Tecra A10 - no sound using Win XP

Similar Questions

• Tecra A8 - no sound using Win XP

  I installed windows xp on my Tecra a8.
  Windows detected the realtek hd audio card. I installed the audio driver, windows can play music, but there is no sound.
  The "speaker" icon is not cut.

  I'm going to Panel speaker - its - control - advance - and selected portable stereo speaker and headphone but still no sound.
  I pressed ESC (a speaker symbol), the volume button in the middle of the base but still no sound.

  Is this hardware problem?

  Can someone please

  Hello

  Win XP SP3 is needed because SP3 contains significant fixes for HD audio driver.
  It must install SP3 first, then the audio driver!
  If driver sound has been already installed, then remove it and then install SP3.

  Also, I found this FAQ from Toshiba:
  http://APS2.toshiba-tro.de/KB0/TSB7C021B0001R01.htm

  It s related to the Vista operating system but maybe you should try it under Win XP!

• Tecra M2 - no sound using Win XP

  Hello. IM in the States by the way. I couldn't get logged in the other forums of Toshiba. (Don't ask). So ill just ask for help here.

  I have an Audio/speakers/Sound card problem. I don't know who it is, if any. I have a Toshiba Tecra M2,
  Don't know what model. Under my laptop, it just says: Tecra M2. Made in China. I got it off the coast of a friend, don't know where he got it.

  After I got it, I installed Windows XP Home sp3. Updated some hardware that could not find drivers and everything works fine
  with the exception of my sound. I have a good driver, no warning of any yellow exclamation point. I checked and double-checked
  and triple checked all volume and mute options. The volume knob on the front of the laptop is turned upward.

  I installed these patches UAA

  After checking KB888111WXPSP2 on 21/01/2010
  After checking KB888111WXPSP3 on 02/02/2010
  passed verification KB898461 on 20/01/2010

  Go to administrative tools > Services > Windows Audio is started and automatic.

  I installed the Chipset first and re-installed my audio driver utility. Still not fixed.

  I get sound through the headset. But is all torn, looks like someone took a screwdriver
  and dug around in it. The helmet is not same snap tight as it should be, he wiggles around.

  So I have to move the CAP autour until I find the right place and the Øresund will play through the headphones, but the slightest bump
  to it will cut off the sound of the headset. I tried to move card into the socket to take off all the sensors stuck in there,
  (if it is left there.) That did not work.

  So I thought that I work around the internal speakers and headphones and just buy a few external USB Portable speakers.
  so I did, and they do not play all the sounds! I am in a bind. The only thing I can think is if I update my
  The motherboard BIOS and perhaps the noise will kick in. I checked my current BIOS settings, there is nothing on the Audio or sound. But I don't know what BIOS file for in downloads. If someone could help me here I would much apreciate that too.

  If anyone has more ideas on how to solve this problem, please, please offer advice you can think. Thank you.

  Here is some info on my PC laptop Toshiba Tecra M2.

  Operating system
  -----------------
  Windows XP Home Edition Service Pack 3 (build 2600)
  Multimedia
  -----------
  SoundMAX Integrated Digital Audio
  Driver date: 01/09/2004
  Driver version: 5.12.1.5240

  If you need more info, just tell me what to do.

  Inside the headphone jack there is a small mixer. This switch disables the laptop speakers when the headset is connected. Perhaps this little switch is broken or somehow can not activate Laptop speakers when the headset is disconnected. So you can have good working sound card, but you do not hear anything on the laptop speakers.

• Tecra A10 - 12z - cannot install Win XP - No HDD

  Dear;

  I bought a new laptop Tecra A10 - 12z, having a Vista operating system.
  I fixed my laptop and now I want to install a Windows XP operating system

  When I install Windows xp, Setup Wizard download windows files, but it cannot start.
  Troubleshooting comes up saying there is a mistake and try to scan drive hard with / f for fixing.
  What can I do?
  I am in need for the version of Windows XP.
  My xp backup CDs are broken and I'm not in my country of today.

  Note: I tried to format the hard drive and also tried to install winxp on win vista, same problem same error.

  Thanks for help.

  Hello

  You was not able to install the Windows operating system because you have not installed the SATA drivers that are needed to recognize the new SATA HDD controller.
  The SATA drivers are part of the Intel Matrix Storage Manager.

  You can build an own Windows disc using nLite software and might include drivers SATA on this CD.

  I recommend research and read the forum discussions related this topic.
  There is a lot of discussion on the same topic!

  Welcome them
  Jeffrey

• Tecra A10-112 - cannot use 8 GB of RAM

  Hello

  I'm trying to upgrade the memory on my TECRA A10 - 112 PTSB1E (Windows 7 and Server 2008), when I upgrade to 6 GB ram (1 x 4 GB + 1 x 2 GB), there is no problem what so ever (52 MB hardware reserved + 5700 MB useful) Windows.

  But when I go to 8 GB of RAM (2 x 4 GB) I get material dedicated to the memory of 4297MB and 3129MB of memory used (under windows) and I can not find how to reduce it to 6 GB levels. The bios sees 8GB, windows detects the 8 GB and the fact CPUID. I tried to update my BIOS on Toshiba support site, but I get "Computer not supported" message when I run the update file, I downloaded at Toshiba.
  Any help would be appreciated.

  Thank you

  Andy

  Hello

  It would be interesting to know which modules of memory you use exactly. You use the noname or high quality, e. g. Kingston modules?

  Maybe the modules are not fully compatible, so you should test the other modules.

  Also, what program/tool tells you this information on reserved hardware memory? If the BIOS and Windows recognize 8 GB, everything should be ok.

• Satellite U400 - 10l: no sound using Win XP 64-bit

  So I do not where to start...

  I have some problems with note Satellite U400 - 10l.
  Today I ' m trying to install winxp64b to my note. but after the installation starts more problems...

  the its don' t work? But why I ' m donwlod good pilot...
  Since the installation of sceer print driver...
  [http://tinypic.com/r/28wglcx/6]

  then the following... in system maganer for windows problem
  [http://tinypic.com/r/2woj1qv/6]

  could you please... give me the link directly to the correct drivers downoad?
  hepl me please! someone...

  Hello

  Satellite U400 - 10l belongs to the series of PSU40E and it supports the audio chip Conexant CX20561
  You need the Conexant audio driver in order to get the proper functioning!

  Please note that the Win XP drivers placed on the Toshiba page are released for Win 32 bit OS! Usually, they don t work with 64 bit XP!
  If you need Win XP 64 bit Conexant sound driver you need to search n 3 third-party pages for this driver.

  In addition, you must install Win XP service packs newer!
  SP3 includes many fixes that are necessary and important.
  SP3 must be installed before installing the audio driver.

• Update BIOS and Tecra A9 - no sound with Win 7

  Hello

  I installed Windows 7 from a Tecra A9 laptop and everything works fine except the sound. Sound card for Windows 7 driver is already installed. The speakers and the microphone is detected. While playing music in sound devices the green bar under the speakers raises up and down, but I can't hear anything.

  I read that the update of the BIOS can help, but it does not work under Windows 7, with a Live CD of Windows XP or in Windows XP Mode for Windows 7.

  I don't want to reinstall Windows XP.

  -Does anyone know how to get the sound working properly?

  Have you checked it with headphones?
  Have you noticed the same thing?

  To be honest I don't think THAT BIOS will change anything on this subject. If the audio driver is installed correctly, check that all the settings in Windows and also in Audio DD Realtek Audio Manager.

• Tecra A2 - no sound under Win XP

  To cut a long story short, I installed a registry cleaner via a usb key.

  After running the cleaner, uninstall unused programs too, the cell phone has become fast enough but audio disappeared I accidentally uninstalled the Sigmatel AC97 driver. However I couldn't reinstall the driver because of an error message that I am getting.

  Without a cd to XP, I tried a system restore and proceeded. I managed to install the driver, but again I have no had no noise while the icon and the audio console was in order. I have a scanner and there were a couple of malware in the system that I got rid of.
  Again not sound. I run microsoft fixit audio and the result was: "everything is working perfectly.

  Is there something I can do to regain the sound back without having to reinstall the windows?
  I don't have the CD to install XP in any case.

  Thanks in advance for any suggestions.

  Thanks for the short comments!

• Tecra A10 - 12Z BIOS 1.6 wanted to move to 3, but 'not supported' - W7H32

  There are many problems with this Tecra A10.

  As Windows Xp is disabled, I tried Windows 7, which is too awkward, so I wanted to try the eSATA operating systems. Although I could install Lubuntu on eSATA it would not start (no hard drive inside most) to eSATA, but booted from USB.

  Read in the forum and put the Windows 7 Home 32 disk inside again and downloaded the BIOS update only to get a response "not supported".

  The A10 has a Windows Vista professional sticker slot, is the only OS where this Tecra can get BIOS updated?

  We have no records of Windows Vista.

  Installation of Windows 2000 or XP, it's really a lot of time, even for 9 x.

  The last beta demoCD with eComStation, todays OS/2Warp, works fine on the Tecra, it has Windows integrated 3.11, is that not? Windows 3.11 on a SD card installation must be as fast and as possible. If there are drivers available?

  ReactOS (freeWindowsXP) is usually able to boot, but it is still in the alpha stage!

  As for flat BACK? There are the LiveCD with BACK.

  You can also find Vista LiveCD socalled VistaPE CDs on the net, but their origin is unknown.

  What is the best option? Is there only one option?

  Hello

  > Although I could install Lubuntu on eSATA it would not start (no hard drive inside most) to eSATA, but booted from USB
  I guess that the BIOS does not support booting eSATA port but just the USB port.
  But it's just an idea... that should be checked once more in the BIOS settings.
  Maybe a BIOS update would also help.

  > Read in the forum and put the Windows 7 Home 32 disk inside again and downloaded the BIOS update only to get a response "not supported".

  BIOS update may be run from under Windows system only. But the BIOS update also requires some software additional Toshiba which depends on the system.

  In the case of Windows 7 or Vista, the value of added Toshiba package must be installed. In the case of Win XP, you must install the package of common Modules.

  To be honest I don t understand what you want to do
  Tecra A10 is a great unit. I have the successor called Tecra A11. I use Win 7 and its really awesome OS. Much better than the beginning of Win XP

• Re: Tecra A10 - 1 5, Windows 8 is not compatible?

  Dear Sir
  Windows 8 upgrades very well for example drivers etc for this model you
  Ian

  Hello

  No, Tecra A10 is not only win 8 supported phone model.
  But this does not mean that you can not install the 8 Win.

  You can install Win 8 on Tecra A10 but you will need to find the Win 8 driver for your own hand and maybe you will get not all drivers Win 8 However, 8 Win would go.

• Tecra A10 - change of resolution with Docking Station problem

  Hello

  I own a Tecra A10 - 14Q and I like it a lot - it is a very beautiful piece of hardware, including the functionality of UMTS.

  When the Tecra is moored to the dock Express, and the external monitor (Samsung SyncMaster 22 "with resolution 1600 * 1200) is on defining the Office to be cloned on both screens, passes resolution of 1280 * 800 on the Tecra to 800 * 600 as"best resolution.

  I tried Intel and Mobility Center graphics settings, but I can't find a way to set I want to keep the resolution 1280 * 800.

  Suspicion to do so automatically is welcome. I found that a program that now lies on my desk that I run so it redefines the resolution to 1280 * 800, but I would like to stress that resolution remains just that it is.

  Kind regards

  YaGru

  Hello

  It's not easy to say why the resolution automatically decreases

  But sometimes, if the external monitor would be connected to the Tecra A10 directly without using the Express Docking Station?

  Otherwise the problem could be linked to the dock Express (Replicator of port express?)

  Maybe the 1600 * 1200 resolution on external monitor is too high for the express port replicator and so there are some questions which s my personal suggestion

• Tecra A10 erratic mouse then freezes when serial port used for something else

  MT Tecra A10 was beautiful, but has developed a growing problem. It is running win7 ultimate. When you connect anything serial port wise it blocks indicating the Mouse / touchpad. USB mouse feezes completely, 98% frozen touchpad series same happenes when connecting via a usb emulator. Software on the laptop using series includes RS logix, perfect Omron CX1 Motion and NQ Designer, that said that they worked, can anyone guid help me pls.

  See you soon

  Martyn

  Hello

  Eventually, the software that controls the serial port or the device connected to the serial port is not fully compatible with Win 7.
  I think that this should be checked first.
  Maybe one of you should look for the Special Forum of the manufacturer of the software for more details

• Can I use Tecra A10 OS disk to install the OS on Tecra M10?

  I have a tecra A10 complete with Windows Vista Business installed (and saved in an image using Easeus Todo backup file

  However I also have access to a Tecra M10 entered without an operating system, although the sticker COST (product key) is the same for a windows Vista Business.

  My question is: would my Windows Vista Business backup work A10 on the M10 (i.e. would it load hard disk M10 and then to work properly)

  If someone can advise on this subject I would be grateful if you please

  Best wishes
  Ian

  At first, I must say that Toshiba recovery image created separately for each laptop model and it is 100% created to work on the specific model. Why?
  Each laptop model has different hardware platform and all the drivers, tools and utilities for some models are part of the recovery image. These recovery images are also tested.

  Generally if the two models have the same hardware platform (hardware) it can be used.

• Re: Tecra A10 (PTSB0A-020001) - need webcam driver for Win 7 x 64

  I can't locate these were? I tried vista x 64 does not, any help would be great

  Tecra A10 PTSB0A-020001 webcam driver for win 7 x 64 build 7600

  I m wondering really Vista driver won t work properly.
  Try please install THIS driver support European page.
  I hope that it will work.

• Tecra A10 - 13I (PTSB0E-01400XFR): cannot use 8 GB of RAM

  Hello

  I'm trying to upgrade the memory on my TECRA A10 - 13I with windows server 2008 R2, I am upgrading from 4 GB to 8 GB.

  My BIOS detect 8 GB, see Windows my 8GB (2 x 4 GB) of RAM, but I can see in "8.00 GB (3.87 GB usable)" system properties When I run the application you "Resource monitor", I see 4233 reserved material MB. Finally, if I use a VM with 4 GB of RAM, the virtual machine cannot use this reserved memory and crashes.

  I have read this thread: [http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=54112&tstart=0 | http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=54112&tstart=0]
  I tried to update my BIOS and changed Advanced Startup Option "Maximum memory", but no change to my memory.

  Thank you
  Jonathan

  PS: Sorry for my poor English :)

  Hi mate

  TECRA A10 - 13I is certainly capable of that means you can use 2 x 4 GB RAM RAM 8 GB.

  What is the report DirectX?
  Check the value of memory here. In order to access the DirectX, you must use the command * dxdiag *.

  Greetings