Tap 10 on a profile or a Codec C40

Similar Questions

• matching codec c40 with ISDN link problem

  Hello world

  Would really appreciate if someone can help me with my problem.

  I have 2 sites. Each site has a c40 codec which is connected to a cisco ISDN link box. Each box contains 3 BRI connections. The system is essentially set up at the video-conference from one site to the other. C40 codecs have been paired with boxes of ISDN link manually due to the old firmware. Now that the firmware has been upgraded on all devices, I am trying to pair the codec with the ISDN link using the 'auto' mode so I can configure the ISDN codec c40 GUI link.

  The problem I have is that when I pair it in auto mode, the ISDN link is seen by the codec and matched succesffuly but I get an "error" and the reason for the error is "no sip registered to peripheral H320" or something of the sort. The rest of the configuration is the same, all im doing is pairing in auto mode. At this point, I can't do a video call-out. Can I make changes to the GUI hoewever c40 ISDN link and it shows as paired.

  When I change the sip profile out to 'off' in the sip codec c40 profile settings, now, there is no error. The sip profile in the ISDN link area is also set to off.

  Can someone help me what are the correct settings for outgoing SIP and the above error message please. It will be greatly appreciated.

  Thank you

  Hello

  Outgoing SIP should be turned off if you use the ISDN codec liaison, so please meke it took off.

  for the composition, should not use composition commnad complex that you scoop with TC 5.x and IT 1.0,

  With TC 6.x just enter number and select protocol H320.

  HTH

  Kind regards

  Dharmmesh

• Backup of configuration Cisco Codec C40

  Dear all,

  Can I know how to take backup of the configuration of the Cisco Codec C40, please?

  And also help me with the document of the administrator?

  Thanks in advance

  Kind regards

  Syed

  You can simply copy the output of the xConfiguration and paste it into the SSH client.  You may need to change the output a bit to get the correct formatting, however.  For example, the output registered since my SHH client contains a preceding * c which must be removed before that I can stick again in the SSH client:

  *c xConfiguration Video Wallpaper: Waves

  When you perform a software update, codec configuration, including the keys installed option is not affected and will remain in the process. Keys options include Premium (PR), double (DD) display resolution and Multisite (MS). C40 has been end of sales since June 2015, so it is not possible to order anything for this, see eos-eol-notice-c51-733467. Procedure to upgrade the software codec is on pg 28, the same page mentioned in my previous answer. To upgrade codec software, you will need a release key when switching from one major version to another, as TC5 to TC7. You can request a release of the Cisco Licensing Portal key > obtain other Licenses > telepresence free software key, as long as the device has an active support contract. If you do not have an active support contract, you can contact TAC and get the free unlock key by referencing the Security Advisory cisco-sa-20160504-tpxml, which you can get a key to unlocking TC7.

• duplicate calls made using the alias between two codecs C40

  We have 2 new codecs C40.  When calling between the two using the alias, it seems that 2 calls are made.  In a sense, we get a very quick disonnect message upon acceptance of the call.  In the other direction, the call comes in, but on disconnect, we get a message saying missed call.

  Seems that the search rules can be duplication of the call some how - probably him endpoint becomes a call SIP and H.323 call at the same time. Could you post the call details and history/details of research?

  Sent by Cisco Support technique iPhone App

• Need help with the command options of codec C40

  Hello! I plan to buy a few codecs C40 and seller offers me to buy three options for this, but I can't find a description of these options. Seller is not so appropriate as I would like and these options cost a lot. They are here:

  LIC-INTP-C40-DD	Option of dual inclusive package C40
  LIC-INTP-C40-SM	IntPkg Codec C40, 4Way individual transcoding Multisite
  LIC-INTP-C40-PR	IntPkg Codec C40Premium resolution (1080 p/720 p 60) Option

  I found the document with similar options here (table 3), but there is also no description:

  http://www.Cisco.com/en/us/prod/collateral/ps7060/ps11304/ps11312/ps11332/data_sheet_c78-628593_ps11422_Products_Data_Sheet.html

  I think that these options it is me

  one) to use two screens (only two or more?) with C40

  (b) serve as C40 MCU for up to four sites without going through any additional autonomous MCU

  (c) to use video FullHD for videocalls (but I'll buy cameras 1080 p for C40, I need licence also for C40?)

  So, I would ask someone who is familiar with the command of Cisco/Tandberg to describe these options.

  You are actually right on your assumptions and descriptions, you just pretty much what each of these options do listed.

  Dual display-

  C40 has the ability to display the same video on both outputs by default, if you do not get this option.  This option is to display two separate video sources on two screens, such as: Farsite on output 1 and content/selfview on output 2.

  High resolution-

  You might be buying cameras 1080 p but resolution premium will allow you to pass resolutions higher during a call.  You can still view the full HD video when not in a call although if you choose not to get this option.

• 1 2 codec C40 camera

  Hello

  One of our clients have existing C40 telepresence video system and they want to add another codec C40 and connect it to the camera of the current system of C40. One camera, shared in two units of codec C40. Same room/location where to install the additional codec.

  The goal, why the customer want this configuration because the existing system of the C40 was used by one of their partners and dedicated for that specific partner. They want to invest another C40 codec for their own video-conference sessions and for budgetary reason, that they just want to buy a codec and the use of the device the other C40 system's existing.

  Even audio and video resources will be used. Audio and video distribution amplifiers are not a problem on this configuration.

  My concern is that is - it possible to use a separator of type RJ45 for control of the camera's two codecs C40. The codecs will not be powered on at the same time.

  And what could happen and if two codecs are accidentally turned on simultaneously. ?? Can it damage the camera?

  Looking forward to your recommendations and your ideas.

  Thank you!

  Acevirgil

  Hi Acevirgil,

  This is something not an ideal package to the top and I do not thing anyone he tried again. and he's going to run on no it is not planned.

  Now you are going to use spillter on RJ45 and HDMI port,

  Remember, you make a divider appropriate according to the pinout of the control cable. If the cable is long enough according to the prescribed length you will need to turn on the external camera. and you question if the two codec lights suddenly the camera answer is NO (to me), that power is not very high.

  You can then go ahead and try first by a Dispatcher and test it before purchasing.

  It can work if the wiring is done correctly.

  Thank you

  Ravi kr.

• Cisco Codec C40

  I've recently updated the software on a device of cisco codec c40.

  The software has also updated the firmware on camera1.

  Unfortunately it didn't update the firmware on camera2.

  The cameras are connected in Garland.

  Is there a simple way to update the firmware on camera2? (Such as running certain commands on c40 codec?)

  Camera 1

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB50D00386 [ID:40083] 2012-12-10

  Camera 2

  Cisco PrecisionHDMC 1080 p 12 X S01718 - 4.0FINAL A1AB47D00079 [ID:40076] 2012-05-16

  See the following document, it is old, but still relevant.

  https://supportforums.Cisco.com/docs/doc-24351

• How can I enter a range of IP access codec C40 using RemoteAccess allow?

  Hello

  I'm setting up a codec C40 running Software 6.1.

  I want to limit systems that can access the codec through SSH/HTTP etc. and found authorize RemoteAccess under Configuration > System Configuration > network

  I want to enter a range of addresses (192.168.2.1 to 192.168.2.254) but may not work on the syntax to do this. The Administrator's guide and QAnywhere mention that ranges are supported but only provide examples for specific hosts.

  Can anyone help?

  Hello

  I think that the command affects the iptables on the codec which is a linux-based system.

  For the 192.168.2.1 to 192.168.2.254 range you might have to specify the following:

  xConfiguration network 1 RemoteAccess allow: "192.168.2.0/24.

  I tried this on my system:

  xConfiguration network 1 RemoteAccess allow: "144.254.10.0/24."

  Then the iptables show entry suite:

  [dderidde-ex90-home: / var/log/eventlog] $ iptables - n list

  INPUT string (policy ACCEPT)

  target prot opt source destination

  Admin channel (1 items)

  target prot opt source destination

  ACCEPT all les--144.254.10.0/24 0.0.0.0/0

  Drop tous--0.0.0.0/0 0.0.0.0/0

  That should do it I think.

  Danny.

• Cisco profile series - vs vs C40 C20 C60 codec

  Hi people,

  Is there an online guide that can give me some information about comparisons between codecs c20, c40 and c60 on video profile 42 series systems and why it has such a big difference in the price that is, what have you found to this extra cost?

  Also, is it possible to connect an external projector codec to view the video of the codec on the overhead?

  Thank you

  Hello.

  Yes, it will be possible. You have several inputs and outputs on different codecs.

  The main difference between the C series are physiqueet inputs and outputs and call functions.  See the tables below.

  Models top means more inputs and outputs.

  There are more features than this, but the list shows key capabilities

  	C20	C40	C60	C90
  Resolution	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
  End to end	720p30 +.	1080 p 30/720 p 60	1080 p 30/720 p 60	1080 p 30/720 p 60
  End to end double-flow	p15 1280/768	1280 × 768 p 30	1600 x 1200 30 / 1080 p 30	1600 x 1200 30 / 1080 p 30
  Output and input physical
  Mic input	2 mini jacks	2 XLR	4 XLR	8 XLR
  Video in	1 + 1 DVI HDMI	2 + 1 DVI HDMI	2 + 2 DVI HDMI	4 HDMI + DVI 2
  		1 S - video / Comp	1 S - video / Comp	HD - SDI 4 component 2
  				1 comp / S-Video
  Video output	2 HDMI	1 + 1 DVI HDMI	1 HDMI + 1 DVI + Comp	2HDMI + 2 DVI + Comp
  MultiSite	NO.	4 way	4 way	4 way
  Resolution

  576 p 30 720 p 30 1080 p 30/720 p 60 Other API API API GPIO GPIO Processing power

  Thank you

  Marius

• How to dial directly to an IP address (point to point a.k.?) of the Codec C40

  We are looking to replace old Polycomm and Tandberg units with a telepresence C40 faithful.  On old Polycomm and Tandberg units, we can simply enter the endpoint IP address and connect.

  This unit of C40 has been attached to a CUCM and worked through their guardian.  We have done a factory reset the device, so we can move our network IP "Naked" in an accessible IP address.  However, we cannot make calls: it simply says 'Connection' and is there, doing nothing.

  Troubleshooting-> Diagnostics Web page, said "the call by default protocol is set to Auto, but the system is not registered on this Protocol".

  I guess the C40 can direct an IP address as our previous Polycomm and Tandberg units?

  Should what settings I use as the DefaultCall Configuration?  For the moment, it is 'auto '.

  In Configuration H323 I;

  NAT
  Set to Off.

  Profile 1
  CallSetup in direct mode
  PortAllocation the dynamic value

  Authentication
  LoginName is empty
  Set to Off
  Password is empty

  On the System Configuration in SystemUnit page I ContactInfo Type set to Auto.

  I don't know what I should put in E323Alias.  I guess it can be left blank?

  Help set up for direct IP point to point my calls really appreciated.

  Hi juddernaut,

  These forums seem a little foires right now and you have posted double https://supportforums.cisco.com/discussion/12137686/how-dial-direct-ip-a... (made it myself, because they take an age to the answer). I would like to delete the other post.

  Set the configuration of appeal to force H.323.

  The E.164 alias is a number as an extension system, but unless you have a doorman with dial plan of this won't be necessary and can be left blank. However, its value put something in the name of the system box so that the other side can see appealed.

  You should be able to dial via direct IP - I suspect his tent to dial via SIP and failing. Forcing them to use H.323 should do the trick.

  Chris

• Cisco Codec C40 remove wallpaper

  Hi all.

  In our installation of cisco telepresence, that we met an interesting question:

  the cisco c40 codec admin created a custom wallpaper, somehow this wallpaper was not appropriate for this codec for 100%.

  After that he transferred the wallpaper on the unit - it restarts. We see a cyclical reboot - boots of unity, we see a cisco logo, then we see a (part of the GUI) overlay on the monitor, after this codec is trying to load wallpaper, fails and went into reboot.

  Are there ways to manually remove this wallpaper of the codec s flash without hard resetting the codec?

  Hi Eugene,

  Try to login as an administrator using ssh/console and run the following command:

  xConfiguration video wallpaper: Summersky

  Best regards

  Sergey Kuzmin

• Cisco TelePresence system Codec C40

  I activated high security and after the reset mode, I can not connect with any account via the web site. Any suggestions?

  Keep informing me that the credentials are not valid...

  If there is no prompt to change your password to meet the security requirements (see the C40 Administrator's Guide pg 48), or you are not able to use or the old password (before being forced to change).  The only thing I can think is if you have no login required turn on to the serial port, you can directly connect the codec and change the admin password.  Essentially, you have forgotten the password and the only option is to reset factory endpoint, if it comes to it, see this discussion: password recovery.

• Updated codec C40 to the latest version of the TC software - use CUCM?

  I need to upgrade our C40 codecs to patch the vulnerability of Bash.  Currently they all run TC5.1.3.292001.

  I noticed a few options in the download options for the included C40.

  (1) Non-crypto and crypto software.  The way I read it, this refers only to the software itself, not any kind of codec options?

  (2) "to be used with CUCM"-I'm not sure how to check it. "  I inherited these devices with no documentation and the original seller is pretty useless.  Is it possible to check?  We use CUCM, but to my knowledge, our phones can't integrate directly with the TP system (we have customers MOVI for this).

  Stuart,

  I don't think that Cisco has published a version of TC software that has the fix vulnerabilities of bash.

  The non-crypto software has none of the feature SSL on it - IE. signaling/media figures. Usually goes with cryptography is the safer bet unless you're from a country that has to import restrictions.

  CUCM - if your termination points are saved to CUCM, then you must use the version of the file CUCM. It will be uploaded to the server CUCM himself by going to install/upgrade the Administration of Cisco's operating system and restart the TFTP service. In this way, the file will be pushed down from the server when the codec is reset.

  For the non-CUCM, you use the other file and download the .pkg directly on the codecs. It seems to me that you have a VCS based so the .pkg file deployment, this is what you will use.

• Codec C40 - remote control / Touch Controller [a]

  Hi all Experts TP,

  I just bought a C40 and put in place. I have the "remote control" and "tactile controller", that are put in place normally and can

  particularly well-run.

  But who cannot work together, this means I plugged the 'remote control', then the controller 'touch' cannot be used and I plugged the controller 'Touch', then the 'remote control' cannot be used.

  I can only use one or the other controls?

  Hi Fai CHi,

  Yes, you can use a single device at a time.

  Best regards, Ahmad

• Strange codec / import issues after update 20141

  Well, I'm bit clueless about a rather odd behavior since the update to 20141.

  Somehow first has problems with multiple codecs that work fine with 2014.0.0 and 0.1

  for example: AAC-Audio in many forms.

  
  

  Audio

  ID                                       : 2

  Format                                   : AAC

  Format/Info: Advanced Audio Codec

  Format profile: LC

  Codec ID                                 : 40

  Duration: 19 minutes 29 seconds

  Duration of the source: 19 min. 29 sec.

  Bit rate mode: Variable

  Flow rate: 192 Kbps

  Maximum bitrate: 251 Kbps

  Channels: 2 channels

  Position of the channels: Front: L R

  Sampling: 48.0 KHz

  Compression mode: lossy

  Stream size: 26.4 million (0%)

  The video stream corresponding (h264) works very well. The same file works without any problem in 2014.0.1

  Even made an another file mp4/h264 + aac right out of first 20141 results in the same issue that I can't import the file back to the first without losing the audio stream.

  The next strange thing is a file just with an Mpeg2 Video stream:

  General

  Full name: D:\Output.m2v

  Format: MPEG Video

  Format version: Version 2

  File size: 362 MiB

  Duration: 10 min 0 sec

  Overall bit rate mode: Variable

  Overall bitrate: 5 058 Kbps

  Video

  Format: MPEG Video

  Format version: Version 2

  Format profile: Main@Main

  The format, BVOP settings: Yes

  Format settings, matrix: Default

  Parameters of the format, GOP: M = 3, N = 12

  Duration: 10 min 0 sec

  Bit rate mode: Variable

  Flow: 5 058 Kbps

  Maximum bitrate: 7 000 Kbps

  Width: 720 pixels

  Height: 576 pixels

  View picture format: 16:9

  Frame rate: 25.000 fps

  Standard: PAL

  Color space: YUV

  The chroma subsampling: 4:2:0

  Color depth: 8 bit

  Scan type: Progressive

  Compression mode: lossy

  /(pixel*Frame) bits: 0.488

  The first frame of time code: 00:00:00:00

  Stream size: 362 m (100%)

  The file has been exported with first 2014.0.1 and I'm able to import it ti 2014.0.1 without any problem. But 2014,1 indicates that the file contains no supported formats.

  All this is repeatable that I re - install 2014.0 and everything works - and 20141 with these problems. This problem appears in new projects as well as in the 2014.0 - imported projects.

  I found another statement of this kind of problem here: https://forums.adobe.com/thread/1595720 - but the proposed solution does not work for me.

  So - any suggestions?

  PS: 2 screenshots (same file in 2014.0.1 and 20141) and link to the .mp4 file used:

  

  

  File: https://www.wetransfer.com/downloads/6a22bbc6e0bf4e6eb4ee52c4f710922220141013131512/699af4 628ca4c2579b20903f4a4918d820141013131512/833bd0

  Hello

  You can try and reset the preferences. Go to adobe documents. Rename the old adobe adobe folder.

  By doing this, you will lose the custom keyboard shortcuts.

  Check whether or not this step allows.

  Thank you

  Arjun