Switch QLogic 5200

Similar Questions

• 3Par QLogic zoning heterogeneous environment

  Hello

  I have a 3PAR F200 connected to two switches QLogic 5800 CF. I have 3 servers ESX (4.0 Update 1) with redundant of QLogic and a single Windows 2008 R2 Server with of redundant QLogic connected to the 5800's. I read the Guides implementation of 3PAR and was hoping someone who is familiar with this configuration could look both attachments and tell me if I've zoned it correctly, I think I have.

  I put the host type of character for the host esx generic 6-legacy.

  I put the host type of character for the Windows Server in 1 credits.

  I'm following vmware article 1008113 to strangle the queue depth.

  Thank you.

  Robert

  Look just to me - you do a zoning to initiator target/single, which is usually the right thing to do for insulation.

  -Matt

  VCP, vExpert, Unix Geek

• Satellite 5200-device display 801:Quick switch (Fn + F5)

  I have a problem regarding the fast display device switching "pressing the (Fn) with (F5)" nothing happen as usual... does everything body knows how to fix it!

  Thanks in advance.

  my laptop is 5200-801 with Nvidia 460Go with 46 MB.

  Hello

  If you change with FN + F5, you need the Hotkey Utility from Toshiba! This can is located on your CD of tools or Toshiba download site!

  Good bye

• Satellite 5200 - powers automatically (sensor/hall-magnet)

  I have an automatic feeding weird issue with my laptop Satellite 5200.

  * Situation. *
  1 laptop is turned off and the cover is open
  2. I close the lid while the laptop is always off (just battery is connected)
  3 result: the laptop automatically and boots: how weird is it that

  It has something to do with the magnet that is integrated in the screen/lid place/located near the right hinge. When you close the magnet is close sensor (hall sensor) and apparently, this magnetic field causes the cell to initialize. Normally, if your laptop is running and you close the lid of your laptop computer goes into mode sleep with this technology (magnet and sensor). My laptop works well if she runs and I close the lid. Then it goes on standby as expected. When I opened the lid he returned from sleep mode.

  The issue I am facing now is really just when I close the lid, * while the laptop is turned off already *.
  How do I fix this behavior stupid - how to adjust the magnet/sensor so it has not received the impulse to automatically feed upward.
  The solution must be around here somewhere. And I don't think it's a software configuration problem, because the laptop is turned off when this occurs - so no Windows is running, it is not in standby or hibernation mode.

  Your help would be appreciated.

  Thank you very much for your advice!

  Hello

  If he s really a lid switch problem then it would mean that there is a mechanical problem that could be solved by a service partner
  But I think that this is not a sensor problem possibly display frame/cover touch the power button (that's my opinion) and that feeds on the new laptop

  Just a question; What is cable LAN connected to the laptop when the laptop automatically?
  If Yes, then I would recommend checking the BIOS if the Wake up on LAN option could be disabled
  In many cases, it would lead to the reactivation of the laptop

• Tecra 5200 - nothing happens after pressing the power button

  When I press the 'power' of my Tecra 5200 kids button nothing happens, only the front panel power led lights, but laptop does not start - in fact, nothing happens.

  Earlier, I lived as a result of problems;
  -the internal HARD drive didn't work, so I put the HARD drive in the Select Bay adapter and switched 2 hard drives (for each child 1 HDD with their own software / games)
  -computer had very hot on the surface (I had tried to open the computer and to clean inside, but it is still very warm)

  Now to my question.
  -If the computer does not start, is because of the HARD internal disk problem (found out once in awhile, he recognizes an old HDD, I had attached to internal port, otherwise the DVD player was not working)- and an easy repair is possible
  - or would it be possible that the CPU got too hot and bust, which means that I spend any money on the repair.

  I hope someone can help and give his opinion.

  > Toshiba guy;
  > Please publish guides on your website on how to open the 'old' notebooks, in fact no one would spend money to repair them.
  I agree with you. I don't think that someone will spend a lot of money to pay reparations for these old books.

• How to install wireless on a Satellite 5200 903?

  Due to a very bad virus, I got Windows on a Satellite 5200 903 a friendly businessman. But at home he saw: no wireless LAN could be used... It seems, that cause the WLAN switch is 'off' no WLAN-driver was installed/recovered...

  Now, he wants to come to me tomorrow or day after tomorrow - and I need TO know how to install everything until there... He'll also bring me his router, so I can configure everything for him on the LAPTOP AND router (WPA, if possible).

  But I found TWO drivers: one was a direct download of a small 'Agere' file - wlesslan-xp - 7620390.zip

  The other comes from "Atheros", and the download are a links to another website "Toshiba EMEA - Wireless LAN Driver Portal" http://aps2.toshiba-tro.de/wlan/?page=downloads, where I have to identify the WLAN adapter... But: on the first download site (I mean before you redirect to 'Toshiba EMEA') it is on the list of "Models" NOT any Satellite 5200.

  The pilot who is correct? Are there different WLAN adapters in the 5200-903 series? Is it possible to find the adapter model BEFORE it gives me the laptop?

  In the list of the drvers for the 5200-903, there's a "hotkey WLAN" Download wlkey-xp - 2003.zip? Who should I too? Do I need other things?

  And such a 'old' WLAN-access works in a different way the WLAN integrated a centrino for example? I don't know how to connect to a WLAN with new laptops: "wireless networks" button on the right button fot windows, then choose the name WLAN to connect and enter the key, if necessary.

  Please help me, he lives 100 miles away from me and has not much time, it is once again for me just for this issue and, of course, he was not amused when he went home and cannot connect to internet... and it is a noob ABSOLUTE in technical things so I can how make him on his own and needs your help quickly.

  Thank you very much!

  Hello herbal

  I want just to make the story short and simple. After installing the OS install drivers for the hardware components. According to the specification of your laptop for Satellite 5200 903 what WLAN ready model and I don't know what WLAN card is inside. Your friend must have information about this.

  If there is card Atheros WLAN driver you can find HERE

  After installation of the driver install all Toshiba designed tools and utilities from COMMON MODULES. It must be installed first. WLAN-hotkey utility is important because using the FN + F8 key combination you can enable/disable wireless network card.

  Software WLAN (WLAN Atheros client utility) is not necessary, because to the WLAN, you can use WLAN WXP parameters. You can use it if the wireless network adapter is enabled correctly.

  So I hope you set WLAN correctly and if you need further assistance please write back.

  Bye and good luck!

• Broadcom/qlogic npar distributed and strategy MPIO on Windows 2012R2

  Hello

  I enabled Distributed on partition 0 in our FC630, card broadcom/qlogic 10GbE. After all configured on MS iscsi initator then I saw all the paths were active for some time (10-20 min), then one of the paths is all just disappeared and never reconnected.

  I see the message "disconnection request has been received from the initiator" on the EQL newspaper but is not very useful. Curiously, it was precisely the LUN; I saw no problem for vss-control. So I was check the option and I noticed that if I change the "least queue depth" MPIO "failover only" then I see no loss path.

  As I'm not sure why the default "least queue depth" option does not work, I would be grateful for any insight and details.

  Thank you

  Hello

  If you open a support case, they probably have you say that it works as expected.  Since EQL FW 6.x our MPIO code negotiates connections as needed.  To ensure effective performance and minimize the number of connections.

  The event message you included confirms that.  The "requested disconnect" comes the HIT MPIO code.  The 6210 has vertical tipping so with little traffic that one connection is necessary. A failure of the cable or switch will not lower your volume.   If the load rises another connection will be established.

  The settings in the registry that Michael mentioned substitute is no longer trading code in the firmware and the HIT.

  Is there a feature request for the connection of two minimum for better offer peace of mind to our customers during this behavior.

  Since you are dealing with a single member, the greater benefit of our code MPIO is not be used.   This requires several members in a pool.   With a single member, you won't see any difference w/LQD on Round Robin.

  Kind regards

  Don

• Configure MXL switches blade for active paths using 2 Qty ANC

  Dear members,

  I need to configure a solution in which 2 CNAs Qlogic 57810 s was used to LOM & port B of each server blade m630, converged switches in A1A2 B1B2 & cracks MXL. All switches have under the IO modules mentioned:

  • Ports SFP + 10 GbE Module 4 port replaceable hot 4 x SFP + (optical or direct attach cables)
  • Fiber Channel Flex Module e/s, with 4xDell, networking, transceiver, SFP +, CF, 150M, SW, FIN

  Here are the requirements of the customer

  • Battery A1A2
  • Battery B1B2
  • All roads for SAN i/o Flex modules & LAN of SFP + must be active asset for a redundancy level CNA. attached is a diagram for a better understanding.
  • All empty ports of each switch blade ends at the DMZ switch with SFP + converter RJ45 1GBE customer.

  I know how to stack together A1A2 & B1B2 spend together, I need to know what needs to be set at the level of the CNA to support active active connections/paths. In addition, A1A2 & B1B2 switches to support IO END & Flex for convergence n/w infra.

  Your plan sounds great if there is any VLAN.

• Cisco Nexus switches

  I'm looking to deploy a series 5100 Cisco NEXUS switch at 10 Gbps.

  I know that the Nexus is supposed to work with the converged network adapter (for 10 Gbps FCoE, etc.), but can it operate without an ANC?

  I want to put some passthrough 10 Gbps modules in my Dell m1000 chassis and the cables directly to the Nexus switch.

  I know that the Nexus is perhaps overstated for this solution, but it is a step in the UCS solution for us.

  Thoughts?

  James

  Hi, you don't need special drivers for "low latency" 10 Gbit ethernet on a 5 k.

  for example, to switch non-nexus 5 k

  PING 10.10.10.1 (10.10.10.1) 56 (84) bytes of data.

  64 bytes of 10.10.10.1: icmp_seq = 1 ttl = 255 time = 0,530 ms

  64 bytes of 10.10.10.1: icmp_seq = 2 ttl = 255 time = 0.618 ms

  and a nexus 5000 with a qlogic 8152

  PING 172.16.78.3 (172.16.78.3) 56 (84) bytes of data.

  64 bytes from 172.16.78.3: icmp_seq = 1 ttl = 128 time = 0.150 ms

  64 bytes from 172.16.78.3: icmp_seq = 2 ttl = 128 time = 0,134 ms

  Oracle rac cluster will fly!

• Buzz of noise in the tempo switch

  My song has 4 different tempos. Every time that happens, occurs a humming noise. If I get all tracks FX behind it disappears. How can I keep the delay, but not the buzz?

  Thank you y´all.

  Use automation for on/off switch of the delays to and after each change of tempo.

  If that kills too late in the face of that time, and then introduce a Gain ahead of every delay, automate the Gain to cut admission to the delay when changing the tempo. Who will cut the whole track, however.

• Switch between keyboard languages 3 (or more)

  I have three languages: language A, language B, C language

  I'm on A language and to switch to the C language.

  Heat the shortcut keyboard CMD + space twice to change the language. It's change of a language.

  I have heat twice again and it works properly.

  How to disable this smart switching algorithm?

  You really tell us that what you see in the menu 'flag' on the top right of the screen does not always match what is typing at the keyboard?

• Can I switch to OSX 10.9.5 directly to Sierra.

  Can I switch to Sierra de OSX 10.9.5 no other updates between the two?  I have an iMac mid-2011.

  Yes.

  (145115)

• on/off switch does not work since the SIERRA

  Hello

  Since I'm sierra os that the on/off switch does not show me the dialogue window in which you can choose between power, reset, disconnect you.

  This is a problem of Sierra? There is an option in the system Pref?

  Thank you

  It works very well in the Sierra.  Simply press the button longer.

• Airplay iMac switches back on computer after you select the apple tv. Why?

  From Imac display by selecting Appletv heard music lasts for a few minutes then switches to my computer. Why?

  Hello brianfromsooke,

  If you try to use your iMac, Apple TV AirPlay, but the audio output automatically switches to your iMac, it may not be the flow enough on your Wi - Fi network.
  

  If AirPlay disconnects itself, your wireless network can be too busy or have too many wireless interference to maintain the connection of the antenna. Learn how to solve the problems of Wi-Fi connectivity. The manual of your router network may have additional suggestions for maintaining a strong and fast connection with your devices.

  Use AirPlay to view a video of your Mac on a HDTV

  Sincerely.

• I am on a MacBook Pro mid 2012, Yeosmite 10.10.5, I want to switch to Sierra and am nervous to do when I had a terrible experience upgrade to Yosemite.  I have everything backed up on Time Machine. Can you please advise me?

  I am on a MacBook Pro mid 2012, Yeosmite 10.10.5, I want to switch to Sierra and am nervous to do when I had a terrible experience upgrade to Yosemite, support with gratitude by Apple in charge.  I have everything backed up on Time Machine. Are there steps of preparation I need to do before you download and upgrade to Sierra.  Can you please advise me please?

  N ° so you have a backup if something goes wrong you can return to Yosemite.

  Only concern is that some devices, including USB that may require the updated drivers, but these records are not always available

  This is the Office Mac Pro forum. I asked that your post moved to the forum of laptop MacBook Pro or another appropriate forum.