Tecra M9 does not recognize the SDHC 4 GB
Tecra M9, Windows XP
The internal card reader does not recognize the SDHC 4 GB (provider: "extreme memory"), being inserted in camera or PNA not connected via USB, no problem to read or write to the card.
No idea how to get the card to work with this card reader?
Hello
I have an idea.
I think that the SDHC 4 GB card is not recognized because a Microsoft patch is not installed on your XP operating system.
Microsoft has released this document which should help you to solve this problem:
[Hotfix for Windows XP that adds support for a capacity of more than 4 GB SDHC cards | http://support.microsoft.com/kb/934428]
Good bye
Tags: Toshiba
Similar Questions
-
Tecra S5 does not recognize the SDHC 4 GB micro card
Hello.
I have a 4 GB microcard SDHC and the reader of my laptop does not recognize the card...
Help.
GR Arno
Hello
Are you sure that this laptop supports this type of card?
As far as I know THAT these cards are compatible:
Card SD - 8 MB - 2 GB
SDHC - 4 GB card
-16 MB - 2 GB xD Picture card
Memory Stick - 8MB - 256MB
Memory Stick Pro - 256 MB - 2 GB
MultiMediaCard - 8 MB - 1 GB
miniSD (with SD adapter) - 32 MB - 2 GBOnly the SDHC card and not SDHC micro card is supported
Concerning
-
Tecra 8200 does not recognize the RAM in Slot B
Since a few days my Tecra does not recognize the RAM Module in Slot B. Before everything was fine. I have 2x256MB Modules. I was wondering why my Tecra becomes slower, the last days, and then I saw that I have now only 256 MB of RAM. I have change the slot Modules A to B. I checked also the two modules of RAM with MEMCheck. Both are ok! Just at the moment where I put a RAM for Slot B and none in slot A my Tecra won't start! If I insert the two module my Tecra boots but with just 256 MB of RAM.
Is there another solution then buying a new laptop? Is my Mainbord damaged?
I was so contently with my Tecra ;-) so far
The slot B is probably defective. Only solution for me is to buy compatible 512 MB module and use it in A slot. According to specification for laptop, your device can handle with max 512 MB of RAM.
-
Tecra M1 does not recognize the DVD drive after replacement
I am trying to install a new drive CD-RW/DVD-RW on a Tecra M1; However, when the computer does not recognize the drive.
Is there a solution to this?
Thank you
Colin
For me it s case.
I would say that the BIOS can't handle the new player properly because of the wrong master/slave/c-salt settings
Readers slim for computers laptops support setting master/slave/c-salt settings and these settings can only be changed by changing the rider as on desktop drives.
So it is very important that you purchase a compatible player and supported because disks with incorrect settings will not work.Before buying a car, you should ask the service provider to Toshiba for a caught player supported and compatible
-
TECRA 8200 does not recognize the second module memory
Hi, I have a problem with one of the TECRA 8200. The machine only recognizes the first module and not the second 128 M I tried form to upgrade memory up to 256 M. module is compatible because it works without problem with an other TECRA 8200!
I updated the bios to version 1.6 but there is no way: the PC does not recognize the second module!
What can I do?
Hello
Perhaps is the second memory slot is faulty. Put this add-on in the first slot and check again.
-
Tecra 8000 does not recognize the new HARD drive
I read on this forum and Google search, but nothing helped.
I think the disk on Tecra 8000 (Pentium II, 266 Mhz) is "dead".
I tried to replace it with another laptop to see if that would work.The laptop does not, even if I put just like the original.
Y at - it somehow special or what I have to change something in the Bios?Hello
Don t need to change BIOS settings
As long as you use the compatible HARD disk, the BIOS should recognize the HARD drive automatically without big problems
What drive did you use? What size, interface, etc.The Tecra 8000 is an oldie and I think that you could use only the 4 GB; 6 GB; 9 GB; 10 GB; 14GB IDE hard drives.
More large hard disks would be not recognized by the BIOS.
-
Tecra S11 does not recognize the Art store
Hi guys,.
I have a new S11 with Win7, 64-bit and a disc Toshiba StorE art. The S11 will not see the drive, but my other machines running XP and Vista have no problem to recognize.
Any ideas on how to access the drive with the S11? Input much appreciated!
I recommend you to follow:
-install the OS using the Toshiba recovery disc or HARD drive recovery procedure
-Install all updates from Microsoft
-reconnect the HARD driveMust work on Win7 32/64 bits.
-
Tecra M9 - does not recognize the 320 GB HARD drive
Hello @ all,
I tried to install the HARD drive, but it seems to be not recognized by the BIOS. Any chance to get this problem resolved?
With Acronis Disk Man. I get an error message: No. HDD installed!
BIOS version is 1.80, HARD drive is a Seagate ST9320421ASG (Momentus 7200.3 320).Thanks in advance
Hello!
Have you tested the HARD drive in a laptop or in an external enclosure? Maybe it s faulty.
Or you test another HARD drive in this notebook.Normally a 320 should work in Tecra M9.
There is a new version of the BIOS on the Toshiba, but I doubt that the problem of the article, but try to update.Good bye
-
Tecra S3: Installation of Vista does not recognize the HARD drive
I try to install Vista Ultimate on my Tecra S3, but installation does not recognize the HARD drive.
I tried to find the driver for Vista for my computer, but not found RAID.
Tried it with XP drivers, but no longer works.Do you have an idea where I can download Vista drivers for RAID?
THX
Hello
Your suggestion is good. The Tecra S3 supports the RAID, and the RAID driver is required to install the OS on the HARD drive.
On the European driver Toshiba page I found a RAID for XP driver.I put t know if this driver will run under Vista, but I recommend to test.
The RAID XP 1.3.8.0 driver version can be downloaded from this site:
http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=EUPlease note; You can store the RAID driver on an external USB and Vista should recognize it!
Good luck
-
Power mac g4 does not recognize the DVD/CD drive. It has worked very well in Leapard
I just newly installed Tiger on my PowerMac G4, and now it does not recognize the DVD/CD drive. I did all the updates and it does not see the DVD in the DVD drive. It works perfectly before a new clean install DVD of the Tiger.
What is your indication that the DVD is not recognized?
Run the utility disc with the disc in the optical drive. The drive will appear in the sidebar of disk utility?
I did all the updates and it does not see the DVD in the DVD drive.
If you put another type of disc in the optical drive, as a music CD, it is recognized?
-
I uninstalled flash on my mac now youtube videos will not play.
the error says safari does not recognize the video formats available.
Reinstall the Flash Player... Why did you remove it?
Barry
-
I have a My Passport to the top by car and I get error messages on this to be ejected (although it was still connected). Now my computer does not recognize the drive. All solutions?
Drive, interface in the crankcase of training controller, or the USB port or the cable may be faulty.
-
Siri does not recognize the voice.
My Apple TV remote Siri works fine, but only of Siri does not recognize the voice. I just bought last month. No gross State aid.
Are you pressing the button of Siri (micro) when you talk?
Have you enabled Siri in settings > general > Siri?
If so, then try a reset by unplugging the power cord for 30 seconds.
-
ITunes does not recognize the phone
IPhone SE, Windows 10, update ITunes, McAfee
Connect the phone to the computer and the window phone company recognizes the phone immediately. I close the phone company of the window and open ITunes. ITunes does not recognize the phone. I have the menu bar, select file > currencies, all the options are greyed out.
Disable McAfee, and then try again.
-
Apple TV does not recognize the Apple wireless keyboard
My Apple TV (4th generation) does not recognize the wireless Apple keyboard I want to make a pairing. All my other devices (Mac, iPhone and iPad) recognize the keyboard. This should be done automatically on the Apple TV, but it's not. The Apple TV has acknowledged the Apple TV remote and paired with her. Any help would be appreciated.
Thank you
Ken Templin
I paired a non-Apple clone keyboard and it was somewhat capricious. You go to the remote controls and devices-> Bluetooth, enable matching on the keyboard, and it should appear in 'other devices '. You select and enter the number to validate. It requires no tvOS 9.2.
Maybe you are looking for
-
HP 12 c: HP 12 c error 5
I get an error 5 when trying to make a TVM problem I was wondering if anyone else has experienced this and/or may have some tips. I entered PV = - 3000 PMT = 50 FV = 0 I have = 10.5 calculate for n and I get error 5 If I make the following modificati
-
Full computer stuck on the login screen
Original title: complete computer freeze on connect on the screen... nothing I tried works critical need help I am running windows xp and for some reason any (probably a major virus or main registry errors) when I try to log on to my computer nothing
-
Close / sleep on vista computer functions to restart instead
When I try to select "shut down," the computer still restarts instead, but then on the second try, it always stops. Also, when I close the laptop (that I have designated for sleep) or select the day before on the menu, he stops and restarts. This pro
-
[REQUEST] Different images for each parent of the field of the tree?
How can I provide different pictures for each parent/root of the field of the tree?
-
Error USB device (this device cannot start. (Code 10))
When I try to use my USB device, it displays error code 10 is to say that the device cannot start, I use win7 ultimate 32 bit OS