Tecra M9 - Windows 2000 ACPI

Similar Questions

• Tecra S3 - Windows 2000 hangs on reboot

  Hi all

  I have a Tecra S3 dual boot Windows XP and 2000, with the correct RAID driver installed for each of them.

  In Windows 2000, it hangs for a reset. It is necessary feed the computer works in order to complete the reset.

  This problem does not occur in Windows XP and BACK. Is there someone else by using Windows 2000 with this model?

  Thank you

  Rubens

  Hello

  Well, it's not easy to say why this problem occurs. I assume that you have installed the W2k since the original Windows CD. In this case, it is very important to install the driver Toshiba, tools and utilities in the correct order.
  On the Toshiba download page I found a statement of installation for W2k. This list gives you a good driver installation information. Please see this document.

  Good bye

• Tecra S1 with Windows 2000 Professional, Modem error

  I have a problem.

  I installed Win2000 Prof on my Tecra S1.

  I have a problem with the modem.

  I have installed the appropriate driver and the modem in the devices is OK, but if I do a check for the modem PROPIETIES it returns: OPENCOMM: could NOT OPEN. (impossibile open carried her)

  What can I do?

  Thank you

  Hi lukager,
  I ve heard that you must consider an order of Installation to install Windows 2000 without problems.

• Update my Tecra 8000 from NT 4.0 to Windows 2000

  When I update me my Tecra 8000 NT 4.0 to Windows 2000, my Setup stopped and I got the message that I had to remove the Configuration Interface for system Toshiba driver. What is going on?

  To enable NetMeeting in Windows XP, you must go to the start menu and select run. Conf and click OK. After the NetMeeting configuration wizard starts, click Next. Enter your personal data and click Next. Select Directory list options, and then click Next. Select the media for your connection and click Next. Set up shortcuts for your convenience options, and then click Next. Click next to configure the volume options and click Next and then click Finish. To start NetMeeting, NetMeeting Startup session (e.g., run conf.exe again to start the application or select the shortcut in the start menu or desktop), click the phone button and enter the IP address of the machine you want to connect with.

• Tecra M2 mapping of the keyboard in Windows 2000

  Hi all

  I have a Tecra M2 on which the WinXP was removed and replaced by a new installation of Windows 2000 SP4 (I prefer not to go into detail as to why this took place).

  My problem is that the keyboard mapping is not correct under Win2000, for example if I press shift + 2 I get a @ and not a '. '. The problem exists with almost all the characters of Maj (' |,-,', ~,', ', @, #, etc..).

  Note that I don't use any software that remaps the keyboard.

  Does anyone know how this bee fixed?

  Thank you very much

  Hello

  I have the same problem on my laptop, but I don't have time to look at the problem until I saw this ad...

  Here is the answer for Windows XP, I guess it's the same for Windows 2000, because the systems are similar.

  Under start/setting/control panel, you will find the icon "regional and Language Options". Double click it and you get a new window. Select the folder "Language" then "Details". A new Windows pop up and from there you can select 'Add' services 'install '. Select your language to enter the menu drop-down, then click on 'OK '. Ensure that the value "default input language" is correct, then click 'OK' and click on 'OK '.

  Normally, the operating system needs to restart to set the hardware!

  Your keyboard should work correctly after the next system startup.

  Let me know if it works for you

  Rusty

• Tecra S1 under Windows 2000 Professional external display problem

  As I can't answer in the original thread (1831), because it is locked, I put here my answer to the answer of the Quad.

  Quad first wanted to know if we have installed the Tecra S1 on a recovery CD.

  No, we do not have. We have created an image that consists of an unattended installation. It is installed from a Windows 2000 RIS server.

  Quad also said that the Fn + F5 is enabled after the installation of the utility Hotkey for display devices.

  We downloaded the hotkey utility, but when we tried to install it we got the error message you "Driver not found" and suspended installation. We have installed as a user with administrator privileges.

  We do something wrong, or this utility owes something to be installed as well?

  Kind regards
  Harro Hofman
  Material specialist

  The Netherlands.

  Hi again Mr. Hofman,

  First of all I must tell you that this is a typical problem. AFAIK Tecra S1 comes with the Professional Windows XP Home edition and optionally with W2000 professional. This two OS has been tested and Toshiba offers all drivers and tools to Toshiba download website.

  It will be interesting how you created this image. What was the basis for this image? You are installed to the first completely Tecra and after created image?

  Have you had problems before the creation of the image?

• Tecra 8200 - works very well under Windows 98SE, but not on Windows 2000

  Hello

  I've updated my Tecra 8200 for Windows 98SE and Windows 2000.
  Windows 98SE, wireless connection works very well and I was able to access the internet through my SMC Barricade router.
  But on Windows 2000, this no longer works.
  The connection to the router is ok, but I am unable to connect to the internet or to the page web administration of the router.
  The Toshiba Wireless Client Manager provides the following information:
  Status:
  ------
  Connected to the network: SMC
  Connection: Excellent
  Access Point name:
  Channels: 2
  Encryption: on

  ----------- Warning ----------------
  Impossible to communicate with the AP.
  Please check the encryption and IRQ.

  Yet once, I insist on the fact that under Windows 98SE, everything worked well... an hour ago...

  I am running Windows 2000 SP4 with the latest updates.
  Could someone help?

  Thank you

  François

  Hello

  Thanks for the solution. I hope that the installation of Windows 2000 Service Pack 1 helped.

  Good bye

• Tecra M2V crashes during the Windows 2000 format

  I'm working on the installation of Windows 2000 for a laptop Tecra M2V in my school. The installation process crashes when the disk has reached 6% format. It is always in the same place that the deadlock occurs. Is there a way to get around this, or can I change a setting in the bios Setup? Any help appreciated.

  Hello

  Not easy to say what can be the problem, but if the formatting process always freezes at the same place I assume that there is a problem with the HARD drive sector faulty or bad. I recommend you to check the HARD drive using a tool. Google a bit and you will find many tools for free.

  Good bye

• Error message at startup in Windows 2000, "Tcmsvr.dll, the file is missing.

  We get the same error messages three times at the start of Windows 2000 on some of our companys computers: "Tcmsvr.dll, file is missing. Computers are Tecra s1 models.

  What driver Toshiba is this related to?

  Hello

  I studied a bit and it seems that this file should be placed in the system32 folder.
  In my opinion, this file is part of Toshiba common modules.
  I m not 100% sure, but you can try to refresh (restore) the common modules.
  Maybe this will help.

• Cannot install Windows 2000 on SatPro 4600

  Hello

  I have a SatPro 4600, earlier, I got ACPI Bios error when you try to start Windows.

  Is it possible to disable ACPI in the Bios, I couldn't find any option in ACPI Bios 2.60 to turn it off.

  The I formatted the hard drive and try to install Windows 2000 from scratch. But for Setup is copying files to start the installation program, it comes up with an error message.
  "Setup cannot copy the file"File_name"

  And will not let me continue with the Setup program.

  Help, please.

  Hello

  I can't help you much about it, but maybe this article can help you. Check http://support.microsoft.com/kb/319344/en-us

  Good luck!

• Satellite M30X windows 2000 installation problem

  I noticed ribooth has also posted a message with the same problem... but I haven't seen a real answer. The problem: if I try to install Windows 2000 Professional (including SP2) on my satellite M30X-130. The windows 2000 Setup program crashes with a "page in a no fault paged area" in acpi.sys just at the moment where the status in the status bar has been changed from windows 2000. If I press F7 during startup, acpi support is disabled and no page error occurs but the windows 2000 installation hangs on "the first screen" where you should be able to start, stop and? installation. There is no additional hardware installed and I'm unable to partition and format the HD with W2k. If I do it with win98 and create a FAT32 partition and try to install w2k on it I get the same ' page in a no fault paged area "acpi.sys error. Any suggestions to fix this?

  Hello
  Make sure that the system BIOS and other hardware is compatible with Windows 2000.
  This article may also help.

  HOW to: Specify a specific HAL or a third party during the installation of Windows
  http://support.Microsoft.com/?ID=216251

  Good bye

• Satellite 1605cds: RAM has not reported in Windows 2000

  Hello

  I have a 2nd hand Toshiba Satellite 1605cds/4.3 (amd k6-2 450 mhz basic system).
  It has 32 MB of ram on board and a dimm slot - so put in a memory of 128 MB.

  But I read this Web page:

  http://fandelem.com/toshiba2.html

  where it says it can be improved with a 256 MB memory module!

  I have it plugged in and it correctly sees 288 MB (32 MB onboard 256 MB on housing) in the bios.
  When I boot from the partition of Windows 98 Second edition, it shows the 288 amount of ram.

  .. .but when I boot on the partition of Windows 2000 Professional, it displays a blue screen saying that the bios is not an improved ACPI bios. It says that I have to push the F7 key during the installation of Windows 2000 to disable ACPI and install HAL.

  But if I remove the 256 MB slot, Windows 2000 starts correctly without any problem.

  I tried to reinstall Windows 2000 by pushing the F7 key during installation, but then Windows 2000 shows that the 32 MB of ram.

  So, what can I do to run Windows 2000 and 256 MB module?
  The bios is the last that can be downloaded on the web page of toshiba.

  Thanks to all and sorry for my English.

  Hello

  According to your description W2k said to update the layer HAL (Hardware Abstraction Layer). In Windows 2000, there are several ways to solve the problems associated with the material (HAL, Hardware Abstraction Layer) Abstraction layer that may occur due to bad detection, an obsolete or non compliant Advanced Configuration and Power Interface (ACPI) Basic Input/Output System (BIOS) or incorrectly installed computer type or manually.

  For more information, please see this Microsoft support site:
  http://support.Microsoft.com/kb/237556

  But as I know Toshiba supports the 128 MB only on this unit and if you want to use more ram you can do at your own risk!

• Windows 2000 Setup error

  Hi, I have a Toshiba Tecra 730cdt I'm trying to install windows 2000. When I get to a point in the proses

  It stops and gives me the following error message:

  Fatal error:

  Setup could not retrieve the ID of the product due to the following error:

  RegQueryValueEx returned for invalid data [type = 1], or the nest has an invalid length [length = 8].

  ***

  Fatal error:

  Setup could not retrieve the Identification of the system product that you are installing

  Support for windows 2000 may be damaged

  Please contacct Product Support

  ***

  Once the system is rebooted, it shows a screen saying that the installation has been restarted and enters this loop hole

  I was wondering how to fix this error because I used a different windows 2000 disk and got THE SAME ERROR

  ANY help would be appreciated!

  How to modify the Config.sys and Autoexec.bat files

  http://support.Microsoft.com/kb/232558/en-us

• Please let me know how to start firefox in SafeMode to my windows 2000 server.

  I installed R-kiosk and now I am unable to remove it. In windows 2000, there is no folder for firefox.
  So please let me know how to start firefox in safe mode on a windows 2000 OS...

  Thank you very much...
  But I just solved the problem. I haven't done

  Start > run >
  "C:\Program Files\Mozilla Firefox\firefox.exe"-safe-mode
  Safe mode started...

• Facebook reports that I use v3.5 of Firefox and Windows 2000 when running on 16.0.2 and XP (upgraded system). where is this info and how to reset?

  the PC has been improved from Win2000 to XP and has all the XP service packs. It also runs Firefox 16.0.2. When I go on Facebook and other pages, it says that I'm on an unsupported operating system (said I use Windows 2000), and I should upgrade my browser to the latest version (said I'm under FF 3.5 or 3.6 FF, can't remember which). i've looked through the registry, but not not found something that jumps. where can this info could be stored that Firefox is looking.

  Try reading some sites say that Firefox is obsolete or incompatible, even if it's the latest version