TECRA A3 - started as disconnected connected LAN cable

Similar Questions

• WNDR3700 starts so that the connected lan cables.

  Hi people,

  I have a wndr 3700 for a long time. Lately, every time I wanted to turn it off, and return is on, it does not start unless I have unplug all lan cables and wait for it to start. It is very stange, because there is no problem with it. Once it starts, it works fine. but I have to disconnect the cables and wait for the boot sequence.

  no idea how I can fix this problem?

  Thank you.

  I think I did. I flashed with ddwrt and now it starts at each connection to the local network. so it was probably a software issue or a hardware but ddwrt can handle or ignore it. I'll try the official fw to see if the old fw was just tired :)

  Thank you all.

• Satellite Pro U300: Error Message: cable is disconnected, but Lan cable is connected

  Hello

  I have problem with interface ethernet (wired) in my Satellite Pro U300. I use in many places (home, office, customers) and when I restore in sleep or hibernation mode interface ethernet shows that the * cable is disconnected *, despite the connection of the cable * is * connected and works perfectly with all other devices, laptops and PC.

  The switch also shows that the there no signal link. But re - activate the malfunctioning ethernet port, just disable the ethernet interface and then after 5s (1 s is too short!) turn on.

  Then a baloon in taskbar window indicates that there are 10 Mbit/s link, but actually, the link works at 100 Mbps (I can see it in the connection status window and the ethernet LEDs switch). This is the only laptop that has this kind of problems.

  I have the latest version of the installed ethernet 5.664.205.2007 driver on Win XP SP2.

  Is it possible I'm getting rid of turn on interface ethernet several times per day (except change laptop)?

  Hello

  I put t have a real solution but I have a few proposals of solution

  First of all, you should check in Device Manager if the network card has been properly recognized. The Ethernet card should be listed under network without any yellow exclamation point cards.

  If the network adapter has been properly recognized, then the next step should be checking the properties of the LAN connection.
  There, you should check the properties of the TCP/IP protocol.
  The settings such as IP address automatically get & address of DNS server automatically get must be marked.

  Greetings

• Often disconnect connection LAN - Satellite A300 PSAG8E

  Hello

  I am facing problems of disconnected frequently connect to the LAN in my notebook
  I get a warning on the Microsoft ISATAP #5 map icon.

  If you want to discuss about some questions please phone model poster and info on the preinstalled OS.
  Do you use the laptop with the factory settings?

• Satellite A300 - lack of sleep/hibernate with connected LAN cable

  Hello

  I've owned a 1FZ A300 for a few weeks and unfortunately it did not go into sleep mode or hibernation while the ethernet cable from the router is plugged in, even with other programs stopped.

  (Previously, I used an other non-Toshiba notebook with no problem)

  I tried upgrading the BIOS as suggested in other threads, but it is newer that what is available on the Web site.

  Everyone knows about this problem?

  Any advice would be greatly appreciated.

  regs
  Mike

  Hello Mike ;)

  I wonder what you do with your laptop. I have Satellite A300-1LI in front of me and standby/hibernation work correctly. Last week, I tested the portable functionality under Windows XP Home edition and I didn't notice any problems under Windows XP Home edition either.

  Now I have Vista (recovery image) once again and it works well. Can I use FN + F3, F4 with no problems.
  Please note that my Satellite A300 is permanently connected to the local network. I use it for my work.

  The question is: have you noticed that on the first day?

• Tecra A6 does not connect to internet with lan cable

  I got a new Tecra A6, (windows xp) which is barely a week. fine, except that when I connect my router to the laptop computer with lan cable broadband, I am not able to connect to the internet. When I connect the cable to the internet, I'm getting the lan icon works correctly, but when I open a browser page, it says no connection.

  considering that wireless works fine.

  help appreciated.

  Check the firewall settings.
  Maybe the firewall is on and does not allow you to open Web sites.
  Please also check the internet option-> connections in the

• After I start my computer dell laptop I connect the LAN cable to run internet ON my laptop but it doesn't detect LAN cable

  Hello..

  After I start my computer dell laptop I connect the LAN cable to run internet on my laptop but it does not detect the LAN cable, using the ultimate32 bites. (But if I connect LAN canble then start computer it works fine)

  Hello

  1 windows operating system is installed on the computer?

  2. do you think that no matter what error message in Device Manager? If Yes, what is the full and exact error message?

  3. What is the number of brand and model of the computer?

  Method 1:

  If you are using Windows 7, I suggest to see the link and try to run the troubleshooter and check if it works.

  Windows wireless and wired network connection problems

  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  The link applies to the Windows Vista and Windows 7 operating system.

  Method 2:

  Check the link and try using the network troubleshooter to fix the problem.

  Using the troubleshooter from network in Windows 7

  http://Windows.Microsoft.com/en-us/Windows7/using-the-network-troubleshooter-in-Windows-7

  See also:

  Use Network Troubleshooter event logs to solve network problems

  http://Windows.Microsoft.com/en-us/Windows7/use-Network-Troubleshooter-event-logs-to-solve-network-problems

  Method 3:

  See the link and check if it helps.

  Why can't I connect to the Internet?

  http://Windows.Microsoft.com/en-us/Windows7/why-can-t-I-connect-to-the-Internet

  Let us know if it helps.

• Lost my wireless with a lan cable connected

  I have an old Airport Extreme Base Station. Now I connect a LAN cable to connect the German Entertainment TV.

  The TV works and I continue to receive the signal from the airport but without data internet aka.

  If I disconnect the cable internet wireless lan working again?

  Where is my mistake?

  Dirk best

  Give us a screenshot of the configuration of EI when not working WiFi... and when it fails.

  Please click the airport icon so I can see the analytical parameters.

  Like this.

  

  What model is your AE?

  You can find the number of A1xxx on the basis or you can hold down the option key and double-click the icon in airport utility.

  The actual model will be displayed on the summary page.

  Then

  

  This modem do you have? Brand and model please.

  Is what type of broadband services?

• Toshiba NB550-111 - no connection if the LAN cable is more than 2 metres

  Hello

  My newly purchased Toshiba NB550-111(Windows 7 Starter Service Pack 1) has problems with the LAN card.
  If the LAN cable is more than 2 meters, no relation to Allied Telesyn switch (no indicator led on the switch, 2 other desktop computers already connected). I tried not to connect in a different port (one used previously by one of desktop computers), no connection. I tried with 3 cables, still no results.

  Cables (cat5E, so important) have been tested OK before with a cable Tester, and I use both of them without any problem with another 2 desktop computers at home. I set another cable (5 m long, newly purchased) and tested for connectivity. It works very well with the other two offices, no results with the netbook. I tried with adapter it works, I disabled ' energy efficient ethernet "NIC, still no connection properties page. It only connects if the cable is less than 2 meters. I tried to connect the netbook directly to the DSL router, still no connection with a longer cable.

  The device is reported by windows as work very well, and the test Toshiba utility ends there is no problem. Windows I configured in the Control Panel, the Plan balanced for maximum performance in the power options, still no results.
  Any ideas, please?

  Now maybe stupid question but what is with WLAN? You don t want to use WLAN?

• Satellite A20-S103: LAN cable disconnected

  Hello

  I can not access my LAN or internet.
  I use a Satellite A20-S103 with a Realtek RTL8139/810 x Family Fast Ethernet NIC

  When I connect the Lan cable to the LAN port, the message "LAN Cable" disconnected.
  The same message is displayed using connectivity doctor ConfigFree.

  I have changed several cables, used cables that worked on other computers and the message still there and no access to the router/modem.

  Near the LAN port LEDs are not lightning (or orange or green, no)

  I already read messages here in the forum (and other forums) and I can't get the ethernet card works.

  Do you think the problem is with the card or the operating system.

  Can you help me?
  Sorry for my English

  First, check to see if the network card has been recognized in the Device Manager.
  Under network adapters, you should see the LAN card.

  If there is a yellow exclamation point near network card then the driver has not been installed correctly or there is another serious error.

  In the first case I recommend the withdrawal of the LAN card from the Device Manager and after new reboot, you should try to reinstall the driver downloaded from the Toshiba page!

  In addition, you must set TCP/IP parameters automatically because the router assigns the IP address automatically.

  Please check and report the results

  Good luck

• Tecra M3 has ceased to connect to the internet with cable

  I have an old laptop Tecra of 3 year (out of warranty).
  Last week, he stopped to connect to the internet with a cable. I tried several cables and jacks. No idea what to do?

  LAN card is entered correctly in the Device Manager?
  LAN port has two leds, green and orange. Green LED is turned on when you connect the LAN cable?

• PROTECTED M800 auto boot up after connected with lan cable

  Hi all

  I have a problem with my laptop Toshiba Portege M800. I decided to connect a lan cable directly on the cell phone instead of using the wireless feature. However, when I shut down the laptop, it will automatically start upward. But after I unplug the lan cable and stop working properly. Can I know the config to make the laptop does not auto boot up after I closed the laptop with the lan cable connected to it.

  Hello

  I think that the boots mobile upwards because the wake on LAN in the BIOS option is enabled
  Please disable this option (in BIOS), save the changes and restart the device

  Then test this new!

  Welcome them

• HP laptop: unable to identify the lan cable connection

  Microsoft Windows [Version 6.3.9600]
  (c) Microsoft Corporation, 2013. All rights reserved.

  Rodriguez C:\Users\anshu > ipconfig/all

  Windows IP configuration

  Name of the host...: fadiga
  Primary Dns suffix...:
  Node... type: mixed
  Active... IP routing: No.
  Active... proxy WINS: No.
  ... DNS suffix search list: Working Group

  Ethernet connection to the Bluetooth 2 network card:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Device Bluetooth (personal area network)
  #2
  Physical address.... : B0-10-41-80-AF-1E
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Local Area Connection wireless LAN adapter * 5:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Hosted network virtual card
  Physical address.... : B0-10-41-80-AF-1E
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Local Area Connection wireless LAN adapter * 2:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Microsoft Wi - Fi Direct virtual card
  Physical address.... : B0-10-41-80-AF-1F
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes

  Wi - Fi wireless LAN adapter:

  The connection-specific DNS suffix. : Working Group
  ... Description: RT3290 Ralink 802.11bgn wireless adapter
  Physical address.... : B0-10-41-80-AF-1D
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::e809:c01a:618f:7b5a %4 (Preferred)
  IPv4 address...: 192.16.137.4 (Preferred)
  ... Subnet mask: 255.255.255.0.
  Lease obtained...: Saturday, June 11, 2016 08:56:13
  End of the lease...: Wednesday, June 15, 2016 12:56:15
  ... Default gateway. : 192.16.137.1.
  DHCP server...: 192.16.137.1.
  DHCPv6 IOOKING...: 78647361
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers...: 10.10.2.2.
  192.16.137.1
  NetBIOS over TCP/IP...: enabled

  Ethernet Ethernet adapter:

  The connection-specific DNS suffix. :
  Description...: Realtek PCIe FE Family Controller
  Physical address.... : 14-58-D0-C5-74-1D
  DHCP active...: Yes
  Autoconfiguration enabled...: Yes
  Address IPv6 local link...: fe80::3070:15bf:b1ee:daab %3 (Preferred)
  Autoconfiguration IPv4 address. . : 169.254.218.171 (Preferred)
  ... Subnet mask: 255.255.0.0.
  ... Default gateway. :
  DHCPv6 IOOKING...: 51665104
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers: fec0:0:0:ffff:1 1%
  FEC0:0:0:FFFF:2 1%
  FEC0:0:0:FFFF:3 1%
  NetBIOS over TCP/IP...: enabled

  Card tunnel Teredo Tunneling Pseudo-Interface:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Teredo Tunneling Pseudo-Interface
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Card adapt 6TO4 tunnel:

  The connection-specific DNS suffix. : Working Group
  ... Description: Microsoft 6to4 card
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes
  IPv6 address: 2002:c010:8904:c010:8904 (Preferred)
  ... Default gateway. :
  DHCPv6 IOOKING...: 704643072
  DHCPv6 DUID customer...: 00-01-00-01-1C-FA-E4-80-14-58-D0-C5-74-1D

  DNS servers...: 10.10.2.2.
  192.16.137.1
  NetBIOS over TCP/IP...: disabled

  Tunnel adapter ISATAP.workgroup:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. : Working Group
  ... Description: Adapter Microsoft ISATAP #5
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Tunnel adapter isatap. {74914F29-E819-4DEB-8CC2-D37CBFD70F3B}:

  State of the media...: Media disconnected
  The connection-specific DNS suffix. :
  ... Description: Adapter Microsoft ISATAP #6
  Physical address.... : 00-00-00-00-00-00-00-E0
  DHCP active...: No.
  Autoconfiguration enabled...: Yes

  Rodriguez C:\Users\anshu >

  On the lan cable connection, it says as unidentified network.

  That's what I have to type the command ipconfig/all.  I tried to reinstall drivers recvoery as Manager, but no results. It worked without problem until now

  @anshu645

  Home networks typically use a form any of 192.168.x.x

  For example:

  192.168.1.14

  Found in your example:

  192.16. 137.1

  Also found:

  Autoconfiguration IPv4 address. . : 169.254.218.171

  +++++++++++++++++++++++++++++++++++++++++++++

  I suspect that the installer with your home network router is misconfigured and the network can't find a viable (useful) DNS address to use for the purpose of ISP Internet Service (ISP) connection.

  Please see the following:

  HP PC - troubleshooting wired home networks (Windows 8)

  HP PC - Troubleshooting wireless network and Internet (Windows 8)

  When you see a post that will help you,

  Who inspires you, gives a cool idea,

  Or you learn something new.

  Click the 'Thumbs Up' on this post.

  My answer-click accept as Solution to help others find answers.

• The blue windows screen Driver_irql_not_less_or_equal 7 when connecting the LAN cable?

  Hi all,
  I just want to ask how to solve Driver_irql_not_less_or_equal windows 7 blue screen when connecting the LAN cable?
  pls help me...
  Thanks in advance...

  We need the DMP file because it contains the single record of the sequence of events that led to the accident, what drivers have been loaded, and what has been loaded.

  You may be able to get the DMP files without crashing by booting in SafeMode (F8) with networking.

  If you are overclocking stop.  (chances are that if you are unsure if you are, you are not)

  To allow us to help you with symptoms BSOD on your computer, download the contents of your folder "\Windows\Minidump".

  The procedure:

  * Copy the contents of \Windows\Minidump to another location (temporary) somewhere on your machine.
  * Zip up the copy.
  * Join ZIP archive to your message by using the button (attachments) "trombone".
  * Please download to a service like Skydrive or "Rapidshare" to share files and put a link to them in your answer.

  To ensure the minidumps are enabled:

  * Click Start, in the search box, type: sysdm.cpl, press ENTER.
  * On the Advanced tab, click Startup and recovery... Settings button.
  * Make sure that automatically restart is unchecked.
  * Under the writing debugging information header, select image partial memory (256 KB) in the list box drop-down (varies from 256kb).
  * Ensure to that small Dump Directory is listed as % systemroot%\Minidump.
  * OK your way out.
  * Reboot if changes have been made.

  Please also run MSinfo32 and download the output as well.

  To run MSinfo32 please go to start > run > MSinfo32
  Go to 'file', 'save' and download the PDF is saved with the DMP
  (Instructions for XP, Vista, Win 7, Win 8)

• Satellite P305D-S8900 - LAN cable is a schooner of connection

  Hello

  I can connect my LAN cable to my computer and the computer will detect and indicate that it is there.

  The problem is that none of the software on the computer seems to see that there is a link. Internet connection screen says that the LAN cable is a schooner of connection. I tried everthing I know so he can work with no sucsess.

  PS. I use Vista and I know little about it Vista.

  Hello

  First check to see if the network card is recognized and if the LAN driver has been installed correctly.

  It is the as-installed LAN card properly then you should check the settings of the network adapter's TCP/IP protocol.

  The properties of TCP/IP all the settings such as IP address, gateway, DNS must be set to automatically get

  Also please check if a firewall, antivirus, etc apps don't lock access to the local network.