 5.2 or later, when you load the configuration via FTP or TFTP file, you can actually open it with a text editor and it should show a list of orders:
  http://www.Cisco.com/en/us/docs/wireless/controller/6.0/Configuration/Guide/c60mfw.html#wp1046683

  In this way, you can make changes to the text editor and load it to the WLC.
  Alternatively, you can also copy the config set as a text, switch mode config of the WLC (with the command 'config') and at the prompt "config >" just copy the entire configuration text file.

  Hope this helps,

  Fede

  --
  If this helps you or answers to your question if it you please mark it as 'responded' or write it down, if other users can easily find it.

• Configure the backup error Windows7-64

  Error code (the Server execution failed (0 x 8008005) we tried with this forum, but nothing suggested worked 7 months.)  We decided to wait a while to see if there is more on this problem. MS tried at the time, but they had no idea either.

  We will listen to all suggestions and will try new ones we have several pages of suggestions.

  Hi Rob_Gr,

  Check the status of the Volume shadow copy service and Windows backup service in the services window. Use the following steps to check:

  i. click on start and type services.msc in the search box

  II. the service search

  Make sure that the startup type is automatic. Steps to set the auto services

  III. the service search

  IV. right click on the service

  v. If the service is stopped and then starts the service

  VI. Select Properties

  VII. and in startup type, select automatic

  Try the following steps:

  i. click on the round of departure.

  II. in the search box, type CMD.

  III. right-click on cmd.exe and select run as administrator.

  IV. Enter your password if prompted.

  v. at the command prompt, type:

  net localgroup "Administrators'"NT Authority\Local Service"/ Add

  With regard to:

  Samhrutha G S - Microsoft technical support.

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Configure a backup at the request of 5.0 ESXi hosts

  Hello

  Is there anyway that I can configure a scheduled backup of 10 servers ESXi?

  Please suggest.

  Thank you

  Mihir

  Mihir salvation,

  Years ago I was also thinking around how to manage the ESX (i) to return once crashing.

  I could circle in all directions, but I come to the end that "try to save some configs" > theire is of single Point of failure.

  -Get 100% of all the files that are needed to get the config back once that crashing

  -At a Major relase change > perhaps this dependend files modification or extension

  -Restore/backup Configs, maybe causing a kind of instability...

  -Don't know if Vmware supports 100% backup and restore config

  In any case, my own Solution follows.

  Instead of save config and trying to restore > I kill 2 flies with 1 slap.

  -Fast food (but of the mind, this is a new installation and pushing scripts,...)

  -Update of the process. (New installation with the new Build number)

  I use the PXE boot solution.

  The server is much more stable.

  What I did:

  -R2 Windows 2012 with IIS + WDS

  -With the help of 2 actions

  1 x for WDS

  1 x for IIS

  IIS part = 1: Hostcfgs (Kickstart files for each host)

  2: Patch (placed the last update file)

  3: scripts (host, ntp file, the advanced settings, file exchanges,...)

  WDS share = deployment share of default windows where I place the iso extract binaries and files menu pxelinux.cfg,...

  Then at all. Once I have a strange problem. I push things kickstart and have following

  -More information freshly installed with all THE Configs as before

  And once that a new major Relase is out > it is easy to integrate to PXE.

  If you have only one initially effort and you need keep the patches (or by creating every time a new Source).

  PS: Remember, you must be sure that the system is Stable. And with a sort of backup/restore > you never 100% could be sure that this is the case. Because you know a lot of theire ID of the object in the background...  With this kind of Solution, I could be sure that I covered everything 100%.

  "vicfg-cfgbackup" is a good idea >, but never I would rely on it completely.

  Just Feedback to think in the other direction.

  Best regards

  Max

• Configuration of Backup Exec 12.5 and VCB with Windows 2008 64 bit

  Hello everyone

  Try to install the update of VMware Consolidated Backup 1.5 1 with Backup Exec 12.5 on a Windows 2008

  64-bit server.  Having a hard time getting the configuration to work.  When I try to do a restore via vCenter

  I don't get "VMware Converter not found"

  I installed Converter Stand Alone on the server, but I still get the same error.

  Some would please the VCB and Backup Exec 12.5 on a Windows 2008 Setup process

  64-bit server?

  Thanks in advance...

  Gerald S.

  Looks like you need to install vCentre Converter (the server vCentre himself) of what has been said.

  Please give points for any helpful answer.

• Configuration of backups from iCloud drive: why are there two Mobile Documents files?

  I've recently started using iCloud drive to synchronize documents between my Mac and iOS devices. Now, I want to assure you that I have local backups of these documents.

  I understand that the documents synchronized via iCloud are store locally in my Mobile user home/library/Documents folder. But when I check I made 2 folders: Documents Mobile and Mobile Documents.90391253.  The Documents Mobile folder seems to keep all the records that I created using Pages, drafts and TextEdit.  The second folder has files with obscure names such as ' JFJWWP64QD ~ com ~ goodiware ~ GoodReader. ". Records of Documents that I checked are empty.

  Here is a screenshot of the second folder:

  

  Why are there two folders of Documents Mobile? When you add a folder to a backup program, I would add two folders or just the folder Documents Mobile?

  The second folder (the one your screenshot) is a backup of an iPhone, iPad, or iPod Touch, which was made via iTunes. More information: finding and managing your backups iTunes - Apple Support

• How to configure automatic backup in apex

  How to set up an automatic backup in the apex

  First of all, can you define what you mean by a backup. IE database, schema, workspace Apex, Apex application, all the foregoing, some of the previous ones?

  André

• F2, F12, startup, configuration... Help!

  When I turn on my computer (usually by opening the lid and pressing the power button to wake the portable computer), I get this:

  WARNING: The battery cannot be identified. The system will not be able to charge this battery.

  Press a key to continue.

  
  

  I don't know what to do and were simply hit any key to continue. Battery recharge when plugged in AC. So I have no idea what that means all or what to do. F2 or F12? Help, please.

  Thank you!

  Hello enj64,

  Your battery may need to be replaced. Have you tried to remove and reinstall the battery? How old is this laptop? Maybe you should contact the manufacturer of your laptop to get help because there may be a recall on this farm. Let us know if this helps you. Make it a great day!

  "In the end, the love you take, is equal to the Love You Make"

• How to automatically configure automatic backup in flash Application?

  In FlashCS3 how automatically set auto save in the flash Application file

  Thanks in advance.

  the best you can do is click Edition/Preferences/general and check "save files on test or publish the project.

• The TMS Configuration backup

  I am a rookie with the systems and need help. I set up a backup on TMS (System > Configuration > perform backup) for our VCSC and VCSe a few days ago. I did not specify a time and expected to start immediately and run a backup on the ends of two infrastructure.

  But instead of starting, when I look in the systems > Configuration > Backup/Restore activity status indicator of progress set to 0% and remained at 0% since then.

  I did something wrong? Is there a journal I should look to see a mistake or another mssage status?

  Paul

  Hello

  If the settings tab is greyed out then you probably problem of connectivity with VCS. just try to purge the VCS of the list (do not delete but purge it) and re - add new. see if you can get the tab activitated. Also browse CVS to the system > external administrator and check if the connection is active. You can get your VCS, directly from respective VCS Server backup by navigating to the maintenance > backup and restore

  Best regards, Ahmad