Tecra S1 beep code then LCD is dark

Similar Questions

• Tecra S1 does not start-> beep code appears

  Hello

  I have a problem with my Toshiba Tecra S1.
  It won't start, just beep like this:
  -Two shorts and a long
  -So, three short films and and etc.

  I can't find out what BIOS and the significance of these beeps.

  Can someone help me?
  Thank you
  Duditz

  As far as I know, it's an Insyde BIOS on the Tecra S1.
  But I thought you wanted to contact the Toshiba service provider?
  Believe me, the BIOS beep code can be read by a technician with a lot more experience as a common user.
  Eventually, you'll be able to read but you don t know what the code means.
  The meaning of the code differs from BIOS and laptop model
  I don t see other than by contacting the guys services

• Beep codes 8 (redirect) it is time to replace the lcd

  Hi guys, I have dell vostro laptop 2520 integer October 2013, the warranty period is over recently I placed a problem where my laptop gives 8 beep codes. I did the test LCD but still healthy.  It's time for me to replace the lcd screen or all can be done without replacing. If this is not the case, how replacement cost. Thanks awaiting response.

  Handsome of Ganesh,

  (India)

  As you have a laptop, better make this laptop in the computer Forum post here:

  http://en.community.Dell.com/support-forums/laptop/default.aspx

  Bev.

• Tecra S1 sends beep codes - 2 short 1 long 3 short

  I suspect a memory problem... I have 256 meg pc2100 memory. I tried switching to machines slot and managed to do the start, but it froze after 2 min.
  Would not restart after only beep codes

  Can someone help me?

  You can try a different RAM? I think that it s a problem with memory, but I don't know m.

  It could also be a motherboard problem, but you should try another memory module first.

• "Beep code" understanding

  Hi all

  I have a 2 years old compact-hp pasario sr5050nx running 32 bit vista premium. From the start, it beeps and does not load vista. I am trying to understand the code. It emits 3 beeps, and then goes a little aaaahhhhhhhhh. Is it a long code or it's just the beeper winding down like a sireen? She does twice. Any help on this matter by someone with experience would be surely appreciated. Thank you!!

  Last updated on August 21, 7: 00 a.m. et

  After several days of listening to all persons named Dakkar, Mushima, Poinyanim, Paripiewa and tastes at HP email and light weight suggestions from here, I thought that my old computer for 2 years ol was dead. HP said it takes less than a new motherboard.  I bought a new and quickly took to Best Buy to get some fresh disk for backups when I fell on the desk of the Geek squads and a nice employee begins to speak with me. I told her about my old computer and he said to go and I'll watch for free, if what ya got to lose?

  Jump on the Harley and was back in a Flash. It it turned on and started walking around talking with her friends, and I thought hmmm more of the same ol' Bull. He walked over and said are just as I thought. The hard drive is toast... yaaaaa toast... After a sale on what he could fix because I said could I do it myself. Know that he don't know if you know a little about them. I said that I am a quick learner for that kind of money. He gave me some tips and referred me to the hard drive section.

  Just finished loading the back ups ordered from hp vista more 88 updates (yawn) and... shes back in the saddle again... Thanks for your help... Any who need a mic DX7500. tour?

• Equium A60 will not start - get a beep code

  Hello

  This laptop has problems with ATI (even those included on the recovery disk) display drivers. He created a blue screen on a dll file.

  After reading around, I found that it was recommended to upgrade the bios, after going to the appropriate section of the Web site, I downloaded the flash tool from windows for the laptop bios.

  I ran and it opened, returned to the laptop and the screen is blank, a blue ring around the power button is on, but no display.

  I left it for a period of time see if it would to restart or something, but nothing has happened, it would not be the button turn off so I unplugged the power and removed the battery.

  To again turn on the laptop, it only stays on for about 3 seconds then turns off again.
  I get the beep code: short break, Long, short break, beep, beep beep, then it turns off.
  The caps lock and numlock keys are turned on.
  The DVD drive light blinks.

  But other than that, no display etc.
  Ive tried the battery leaving aside for awhile.

  Anyone have any ideas why flash bios toshiba own this would cause? Also what can I do about it? in any case to recover the bios etc via a recovery mode?

  Thanks in advance.

  PSA67E

  Hello

  Well, unfortunately for me it looks like a hardware failure.
  Maybe the motherboard is broken.
  These problems may occur if you use a bad BIOS or the incorrect BIOS update procedure.

  Please check this document FAQ How to upgrade the BIOS:
  IOS http://eu.Computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/FAQ.jsp?z=234&service=eu&from=faq_selection&CFID=B & FID = TRO0000000b07

  Unfortunately if there is something wrong with the hardware you should ask Toshiba service for assistance.

• P50/P70 BIOS beep codes

  Does anyone have the BIOS beep codes for the P50/P70 Thinkpads? Almost everytime I start mine beeps at me.

  3 short beeps, pause, 1 beep, pause, 1 beep, pause, 3 short beeps.

  I called tech support and they wanted me to uninstall the RAM I added after I got the system, or they want to send me the computer to replace the RAM and the system. I do not think that those who are the problem, however. After he gets a beep, it loads well every time. Lenovo solutions Centre zero errors with my system. No problem with processor, chipset and memory. Windows recognizes all 32GB of my RAM when it loads as well.

  Any ideas? I'm disinclined to send my system back because otherwise it usually seems to work OK.

  A 3-1-1-3 beep code heard at the start after change of memory reserved Thunderbolt from 1 GB to 2 GB in the Setup of the BIOS indicates a lack of PCI memory resources. After the beep, BIOS allows you to adjust the resource memory PCI allocated to love at first sight, then automatically restarts the system.

  Please note that Lenovo recommends running a 64-bit instead of 32-bit Windows operating system when you use the Thunderbolt of 2 GB of memory reserved parameter.

  In the setting of several screens or other devices to the Garland of Thunderbolt, Lenovo recommends the use of the resource of memory of 2 GB to the BIOS Setup and deal with the 3-1-1-3 model beep to restart the computer after changing the configuration of the BIOS as successful confirmation of change the BIOS POST.

  When you attach a monitor or a couple of other devices, Lenovo recommends the use of the resource of memory of 1 GB in BIOS Setup.

  Thank you

• Comouter to school does not start sometimes beep codes wirh.

  Probably not the right section *.

  I use a Lenovo Thinkcentre spare part in my class 1st period to recharge my phone. Sometimes he gives a short beep, or 5 short beeps and no video. Fan runs at full speed when he does this, and I don't know what is the model, but it has a sticker with MT - M and S/N codes. What is going on? Thank you! It works under XP.

  Click here:

  http://bit.LY/1sXsDMs

  Then, you can find the manual of Lenovo ThinkCentre and look at the section describing the sound and other codes troubleshooting information.  Other search results link to other places that might give you some clues.

  During the POST (Power On Self Test), beep codes usually indicate some kind of a hardware problem - as a loose connection, failing RAM or video subsystem, incorrect CMOS configuration, etc.

  On most systems, a short beep at startup is usually a good sign that the MESSAGE transmitted.  Several beeps (and sometimes no beep) are usually a sign that something is wrong.

• Compaq Presario SR2010NX beep code error starting: longbeeppausecontinuinglongbeepspausebetweeneach

  Hello.  My Compaq Presario Desktop PC SR2010NX of 2006 began just not start.  It gives me a sound code of long beeps that accompany pause after each beep and continue indefinitely.  I have tried convenience cheques, and it looks as if it was the 'memory '.  My question, FEI's memory, what cards are hardware compatible with my PC.  I had a breakdown.    to install a new set of 2 GB cards in July - and I had technicians immediately reinstall my old 2 cards (issued factory) replacement cards they have advised me to buy are not compatible, and when I went to pick up my computer, the computer would not start.  I have askede to reinstall my old cards and the computer booted suceesfully, and I left the store!  I am sure that I do not know what new products could be compatible with my old PC.  I thhink 4 GB is too myuch for my computer, and he couldn't get half that - but what brand should be like new hardwrae?  I wasn't expecting my old cards fail when they were resettled - three months since the change of memory attempt - thre months they started normally.  They have been re-hurriedly harnessed and dismissed the case, and then I left the store.  (The tech threatedned me with fear of "motherboard failure", which just made get the computer and leave immediately.  The old cards cannot have been relocated safely.  I'm taking it - but I will not be pushed around.  Of course - as old as mine PC would gradually motherboard failure.  Until it fails.  It was the memory card, but what woud cards my PC take that would be accepted as new hardware and allow my PC to boot up normally, if it is the cards and not yet the motherboard?

  I have now read the post with indicator on the upgrade memory.  It was very useful, and I wrote notes for the Presario.

  It says, maximusmis 2 GB to 1 GB cards/no stamped with the form of the data of motherboard page.

  It is divided between 2 cards 512 MB factory.  It has only 2 slots.

  Thank you.  My Compaq desktop computer has grown on me.  I got Vista bfore and I didn't know what I think.  If it can be repaired, I think 8 years (purchase date 4 November 2006) were fun for the low-end model.  It was a good choice, and I have never regretted buying at what cost.  It was better than expected.

  I haven't used my Compaq Presario continually over the past eight years - that's why it lasted so long!  Dud ut do work, however.  I had retirement is put online last year

  I liked HP Photosmart first 6.5 photo editing.  I liked Wordpad.  Mechanically, it was scientifically.  The material began to go when the built-in CD/DVD internal drive has failed.  I bought and had a replacement (DVD player (cd) internal HP) installed in July 2014.

  The new internal DVD writer HP compatible service pack XP? I have SP2) - I don't think it's about compatible new material.  This caused unable to start new businesses after three months?  New feature of device recognistion and old motherboard? Don't know?  (short circuit)?  I left the old CD/DVD recorder factory in its case - it's there and the springs are working to open and close the casing and check it / A short?  Don't know anything about electric

  Another point, when the original memory card 512 MB on factory 2 cards have been resettled, he was press-technicians to get the computer to boot - so the computer's case has been closed.   (I took the PC on their part awqay as fast it was closed upward).  I thought safe in maintaining clips?  Maybe not securely harnessed.  Could also be from the old factory of 512 memory cards in each clip spare wedge - to alternate which card and which support clip.  I have not tried this or re-cutting to the place of repair.  (I do not have any technical installation and not have ny contact danger here - I do not touch the computer).  It is the matter of repair - these people in a hurry, they sell - they tell you something will work, they overtest, they overdiagnose - they push you autour-yyou never recover your computer to use as is - it is disturbing to go, if you are not a consumer savvy or technical.

  May not be able to take new material old = change motherboard in chipsets, etcs. features.

  Ialso had an error saying years only. IPC Port would not work.  (. COMI is the base model for the CPA called Palm Zire Hotsync Manager.  I don't think the Palm Zire software uninstalled iI, and the message is a (!) origin unknown error message is:. COMI, has failed to initialize.  It's a pop-up error message appeared during the startup process.  The repair people off the message.  The boot has been at once - disconnect - the plugin twice and electric start.  It was based on the plug in the socket, removed and reconnected before the start =.  Technicians tried to solve this problem, but it is not important from my point of view.  All of those, cumulatively, could be symptoms of a hardware change progressive until the end of the use of PC - they are all could be chips card mother falling out or something there (the CD player, the.) Port COMI - don't know about the real, even if start program - which can only be that.)

  I tried the power reset function discussed in the Troubleshooting Online Web pages - 5 seconds to reset, / 15 seconds to reset - power off (unplugged) and hold the power button / stop without plug-in for 5 or 15 seconds (depends on the Web page of the online manual!)  Once, after an attempt to reset of fifteen seconds, the computer has no beep, and he almost made a second rumble noise - but then no change afterwards.  The redonnee start-up sound code beep after that the computer was turned off and then restarted again.

  PC is sitting in his corner.  I don't want someone break while I think about what to do.  He's going nowhere right now.

  This is the first time, it would not start.  I am a bit worried and disappointed, but, I know that my PC is old, and one day, it will fail to work.  That is the reality.  If it fi fixable, I'm interested to hear about the fit-it.  Thanks again.

  Hello @lliil,

  I read what you posted and it seems that you have a hardware problem with your computer. The only thing I can do for you is to provide you with the HP support document: BIOS Beep Codes, which will help you to correctly identify what's wrong with your computer. Given the age of the computer apart from this if you want to know if it can be fixed, I recommend do you get into a local computer repair shop and let them take a look.

  I hope I helped. Thanks for posting on the HP Forums. Have a great day!

• Beep codes IPMMB-FM

  I just bought a new computer:

  http://support.HP.com/us-en/document/c03649846

  Motherboard: IPMMB-FM

  video card: AMD Radeon HD 8470 1 GB of DDR3 memory

  When I got the computer I replaced the graphics card AMD with a nVidia GTX660 and also changed the power supply for an Antec 650 Watt because of the increased workload of the video card.  Then I reset the CMOS using the jumper and he gave me the beep codes (8 simple tones) that I did not understand. The computer comes with no manual indicating the beep codes, or I couldn't find any online.

  I went and then replacing the AMD Radeon HD 8470 and it works again.  So the question is:

  (1) where can I find beep codes for this motherboard?

  (2) in addition, it seems that he does not like his graphics card configuration to change?

  It seems I'm not the only one who experience this issue:

  http://forums.HardwareZone.com.SG/hardware-clinic-2/%5Bnoob-QNS%5d-PCs-GFX-upgradable-4142950.html

  Any idea would be appreciated. Thank you.

  PS: I used to build the computer with parts if this is new to me.

  Hello:

  What you are experiencing is new with W8 PC.

  You must go into the BIOS, turn on legacy mode and disable secure boot.

  See this document on the link below. If you have the video there is no need to remove your new card.

  http://support.HP.com/us-en/document/c03653200

• T60 will not boot receive the beep code 1-3-4-3 any suggestions on what this might be?

  Hi guys,.

  My T60, does not start all of a sudden. I can't access the BIOS. I received the following beep sequence: 1-3-4-3.

  I looked around and got as a message for phoenix BIOS beep code 'Test 512 K base memory '. Anyone has an explanation, and I should do or change?

  Thanks a lot for your support!

  Antoine

  I don't have one of them, but if it's a mistake of memory, the best way to test is to substitute known good memory. If you have two SODIMM modules installed, remove them and install one at the time and the test.

  Sometimes remove and reset of memory are sufficient to solve the problem.

  If this does not help, a good 'generic' method that I use on all laptops with a no boot situation is to remove all the drives and cards, then see if it will boot to the BIOS, or post at all. I've seen poor readers force a system not to post, so remove everything that is not required will be an easy way to identify the cause. Usually, if it will not always display, you'll have a system board failure.

• XPS 8300 beep Code: 3 beeps = Chipset error

  Hello

  My PC gives me 3 beeps when I try to start it. According to the manual, it means "the Possible - Chipset error system board failure." I don't know what this means or what to do about it.

  At the end of a Dell automated support center scan (I think that it is a scan and not an update) my computer froze and then the clocks reset to 0. I turned off the restarted it, but not in safe mode. I then decided to try to restart in safe mode. That's when I got the 3 beep code.

  Can anyone give me any help or advice on what to do about it?

  see you soon

  Justin

  Try to clear the BIOS:

  1. Switch off and disconnect
  2. Power button press / hold for about 15 seconds
  3. Open the case and remove the motherboard battery
  4. Power button press / hold for about 30 seconds
  5. Use canned air to blow out the dust bunnies
  6. Reinstall the battery (right-side-to the top!) *
  7. Close the case and see if it starts with the single monitor, keyboard and mouse connected

  * If the battery is no longer of ~ 2-3 years old, this could be a good time to install a new. Battery CR2032 lithium ion cell, ~US$2.00 in discount stores.

• XPS17 L702X 4 beep code when the 2nd module of RAM is installed

  Hello

  It started as a month ago, when I tried to boot my laptop but instead, I was getting this code 4 beep (RAM read/write failure). What I did then was remove/switching modules memory until I found one of them did not (the one on the DIMM A slot). So, I order the new RAM, install it and laptop works very well for about two weeks.

  Just today, I tried to start and got the 4 beep code again. Same old same old: remove a module, test, replace the module, test... but this time, whenever I fill the slot DIMM A laptop does not (4 beep code of course). Can I use any of my RAM sticks DIMM B and the computer works perfectly, which means that my memory sticks are bad.

  I would be grateful all the ideas,

  Thank you

  -Pablo

  FYI, I have 3 modules of 4 GB of RAM, 2 of them are the Corsair RAM I bought recently and the other came originally with the laptop (Hynix)

  Sounds like a memory wrong - turned support, you will need to replace the motherboard.

• HP Compaq D220 mobo POST, just beep codes...

  Well, it's really frusturating. I thought that I would have figured this out now. I turn on the motherboard, and I get 5 short beeps, a pause, then 5 more and so on...

  I tried Googling the model mobo (Lite-on NR138) and there is no record anywhere, I know it's old, but even the HP Compaq D220 page is void of any useful information. No specification page. And the 'upgrade and migration' page is a dead link.

  It would help me a lot to know what the beep codes mean, but it would be useful also to know if BIOS this motherboard only recognises
  some steppings, because I already tried 3 different processors. Two of them with B0 stepping and a C1 stepping.

  The first CPU I tried was SL68Q (1.8 Ghz, 512 K, 400 Mhz) there were 5 beeps.
  Then I tried SL6LC, with c1 stepping (2.0 Ghz, 128 K, 400 Mhz) it did not work at all, I don't even have the beep codes. (Not surprising, I think it's Fried).
  Finally, I tried SL66Q which is identical to the first (1.8 Ghz, 512 K, 400 Mhz) it has also resulted in 5 beeps.

  And Yes, I have excluded from the RAM, I tried 2 DIMM different (the two work in other systems). So I'm convinced it's a CPU problem.
  Any comments would be appreciated, especially if you have this mobo and have updated the CPU.

  ERICO, thanks for the suggestions.

  Problem solved!

  The RAM card was loose on one end, and after pressing it with all my strength, click on it. I was sure that it was not the RAM, because I had tried several cards, different slot machines even (but they never wanted to click). In this particular mobo slots are all that I've seen the difference. The grooves are short, so the modules look like they are sitting on the top of the Golden Groove contacts. It takes a lot of strength to their seat correctly.

  That this should be a lesson for me and others, that it is always a good idea to triple- check each strip memory and be very sure that they are not stirring, or tilted. The tabs on each side must click by themselves.

  The Council is an American Megatrends Inc. Model [FRIEND] NR-138. (No Fujitsu, or Lite-On). It is brand HP, but has an AMI BIOS, not Phoenix / Award. It recognizes the processors that I tested previously. He took AGP, Audio and LAN. The chipset is Intel 845GV.

  So in summary, five 5 short beeps of this Council is equal to "RAM not detected."

• Beep code for notebook (g6-1d48dx)

  Hello world

  I just had a problem with my laptop, it does not start and beeps with 3 long and 2 short, and then led the caps are flashing until I have disable (without rhythm or code, the last time that I counted 23 flashes until I have turn it off), so I tried to find a beep code this game with him, but I don't have anything also I can't find the manufacturer of the bios. All know what this could mean?

  Oh well, thanks for those who read and help!

  Hello

  Please consult the following for this work first:

  Beep codes for HP laptops

  Kind regards