No wireless access

Similar Questions

• Use WAN connected airport Time Capsule as a wireless access point

  I had to replace a failed 4 Gen Time Capsule. I tried to install a new Gen 5 airport TimeCapsule via WAN and set up the airport to act as a wireless access point. It is installed in an area of my house with wireless coverage. In the network of AirPort Utility Mode section, I chose "extend a wireless network. The TC is restarted, I get an error message cannot find the intended wireless network.

  What I lack?

  "Extend a wireless network" is a parameter that is only used if the time Capsule need to connect to another router from Apple with the help of a Wi-Fi connection.

  You use Ethernet to connect, you must use the parameter to "create a wireless network. Use the same wireless network name and the same password as your "primary" router

• Cannot connect by Satellite L300 wireless access point

  I have a new laptop L300 & I can't connect to the laptop to my wireless access point. I have an another mobile E-sytems with the same hardware Realtek RTL8187B & it connects without problems.

  The machine has the free two month Mcafee subscription & I have disabled all the protection incase that was causing the problem. I updated the driver for the wireless card & the bios on the Toshiba site, but nothing is.

  Can someone shed light on this problem because the laptop is only two weeks old?

  Thank you...

  Hello

  To connect the laptop to the WLan, it must ensure that everything is enabled and configured correctly.
  You should check these points:

  -activated the WLan with the WLan switch and the FN + F8
  -don t use any 3rd party config tools WLan if you use the WLan configuration options own Vista
  -for the first test WLan disable the security settings of the Wlan router
  -configure settings to laptop as good SSID and search for your wireless local area network
  -After that the laptop is connected to the WLan router, you can turn back the security settings (encryption, mac address filtering, firewall, etc.)

  Welcome them

• Card wireless INTEL PRO 2200 BG - don't find any wireless access point

  I just try to run internet with the internal PRO INTEL BG 2200 wireless card.
  The driver version is just updated to 9.0.4.39. The problem is, I can't find any wireless access point.

  I also use a D-Link card, with this card, I found the available access points. What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  Also, I thought that I might need to activate the wireless with additional keys Fn function, but they do not work, I guess. Maybe I need a driver for this tool also. Do anyone know where I can find drivers to use the Fn keys?

  My system:
  TOSHIBA Tecra
  WINDOWS XP (SP 3)

  See also: The INTEL internet LAN works.

  > What could be the problem with the INTEL PRO card. I'm sitting right next to the router/hub.

  For me, it seems that the WiFi network is not enabled.
  Usually, you need to activate the WLan switch which is placed on the side of the laptop. Then, you'd see an active WLan led.
  If you n t see the light, then the WiFi network has not been activated.

  In addition, choose the WLAN using FN + F8!
  You can also activate the Wlan in Device Manager-> card Wlan-> properties-> Advanced tab.

  Good bye

• Set up the wireless access point, but the wireless devices are unable to get ip address

  Hi, I wanted to put my D7000 as router AP. My main router is Sagemcom F@st 3864 by Optus ISP (Australia).

  First of all, I put the D7000 in Bridge mode I did these steps:

  1. replace the IP LAN 192.168.0.100

  2 disable DHCP

  3. connect the LAN port to the main router Lan port

  Internet connection wired and wireless on the same device but other wireless devices has failed

  To remedy this, I made another choice, allowing point-to-point wireless access in the advanced settings of the D7000. I followed the instructions from this link

  http://KB.NETGEAR.com/app/answers/detail/A_ID/24104/~/how-do-i-change-my-Nighthawk-router-to-AP-mode...

  I put dynamiccaly = wireless internet cable success but peripheral does not have an ip address

  No idea how to fix wireless? I'm not very experienced

  Thank you!

  I just fixed it just now. For AP mode, connect the LAN port of the main router to the WAN port on the D7000 (not LAN to LAN). I wish I thought to it much sooner.

• Errror: The certificate chain was issued by an authority that is not approved. connecting to a wireless access point

  I can't understand the process of certificates, by connecting a pc wireless access point that is authenticated by the radius server, im keep having this error "the certificate chain was issued by an authority that is not approved." do I need to set a certificate on the pc?

  Hello

  1. What is the version of the operating system that you are using?

  2. What is the exact full error message?

  If you use Windows 7 follow the link below:

  http://Windows.Microsoft.com/en-us/Windows7/view-or-manage-your-certificates

  http://Windows.Microsoft.com/en-us/Windows7/certificates-frequently-asked-questions

  You can also contact your ISP for more information.

  Hope the above information is helpful.

• Issues with Dell desktop computer wireless and D-Link wireless network card. Only able to get wireless access by checking "Use Windows to configure my wireless network". This kind of file sharing impossible.

  original title: can't see the computer on wireless internet!

  I hope that's not too much detail, but I would like that the sequence of events to be clear...

  I have a Dell desktop computer that's probably six or seven years now.  It did not come with a wireless card, so I bought a DLink router and combo card wireless, install both with the DLink software.  It works beautifully.

  Later, we through my rep AT & T DSL, I got a Motorola modem/router with wireless capabilities.  I had plugged directly on my computer Dell desktop and moved to a Dell laptop DLink wireless receiver.  No problems.

  The Dell laptop is dead and the DLink receiver has not been used for a long time.  Family of my daughter moved to our place, and I have connected his desktop computers and laptop to wireless internet, using the Windows Connection Wizard.  Still no problem.

  I got a new ASUS laptop, I also linked using the Windows Wizard.  STILL no problem.

  Now, here's the problem comes.  I moved the Dell desktop computer, connected the DLink wireless receiver to it and I am able to get wireless access ONLY when I go into the properties of PC, click the wireless networks tab and check the "use Windows to configure my wireless network" box.  Then I can connect correctly, but I don't see this computer on my wireless network.  Bad luck... because I want to be able to access share files.  When I try to connect using different assistants of Windows, I get a message to the effect that, if I used another software to connect to the program, I can't use the Windows Wizard.

  So, what can I do to remove the original configuration of DLink completely and to connect to my wireless network using the wizards in Windows?  I uninstalled the software of DLink, but it seems to have no effect at all.

  BTW, Dell desktop computer is running XP, office computer of my daughter is running VISTA, and two laptops are equipped with Windows 7.  I can see all the computers on the network with the exception of the original Dell desktop computer wireless.

  Any help would be appreciated!

  Hi Joe and DonnaLoth,

  The network will have to be changed to allow the computer Windows XP join a workgroup.

  How to change a computer name, join a domain, and add a computer description in Windows XP or Windows Server 2003

  You can also read the following article.

  Networking of computers running different versions of Windows

• A WRT160N V3 can be used as wireless access point.

  I have an AT & T's broadband router.  A WRT160N is connected, so I now have Wireless N capabilities.  I have a second WRT160N I want to put in my living room as a point of access, so I can connect my BluRay player and video stream.  How can I configure the second WRT160N as access point?

  Thank you in advance,

  Andrew

  Topic 1. Yes, you can use your second WRT and put in place as a second access point to your network. First of all, unplug the second WRT to your network and wire a computer in one of its LAN ports. Open the web interface at http://192.168.1.1/ on the main configuration page, change the address LAN IP of 192.168.1.1 to 192.168.1.2 and disable the DHCP server. Save the settings. Unplug the computer and connect the cable to the first router on one of the second router's LAN ports. Do not use the internet port of the second router! Now you can use the wireless access point in the second router as access point additional for your network.

  For a wireless roaming the two Wrds with identical wireless settings (SSID, wireless security, etc.) and don't forget to enable the SSID broadcast. Only the channel assignments should be different. Different channels spaced at least 5 avoids duplication of canals. Now your laptop can connect to your network via either WRT and internet through the first WRT. It must also be able to move between the two Wrds without losing the connection.

  Re 2. Because the WRT160N has only the ethernet 10/100 ports a CAT5e cable should do. Of course, you can consider getting a better cable, for example a cat6 for future enhancements to your network. It depends on how much effort it is necessary to replace the cable later if you decide to go for gigabit ethernet on your local network.

• Troubleshoot the bad connection with router (WRT350N) and Point (WAP4400N) wireless access

  Hi all

  I have a problem and will apprecaite all the help I can get. I think I will find an answer here.

  I have a small network, Linksys WRT350N (wireless router) attached to a modem and then connected to a desktop computer and with 3 wireless laptops connected to the router. All 3 are really great to work and access the internet very well.

  Currently, I have the need to expand the network to 3 floors, so I bought 3 Points of access wireless of Linksys (WAP4400N).

  I ran 3 cables CAT5e cable from the router and which ends individually all 3 floors, the top floor is less than the router 40meters. With the cables that came in their boxes, I connected the APs to the router and I have correctly set up the 3 Access Points with them attached to the router, all 3 works perfectly (I can access wireless internet via 3-point). However when I take the points of access to the upper floors and connect cables cat5e APs no longer work but connect after some time with the message "limited connectivity".

  Why can I connect when the APs are connected to the ground floor via a short cable that came in the box and not when it is connected to put cables from the ground floor to the upper floors but rather make the "LIMITED SERVICE" message and cannot connect to the internet.

  Also if I connect the cat5e cables directly to a laptop computer on all the floors, I can connect to the internet (the work of cables fine when connected directly to a laptop computer), but when it is connected to the connection of the APs has failed and I begin to see strange IP addresses from the APs.

  Oh, one more piece of important information: when I connect cables CAT5e cable on all floors direct to a laptop I can connect to the internet (the work of cables very well when it is connected directly to a laptop) but when connected to the failed to connect APs and I begin to see strange IP addresses from the APs.

  HEPL!

  I think I have the forum a status report on my post. As I mentioned in my last post, the problem has been as a result of lower cable at my provider. The network is running smoothly. Has been in place since last week when I replaced the lower quality cat5e cable cat5e cable.

  A Board here please be careful and make sure you complete the cable. A bad end can lead to connection problems I discovered in this case when my team confidence terminated cable incorrectly.

  Network up to & operational: Linksys WRT350N router without wire + 3 Linksys Wireless Access Points WAP4400N + Modem providing access to (1 computer (cable), 6 workstations (wireless), & 5 laptops (wireless).) Network to grow shortly.

  Thanks to everyone who helped make this project a reality.

• The WRT600N can connect to a wireless access point?

  I installed Windows 7 on my desktop and I was not able to install all types of Linksys wireless adapters.  I decided that linking an my WRT600N wireless access point in the other room and hardwireing the office to the access point, would be a good idea.  I'm probably going to connect it to a Net WTG624 Gear, which is capable of acting as an access point and you connect to another router.  The question is, can the WRT600N you connect to and use the internet and the local access and, ultimately, on the Office of cable?  I feel that it is one of the most stupid questions, I ask myself here again, but I'm not sure.

  EDIT: I'm sure it's called Wireless Bridge.

  Thank you

  Zach

  Hello Zach,

  The WRT600N can connect at the point of access, and vice-versa. I have a WRT600N home and have the same model of NetGear as access point (what are the chances?) and it works fine, although I do miss the 5 GHz as the Access Point is only 2.4 Ghz 802.11 g Standard.

  I hope this helps!

• There is no communication between devices that are connected to the Linksys WAP4410N Wireless access point?

  Hi all

  I have deployed the new Linksys WAP4410N Wireless Access Point and it works fine. Laptop which is connected to the AP may be able to access the internet. It can communicate with AP and also the gateway IP (IP Router) but it is wireless devices are not able to communicate with each other. In the case of peripheral LAN can communicate with wireless devices. Cannot able to share files between wireless devices.

  Please help me solve this problem. Wat could be the problem here. Stage of Wat I have to take to eliminate this problem.

  Advance thanks.

  Thank you and best regards,

  Chandhuru.M

  Hi, my name is Eric Moyers. I am a network Support Engineer in the Cisco Small Business Support Center. Please use the Forums to Post community of Cisco.

  The title of security without thread/how do you have isolation set up wireless?

  Insulation wireless (SSID) on the inside must be disabled to allow the computers associated with the same SSID to see and transfer files between them wireless

  Thank you

  Eric Moyers. : | :. : | :.

  Cisco Small Business U.S. STAC Advanced Support Engineer

  CCNA, CCNA-wireless

  866-606-1866.

  Mon - Fri 09:00 - 18:00 (UTC - 05:00)

  * Please rate the Post so other will know when an answer has been found.

• configuration cisco air-ap1142n-a-k9 problem wpa2 wireless access point

  HI people,

  I am brand new to Cisco Wireless, just that I bought new wireless access point air-ap1142n-a-k9 cisco, try to configure the configuration of wpa2 for security reason, but impossible to configure in any mode security. So my AP is currently no security / encryption mode.

  Could someone can help and suggest me I will appreciate if I get all documents, so the security problem can be solved.

  Concerning

  Sanjeev

  OK great

  ----------------------------------------------------------------------------------------------------------------------

  Be sure to note the correct answer and mark the thread as answered

• Various Questions about wireless access controller

  Help me please with these fundamental questions about the role of the access (AC) wireless controller.

  Assume that the access controller and Access Point are connected via IP:

  -Wireless frames sent to AP to acre; include the original MAC header (on the way to wireless access)?  If Yes, is there a Cisco AC gets to fill the WLAN and LAN it is plugged (which means that it outputs as ethernet frames as if they were issued by Mobile Stations).

  -Is the AC necessarily the default gateway for mobile stations? I guess not. But it is possible the default gateway?

  The Cisco AC can function as a DHCP relay?

  The AP creates a tunnel to the controller. All IP traffic from the AP to the controller will address the AP source and dest IP to the interface of the Manager of the AP on the controller. The wireless client traffic is encapsulated inside this tunnel. When it hits the controller the CAPWAP is removed leaving the customer's original package to be sent to the local network through the controller.

  The controller should not be the default gateway for wireless clients because it is not a router. Think of it as a device that converted into wired wireless traffic.

  Normally, the controller acts as a proxy DHCP. Once the customer has joined a WLAN, the controller sends the DHCP packets to the DHCP server on behalf of clients such as the IP address of assistance normally configured on the router for cable customers. You can also configure the controller to act as a DHCP server for wireless clients.

• Beginner needs help with Aironet 1131 G Wireless Access Point

  I have a new Cisco Aironet 1131 G wireless access point.  It takes an IP address and I can ping this address.  However, I can't access it via the graphical user interface based on the web or the CLI.  I preformed reset.  Any suggestions would be greatly appreciated.

  Thank you.

  Hello

  I can't access that means? you are not able to go to the CONFIG T of the CLI prompt? and if you are in the same subnet as the AP, are you not able to open to the top of the GUI? If you are not able to then, with the command 'show version' on the AP CLI and see if your image is "RCVKW8". If so you will need to convert the same IOS using the method below.

  http://www.Cisco.com/en/us/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap22-trouble.html#wp1038660

  Let me know if that answers your question...

  Concerning
  Surendra
  ====
  Please do not forget to note positions that answered your question and mark as answer or was useful

• Error IRQL_NOT_LESS_THAN_OR_EQUAL when I try to connect to wireless access points

  I get this error IRQL_NOT_LESS_THAN_OR_EQUAL whenever my wireless adapter is turned on or I re - enable after I disabled it to stop the BSOD happen at startup.

  Here are the scenarios in which it happens:
  (1) when I turn on the laptop and the wireless adapter is enabled; It gives the blue screen and restarts.
  (2) once it has been restarted since the first scenario, I have trying to move from a point of wireless access to the other.
  (3) the wireless adapter was disabled before closing, when I turn on a connection attempt, but it shows all the available connections and I try to solve problems, blue screen back again.

  Other information:
  I do not have any material change. I use the Windows 8 operating system. I use the HP Envy m4.

  Also, when it starts later, my screen remains black at any time from 1 to 5 minutes.

  I find that I use my PC because of the frustration of the far less.

  EF

  These accidents were related to the corruption of memory (probably caused by Kaspersky).

  Run these two tests to check your memory and find which driver is causing the problem.  Launch auditor.  You need not run memtest again unless you want to.

  If you are overclocking anything reset by default before running these tests.
  In other words STOP! If you don't know what it means that you're probably not  
  
  
  
  
  1-Driver Verifier (for full instructions, see our wiki here)
  
  2-Memtest. (You can learn more about running memtest here)

  
  

• After running Thinkvantage System Update, unable to connect the wireless access point

  I've recently performed Thinkvantage System update for updating various programs/drivers on my T61p.  I've updated the V5.12 access connections.  In addition to this I was required to update driver V1.52 power management and functionality of the shortcut key for

  V2.10.0002 (two of them were the most recent available).

  After these updates, I can connect is no longer to any access point wireless that worked before this update.  I have tried to reinstall earlier versions of Access Connections, but still couldn't connect to wireless access points.

  ANY help would be appreciated.

  OK, problem solved.  I found that when I ran last weekend system update downloaded and installed an incorrect driver for my wireless hardware.  I installed the correct driver and now the connection to a wireless access point works.

  Certainly, I don't understand how/why not update system would be to download and install an incorrect driver.  VERY FRUSTRANT and TEDIOUS!