Static DNS problems

Similar Questions

• EA6200 IS NOT WITH THE HELP OF STATIC DNS

  I had the EA6200 weeks and set up out of a NVG589 of TA &T; has not worked well, no problem at all using the AT & T modem as the DNS server.  I just noticed that there is an update of firmware for this model, up to 1.1.41.164830; so, I got the router install it.  But now I was making errors on all my devices, saying that the DNS server is not responding.  I have sailed on the section of 'Connectivity' and the 'Local network' tab and my static DNS is as it was before the update of the firmware.  But when I connect a device to the router, the network parameters show that she tries to use the network personalized ID I have install the router, rather than the static DNS that I've locked in the router settings.

  The only way I am able to get online and write this message from my laptop now is because I had to go into CMD and put the static DNS for the laptop computer, manually, to the IP address of the modem from AT & T.  DHCP should be handling this according to my settings, but it's not.

  If anyone has experienced this before? Is this a firmware issue? Should I go back or understand this?

  before you go back, try a factory reset by pressing the Red reset button until it restarts, then cut off the power. After 10 seconds the power turn on and when it is completely started config it from scratch and it should be ok. Of course this will eliminate all the settings you had including the password which will then return to "admin" be aware of this before you start.

• WRT54GS static dns issue

  Hi friends.

  I'm trying to configure a local DNS server to manage domain names local only to the small office for our servers. I have the DNS works correctly (set the local machines and using the dns of your ISP if this is impossible). so I put the ip of the DNS server in the field 'Static DNS 1' of the configuration of the router. 2 other static dns fields are empty.

  the problem is that the router always uses the ISP as the primary dns server and my local dns server as secondary. I check this in two places. first of all, if I go to the 'status' tab, DNS 1 shows the ISP server while DNS 2 shows my local DNS server. Then, if I connect to the device wirelessly with a linux machine, the /etc/resolv.conf file contains the IP addresses of name servers in the wrong order.

  can someone tell me why the router is disobey my settings?

  Thank you very much.

  You have a static IP address provided by your ISP or just static DNS addresses, your router's Internet Connection Type must be set to the static IP address and you should have by default the IP address, subnet mask, gateway and addresses entered DNS... If you entered just the DNS addresses it won't work...

• Why static DNS server address round get the unable to download updates 8024402C problem in WIN7?

  I got a work around for the unable to download problem error 8024402C updated on a new laptop WIN7 Starter running.  I get regarding the size of the update and starts to download, but nothing comes down.  The solution is to change the DNS settings of default for a manually configured DNS server, for example 4.2.2.2.  It works, but I wonder why, and what is he moving?

  The auto setting worked when I was in the United States connecting via a LAN in the hotel but not here at home in AUS, where the settings auto search for an address DNS 192.168.1.1, my router ADSL/2.  All other functions like Skype, Adobe updated, download of MS shop, all work very well using 192.168.1.1.  Also my XP Home PC, all use 192.168.1.1 and they get the updates without any problem.

  -What is someone able to explain why?

  Thank you

  Hi ascidiens,

  The 0x8024402C error codes typically occur because there is an incorrect character in substitution of proxy settings. Basically, it's something to do with the proxy of your connection settings network and which can be overcome by changing the DNS settings in manual.

  Bad adjustment System (DNS) domain name of your network connection may also cause this error. Update Windows servers are accessible through DNS servers configured for Internet access. If a local DNS server has changed for some reason, the Windows Update client isn't able to find and connect to the Windows Update server.

  I would like to know if refer to a Microsoft article to work around this problem by changing the settings default for a manually configured DNS server DNS (Domain Name System).

  I would say to you to follow the steps mentioned in the link below for the complete solution of the problem

  0x8024402C error code when you try to install updates on Microsoft Update or Windows Update Web sites

  http://support.Microsoft.com/kb/900936/en-us

  Windows Update error 8024402C

  http://Windows.Microsoft.com/en-us/Windows7/Windows-Update-error-8024402C

  Thank you, and in what concerns:

  Ajay K

  Microsoft Answers Support Engineer

  Visit our Microsoft answers feedback Forum and let us know what you think.

• Static NAT problem with PIX501

  Hi all

  We have problems with our PIX firewall. We have configured PIX 501 with static NAT for our Web server. Here's the running configuration.

  6.3 (4) version PIX

  interface ethernet0 car

  interface ethernet1 100full

  ethernet0 nameif outside security0

  nameif ethernet1 inside the security100

  pixfirewall hostname

  domain ciscopix.com

  fixup protocol dns-length maximum 512

  fixup protocol ftp 21

  fixup protocol h323 h225 1720

  fixup protocol h323 ras 1718-1719

  fixup protocol http 80

  fixup protocol rsh 514

  fixup protocol rtsp 554

  fixup protocol sip 5060

  fixup protocol sip udp 5060

  fixup protocol 2000 skinny

  fixup protocol smtp 25

  fixup protocol sqlnet 1521

  fixup protocol tftp 69

  names of

  access-list 101 permit tcp any host x.x.x.26 eq www

  access-list 101 permit tcp any host x.x.x.26 EQ field

  access-list 101 permit udp any host x.x.x.26 EQ field

  pager lines 24

  Outside 1500 MTU

  Within 1500 MTU

  IP address outside x.x.x.28 255.255.255.248

  IP address inside 192.168.90.1 255.255.255.0

  alarm action IP verification of information

  alarm action attack IP audit

  location of PDM 192.168.90.0 255.255.255.0 inside

  history of PDM activate

  ARP timeout 14400

  Global 1 interface (outside)

  NAT (inside) 1 0.0.0.0 0.0.0.0 0 0

  static (inside, outside) x.x.x.26 192.168.90.3 netmask 255.255.255.255 0 0

  Access-group 101 in external interface

  Route outside 0.0.0.0 0.0.0.0 x.x.x.25 1

  Route inside 192.168.1.0 255.255.255.0 192.168.90.2 1

  Timeout xlate 03:00

  Timeout conn 01:00 half-closed 0:10:00 udp 0: CPP 02:00 0:10:00 01:00 h225

  H323 timeout 0:05:00 mgcp 0: sip from 05:00 0:30:00 sip_media 0:02:00

  Timeout, uauth 0:05:00 absolute

  GANYMEDE + Protocol Ganymede + AAA-server

  AAA-server GANYMEDE + 3 max-failed-attempts

  AAA-server GANYMEDE + deadtime 10

  RADIUS Protocol RADIUS AAA server

  AAA-server RADIUS 3 max-failed-attempts

  AAA-RADIUS deadtime 10 Server

  AAA-server local LOCAL Protocol

  Enable http server

  http 192.168.90.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  SNMP-Server Community public

  No trap to activate snmp Server

  enable floodguard

  Telnet timeout 5

  SSH timeout 5

  Console timeout 0

  Terminal width 80

  : end

  the problem is the configuration, we are unable to access the web server both inside and outside the network.

  All input will be greatly appreciated.

  Kind regards

  udimpas

  activate icmp backtrace and then ping the x.x.x.26 of the internet. the output should be as below:

  3363574:-out ICMP echo request: ID = 21834 seq = 1202 length = 80

  3363575: ICMP echo request: external untranslating: inside: 192.168.90.3

  3363576: ICMP echo-reply from the inside: 192.168.90.3 ID = 21834 seq = 1202 length = 80

  3363577: response to ICMP echo -: translate inside: 192.168.90.3 out:

  by doing this, you can 1. Check the nat 2. If the server responds to the internet.

  do not forget to allow incoming icmp:

  access-l 101 permit icmp any one

• PIX - static NAT problems

  I'm doing a static route to xxx.242.139.164 to 192.168.1.13 and open ports 25 and 443. I am at a loss for what I missed to make this happen. I would also like to open the ICMP traffic or at the least response to echo so I can test the IP addresses and that doesn't seem to work either.

  PIX config attached .txt file.

  Thanks for any help!

  Hi Comoms,

  This is your problem:

  (1) here say you do not NAT traffic.

  NAT (inside) 0-list of access inside_outbound_nat0_acl

  inside_outbound_nat0_acl ip access list allow any xxx.242.139.160 255.255.255.224

  (2) then you use it for the static NAT.

  public static xxx.242.139.164 (Interior, exterior) 192.168.1.13 dns netmask 255.255.255.255 0 0

  (3) it's totally fake, first u say don't not NAT traffic, try you NAT, it. How will it work?

  (4) even if uou help with ACL, it won't work.

  (5) Please check your routes n NAT ACL, NAT STATIC, once again.

  HTH

  MAR

• Internet/DNS problems in a NAT Windows Server guest domain

  Guys, I'm sorry if someone posted a similar question before, but I couldn't find everything concerning my problem using the tool of research or surfinf nets.

  I have a domain controller Windows Server 2008 R2 running in a Vmware Workstation 7.1.6 / Windows 7 Enterprise x 64. I use the NAT option for the network, because I need to use this virtual machine to several different networks and a domain controller needs a fixed IP address. The DNS is correctly configured to forward and reverse and the nslookup returns the IP address and the host name of the guest.

  The problem is that I can't connect to Internet in Virtual Machine, if I configure a fixed IP address (I am disabling the DHCP of VMware service at the moment). If I change in dynamics and start the VMware DHCP service, I don't have any problems.

  I looked at the gateway, the DNS and the mask subnet values provided by the ipconfig/all command when the server uses a dynamic address and the server if setuped values of static. It did not work.

  Anyone have a tip for this desperate man?

  Because the domain controller is also running the DNS server, I guess that DNS serer entries in the client IP settings point to the guest himself!

  If you are able to ping to Internet addresses by its IP address, you may need to configure the DNS server on the domain controller to transfer DNS queries for other areas to the (usually 192.168.xxx.2) NAT gateway for proper name resolution.

  André

• Weird DNS problem - solves Alias but not CNAME

  I use the DNS server role on Windows Server 2012 R2 on a physical machine on my home network.

  3 of my 5 machines are working properly and I can solve real host as alias names, but on 2 other machines, I can't resolve host names real (with Ping) even though I can still resolve alias - which seems really odd to me.                              .

  .10 - server 2012 (physical) R2 - both Alias and CNAME ping. (Displayed IPv4).

  .20 - server 2012 (virtual) R2 - both Alias and CNAME ping. (Displayed IPv4).

  .21 pings - 2012 R2 (virtual) server - CNAME, Alias (displayed) ipV4 does not ping.  Nslookup can resolve CNAME.

  .22 pings - 2012 R2 (virtual) server - ipv4 (displayed) Alias, CNAME also Pings but displayed ipV6

  .99 - Windows 7 (virtual) - Alias pings (display ipV4), CNAME not not ping.  NSLookup can resolve CNAME.

  All of the above machines are members of the same domain and that you have a single DNS server assigned (. 10)

  Given that 3 of the 5 machines are able to resolve the names, I have to assume that the DNS server is configured correctly.

  The computers seem to be set up exactly the same way.

  In all pings/research, I used the fully qualified host name and the fully qualified domain name.

  This could be the cause and how can I solve this problem?

  Thanks in advance to anyone who answer.

  Jim

  Ask in the forum Windows Server:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• All computers on a network cannot browse a specific external site - Possible DNS problem?

  Hi all

  The categories are too vague hope so I'm in the right forum... I have IE8, Windows 2008 R2, Question of DNS...

  We migrated from Windows 2000 to a Windows 2008 R2 domain 2 months ago. There has not been all problem reports since then and I'm to understand that all of their sites they are functioning normally, have been finding work subsequently... Now, the strangest thing is that all the sites that they want to go to all work properly with the exception of this specific site (www dot careerbuilderdotcom) so far.

  Checked the PING WWWdotCAREERBUILDERdotCOM

  (in case of failure may be due to the blocked ICMP) several computers and it does solve one of their IPS (208.82.7.50), indicating the DNS works and solve correctly... Tested accessing this site in particular, many computers and fails this site only. Tested also the computers outside the network to access the site in question and that they can browse correctly indicating that this is NOT the site...

  Checked entered DNS and restart the DNS service without result. Does DNSFLUSH on all of the computers in question and are still unable to access this site.

  It seems not to be a DNS issue. Can anyone provide additional lighting at the entrance and knowledge to solve this problem?

  Hello DASNetSys1

  If the suggestions provided by Ing. Ladislav Cermak do not solve your problem then please return the question in the Windows Server forum from the link below. Thank you.

  http://social.technet.Microsoft.com/forums/en/winservergen/threads

• Using a Vista laptop, connects to the internet, but will not load page. DNS problem.

  Hello.

  I use a Toshiba laptop with Windows Vista Home Premium 64-bit.

  I just have a modem and use a router. I have a network cable (cat 5) connected to my laptop and the modem. I have log-on internet and it connects. But when I open Google Chrome, IE9 or Firefox I can not load a web page. Google mentions something about the DNS cannot be found and DNS_Probe_Finished_No Internet.Frefox says server not found.

  I click on the Menu start - Connect To - I am logged in. I already typed my password in the command prompt and appropriate the pppoe connection/address (I use ADSL).

  I talked to my ISP and we tried to do certain things. But nothing works. On their end, it shows that I am connected. But I can't browse the internet. We tried to have the DNS and IP address for ipv4 set to obtain automatically and I put 2 numbers of DNS in manually once the settings have been changed to the favorite servers and DNS auxiliary, or worked.

  Using command prompt, the DNS has been emptied. It did not help. The modem has been reset the ISP location. I also recreated and set up a new network connection.

  My office is using the same pppoe information. I can freely browse the internet and I use Windows Vista Home Premium 32-bit. I was also shown to be connected simultaneously with both machines, but that the Office can go.

  I do not have Windows Update the laptop since on April 2016. It has not been used and the battery was empty. I tried to turn off the laptop several times, but nothing works.

  Y at - it suggestions to solve this problem? At that time perhaps a re - install will work.

  System Restore worked. I will run the updates and see what happens.

  I think it was a program that I uninstalled in programs and features.

  It's also useful information for this post: https://answers.microsoft.com/en-us/windows/forum/windows_7-networking/unable-to-connect-internet-dns-error-windows-7/72040e27-7a87-4f6f-88d6-9d158da38de8

  1.

  Note

  • You must open a command with elevated privileges prompt to complete the following steps. For more information, see command prompt: frequently asked questions

  1. Click the Start button.

  2. In the search box, type command prompt.

  3. In the list of results, right-click Guest, and then click Run as administrator.  If you are prompted for an administrator password or a confirmation, type the password or provide confirmation.

  4. At the command prompt, type ipconfig/flushdns.

  2.

  Start - Search programs and files
  Type "Command Prompt".

  Right-click in the program file that appears above the run as administrator.

  ipconfig/flushdns

  ipconfig/registerdns

  ipconfig/release

  ipconfig / renew

• Cannot log on to internet DNS problem: _

  I have 4 desktops and a laptop. both are running windows vista 64-bit and a 32-bit vista, an another windows xp. The laptop is windows 7 32 bit. All the computer are related to a home network. My window problem 2 64 bit vista and the laptop does not connect to the internet. The vista 32 bet of the window and the window and the window xp. The wireless network card displays a green globe. I got a dns socket error message load. How to load dns management< our="" is="" there="" an="" other="">

  This is the aspect of the sholud confoguration TCP/IP.

  Compare the good thing with one that does not.

  On the State of intellectual property.

  TCP/IP and its variables usually look like this.

  Right-click on the wireless network connection card, select status, details and see if she got an IP address and the rest of the settings.

  Typical TCP/IP status looks like this.

  http://www.ezlan.NET/Win7/status-NIC.jpg

  Description is the data of the card making.

  The physical address is MAC of the card number.

  The xx must be a number between 0 and 255 (all xx even number).

  YY should be between 0 and 255

  ZZ should be between 0 and 255 (zz all the same number.)

  The date of the lease must be valid at the present time.

  * Note 1. IP that starts with 169.xxx.xxx.xxx isn't valid functional IP.

  * Note 2. There could be an IPv6 entries too. However, they are not functional for Internet or LAN traffic. They are necessary for Win 7 homegroup special configuration.

  --------------------------
  Can you please send the information in the topics that are posted on the details screen (copy from the list below and paste it into a new message, type the information on your computer)...

  Description...

  Active DHCP...

  IPv4 address...

  IPv4 subnet mask...

  IPv4 gateway...

  Server DHCP IPv4

  IPv4 DNS server

  Jack-MVP Windows Networking. WWW.EZLAN.NET

• Primary DNS problem - constantly loss of Internet connectivity

  I've had this problem for some time now and I have not yet found a solution.

  I use a laptop Toshiba A215-S7422 (Vista). He has been nothing but a pain to operate, many errors and problems. But, I shouldn't use a Toshiba anyway...

  It loses Internet constantly. I have to keep diagnosing the problem, and it's always a primary DNS error. I use 2 other computers and they work fine, so I don't think it's my network.

  Go to the website of the manufacturer of your router > make sure you have the latest Firmware in Vista for it.

  Go to the website of the manufacturer of your computer/notebook > drivers and downloads Section > key in your model number > look for it last network adapters Vista drivers > download/install the.

  http://Windows.Microsoft.com/en-us/Windows-Vista/troubleshoot-network-adapter-problems

  Troubleshoot network adapter problems to Microsoft link above.

  Try without commitment TCP/IPv6:

  If you still have internet connection probs, one thing to try is the separation of the TCP/IPv6 (which is done by going to network connection > right click > properties > it uncheck > OK.)

  http://digitalmediaphile.WordPress.com/IPv6-how-to-unbind-from-a-NIC-in-Windows-Vista/

  See you soon.

  Mick Murphy - Microsoft partner

• Static noise problem Dell Inpiron 15 (7559)

  Hi all

  I noticed a noise static backgroung very disturbing coming from speakers of my Inspiron 7559. Noise active time avery I start multimedia content and turns on a few seconds after the extinction of the audio.

  In safe mode, the problem is always present and does not turn off.

  I have the latest version of each installed driver and I've updated the BIOS to the latest version.

  Tried to turn off the subwoofer, downgrade driver, uninstall and reinstall, the bios update to re - install but nothing seems to work.

  I'd appreciate if you could help.

  Thank you

  Hello. See the FAQ Audio choppy / jump. Advice on the i7559 are in 1 article.

• SonicWALL NSA 3600 6.2.2.1 - 14n and Sonicwall Mobile Connect for MAC DNS problems

  Hello

  I wonder if anyone has seen this problem. I just upgraded my NSA3600 to version 6.2.0 to 6.2.2.1 - 14n and now none of my MAC OS x clients that use the Sonicwal Mobile Connect application has no DNS. You can test by IP and use NSLOOKUP to find the records dns, but if you try to ping or access what either by its name it does not work.

  Everything worked perfectly before the upgrade to 6.2.2.1

  Thank you for this information, but it was not useful in this case because everything worked until I upgraded from 6.2.0 to 6.2.2.

  I just got got off the phone with Sonicwall support and there is a bug in the 6.2.2.1 - 14n and they gave me with a firmware fix. version 6.2.2.1 - 14n-HF156864-1n and everything is in working order.

• Could not connect to the internet, DNS problem

  Problem with the DNS system solves not addresses
  have tried the following

  netsh int ip reset

  netsh winsock reset
  netsh interface ipv4 reset
  netsh interface ipv6 reset
  ipconfig/flushdns ipconfig/release ipconfig/renew
  dns (8.8.8.8, 8.8.4.4) google DNS change
  in the dsl router dns change
  tried to reinstall google chrome
  Internet works on internet explore x 64 only (built in IE8)
  Update Internet Explore later, cannot access the internet now

  ---------------------------------

  Screenshots

  ---------------------------------

  Digital ip = google.com 120,28 thingy

  Can ping google.com on cmd and digital ip |  http://i.imgur.com/cXD8hBD.jpg

  tab of google chrome net internals events |  http://i.imgur.com/wnfAEOX.jpg

  Google.com Firefox |  http://i.imgur.com/W9BhLDM.jpg

  Firefox digital ip | http://i.imgur.com/I69LXd6.jpg

  ipconfig/all |  http://i.imgur.com/dA3I7gN.jpg

  net internals chrome google dns tab | http://i.imgur.com/ediPJet.jpg

  Google chrome net internals tab tests ip digital |  http://i.imgur.com/pbI1Zze.jpg

  test of google chrome net internals tab for google.com. http://i.imgur.com/WQ4rXCy.jpg

  Google chrome google.com | http://i.imgur.com/hNFW3vm.jpg

  running win7 ultimate x 64 sp1

  AMD a4-6300 apu with 3.70 GHz graphics Radeon (TM) hd
  4 GB OF RAM
  I hope I gave enough information to answer

  Adobe Flash Player can be updated, BitDefender may be updated,
  Applications can receive updated information but cannot update
  It has been almost a week since the last response.

  I also disabled my Firewall

  Edit = I accidentally fixed, I don't know how but my problem is now solved