StorCenter px6 - 300 stuck d

Similar Questions

• StorCenter px6 - 300 d SNMP SNMP problem after FW update to 4.0.2.9960

  Hello

  We have a problem in PX6 - 300 d, after the upgrade from version 3.2.3.15290 to 4.0.2.9960, FW SNMP configuration. Ishmael of application allows us to manage matrices. After updating the FW one of storage, the application can no longer collect information. Notify know if there was no change of FW which caused this problem?

  SNMP parameters in storage, are equal, the difference in this version of the FW of storage.

  Thank you for your help

  Adias

  Hi adias.

  There is a newer version of the firmware. I recommend updating to the latest version to see if the problem persists.

  Firmware Version 4.0.8.23976 for px6 - 300 d

• px6 - 300 d stuck at 95%

  Hello

  Since the weekend, our px6 - 300 d seem to have a problem because I can not access it via the web console and Windows... So, I have to restart with the power button. But now, when it starts, it remains at 95% for hours and I can't access...

  They were not all the errors on the discs.

  Do someone has an idea of what's going on?

  Thank you for your help.

  Hi osimonazzi,

  Try to start the device without the attached network cable. When it reaches 75% then re - attach the network cable.

  If this does not work you can try operating the restraint system and reseating the HDDs.

  Is - this device still in warranty?

• PX6 - 300 d S/N remotly

  Hello.

  How can I get the serial number remotely (www, SNMP, SSH,...)?

  Feature: LenovoEMC2 PX6 - 300 d.

  Thank you.

  Hello janB4,

  You can not identify the serial number of the device remotely.

• PX6 - 300 d seems to be churning

  My px6 - 300 d seems to be churning, the hard drive light is darn near all of the time, I know that it is not locked on because only it twinkle from time to time, but not often, and I can feel the vibrating drives furiously. Is there a software or back door to give the visibility regarding if it is reconstruction or check if I can see what is happening?

  Hello Scott_H,

  The lights of storage on several of our NAS of rest continuously and flicker when the disks are being accessed.

  If you wish to contact support and have some material performed basic diagnostics, you can do so here:
  https://Lenovo-na-en.custhelp.com/app/ask/

• PX6 - 300 d - double Raid 1 is not possible?

  Hi guys, I hope I'm missing something, so I'm tender hand to support community. I've had a px6 for awhile now. I love. Works very well with VMWare hypervisors. I've been running a RAID 1 and a RAID 5 for over a year without any problems.

  Now, my needs have changed. I run 2 raid-1 matrices. I deleted my raid-5 array and don't see Ano option in the list to create another Raid-1. Why is this? I see raid-10, but not what I need. Just another Raid-1.

  In my case, I need to divide the disk IO system in another array of disks in raid1. Simply becoming the current Raid1 is not enough, because there a lot of requests for e/s which should not weigh down the second raid-1 array. I need raid1 because of the performance and the protection it offers.

  Can someone comment on the creation of another array of Raid-1? I hope that I don't need to buy another NAS compete for this task.

  Thanks for the tips!

  Figured it out. There is a bug in the GUI. Once you have 1 raid-1 array configured, there is no option to create an another raid-1 array. BUT, if you select a new table and set of raid-10, it can reset to raid-1 on the creation. I have now 2 tables separated from Raid1 created by doing it this way. They are NOT wiped off of mirrors raid-10.

• [PX6 - 300 D] Resource monitor - "access is denied. You must be a user admin to access this application. »

  Hello

  I get this error message when I try to open the monitor of resourse

  "Access is denied. You must be a user admin to access this application. »

  I use the admin account. Where could be the problem?

  Thank you very much in advance.

  Hello Steven,

  Thank you for your support. The problem has been resolved by reinstalling the software. It seems that the new version of the software is out - strange here was that my request for resource monitor appeared also to update in the update software tab.

  Thanks again.

• How to determine who has access to the training

  Hello

  I have an iomega StorCenter ix4 - 300 d set up as a network drive with several users who have permission to access. From time to time some of the scripts are unable to access one of the drives inside. For me, it seems that when that happens someone in my network uses extensively this player (the blue led continues to blink). Is there a way to determine who is using the drive or what resources are being accessed?

  Thank you very much for the help.

  Hi pegazik,

  The event log indicates if users log in to the device and make changes. There is not a way to show what is being accessed.

• failure in RAID 6

  I have NAS PX6 - 300 d with RAID 6, it records images from surveillance cameras this week one of the drives has failed and the cameras stopped working with RAID 6 should not continue to burn? the drive has been changed and now I can't access the shared folder

  PS. Update Firmware for NAS will lose my data that is in the files?

  Thank you

  I have it
  RAID it only protects data, but registration does not continue.

  Thanks for the help

• POS datastore NFS and network monitoring

  Finally, I decided to start my own thread about this.

  This is the message which I have added to another:

  Hello

  I installed POS for the first time yesterday at 13:00. The unit is sitting on a host in a vCenter which is in another network.

  Host has 4 network cards, one for the corporate network, one for a network isolated from the plant, vMotion and one other network isolated.

  Connected via NFS on a NAS that is in the same switch on 1GbE links.

  Has taken a backup of a virtual machine (which is sitting on another ESX cluster: same vCenter) yesterday during the night and all went well. Took 45 minutes to save it to the top of the first.

  But since the first minute of the installation of POS, I am interested in my network monitoring system and it shows me shards of data every 5-10 minutes sending input/output between the nas and esx... Actually vdp device sending and receiving in nas.

  It's almost to every time about 257 155 kbit/s every 5-10 minutes in the graph. Nothing else is followed (like vmware sensors or wmi from any kind. just snmp traffic from the port of the switch and a ping to the esx host)

  No other ESX shows this kind of traffic. If I look at the graph of sin, same thing, which brings me to the direction in which the matter is between the two.

  I did close to the bottom of the application, so I can really see if there is a problem with her or directly nas device-related...

  One thing I also noticed is the traffic fate vmnic0 for backup last night at 22:00 which is fine but immediately fell after 45 minutes of backup when finished. The strange thing is that the excessive traffic out of vmnic2 which is connected to the private network and has nothing to do with the POS. But as soon as I close the virtual machine appliance VDP graphic down and no problem at all.

  The last question is; Hell where traffic comes from and why it goes on the vmnic2 so that the virtual machine has nothing to do in this group of port!

  In fact, I think I'll go hang the nas in the same switch as the vmnic0, that I think about it... I guess that the traffic comes from vmnic0, but nas is hung in the same network as vmnic2 so it must jump over chips inside the esx host. But I wonder why he keeps returning 200 Mbps of data every 5-10 minutes for a period of 2 minutes, but maybe someone could enlighten us on that.

  This is the reason why I've seen traffic on both interfaces. Now, NAS is attached to the same switch on the network of the company as the ESX host that the device is sitting on.

  Virtual POS machine has 4 data warehouses:

  100 GB OS is on the SAN

  3 x 1 TB of data on the nas via nfs

  Host ESXi 5.5.0 build 2456374

  vCenter 5.5.0 build 2442329

  NAS is a Lenovo Iomega StorCenter ix4 - 300 d

  (I have not activated all along the way. jumbo frames no change)

  What is using a lot of bandwidth of the device? Is this normal? It is very moving stuff and I can't understand what it is!

  These fragments come from the backup last night? No was not even 80 GB total backup... should not be so long? Says complete backup and dedup 32 of 80 GB...

  Please if you could help that would be appreciated.

  Thank you.

  I think I found something here: the VDP CPU usage

  It seems that the reading device checks on the destination of the backup every 5 minutes (300 seconds) and it is a normal behaviour according to VMware.

  Thing is that 1.5 GB of data (in my case) every 5 minutes is not acceptable because it can modify the use of bandwidth.

  I connected the console to the VDP and applied to the order, but with the interval of 0.

  I found another post here: VDP now uses constant bandwidth even during the prohibition period

  They say that the available maximum interval is 3600 seconds which is an hour. It's better than 5 minutes, but it seems that the 0 parameter is accepted by the device and no error is reported.

  I will update more than a hour to see if it works because at first, I applied the 3600 and my graph shows changes applied.

  It is 08:20 here, so I'll be back after 09:30 to make sure that the last hour.

• Resolution scanner Officejet Pro 276dw stuck at 300 DPI max

  The maximum resolution of scanner is now a reason any stuck at 300 dpi (see image below).

  Some time ago I was able to analyze with much higher resolutions, but somehow, this has changed now and higher resolutions are unavailable in the menu more.

  How can I activate the sweep of the higher resolutions?

  

  Hi Casey_

  You can try to change the parameter indicating the feeder flat to see if you can change the DPI settings.

  Located in the bottom right of the software screenshot.

  I'm sorry, but to get your question more exposure I suggest posting in the trade forums since it is a printer. You can do so at http://h30499.www3.hp.com/hpeb/ .

  I hope this helps.

• Qosmio X 300 - no video output after the installation of Nvidia 9800 M GTX

  Hi again all,

  Now, I have all the parts for my X 300 to fix it back to normal. Heatsinked the new chip, everything installed correctly... And no output.

  No monitor and no external.

  Now, I'm really stuck.

  Any ideas?

  Thank you.

  Ideas? On what? What you have done wrong with your laptop? I mean how can we offer some virtual diagnosis?

  Please don t get me wrong, but are you authorized and approved?
  If you do all this as a hobby, I don t think we can help you with this. You will be lucky and it works or... simply bad luck. Something is obviously not done properly.

  Did you get the parts or parts already used nine?

• HP Jetdirect 300 x: updated HP Jetdirect 300 x (J3263A) without Web Jetadmin or HP Download Manager

  If you have a HP Jetdirect 300 x (J3263A exactly) with an older version of firmware, such that H.08.20, you may have noticed it is almost impossible to update. The HP Download Manager is supposed to be used to update the product to the latest revision of the firmware, but it does not work and gives an error. Similarly, the HP Webjetadmin software does the same. The two pieces of software uses the SNMP protocol. Newer versions of the firmware are supposed to be updated via FTP or HTTP, but if you're stuck with an older version such as H.08.20, you're out of luck on these methods. So how is one with an older firmware supposed to upgrade to the latest revision?

  After days of experimentation and dig through the documentation and forums, I found a solution! TFTP. This process is not documented anywhere to my knowledge (and believe me I looked!) so please read carefully.

  The first step is to set up a TFTP server. You can try setting up on Windows or Mac OS X. For the record, however, I tried to use the built-in Mac OS x and had no luck TFTP server. Your best bet is to use a Linux virtual machine or a live cd. I used Debian and tftp-hpa. I have no luck with tftpd.

  1. Machine Debian Boot
  2. Make sure you have an IP address that is accessible to the Jetdirect. To configure the IP address, follow the instructions here: https://wiki.debian.org/NetworkConfiguration#Setting_up_an_Ethernet_Interface. If you are already connected to a DHCP server, you should not do anything.
  3. Install tftp-hpa:
     $ apt - get install tftp-hpa
  4. Copy the firmware file to the tftp directory, in my case "300X_H0867.dld".
     $ cp 300X_H0867.dld/srv/tftp /.
  5. Give everyone read on the file permissions
     $ chmod a + x /srv/tftp/300X_H0867.dld
  6. Eventually, try to download the file from another computer on the network to check if it works (assuming that 192.168.1.1 the server IP).
     TFTP $192.168.1.1
     TFTP > get 300X_H0867.dld
     If all goes well and as the file downloads, you should be good to go!
  7. Telnet in the Jetdirect 300 X. If necessary, restore default values to enable telnet server and set an IP as shown here: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpj02738
  8. Once in a telnet session, run the following commands (assuming that the tftp server address is 192.168.1.1):
     TFTP-server: 192.168.1.1
     updated - file: 300X_H0867.dld
     upgrade
  9. Immediately after that hit upgrade and pressing on enter, you will get a message saying that the Jetdirect will begin the update and your telnet session will be closed.
  10. In a minute or two, then try to telnet in the Jetdirect. If all goes well, type ' / ' and press ENTER, and you should see that the revision of the firmware is set to the new version!

• IdeaPad 300 won't turn on (new)

  Hi, I bought a Lenovo Ideapad 300 - 15isk this weekend and he needed for work this week, but it's really frustrating, it's brand new, out of the box and it won't turn. I hear sounds and I can see the lights, so I know that the system works, but I'm stuck with a black screen. I wanted to make a "difficult start" but I can't even find the battery. Very disappointed so far...

  It seems that it is a fairly common problem from what I see in many forums. Since I don't have any answers on this community, I am a refund in store and probably buy another model from another brand.

• Pavilion mini 300-010 in: no display after starting in safe mode

  Recently (2 weeks) bought the Pavilion Mini Office 300-010 and was well before decide me Flex my curiosity.

  the office is connected to my monitor VGA Samsung using the HDMI-VGA connector since the release of funds has no VGA or DVI - I usage options.

  the part where my curiosity killed the cat, was when I decided to start the winodws 8.1 in safe mode and see what happens.

  pressing F8 did not help that the load of the OS had no delay (or maybe it's the UEFI BIOS) and so I decided to put safe mode with "a minimum without network option 'using 'msconfig'." Performed a reboot assuming I see safemode and all I got is a black screen. Noticing that the driver for the conversion of the display cannot be loaded in safe mode and now I'm stuck because I do not have a p LCD monitor that plugs directly into.

  I checked the monitor VGA just in case, and it seems to work very well with my laptop. . Done reboot "N"-number of times and the result is the same. ".

  is there a way to get out of safe mode without actually doing a HDMI compatible monitor by just using the keyboard?

  Hello @LogicMantra,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how your office is not able to display after starting in safe mode, and I'd be happy to help you in this case!

  To fix this, I recommend you to borrow an HDMI compatible monitor and update the drivers for your system this way. If this does not work, please follow this document on the computer starts up but screen remains blank (Windows 8).

  Please re-post with the results of your troubleshooting, and I look forward to your response!

  Concerning