Sudden problem with CFExchange

Similar Questions

• Sudden problems with Airplay, Apple TV etc with WAG320N

  Hi all

  Until recently I use DSL through my WAG320N and it worked perfectly. I used my AppleTV with airplay, Vuze, Xbox and so on without problem. I just moved to a new address with internet fiber. I've reconfigured the router for all route (and not an ADSL modem) by assigning the first to act as a WAN port ethernet port. Internet works fine as speed goes, but the wireless LAN is not optimal. I can't get my AppleTV to find iTunes on my laptop and Airplay is very slow and laggy. The router settings remained unchanged at first, but now I tried to reset to the factory settings and start over, this does not solve the problem however. I'm a bit puzled on this, as I know, the change of service provider (and go from ADSL to the fiber) should not have effects on the local network? I noticed that Vuze complains about problems NAT (just need to confirm that there is a NAT problem), but this should not matter in which of the local network, right?

  Any ideas what the problem might be?

  These devices are mentioned connected wireless? This could be a problem with wireless. It may be because of the interference. It is possible that in the new location, you have two or three neighbors who affects the Wi - Fi wireless signal. It is also possible that some other wireless devices are causing interference like cordless phones that moving on the same frequency with the router, the garage door openers and microwave machines. What you can do to prevent the interference must reconfigure wireless settings. Set width/bandwidth of 20 MHz channel and set the standard channel 1, 6 or 11. That should help him.

• Sudden problem with replacement of subset of table

  Hello

  I was working on my project when suddenly a strange problem appeared.

  I have a graph of intensity with 2 sliders that determine the coordinates of my area of interest. I created a simple solution to get these details and store them in table 1 d (x 0, y0, x 1, y1), hence I take them more later to perform some calculations. Now: it's all working fine and dandy that came out of nowhere share the table stopped storing the coords correctly. I put some sensors and index of the sliders and coordinates the eye to be acquired properly. But, for some reason, the function replace subset table stopped their storage in the appropriate cells. Whenever I move a cursor, its coordinates are now stored in the first two cells of a table. I'm pretty sure that I has not changed anything in the code, so what could be the cause?

  Screenshot attached.

  Oficmajster wrote:

  Yep, I added new cases of events previously: cursor type? It was empty, until he did change and why?

  If you don't the wiring of the table in the new case, the table in the shift register will be transformed into a table empty if running new cases. Once the array is empty, replacement of certain elements will not increase the size of the array, it will remain empty.

  Solution: wire the table across all new cases (if you create tunnels of entry-related, it will be automatically )

• Sudden problems with Adobe on Mac

  I have a Mac I-.  Used for years with Adobe to read and print PDF files.

  Yesterday, all of the sudden many questions.  Could not print some documents.  Other documents looked very strange, with black background and green type.

  Today, the message is that Adobe Reader cannot be opened.  As a result, cannot view or print PDF files.

  What is the problem?

  Hi jattogox96140952,

  Please provide the exact point of the software & OS installed on your system. Also check if it is there any update available for the software after crossing "" help > check updates "»

  Follow this thread to reset the Acrobat preferences:- How to reset preference settings in format Acrobat.

  Would like to know is what is happening with some or all of the documents.

  For printing issues, please refer to this article:- print troubleshoot PDF in Adobe Acrobat and Reader

  If the problem persists, then would you please check with the account of another user with Admin rights to reproduce the problem.

  Kind regards

  Christian

• Sudden problem with internet connection

  I run Windows 7 on VM Ware Fusion 6.0.6 on an iMac 2, 66 GHz Intel Core 2 duo with OSX 10.9.5.

  Until 2 days ago, everything worked well with my Windows apps and the Internet connection.

  When I now try to use Internet explorer, Safari or any other application using internet I get the message "computer not connected to a network.

  To aid in the troubleshooting of Windows I get the message "network cable is not plugged in correctly or may be broken.

  I reconnected the cable on both sides - computer and router - without result. But it is of course not the source of the problem since the side my computer Apple clearly shows that I have an Ethernet connection and I have no problem to surf, mail or by using any other application via Internet.

  Can someone tell me how to restore my Internet on the side of Windows 7?

  Thanks for your help

  Try to reset the router and the modem, if you have other devices that work always reset the router and the modem. Then if the problem persists, run Use Mail connection doctor - Apple Support by fashion that apple provides.

• sudden problem with HP Pavilion dv6-2157wm laptop

  Hello.  About 2 weeks ago, my laptop (a HP Pavilion dv6 model) worked very well.  It has been plugged in the power cord and adapter at the time.  One day, I went to check my emails and the laptop suddenly acted like it has been restarted, then it turns off completely.

  I waited a few minutes for re - turn on the laptop, but it does at all.  I unplugged the power cord and plugged in the power cord into the computer slot, but the led next to the power cord housing doesn't appear as it normally does when it is plugged.

  Also, when I pressed the power button to turn my phone back on, it lights.  Instead of this, a light in the front of the laptop (under the symbol of lightning bolt) flashes 3 times and then stopped flashing.  I took the battery and put it again after a few seconds, but it won't always turn.

  I noticed that the cord of the power box was nice and warm when the laptop shut down suddenly, as it was the laptop (despite the use of a laptop to refresh at the bottom of the laptop fan). The model number of the cord is WASGV0CL9YIVCU.

  What is happening with my laptop?  I use this unit to my secular Ministry work and need to work as soon as POSSIBLE!  I don't know if it's the power cord which broke or the battery needs to be replaced.  I bought the laptop in early 2010 and kept in good condition since then.  Help, please!

  Jessie

  Hey @prettykittyabc ,

  Welcome to the HP Forums!

  I understand you're Pavilion dv6 laptop does not light.

  The symptoms you have described would indicate the AC adapter or power cord no longer works. The laptop flashing lightning bolt symbol is the BIOS say you there is not enough power to turn on the laptop. If the adapter is connected, then it would be safe to say that the adapter is not power to the laptop, which would mean that the battery cannot be recharged.

  You can order online a replacement adapter, but I would say to contact the HP support by phone to order a replacement card for your laptop by phone in order to ensure the right adapter is purchased. Please contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click on the following link to get help from your region number: phone help around the world.

  Thank you!

• Sudden problem with XDCAM in first Pro CC (xd5c) files

  I have a project file, I was working on a couple of months ago using XDCAM (xd5c, HD422) of files, but since I formatted my windows machine because of hardware changes. Now I cannot import/link media in my project.

  I looked for independent codecs but they seem to be unsuccessful - even if I I remember at the time I started working on their having to search and I thought it was an AVID codec pack: http://Avid.force.com/PKB/articles/en_US/compatibility/en372311

  Someone knows how to fix this? Any help would be great!

  Premiere Pro doesn't have enough to work with the media, XDCAM directly from the device.  This is why I suspect this media don't come not in camera, or at least changed after from the camera.

• Problems with the radial tool and the gradient filter tool.

  I have suddenly problems with the radial tool and the tool filter degraded.  They are turning to my red while selection that the assets and not with the results of the any adjustments.  It is a new issue and out now where

  Does that help? Note that the tool must be active to see the check box.

  

  In addition, another reason, that you do not see it could be that the toolbar is not displayed. The toolbar display switch is to press the letter T.

• I am expierencing problems with my isight Camera on my MacBook Pro. Suddenly the video camera does not start (no green light on) FT or Photo Booth. The screen is black, if I restart computer it works but after closing the lid, it stops. V10.11.3

  I have problems with my view i camera on my Mac Book Pro. Suddenly the video camera does not work (no green light on) FT or Photo Booth. The screen is black, if I restart it, it works but after closing the lid it stops and I have to restart the computer.  I use V10.11.3. An idea about what is happening

  Hello mpm068,

  Thank you for using communities of Apple Support.

  Since your iSight webcam works up to the time that your Mac goes to sleep, I would like you to start please help desk trying to replicate this problem then to reboot in safe mode:

  1. Choose the Apple menu > shut down.

  2. After your Mac stops, wait 10 seconds, then press the power button.

  3. As soon as you hear the startup tone, hold down the SHIFT key.

     You must press the SHIFT key as soon as possible once you hear the startup tone, but not before.

  4. Release the SHIFT key when you see the gray Apple logo and progress indicator.

  To exit safe mode, restart your Mac, but no press during the startup.

  OS X El Capitan: start in safe mode

  Take care.

• Apple support has been unable to solve my problem with iTunes not responding do not. He started all of a sudden. A few weeks after I've upgraded to Windows 10. Reinstalles/uninstalled iTunes and nothing. Now, I can't even Apple support for help.

  All the sudden, iTunes has stopped responding. I click top and nothing. I spent over an hour with a Senior Engineer at Apple's Support, which does not give me a ticket number so now Apple can't even find the person I talked to. This person had to remember and it's been 2 weeks. I called Apple back Support and since they can't find a ticket number they told me that I have to wait until this person reminds me. This engineer had me remove and reinstall iTunes with all the other components that go with it, I run it as administrator, pretty much did all the troubleshooting I had done on my own. I have now to sit and wait, hoping that this senior engineer at Apple called me back. It's poor and poor support for iTunes. If anyone has any advice, please share.

  Thank you

  These can be things that you've already tried. Despite this, it might be interesting to try again. As another poster has said recently, though for another problem, "20th try was the charm.

  For general advice, see troubleshooting problems with iTunes for Windows updates.

  The steps described in the second case are a guide to remove everything related to iTunes and then rebuild what is often a good starting point, unless the symptoms indicate a more specific approach.

  Review the other boxes and other support documents list to the bottom of the page, in case one of them applies.

  More information area has direct links with the current and recent buildings if you have problems to download, must revert to an older version or want to try the version of iTunes for Windows (64-bit-for old video cards) as a workaround for problems with installation or operation, or compatibility with QuickTime software or a third party.

  Backups of your library and device should be affected by these measures but there are links to backup and recovery advice there.

  TT2

• having problems with the pop-up windows of analytical Google all of a sudden and now the pages are crashing or being redirected

  original title: google analytics popups

  Ive been having problems with the Google analytic pop-up windows all of a sudden now pages break or redirected, I've ran Malware, Windows Defender, a direct care, Avira, Avast and F-secure, and nothing seems to have read on other forums to help, that his may be a Trojan horse: Trojan.osx.Dnschanger.B... ive also rebooted my router as suggested in some forums , but nothing seems to help?

  Hi NicolaaTC,

  See the links below and check if it works.

  What is the browser hijacking?

  http://www.Microsoft.com/protect/terms/hijacking.aspx

   

  Difficulty of your web browser hijacked

  http://www.Microsoft.com/security/spyware/browserhijacking.aspx

• I have a problem with my indenting, there all of a sudden everything including the headers and about 2.5 inches in withdrawal. I have

  I have a problem with my indenting, there all of a sudden everything including the headers and about 2.5 inches in withdrawal.

  Looks like your BMP format is defined to respect the heads side.  Open the designer of TFP and try to put it like that...

  

  I have no idea why the script would have changed your BMP formats.  Depends entirely how the script was executed - the authore makes the script actually do.

  I suspect that you can import formats of a document where you have NOT run the script, and it would return to the formatting to the way you want.  I hope you save your work!

• Problems with windows update. all of a sudden the updates fail to install.

  I have XP media center edition 2002 sp3 version and I'm having problems with KB2621440, KB2647518 and KB2641653 updates all fail with the error 0x8007000d code. Last successful update was KB2660465 return 15 Feb.

  8007000D - Error_invalid_data.  Corruption in the folder C:\Windows\SoftwareDistribution.

  Rename the folder C:\Windows\SoftwareDistribution
  
  Click Start, choose run.
  In the run box, type services.msc.
  Click OK.
  Right-click the automatic updates service.
  Click on stop.
  Stopping the service will take a moment.

  Rename the folder "C:\Windows\SoftwareDistribution":
  a. Click Start, click Run, type %any and then click OK.
  b. right-click on the C:\Windows\SoftwareDistribution folder, and then click Rename.
  c. Type SoftwareDistribution.old, and then press ENTER to rename this folder.

  Click Start. Choose run.
  In the run box, type services.msc.
  Click OK.
  Right-click the automatic updates service.
  Click Start.
  Starting the service will take a moment.

  Restart and try windows update again. You will notice that your story will be available, but it's not important.

  If all goes well, you can delete the folder c:\Windows\SoftwareDistribution renamed after completion.

• My laptop has no sound? one day he turned suddenly silent and I can't find a problem with the drivers to fix

  No sound

  all the drivers r correct work n

  Hello Mohamed Ali,

  1. don't you make changes to the computer until the problem occurred?

  You can try the methods below to resolve this issue.

  Method 1:

  I suggest that you run the Audio troubleshooter on your Windows 7 computer, it looks for common problems with your volume settings, your sound card driver and your speakers or headset:

  Check out this link: http://windows.microsoft.com/en-US/windows7/Open-the-Playing-Audio-troubleshooter

  Method 2:

  Configure the playback devices from the default on your computer.

  a. Click Start, type Sound in the box to start the search.

  b. click sound in the results of search at the top of the start menu.

  c. click the Read tab.

  d. on the tab 'Read' it has listed the sound options at your disposal.

  e. Select the default playback device (the playback device will be the audio adapter on your computer)

  Thank you
  Irfan H, Engineer Support Microsoft Answers.

• BlackBerry sudden Z10 and serious problem with Z10 NEED HELP Please

  I have a z10, one of the first who came out in Toronto (if it is one)
  (difference), a few hours ago, I fell into a serious and sudden
  problem.

  I was able to swipe left and right between the pages of apps, even fall down
  Since the Summit, but I cannot open anything, not even not making a call or settings
  Options.

  Any time I try, for a fraction of a second, it looks like its about load
  something then nothing. (image slides to the right quickly and goes back
  each attempt)

  So I first did a reset, same problem, so I did a battery pull (15 minutes) and the problem is.

  I tried via USB to do a backup on blackberry Manager and maybe do a
  Re - install everything, but when I was invited to the password
  my camera on my PC, it told me that it was (I use a wrong password
  This blackberry on my computer 4-7 days a week, twice a day sometimes for an
  year and I have never miss typed my password, nor have I changed it)

  After trying everything to make sure that the first letter was maybe upper/lower
  cases, even my other possible phone password, nothing worked...

  On the 5th unsuccessful attempt my phone prompted me to type "blackberry", which
  I did, then I typed my password on my phone that I type in about 15 times
  one day because I put my phone in a lock in 5 minutes and has always said that he was wrong... I'm no attempt of 9/10 on and lost
  for options.

  Please if anyone can give me any suggestions, or even how do I back up my phone
  and now, or I have a previous backup of whipe form 4 months ago that I
  I wouldn't come back in the worst cases.

  Thanks in advance for your help

  Well... If you are in 9 out of 10 here and you don't mind not to restore your device, then enter the password again once and then the device should enter the device wipe mode. That will reset your device to factory setting and then you can start fresh by reloading your backup made the earlier