Stop 0x0000008E Message loading Vista
I receive the following stop message when you attempt to load Vista: 0x0000008E (0XC0000005, 89623110, 0x8039907C, 0x00000000 0 x). I checked the BIOS and there's nothing obvious. Anyone can it shrink down? Thank you.
You can have a device with the wrong drivers or some other conflict. Check the Device Manager by going to start / find and type Device Manager and then clicking on the icon of this results. Double-click all elements with a red x or yellow! -those are devices to problems that must be fixed. Go to web sites of the manufacturer or the supplier of the computer to the latest Vista-compatible drivers and download and install. You can check if you have any problems of compatibility with the Windows Vista Upgrade Advisor to: http://www.microsoft.com/windows/windows-vista/get/upgrade-advisor.aspx and you can check your hardware devices for compatibility to the Windows Compatibility Center to the: http://www.microsoft.com/windows/compatibility/.
You can also be infected by the malware. To correct this problem download, install, and run the following two programs: http://www.malwarebytes.org/mbam.php and http://www.safer-networking.org/en/index.html. You can also try a free trial of Pandasoft (www.pandasoft.com). Before you download pandasoft, uninstall all anti-virus program you currently use (because the installation and execution of two simultaneously can cause conflicts, freezes and all sorts of problems). Once you have uninstalled your current AV program, download, install, update and scan using Pandasoft. I think you might be amazed at how much she notes that other software missed. Once complete, uninstall pandasoft and re - install your current AV program (unless you decide to spend that I did when I tried about 4 years ago).
Let's see if these options to correct the problem before seeking other solutions.
Good luck and I hope this helps. Lorien - a - MCSE/MCSA/network + / A +.
Tags: Windows
Similar Questions
-
I have a Dell computer with a 32-bit version Vista Ultimate factory loaded. Service Pack 1 is loaded. I tried to load Vista Service Pack 2 several times by using the following procedure and it does not load.
-From Microsoft technical support I click Download (using a cable modem) and click on the file to run. The file MB 475 downloads in about 5 minutes.
-Click on install Vista Service Pack 2 and it starts to install
-After about 10 minutes, a message appears "installation was not successful 800F081F error Code. A system error not install the service pack. Please download and run the tool to "Check for System Update Readiness". »
-J' I download system analysis tool and start the installation.
-Get a message "Installation update for Windows (KB947821) update 1 of 1"
-After a long time, a message appears saying that the Installation has failed with an error Code 800706BE.I repeated this process several times and always get the same result.
My McAfee security software and spyware blocker is disabled during this processThe update is not installed successfully, you receive a message, and the computer restarts when you try to install an update in Windows Vista
http://support.Microsoft.com/kb/949358See also the post of 'Response' in this discussion partners: http://social.answers.microsoft.com/Forums/en-US/vistainstall/thread/ad5159b6-edc7-4c45-842a-c8197aec3e07
========================
Free unlimited installation and compatibility support is available for Windows Vista, but only for Service Pack 2 (SP2). This support for Windows Vista Service Pack 2 (SP2) is valid until November 26, 2009. Availability of support chat or messaging differs depending on your location. Go to http://support.microsoft.com/oas/default.aspx?prid=13014&gprid=582034 & select appropriate category (i.e., download problem;) Installation problem; Problems after installing a service pack). ~ Robear Dyer (PA Bear) ~ MS MVP (that is to say, mail, security, Windows & Update Services) since 2002 ~ WARNING: MS MVPs represent or work for Microsoft
-
STOP STOP 0x0000008e error error messages appear after trying to install Windows XP on the new drive
Original title: Stop error 0x0000008e error displayed after trying to install Windows XP on the new drive
STOP 0x0000008e error. Also setupdd.sys - address F740DFEA base at F73EC000, Datestamp41107c8f. After trying to install Windows XP on a new hard drive. Never been in the BIOS. A bit afraid to change much, but it is said that the caching and shadowing should be turned off and boot into Safe Mode, but I cannot get Safe Mode because there is no OS on the drive. Also, he wants to know if I want to install Windows XP to a partition on the disk. I looked at other readers, and there is a partition, so I think I should. Any information would be appreciated. "Just an old fart."
Hello
See the following article: error message "STOP 0x0000008e" during the installation of Windows XP
-
Units media center crashes everytime I open a program recorded Tv or watch live TV. After an installation of factory with discs with the PC, I have received, I am unable to set up the media library. It crashes when I'm testing involved in the installation program. The error message is the same every time and is as follows:
Stop: 0x.0000008e (0xc000005, oxbd296765, oxafd26b28) ox0000000
Address NV4_displ.dll BD296765 @ BD0120000 day basic stamp 47311f16
I thought after the installation of the plant the problem would be resolved
Hi Kathy P._935,
I suggest you follow the article in the Microsoft Knowledge Base and check if it helps.
You may receive an error message on a Windows-based computer: "STOP 0 x 00000050" or "STOP 0x0000008e"
http://support.Microsoft.com/kb/903251
I hope this helps.
-
error message stopping me from loading mcafee
error message stopping me from loading mcafee as well as I can not load the 3 pack
Hello PamelaReeves straw,
What is the error message you get when you try to install McAfee? You need an internet virus protection if you do a search on the internet. If you do not have an antivirus program, Microsoft has a product, that you can download for free. Click on the link below to download and install Microsoft Security Essentials.
http://www.Microsoft.com/security_essentials/It provides protection for your PC in real time at home that protects against viruses,
spyware and other malware. It's a free download from Microsoft that is simple to install, easy to use and always up to date so that your PC is protected.Try to download to your desktop and install from their. If you get an error message and cannot install, please let us know.
Sincerely,
Marilyn
-
STOP: 0x0000008E and system restore
Hello world
My Windows Vista recently blue armored to Midway through the boot process, see the details of technical error following:
STOP: 0X0000008E (0C 0000005, 0 X 00000000, 0XB71D5A48, 0X00000000)
The error always appears during startup in normal mode (i.e. after the entry are the PW Windows and during the loading of the incons office etc.). My machine never blue armored in safe mode.
Don't know if it is a hardware or software error, I did a restore of the system for three weeks before.
The system seems to work fine now.
All hunch that it was a mistake to orsoftware material? What can I do to avoid blue screen in the future?
Your ideas are appreciated.
Thank you very much
Simon
Hello
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65--------------------------------------------------------------------------------------------------------------
Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See methods of update driver generic in the next message.
BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens. (If necessary)
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
It comes to my convenience store generic bluescreen:
Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
This would help. Such as ITC and 4 others entered at the bottom left. And another error
information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
http://www.NirSoft.NET/utils/blue_screen_view.html
hangs and displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker
(SFC.exe) program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
Unable to start - STOP: 0X0000008E
before you start the vista shows, shows the blue screen...
What should I do?
the error code is
STOP: 0X0000008E (0XC0000005, 0X819E0343, 0X866309A8, 0X00000000)
Thanks in advance
original title: problems loading vista
Read the posts by spirit MVP in the following thread on the Blue Screen of Death. They should help you solve your problem. http://social.answers.microsoft.com/Forums/en-US/vistahardware/thread/8cd8362e-7d06-46fb-afd7-84d54b6a8ea7.
In addition, since it is probably a problem with hardware driver or device, you can consult the following article on troubleshooting of hardware:http://www.elephantboycomputers.com/page2.html#Hardware_Tshoot.
I hope this helps.
Good luck!
Lorien - MCSA/MCSE/network + / has + - if this post solves your problem, please click the 'Mark as answer' or 'Useful' button at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Blue screen - STOP: 0x0000008E
I got a blue error screen that lists the following information:
Problem: Blue screen
6.0.6002.2.2.2.0.768.3 OS version
Locale 1033 ID
ICC code 1000008e
BCP1 C0000005
81FF03D4 BCP2
BE0C2C5C BCP3
BCP4 00000000
Version of the OS 6-0-6002
Service Pk 2
768-1 productFiles that describe the problem:
C:\Windows\Minidump\Min.011410-01.dmp
C:Users\Owner\AppData\Local\Temp\WER-123833-0.SysData.XML
C:Users\Owner\AppData\Local\Temp\WER14F6.tmp.version.txtThe message said I may not have sufficient disk space and disable BIO memory options and something to do with caching. My battery was insufficient in time, so not that of course that has nothing to do with it. My battery needs to be replaced as well, since it does she take his load for more than 30 minutes. In any case, I don't know what to do or who call for this problem. I run on Windows Vista Edition Home Premium. I've already fried a laptop after 1. 5 years, the current one is 2 years old. I'd appreciate the help. Thank you
Hello
Power problems can cause strange things, however if the system is connected to a/c which should not be a problem.
Two main causes of this blue screen video drivers and BIOS - check with system manufacturer site for
View of the adapter (video) and BIOS, then on site of the manufacturer of the device for the last video. There may be other drivers
in order to check there. DISABLE the auto-pilot plant as those who are older and if updates Windows suggests
a pilot just HIDE. Antivirus is another possibility.See methods of update driver generic in the next message.
BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
- 0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved .chk , which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
It comes to my convenience store generic bluescreen:
Here are a few ways to possibly fix the blue screen issue. If you could give the info from the blue screen that would be
Help. Such as ITC and 4 others entered at the bottom left. And any other information such as STOP error
codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death' crashes, and
http://www.NirSoft.NET/utils/blue_screen_view.html
Displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged drivers, video drivers in particular, but there are other causes.
You can follow these steps in the Safe Mode if necessary or the command prompt Vista DVD or Options of recovery if your
system installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible driver problems).
Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, 3rd party keyboard and
smile, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob - bicycle - Mark Twain said it is good.
-
Error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000).
I have error Stop: 0X0000008E (0XC0000005, 0X820371A7, 0X9F10E91C, 0 x 0000000). I did the F9 Diagnostics and no error found. Also, I tried to remove the DVD and replace the video card, but no improvement. However, Windows starts normally in SafeMode only. Thanks for supporting.
Product ID: 89578-OEM-7332157-00061
Hello
Specifying your version of Windows and other information would help help us to you.
How to ask a question
http://support.Microsoft.com/kb/555375-----------------------------------------------------------------------------------------------------------------
Check this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files.
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65===============================================================
BCCode: 8th 0x0000008E is the same as 0x1000008ETwo main causes of these blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See the methods of update driver generic and verify the implementation of driver verifier in the next
Message.BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.
0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens.
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
Here are a few ways to possibly fix the blue screen issue. If you could give the blue screen
info that would help. Such as ITC and 4 others entered at the bottom left. And all others
error information such as codes of STOP and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
hangs and displays information about all accidents of a table - free
http://www.NirSoft.NET/utils/blue_screen_view.htmlBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do mode if necessary safe or the Vista DVD command prompt or
Options recovery if your system is installed by the manufacturer.How to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlYou can try a system restore to a point before the problem started when one exists.
How to do a system restore in Windows 7
http://www.SevenForums.com/tutorials/700-system-restore.html-------------------------------------------------------------------------
Start - type this in the search box-> find COMMAND at the top and RIGHT CLICK – RUN AS ADMIN
Enter this at the command prompt - sfc/scannow
How to fix the system files of Windows 7 with the System File Checker
http://www.SevenForums.com/tutorials/1538-SFC-SCANNOW-Command-System-File-Checker.htmlHow to analyze the log file entries that the Microsoft Windows Resource Checker (SFC.exe) program
generates cbs.log Windows Vista (and Windows 7)
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Windows 7
http://www.SevenForums.com/tutorials/433-disk-check.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmInstallation and update of drivers to 7
http://www.SevenForums.com/tutorials/43216-installing-updating-drivers-7-a.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting Vista Blue Screen, error of JUDGMENT (and Windows 7)
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
Startup Options recovery or Windows 7 disk repair
How to run a startup repair in Windows 7
http://www.SevenForums.com/tutorials/681-startup-repair.htmlHow to start on the System Recovery Options in Windows 7
http://www.SevenForums.com/tutorials/668-system-recovery-options.htmlHow to create a Windows 7 system repair disc
http://www.SevenForums.com/tutorials/2083-system-repair-disc-create.htmlHow to do a repair installation to repair Windows 7
http://www.SevenForums.com/tutorials/3413-repair-install.htmlI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">
-
STOP: 0X0000008E (0XC0000005, 0X805662D1, 0XB38CDA04, 0X00000000)
Tonight, my computer shuts down with a blue screen with a message saying that there was a problem with Windows, more this stop message...
STOP: 0X0000008E (0XC0000005, 0X805662D1, 0XB38CDA04, 0X00000000)
I have managed to restart in Mode safe for this post, but am not all that computer warned to manage a technical difficulty. Is there a simple solution that I can use for this problem, or is a trip to my computer that required doctor?
I have not loaded new software in the past few days and have now uninstalled the latest program installed, just in case.
When I tried to send an error report, it wouldn't send it due to a problem.
Any ideas?
Thanks in advance,
Andrea
It can help to look at the files minidump against accidents with a debugger.
Can you zip the minidump in the C:\Windows\Minidump folder files and (provide link) available via Windows Live SkyDrive or similar site?
The following link has information about the use of Windows Live SkyDrive:
If you have problems to compress the minidump files copy the minidump files to another location such as a folder on the desktop
In addition, you do not necessarily have compress the minidump files, you can download one at a time.
-
I get the blue screen error - error - Stop 0X0000008E
-Stop error 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000)
Hi I get the blue screen error - error - Stop 0X0000008E (0xC00005, 0XC000005, 0X08244c8b, 0XBA50B58C, 0 X 00000) and cannot use the pc in safe mode. I have XP - OS. I really don't want to reformat the HARD drive and you want to avoid reinstalling as much as possibleHi aromaveda,
· Have you made changes on the computer?
Follow these methods.
Method 1: Follow the steps in the article.
You receive a random "0x0000008E" error message on a blue screen in Windows XP
http://support.Microsoft.com/kb/827663
Method 2: Follow these steps:
Step 1: Start the computer in safe mode and check if the problem persists.
A description of the options to start in Windows XP Mode
http://support.Microsoft.com/kb/315222
Step 2: If the problem does not still in safe mode, perform a clean boot to see if there is no conflict of software like clean boot helps you eliminate software conflicts.
How to configure Windows XP to start in a "clean boot" State
http://support.Microsoft.com/kb/310353
Note: After completing the steps in the clean boot troubleshooting, follow the section How to configure Windows to use a Normal startup state of the link to return the computer to a Normal startupmode.
After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.
(a) click Start, run.
(b) type msconfigand click OK.
(c) the System Configuration Utility dialog box appears.
(d) click the general tab, click Normal startup - load all services and device drivers and then click OK.
(e) when you are prompted, click on restart to restart the computer.
Method 3: Follow the steps in the article to check the drive for errors.
How to perform disk error checking in Windows XP
http://support.Microsoft.com/kb/315265
Note: If bad sectors are found in the hard drive, then it could try to fix this particular sector. If you have any data on that, it can get lost.
-
Stop: 0x0000008E (0 x 80000004, 0x806EDAE1, 0xA82E2708, 0x00000000)
I get this message * Stop: 0x0000008E (0 x 80000004, 0x806EDAE1, 0xA82E2708, 0x00000000) when I play world of Warcraft. It happens that I load the game and is about to show on screen. Sometimes it dosent happen but it will be possible that when note, ive tried updated my bios by from what I can tell its place even todate all the driver I know are up to date, please help this really frustrating.
At least, it's different, and you know that you have the latest drivers from Intel.
If it were me, I would compose a message which included the two parts (General information and the video portion) of your latest msinfo32 (you can remove your personal information such as user name) and a description of the problem with the exact error message you see (not paraphrase or "similar to") and WoW you trying to get to work and who post to the support of WoW and the community of users of the web page WoW. People are very passionate about WoW and they have probably seen this before. Don't forget to register if you can be notified of responses.
I then copy and paste this nice message and paste it into the community from Intel as well.
Search on Google, it seems that other people are able to get WoW to work with your Intel stuff, but I don't know how do it and have no resource to try to reproduce it - other people who have already done well.
-
Original title: * stop: 0X0000008E (0X9F266F91, 0X942F5F64, 0XC0000090, 0x00000000)
I have xp professional sp3 on a laptop that I bought for the College and try to use Dragon Naturally Speaking v.10. I have the program loaded and am able to open it and to do the two micro checks, but when I try to start the windows training part stops and gives me the above stop error message. I used v.9.5 DNS on an older desktop with xp with sp2 and never had any problems. What is the difference and can something be fixed so that I can use v.10 on my laptop?
Hi Markiepoo,
Method 1:
You try to perform a clean boot. A clean boot to check if startup item or services to third-party application is causing this issue.
You can read the following article to put the computer in a clean boot:
http://support.Microsoft.com/kb/310353
If your problem is resolved after the clean boot, and then follow the steps mentioned in the article above to refine the exact source.
After you have used the boot is a way to solve your problem, you can follow the steps to configure Windows XP to start normally.
Method 2:
If you're still having problems, then try to uninstall and reinstall the program.
a. Click Start, click Control Panel and then double-click Add / Remove programs.
b. in the currently installed programs, click the program you want to remove and then click on remove.
c. If you are prompted to confirm the removal of the program, click Yes.
d. restart the computer and reinstall the program.
For more information, see the following article:
How to change or remove a program in Windows XP
http://support.Microsoft.com/kb/307895
Also check out the following link and check if it helps:
Hope this information is useful.
Jeremy K
Microsoft Answers Support Engineer
Visit our Microsoft answers feedback Forum and let us know what you think.If this post can help solve your problem, please click the 'Mark as answer' or 'Useful' at the top of this message. Marking a post as answer, or relatively useful, you help others find the answer more quickly.
-
Blue Screen iastor.sys, STOP; 0x0000008E (0xC0000005, 0x828490B8, 0xB96DA758, 0x00000000)
iastor.sys - address 828490B 8 physical memory base to @8280B 000, Date Stamp 48054343 - Crash Dump, dump - the disk of 100 I can work only in Mode without failure, but I can't print or scan that I need to do. Someone can help me.
Hello
Looks like you need to update iastor.sys:
iastor.sys = Intel Matrix Storage Manager driver - see System/card mother Maker and manufacturer of chipset.
This driver could perhaps was pushed to the fault by other programs such as Symantec/Norton.This driver is extremely difficult to install if you need system or the manufacturer of the motherboard (for custom
bed systems) help but you could also ask on their forums (if any).Also check the Intel downloads audit AFTER with the system/motherboard manufacturer...
Intel downloads
http://Downloadcenter.Intel.com/Intel Matrix Storage Manager - do not forget to check DATE and set for the version of Windows and chipset
http://Downloadcenter.Intel.com/SearchResult.aspx?lang=eng&keyword=%22matrix+Storage+Manager%22More help on installing iastor.sys here (System Maker/card mother Maker first consult and use that as a last resort).
============================================================
More troubleshooting if necessary:
Pick up the pieces after a computer crash
http://Windows.Microsoft.com/en-us/Windows-Vista/picking-up-the-pieces-after-a-computer-crashCheck this thread for more information using BlueScreenView, MyEventViewer and other methods
to troubleshoot the BlueScreens - top 3 responses (+ 1 other).We can analyze the minidumps if make you it available to the SkyDrive or another file
sharing sites (such as MediaFire). If you have problems to download the copy of minidumps
for the office or in the Documents folder and download them from there.ZIP or download the content of the C:\Windows\minidump
Use SkyDrive to upload collected files
http://social.technet.Microsoft.com/forums/en-us/w7itproui/thread/4fc10639-02dB-4665-993a-08d865088d65--------------------------------------------------------------------------------------------------------------
Two main causes of this blue screen video drivers and BIOS - check with the system manufacturer
Site for graphics (Video) card and BIOS, then on site of the manufacturer of the device for the last video. It may be
other pilots to check there. Disable the installation of self as those who are older and if
Updates Windows suggests a pilot just HIDE. Antivirus is another possibility.See methods of update driver generic in the next message.
BCCode: 8th 0x0000008E is the same as 0x1000008E
Cause
Bug KERNEL_MODE_EXCEPTION_NOT_HANDLED control is a very common bug control. To interpret it, you must identify which exception has been generated.
Common exception codes are:
0 x 80000002: STATUS_DATATYPE_MISALIGNMENT indicates that an unaligned data reference was encountered.
0 x 80000003: STATUS_BREAKPOINT indicates that a breakpoint or ASSERTION was met when no kernel debugger was attached to the system.
0xc0000005: STATUS_ACCESS_VIOLATION indicates that a memory access violation has occurred.
Solve the problem
If you do not have to debug this problem, you must use certain basic troubleshooting techniques:
- Make sure you have enough disk space.
- If a driver is identified in the bug check message, disable the driver or check with the manufacturer for driver updates.
- Try changing video cards.
- Check with your hardware vendor for updates to the BIOS.
- Disable the BIOS memory options such as implementing caching or shading.
If you plan to debug this problem, you may find it difficult to get a stack trace. Parameter 2 (the address of the exception) should identify the driver or function that caused the problem.
If you do not know the specific cause of the exception, consider the following:
- Hardware incompatibility. Ensure that all new equipment installed is listed in the list of the products tested Microsoft Windows market.
- Service driver or defective peripheral system. A chauffeur service or defective peripheral system could be responsible for this error. The hardware problems, such as BIOS incompatibilities, conflicts of memory and IRQ conflicts can also generate this error.
If the verification of the message bug list a driver by name, disable or remove that driver. In addition, disable or remove drivers or services that have been recently added. If the error occurs during the startup sequence and the system partition is formatted with the NTFS file system, you may be able to use Safe Mode to rename or to delete the faulty driver. If the driver is used as part of the start-up procedure of the system Safe Mode, you must start the computer by using the Recovery Console to access the file.
If the problem is associated with Win32k.sys, the source of the error may be a third-party remote control program. If this software is installed, you can remove the system startup service using the recovery and then Console by removing the offending system service file.
Check the system log in Event Viewer for additional error messages that might help identify the device or driver responsible for control of bug 0x1E. You can disable the cache in memory of the BIOS to try to resolve the error. You must also run the diagnostics of material, especially the scanner memory, which provides the manufacturer of the system. For more information about these procedures, see the manual of your computer.
The error that generates this message may occur after the first reboot during Windows Setup, or after installation is complete. A possible cause of the error is lack of disk space for installation and the system BIOS incompatibilities. For any problems during the installation of Windows that are associated with lack of disk space, reduce the number of files on the hard disk drive target. Search and delete temporary files that you do not have to have, files hidden Internet, application backup files and files saved.chk, which contain fragments of files on disk scans. You can also use an another hard disk drive with more free space for the installation.
You can solve the problems of BIOS by upgrading the version of the system BIOS
BCCode: 8th 0x0000008E is the same as 0x1000008E<-- read="" this="">
* 1151.html? order = date http://www.faultwire.com/solutions-fatal_error/kernel-mode-exception-not-HANDLED-0x0000008E-=============================================
Look in the Event Viewer to see if something is reported on those.
http://www.computerperformance.co.UK/Vista/vista_event_viewer.htmMyEventViewer - free - a simple alternative in the standard Windows Event Viewer.
TIP - Options - Advanced filter allows you to see a period of time instead of the entire file.
http://www.NirSoft.NET/utils/my_event_viewer.html-------------------------------------------------------------------------
Also this, so you can see the probable bluescreens. (If necessary)
Windows Vista restarts automatically if your computer encounters an error that requires him to plant.
http://www.winvistatips.com/disable-automatic-restart-T84.html-------------------------------------------------------------------------
It comes to my convenience store generic bluescreen:
Here are a few ways to possibly fix the blue screen issue. If you could give the info to blue screen
This would help. Such as ITC and 4 others entered at the bottom left. And another error
information such as the STOP codes and info like IRQL_NOT_LESS_OR_EQUAL or PAGE_FAULT_IN_NONPAGED_AREA and similar messages.As examples:
BCCode: 116
BCP1: 87BC9510
BCP2: 8C013D80
BCP3: 00000000
BCP4: 00000002or in this format:
Stop: 0 x 00000000 (oxoooooooo oxoooooooo oxoooooooo oxooooooooo)
Tcpip.sys - address blocking 0 x 0 00000000 000000000 DateStamp 0 x 000000000It is an excellent tool for displaying the blue screen error information
BlueScreenView scans all your minidump files created during 'blue screen of death '.
http://www.NirSoft.NET/utils/blue_screen_view.html
hangs and displays information about all accidents of a table - freeBlueScreens many are caused by old or damaged, in particular the video drivers drivers however
There are other causes.You can do without if needed fail or the Vista DVD or recovery command prompt mode
Options if your system was installed by the manufacturer.This tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxYou can try a system restore to a point before the problem started when one exists.
How to make a Vista system restore
http://www.Vistax64.com/tutorials/76905-System-Restore-how.html-------------------------------------------------------------------------
Start - type this into the search-> find COMMAND to top box and RIGHT CLICK-
RUN AS ADMINEnter this at the command prompt - sfc/scannow
How to analyze the log file entries that the Microsoft Windows Resource Checker
(SFC.exe) program generates in Windows Vista cbs.log
http://support.Microsoft.com/kb/928228The log can give you the answer if there is a corrupted driver. (Says not all possible
driver problems).Also run CheckDisk, so we cannot exclude as much as possible of the corruption.
How to run the check disk at startup in Vista
http://www.Vistax64.com/tutorials/67612-check-disk-Chkdsk.html-------------------------------------------------------------------------
Often drivers up-to-date will help, usually video, sound, network card (NIC), WiFi, part 3
keyboard and mouse, as well as of other major device drivers.Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htmHow to install a device driver in Vista Device Manager
http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.htmlHow to disable automatic driver Installation in Windows Vista - drivers
http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx-------------------------------------------------------------------------
How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart
quit unexpectedly
http://support.Microsoft.com/kb/958233Troubleshooting, STOP error blue screen Vista
http://www.chicagotech.NET/Vista/vistabluescreen.htmUnderstanding and decoding BSOD (blue screen of death) Messages
http://www.Taranfx.com/blog/?p=692Windows - troubleshooting blue screen errors
http://KB.wisc.edu/page.php?id=7033-------------------------------------------------------------------------
In some cases, it may be necessary.
The Options or Vista recovery disk Startup Repair
How to do a startup repair
http://www.Vistax64.com/tutorials/91467-startup-repair.htmlThis tells you how to access the System Recovery Options and/or a Vista DVD
http://windowshelp.Microsoft.com/Windows/en-us/help/326b756b-1601-435e-99D0-1585439470351033.mspxI hope this helps.
Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">
-
Error blue screen: STOP: 0x0000008E KERNEL_MODE_EXCEPTION_NOT_HANDLED
original title: blue screen with the error: "STOP: 0x0000008E (0xC000001D, 0 x 82850572, 0x9E204038, 0x00000000)"»
Hello everyone,
It has been more than a week I tried to re - install my computer: ACER9802AWKMi after several months of support with blue screen apearing errors whenever there is more than one program open :-(
So I started with a recovery disk, but the problem was still there. The computer came with XP Home Edition and I got an upgrade to Vista (all original stuff) with all updates (SP1 and 2 and everything else updates)
Now, every time I go on the internet: especially no problem, but if I want to play a game (online) full screen, after a few minutes:
Yes: blue screen with messages such as
STOP: 0X0000008E (0XC000001D, 0 X 82850572, 0X9E204038, 0X00000000)
STOP: 0x0000007F (0x00000008, 0x8013F000, 0 x 00000000, 0 x 00000000) or
PFN_LIST_CORRUPT or
something with the memory of the BIOS (which I have to remove cache or mirror) witch I tried to do, but not found in the BIOS SetUp (when start PC press F2)Whenever I get another message :-(
I tried with FixIt, fact CHKDSK - CHKDSK F + CHKDSK F R
I have also run Everest to have all the necessary stuff... so if you need it...If anyone has a sollution, I would be very happy to hear it.
TX much
In the mean time brands more than 13,000,000 errors:(et toujours obtient plus élevé.) Of course I'm not every minute in front of my screen (sometimes I work too: the job from 9 to 5, you know)
Hi Sabine,.
This means that the RAM is broken or damaged. If you receive error messages, you can stop the execution of memtest86 +.
Ask someone who knew a little technical to open the laptop and check out how many RAM modules there. If it has a single module, buy a new RAM module.
If she has more modules, remove other modules, so that you don't have 1 module of RAM left. Now run the test for each RAM module again (only install 1 module at the same time) to check if all are damaged or 1.
If you have discovered how many RAM modules is broken, buy new RAM
André
"A programmer is just a tool that converts the caffeine in code" Deputy CLIP - http://www.winvistaside.de/
Maybe you are looking for
-
How to decrease the font size in safari?
The size of the police looking for google in safari is too large, there is not space to watch between the lines, how to decrease the size of the font? the zoom in and out does not work, the font remains the same size and the letters overlap. HELP PLE
-
Server standard SBS 2011 when adding computers to domain 404 file or directory not found error
I settup a SBS 2011 standard on the DHCP server running on the domain server because we use the router to distribute ip to the clients. When I try to add computers to the domain, I get an error (404 file or directory not found) on the client side. I
-
Error rundll32 "is not a valid integer."
every 5-10 seconds a message appears saying rundll32 "is not a valid integer. and even if I press OK it always comes back and he won't stop.
-
BB10 sdk 10.0.9.1673 problem, run the application on the device
I am facing problem by running the application on BB 10 alpha dev device after the installation of the SDK gold BB10question is attached to this post please suggest a possible solution for this problem
-
BlackBerry 8800 Smartphone unpredictable drains battery
Hi, my 8800 seems to be on a full charge for a few hours, then it will quickly drop the fridge for an hour or two, up to 50% or less. Sometimes, a night after a charge full in the afternoon, the 8800 is dead in the morning. What he receives from on