Strange problems from CC 2014 UI Illustrator

Similar Questions

• Strange problem after moving from the virtual computer to a new data store

  I am migrating our VM existing (8 in total) a 'problem' RAID to a new table on a new controller and am having a strange problem. Here are the steps I took (host OS is Ubuntu 8.0.4 LTS x 64):

  (1) off the power the virtual computer from the Web interface

  (2) the directories created for each virtual on the new RAID array computer (in this case a RAID 10 array on LSI 9750-8i controller)

  (3) rSync used to copy the data from RAID1 to be RAID2

  4) has created a new data store on the new RAID through the Web Server of VMWare user interface.

  (5) removed VM of the inventory through the Web, their return, added user interface then choose files .vmx on new data store on RAID2

  They have all power save fine... but three of them are not accessible on the network. I can open a console in the Web Server of VMWare user interface and they all run normally... but I can't their ping or access the respective virtual machine Web GUI. It seems quite arbitrary that those who work and those who are not. In this case... the VM that don't work is a license Autodesk, a Squid proxy server and a VM of cactus. All three of these virtual machines are 32-bit Ubuntu Server VM (two 8.0.4 and a 10.0.4)... and are the only Ubuntu VM on this host. It must be signifigant but I'm not see how.

  If I delete these three virtual machines of the inventory again and add to their original location (on the RAID1) they light up AND work normally. A consultant that we were working seemed surprised, as he had also done this experiment with some of the older VMWare products. I don't see how it would be the physical location of the files of the virtual machine. Any ideas?

  We rely on the migration to ESXi soon but in the meantime, we get these a few VM out of this RAID array problem. I'm stuck.

  Depending on the application, it may be enough to reconfigure the IP parameters (they are very probably on DHCP now) for the newly detected virtual NIC.

  André

• CC CC libraries 2014/Yosemite Illustrator won't apply colors

  I have CC libraries implemented with shades of colors, the load library and works fine in other applications CC, but I'm not able to apply swatches from the library in Illustrator.

  All I have this problem or have a resolution?

  iMac/16 GB/OS X 10.10.3

  Creative Suite CC 2014

  In Illustrator, you can not handle spot colors in a library

• Problem with Indesign 2014 CC (Creative Cloud)

  I tried to install InDesign Creative CC 2014 (in Mac) compared to the clouds but the installation hangs in 17%... Check the logs shows me that there is a problem with the file.

  Here is a screenshot of the logs

  If this is correct, the text says that the file is corrupted...

  
  

  Note: This is the unique application that gives me problems... I installed Photoshop, Illustrator, Acrobat Pro, etc. without any problems.
  

  Any idea?

  

  try to bypass your cc app and see if that helps:

  If you follow the 7 steps you can directly download a free trial here: Adobe CC 2014 Direct Download Links: Creative Cloud 2014 Release. ProDesignTools

  If you have a problem from the download, you follow the 7 steps, or your browser does not accept cookies.

  the most common problem is caused by failing to meticulously follow the steps 1, 2, and/or 3 (which adds a cookie to your system, allowing you to download the correct version of the adobe.com site).

  failure to obtain this cookie translates into an error page displayed after clicking on a link on prodesigntools.com or initiates the download of an incorrect (e.g., current) version.

• Satellite Pro C850 - strange problem with LAN connection

  Hello world

  I just signed up on this forum because I hope you guys can help me with a really strange problem.

  I recently bought a Satellite Pro C850-1MX
  It came with Win8, but given that I don't really like Win8, I bought an additional Windows 7 Pro (64 bit) license and installed on the laptop.

  The problem I describe, also arrived on 8 to win, which makes it even more strange.

  As soon as I connect a cable to the RJ-45 port, Windows tells me, that the LAN connection is not connected.
  As soon as I unplug the cable, Windows starts looking for a network and actually found one!

  So, the only way to connect to my LAN cable is... I have activate the LAN connection, wait that it detects a network (without the cable connected!) and meanwhile to connect the cable to the network port.
  Now... If I disconnect the cable once again, Windows still shows its connected.

  I must say, that I am a Director of professional network for more than 10 years now, so I should know my systems, but this never happened to me before. Event log shows nothing, re-installing drivers did nothing either. IM quite confused here and I hope you guys can help me.

  Thanks for reading, and let me know if you need any additional info!

  Greetings from the Germany,
  Sandro

  Hello Sandro,

  To be honest I confused m.

  I would try to start talking about the drivers installed, since you changed the system for Win 7.
  All the network devices, such as card WLan and LAN card are properly recognized in Device Manager?

  As I m not wrong not the laptop was equipped with a network card Realtek-8111F (1000BASE-T/100Base-TX/10Base-T) and WLan RTL8723AE Realtek b/g/n card.
  If both should appear in the device properly Manager if you have installed the drivers correctly.

  2nd question:
  You said:
  > As soon as I unplug the cable, Windows starts looking for a network and actually found one!
  Are you sure that you speak of LAN and WLAN?
  For me it made no further since. If the network cable is unplugged, the notebook would connect to the WLan where WiFi is enabled.

• Strange problem with Toshiba Express Media Player on Satellite M115-S3094

  I am facing a strange problem in my Toshiba M115-S3094, which has been pre-installed with Windows XP Media Center edition and which also had the Toshiba Express Media Player.

  I had already done a clean install of Vista on it, and then I decided to go back to XP with my recovery DVDs. I did the same procedures of first installation Express Media Player to backup (that I did when I bought the laptop) and then installing Windows XP DVD de Toshiba Recovery XP.

  The steps included:
  1 deleted recovery Express media player disk partitions
  2. installed express media player
  3 extracted Xp Recovery DVD, by selecting 'Recover without changing the Partitions' (there is no expert mode)

  Everything was fine (i.e. installation)... But now, after the turning off my laptop I press the Express Media Center button, the logo "Express Media Player" appears on the screen after loading of closures of laptop for 5 seconds.

  I tried to open it again and again, but the logo is displayed for 5 seconds and then my laptop stop...

  Laptop works fine when I connect to windows by pressing the power button / stop.

  Can someone help me on this strange question... ?

  Hello

  The whole story is a bit confusing
  First of all, I would like to know if your laptop is already preinstalled with the Media Express Player and if you were able to use it on your laptop in the past.

  Now something about the Express Media Player installation;
  In order to use the media functions Express the Mediaplayer Express Recovery CD must be performed before performing the recovery from the recovery DVD-ROM products.

  In addition, on the HARD drive should at least 150-200 MB of free space available.
  This free space must be on the end of the HARD drive and there must be unallocated. To get these free space on party products 3rd HARD drive should be used as Partitions Magic 8.

  I m not 100% sure that on error ID system badly but maybe it corresponds to the DMI evil information stored on the motherboard. If we're not DMI, you will not be able to reinstall Express Media player using the recovery media express CD.
  In the DMI must be set properly the manufacturing: Toshiba, product name: for example by Satellite M115-S30

  Finally and most importantly, I found this thread useful forum on the Media Express recovery procedure:
  http://forums.computers.Toshiba-Europe.com/forums/thread.jspa?MessageID=51801쩙

  Could be useful for you!

• Strange problems on Satellite P30

  Hello
  Hope someone can help me that this laptop is causing me a massive headache

  The P30 for 2 1/2 years now, had my share of problems, DC have to be repaired and overheating due to the obstruction of the fan/radiator etc.

  a few months I ve noticed problems again with the domain controller, connection, works ok, but if you hit the laptop a little, it loses its charge and the amber light turns off and it extends the battery, the laptop must be turned off in so he can be charged. Also, there is a hissing/crackling noise from the charger when it is plugged

  I downloaded ATI Catalyst software a few days back and since then I ve had nothing other than problems, I got a mom.exe error and since then I have times m restarting constantly randomly, I formatted my system using the master CD, the laptop was returned to the factory settings, but 2 minutes in windows, I restarted, I formatted again and put an original disc of XP SP2 and who used to put a fresh xp on my laptop. But once I was doing restarted without any warning. Of course, I had installed my hardware from Toshiba disk drivers.

  Now my system is totally messing with my head, I can't get into windows without problem, I can surf the internet without problem, I tested a game for 5 hours last night (set of high spec) there was no reboot at all, and the computer ran fine. If I open windows media player and search for songs my computer restarts, I have tried to install software like nero and System Mechanic it restarts again, I watched a movie using windows media player and who ran late, its when its looking for songs it turns off, I do not understand is how random, I don't see the problem is the video card (games will work perfectly) and I do not think that the problem are a nuisance power because the game ran fine with the fans spinning, got a little hot, but that's normal I guess. It s mainly when I m access some files on my drive C: is when it restarts

  Please can someone help with this strange problem?
  Thanks in advance

  Oh 1 still a thing, I also have problems with my m * a UJ820S mat, when I connect to windows, it is not in my computer, if I remove the Bay and restart the machine, it appears and works fine until my computer is off again

  Hello

  I read all strange story twice and believe me, confuses the issue description
  I can't give you a solution to the problem, but I can try to make some suggestions
  To me, it looks like a motherboard problem

  Several years ago I also had a strange problem with my old no Toshiba laptop.
  The laptop always closes if I open the html files. But this happened only while the laptop was connected to the main power supply.
  It's very strange for me and the ASP could not believe that finally, the technician changed the motherboard and since this replacement everything runs great

  I think you should also try to contact the service provider in your country for detailed notebook verification.
  In your case, it s really necessary

• strange problem with Ericsson H5321

  Hello

  I have a strange problem with Ericsson H5321 on my X 230. Until a few weeks ago, the card worked perfectly as a modem (at least on Linux, so I guess it would be too much work in Windows). Unfortunately, a few weeks ago disappeared from the network manager modem connection. I checked that all the special device for this files still exist:

  $ because I in/sys/class / * / * {ACM, wdm} * / device/interface; echo-n "${i}: ';" $ Cat {i}; fact
  
  / sys/Class/TTY/ttyACM0/Device/Interface: H5321 gw Broadband Mobile Modem
  
  / sys/Class/TTY/ttyACM1/Device/Interface: H5321 gw Mobile broadband data Modem
  
  / sys/Class/TTY/ttyACM2/Device/Interface: H5321 gw Mobile Broadband GPS Port
  
  / sys/Class/usbmisc/CDC-wdm1/Device/Interface: H5321 gw management of mobile devices to wide band
  
  / sys/Class/usbmisc/CDC-wdm2/Device/Interface: H5321 gw Mobile Broadband USIM Port
  $ lsusb | grep Ericsson
  
  

  .. .and I also checked it works like GPS (at least kind of: it generates data on/dev/ttyACM2 NMEA streams, but cannot get a GPS fix even after 45 minutes with access to an open sky).

  Then I tried to run windows 7 and the card is visible in the "Device Manager", but there is also no possibility to create the GSM connection in the connection menu in the bottom right.

  I tried a new install of Windows 7, I tried to reset the BIOS (even with the removal of the battery backup), but still I can't force them to work again. My BIOS is fully upgraded BTW: the problem appeared during the use of 2.61 and I also tried with recently published 2.62.

  My cell phone is always on the extended warranty, but as modem bought in line with the basic configuration it was only covered by the warranty of 12 months has expired

  Today it came to my mind that, as the modem itself seems a little work (present, responsive GPS device) then maybe it's a SIM card reader that is actually damaged (which would explain a bit why the camera itself is present, but I can't create a connection). Can someone confirm or deny my theory? If it is valid, then I could still replace SIM card reader because it is part of the basic configuration.

  Thanks a lot for your suggestions!

  [Mystery solved: I managed to put the SIM card on a wrong side...;]
  [I hate myself so muuuuch;]
  ([btw: Lenovo could fix their SIM card reader, so there is only one possible way to put a SIM card using his corner of heart: it would have saved me 2 days of stress and an investigation;]) )

• Strange problem - Cluster of references

  Hello guys

  I had a strange problems using a cluster with references.

  How to reproduce the problem:

  -Open a white VI;

  -create two charts in the front panel;

  -in the block diagram, create references to two graphics;

  -connect these references to a package (not);

  -create an indicator across;

  -run the VI once;

  -Right-click on the beam indicator and change it to a control;

  -remove the references and bundle;

  -Select the control from the front panel, go to EDITION, CUSTOMIZE the CONTROL;

  -change the type strict def;

  -Save this order as Control1.ctl;

  -connect the control to a unbundle by name;

  -Right-click on the name unbundle and select one of the two graphs as an element (no matter that one select it);

  -Create a property node and feed its terminal of reference with the reference of the unbundle by name;

  -use of the 'Label.Text' property in the property node;

  -create a flag for the node of the property;

  -run the VI;

  -l' indicator will display the correct label for this chart.

  -perfect!

  If you save the VI and run again, fine.

  But... If you close it, open it again and run... you will get an error 1055 "object reference is not valid.

  Why it worked before closing?

  Find attached the VI and the control.

  Thank you

  Dan07

  Let see if I can answer before I start work.

  Do a quick experiment.

  Use Type casting to cast your Ref as a U32 and display this value on the public Service.

  Save the VI race she and the registration number on the FP.

  Mod the vi record close it open and run again. The number must have changed.

  That is the question facing you, ref number changes if you need one that is valid when you run.

  How do I;

  I use a motor of Action (see this nugget to learn what is a motor of Action) as servse as a GUI controller and allows me to get in refs where even I need them. The following is a case study.

  I first collect all th refs I need and combine them into a def type. I am pursuing a state machine to make the grouping if there are many.

  

  The clsuter group are passed to an Action controller GUI engine

  

  Inside Init, I check the referees to make sure that they are vlid. This has saved a lot of time wated no valid refs.

  

  If they were valid I cache the arbitrators.

  

  For major changes that require a lot of punching of GUI, I create Subvi to do the dirty work.

  

  Every time the ref to the GUI needs to other codes, I have a method that returns the arbitrators.

  

  The following is an example of an another VI using the MISTLETOE refs.

  

  I hope this helps,

  Ben

• Strange problem with my FPGA Code

  Hello

  I am running the following program, but I am facing a strange problem:
  -I can read all analog and digital input and write on the outputs analog (I measure the tension that I write on the map of the AO)

  - But the valves I have connected to the analog output, flashes a red light (which, according to the data, sheet means the electrical signal I send to them via the module AO is incorrect)

  -However, if I delete the ms and RMS block and do not make any average samples, but let all even (still two loops and two of the nodes separated from FPGA to e/s), the valves are operational and flash not a red light.

  I have a cRIO with four modules:
  -1. The (Mod1) AO cards
  -2. Map of HAVE it (2)
  -3. DI/O card (Mod 3)
  -4. Map to HAVE secondary (Mod4)

  I currently have two loops on the fpga all-in:
  -' Hand Loop (ML)': reads and writes I/O cards 1-3, with an expectation to 300us
  -'Top pressure sensors Loop (PACKAGE)' reads two HAVE the fourth module (Mod4), with no waiting

  These two loops are indicated in "fpga - part 1.png" and "fpga - part 2.png".

  The settings for the ms and RMS measures VI, as well as the façade are indicated in "fpga - part 3.png".

  The second loop uses 12002 ticks to run, the first loop use 160 ticks to run

  Previously, I had a similar problem which was fixed by setting the initial values indicated on the front cover for the analog output to the valves.

  Currently, I have not any target VI race and I'm only using fpga VI

  Any suggestions? Thank you!

  
  

• Strange problem with ASDM

  Hi, today we had a strange problem with one of our 5550. I worked through ASDM on it and all of a sudden I couldn't connect via asdm on the interface of management or inside interface. Nothing helps.

  When I connected with a vpn, then use asdm, it works. My ip on the network when it did not work was 1xx.xxx.81.235. When I use the vpn is a 1xx.xxx.55.1 from a different ip address. I can build a connection on the inside interface with asdm (with vpn).

  I tried closed and without stop the interface of man, that does not.

  It may be that the things asa, I am an intruder and dynamically blocks my netwerk range? If yes where can I find this info.

  Other users of our team had the same problem.

  I also checked the syslog nothing.

  THX,

  Marc

  Although I've ever experienced this myself, but if the running-config has not changed and worked before its possible that the ASA

  may have shunned your connection?

  To the CLI:

  # sh shun

  look if your IP address is present, if any make:

  # claire shun

  http://www.Cisco.com/en/us/docs/security/ASA/asa80/configuration/guide/protect.html#wp1058270

  More than likely it is do to a change to the running configuration, I would start by looking at a previously working with the gift of running-config running-config.

• Help! drop-down strange problem - mobile version

  Hi experts, I have a strange problem drop-down. Please look at: www.maikwollrab.com and click on the fist multipicture. on the following site, there are several images and vimeo links under the other. It is not possible to scrollup. If you try the page automatically rises again. cable. the strange thing is that, when only scroll you over the images (without the vimeo links) works. What can I do to avoid this?

  I got down

  Aside from the crazy number of pictures/videos on a single page, which makes scrolling not smooth, seems to work very well!

  

• Strange problem with universal theme, jQuery and APEX 5 on Windows 8.1

  I have a strange problem that makes me crazy. I get it whenever I need to run some jQuery or JavaScript in the new universal theme. This page is a good example:

  https://Apex.Oracle.com/pls/Apex/f?p=93000:600

  Whenever I click on the calendar icon it opens and closes immediately. This happens when I click on and release the quick mouse button. If I do it slowly, click it, wait a second and release the mouse button, it opens as expected. I did the inspection of javascript in the firebug debugging console and I can see that each action runs twice.

  On this page, you can debug:

  https://Apex.Oracle.com/pls/Apex/f?p=93000:16

  by pressing a button.

  I did some tests with some of my colleagues and discovered that this happens only on computers with Windows 8.1 running pages in Firefox or Google Chrome. IE works as expected.

  I invite participants in this forum to do a test for me, if they have one of the browsers mentioned and Windows 8.1. My tests were from two different laptops I (the two Windows 8.1) and also of a virtual machine on Windows 8.1. I was able to reproduce this problem on all three computers.

  I also did the same test with apex.oracle.com and with my local installation of APEX 5.0. They both behave the same.

  I can't reproduce this with applications having the old model like this:

  https://Apex.Oracle.com/pls/Apex/f?p=31517:215

  Thanks in advance.

  

  Denes Kubicek

  Brad, thanks a lot for the performance test.

  Talking with the main developers of the universal theme, this afternoon, we have now highlighted what we believe to be the cause of this problem. There's code in a universal theme that uses hammer.js and apply a logic of quick click on all the links and buttons, with a few exceptions closely. We believe that it is this code that may be responsible for these questions.

  Please hold fire for more such tests as requested previously, my apologies for any lost time do. We will follow on this thread with results as soon as we can.

  Thanks again for your help so far.

  Kind regards

  Anthony

• Very strange problem with quick mask

  Hoping someone can help me with a very strange problem that just started to happen when I enter the quick mask in PS CS5. Let me guide you through the problem.

  (1) I opened my image in PS, go in the Mode mask quick and 'paint' my image in translucent red with a brush (100% of opacity, brush, etc. normal mode).

  

  (2) once I fully painted my picture in translucent red, I leave the Quick Mask mode and the area outside the translucent red is selected. I hit M for the marquee tool, right-click on the picture I have just painted and choose 'Select inverse', which then selects everything within the translucent red area (note that I made this a million times over the years).

  

  (3) my image is now selected. In general, what I do now is cut (cmd + x) that selected the image and paste it into another canvas, generally where is my biggest project. Whenever I did it, the image cuts and fits exactly as it is seen and leaves an empty space in the original image. However, when I cut it now, it seems to cut a transparent version, leaving behind a transparent 'ghost' of the original image.

  

  (4) then when I paste the image cut in a new canvas, it is transparent as a default value.

  

  I checked the transparency of all the paintings, and they are set to 100%. As I already said, I cut from images of no solid media using the quick mask all the time and it's never happened before. In fact, I made this weekend and it has only just begun in the last hour, so I think I clearly something clicked or activated a parameter without realizing account!

  In considering this explanation, I hope someone knows what is causing my pictures to cut and paste transparent after that I used the quick mask. It certainly is driving me crazy!

  Any advice or assistance would be most appreciated.

  Thank you

  In your first screenshot the color of foreground in the Toolbox is not 100% black (RGB 0,0,0)

  Until you try the quick mask, press D to set the foreground on black (RGB 0,0,0)

• Hi, is it possible in 2014 CC Illustrator to increase the size of Panel of police find so I can see the full name of the police? Thank you

  Hi, is it possible in 2014 CC Illustrator to increase the size of Panel of police find so I can see the full name of the police?

  You can see on the screenshot below fonts with longer names are not displayed, I know you can see an excerpt from the police, but that slows down and me its not practical!

  Concerning

  

  Hi emiltsonev,

  We do not have an option to increase the size of this Panel. You can use the slider on the right to scroll.

  Thank you

  OM