Compaq Presario SR2010NX beep code error starting: longbeeppausecontinuinglongbeepspausebetweeneach

Hello.  My Compaq Presario Desktop PC SR2010NX of 2006 began just not start.  It gives me a sound code of long beeps that accompany pause after each beep and continue indefinitely.  I have tried convenience cheques, and it looks as if it was the 'memory '.  My question, FEI's memory, what cards are hardware compatible with my PC.  I had a breakdown.    to install a new set of 2 GB cards in July - and I had technicians immediately reinstall my old 2 cards (issued factory) replacement cards they have advised me to buy are not compatible, and when I went to pick up my computer, the computer would not start.  I have askede to reinstall my old cards and the computer booted suceesfully, and I left the store!  I am sure that I do not know what new products could be compatible with my old PC.  I thhink 4 GB is too myuch for my computer, and he couldn't get half that - but what brand should be like new hardwrae?  I wasn't expecting my old cards fail when they were resettled - three months since the change of memory attempt - thre months they started normally.  They have been re-hurriedly harnessed and dismissed the case, and then I left the store.  (The tech threatedned me with fear of "motherboard failure", which just made get the computer and leave immediately.  The old cards cannot have been relocated safely.  I'm taking it - but I will not be pushed around.  Of course - as old as mine PC would gradually motherboard failure.  Until it fails.  It was the memory card, but what woud cards my PC take that would be accepted as new hardware and allow my PC to boot up normally, if it is the cards and not yet the motherboard?

I have now read the post with indicator on the upgrade memory.  It was very useful, and I wrote notes for the Presario.

It says, maximusmis 2 GB to 1 GB cards/no stamped with the form of the data of motherboard page.

It is divided between 2 cards 512 MB factory.  It has only 2 slots.

Thank you.  My Compaq desktop computer has grown on me.  I got Vista bfore and I didn't know what I think.  If it can be repaired, I think 8 years (purchase date 4 November 2006) were fun for the low-end model.  It was a good choice, and I have never regretted buying at what cost.  It was better than expected.

I haven't used my Compaq Presario continually over the past eight years - that's why it lasted so long!  Dud ut do work, however.  I had retirement is put online last year

I liked HP Photosmart first 6.5 photo editing.  I liked Wordpad.  Mechanically, it was scientifically.  The material began to go when the built-in CD/DVD internal drive has failed.  I bought and had a replacement (DVD player (cd) internal HP) installed in July 2014.

The new internal DVD writer HP compatible service pack XP? I have SP2) - I don't think it's about compatible new material.  This caused unable to start new businesses after three months?  New feature of device recognistion and old motherboard? Don't know?  (short circuit)?  I left the old CD/DVD recorder factory in its case - it's there and the springs are working to open and close the casing and check it / A short?  Don't know anything about electric

Another point, when the original memory card 512 MB on factory 2 cards have been resettled, he was press-technicians to get the computer to boot - so the computer's case has been closed.   (I took the PC on their part awqay as fast it was closed upward).  I thought safe in maintaining clips?  Maybe not securely harnessed.  Could also be from the old factory of 512 memory cards in each clip spare wedge - to alternate which card and which support clip.  I have not tried this or re-cutting to the place of repair.  (I do not have any technical installation and not have ny contact danger here - I do not touch the computer).  It is the matter of repair - these people in a hurry, they sell - they tell you something will work, they overtest, they overdiagnose - they push you autour-yyou never recover your computer to use as is - it is disturbing to go, if you are not a consumer savvy or technical.

May not be able to take new material old = change motherboard in chipsets, etcs. features.

Ialso had an error saying years only. IPC Port would not work.  (. COMI is the base model for the CPA called Palm Zire Hotsync Manager.  I don't think the Palm Zire software uninstalled iI, and the message is a (!) origin unknown error message is:. COMI, has failed to initialize.  It's a pop-up error message appeared during the startup process.  The repair people off the message.  The boot has been at once - disconnect - the plugin twice and electric start.  It was based on the plug in the socket, removed and reconnected before the start =.  Technicians tried to solve this problem, but it is not important from my point of view.  All of those, cumulatively, could be symptoms of a hardware change progressive until the end of the use of PC - they are all could be chips card mother falling out or something there (the CD player, the.) Port COMI - don't know about the real, even if start program - which can only be that.)

I tried the power reset function discussed in the Troubleshooting Online Web pages - 5 seconds to reset, / 15 seconds to reset - power off (unplugged) and hold the power button / stop without plug-in for 5 or 15 seconds (depends on the Web page of the online manual!)  Once, after an attempt to reset of fifteen seconds, the computer has no beep, and he almost made a second rumble noise - but then no change afterwards.  The redonnee start-up sound code beep after that the computer was turned off and then restarted again.

PC is sitting in his corner.  I don't want someone break while I think about what to do.  He's going nowhere right now.

This is the first time, it would not start.  I am a bit worried and disappointed, but, I know that my PC is old, and one day, it will fail to work.  That is the reality.  If it fi fixable, I'm interested to hear about the fit-it.  Thanks again.

Hello @lliil,

I read what you posted and it seems that you have a hardware problem with your computer. The only thing I can do for you is to provide you with the HP support document: BIOS Beep Codes, which will help you to correctly identify what's wrong with your computer. Given the age of the computer apart from this if you want to know if it can be fixed, I recommend do you get into a local computer repair shop and let them take a look.

I hope I helped. Thanks for posting on the HP Forums. Have a great day!

Tags: HP Desktops

Similar Questions

  • Desktop Compaq Presario has beep and won't start

    My Compaq Presario desktop PC makes a sound beep and won't start. The SN # is CNX65112RS. Someone help me please!

    That's great. Please mark the thread as solved.

  • Compaq presario co50-210us - fail to start

    We have a laptop Compaq Presario CO50-210US, yesterday, the screen started to decrease in intensity, and access to programming or internet became slow. Finally, the screen went black and the computer turns off.  Since then, any attempt to power on the results of the computer in the 3 in the FRONT lights flashing 3 times and then nothing.  Power supply is correctly attached and plugged and a hard reset didn't help, and I don't see any other options.  I recently used can air and blew out the dust of all openings, I could find including remove the panels for access to the disk modules and hard memory. This computer has a history of heat so much that he stopped in the past, and re - start not only cooled, (half an hour or more), even though he is sitting on a cooling block at any time.

    Any suggestions on what to do next? And what does the blink code mean?  Any help will be welcome.

    Solution:

    Apparently, the three flashing lights mean 'wall charger is DEAD, and the battery is empty.  Bought and plugged a new charger and the computer works as before.

    Hello jboone,

    Welcome to the HP Forums!

    With your computer starts does not, this can result from several separate components. I've included the document 'computer won't start (Windows 7, Vista, XP)'. Please follow the General troubleshooting steps and then click on the symptom that best describes your problem, follow the steps.

    Please let me know if you are able to get your computer to boot correctly, or not.

    Thank you.

  • Looking for a recovery CD for Compaq Presario V3136TU? Technical error: NTLDR is missing

    I formatted my Compaq Presario V3136TU 2 days ago and has discovered just when I run the 2nd recovery CD, there is an error message that some files cannot be read. After completion, my laptop won't boot any more completely.

    NTLDR is missing
    Press Ctrl + Alt + Delete to restart.

    I have tried a few attempts.

    1 browser through all the HP site and emails of support no answer me have so far so I give up on their e-mail.

    2 find the Web site to install depending on the operating system, but when I try to install Windows XP, it says hard drive cannot be detected.

    http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?product=3289312&lc=en&cc=us&dlc=en&lang=en&cc=us...»

    If anyone has an idea about this, please advise.

    3. then I find a site that allows you to download.
    http://www.user-guides.co.UK/cddownload/HP/HPCompaq/HP-Compaq-Presario-V3000Z-Ntldr-Boot-CD-disk-98-...

    Have someone tried this site, I'm abit worried if it's reliable?

    4. I called the technical service of HP, and technical personnel will only direct me to call the hotline (1800-272-5333) and to order the recovery CD, the price is SGD $50.00, more min 3 days and car collection.

    I'm really very sad with the HP service.

    If anyone have a Compaq Presario V3136TU, PM me please.

    Thank you very much

    If the above mentioned fixmbr is not work_You may need to remove this extra partition. Boot with the XP cd and go through a fresh install, delete both partitions and let XP to create a new installation to.

  • Compaq Presario turns on but not start

    Product: HP Compaq Presario
    Model: SR5250NX
    OS: Windows Vista

    Symptoms: When you press the power button, all the lights come on as expected. However, a slight popping noise that sounds as if it is coming from the hard drive will ensue. The monitor, mouse and keyboard are not recognized despite being plugged in, even if the speakers are always lit. It is a problem, I am back after a journey of four days out of town, and I heard the internal fans speed up just from time to time for months. I guess this thing is fried, but I hope it can be fixed. Thank you.

    This

    http://support.HP.com/us-en/document/c01443366

    says 1 blink = bad processor. Sorry Charlie, I'd scrap it.

  • dv2055 ea starts - beep code errors

    Hi all

    I am writing to the following problem (and I'm desperate enough):

    I have this laptop, which, in the last days sometimes not been started, giving rather beep errors. Today, it just does not start.

    Now, the weird thing is that it gives a long beep and two short, while checking here I found only the references to (I assume) number of beeps.

    So, I just spread this oddity and removed benches from memory and tried everything (Bank 1 in slot 1 and then slot 2; Bank 2 slot 1 and then into the slot 2: I've upgraded memory, but I did a year ago), but I've only got a change in the number of beeps: they became 4, shorter, and it seemed that they were from the internal PC speaker and not from the speaker "big media" (made I can try using headphones and check this box)

    Worst thing is that I am now studying abroad: I can't send (I guess) my laptop using, and I must keep my HD.

    So, no idea what's going on / what I need to do?
    Thank you very much

    You have a GPU issue.

    Assuming that you are out of warranty and the desire for the workbook as soon as posible, I advise you to go to the component repair shop nearest.

    The connection between the GPU chip and the motherboard must be reorganized.

    If you have any EE skils you can repair yourseft, google for redesign or motherboard, you will find useful information.

  • oxc0000135 code error starting of google chrome on windows vista

    I rebooted google chrome and when I try to open it I get the error code oxc0000135, application failed to initialize properly.  y at - it a patch or a cure?  This all started after installing fios at home.

    Hi Loubishop,

    Are you facing issue with Google chrome or another application also?

    If you are facing the issue only with Google chrome, you might get in touch with Google for additional assistance.

    Support Google

    http://support.Google.com/chrome/bin/static.py?hl=en&topic=14684&page=table.cs&tab=21605

    You can also visit our Google support at the address below.

    Impossible to open and launch Google Chrome. Error Application failed to initialize properly (0xc0000135). End it.

    The above mentioned thread contains third party links.

    Note:   software use of third parties, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third-party software can be solved. Software using third party is at your own risk.

  • Compaq Presario CQ62-412NR does not start. Caps lock flashes.

    The LED caps lock flashes repidadly with long breaks between each blink, the wireless light and constant and the adapter LED is steady. I read blink codes and determined, he was the processor, but the problem persists after him substituting a known good. I finished the resets power to clear the bios before and after the change of the CPU. I also tried to replace the RAM. Anyone here have a clue whats going on?

    This looks like a problem with the motherboard if you already replaced the CPU and RAM.

    It would be probably cheaper to replace the unit at this time only so, fix it or replace the motherboard.

  • clear my bios administrator password for compaq presario CQ62 (my code 63859453

    pleaase help (my code 63859453)

    Hello

    Please try:

    72731495

    Kind regards.

  • I have a Compaq presario sr201nx.

    What is the maxium size hard drive I can put in a compaq presario sr2010nx under windows xp?

    He currently has a 120 GB hard drive in it.

    ksbear57 wrote: I also put a 400 GB sata and when I was burning a dvd in some way it crashed the 400Go.

    Hello ksbear57, the 400 GB hard drive you have installed in your system was bought as a hard drive on the retail, you should have at least a three-year factory warranty.

    If you still have the hard drive, you can visit the web site of the manufacturer of the hard drive. Enter the serial number and see if it is still under warranty.

    I don't know the DVD burning was the cause of the crash of the hard drive. It may just have decided to expire on it's on.

  • Compaq Presario upgrade

    Can I upgrade my Compaq Presario SR2010NX from Windows XP to Windows 7? Currently has 512 MB of memory.

    Hello:

    Your PC should be able to run W7 but W7 32-bit requires a minimum of 1 GB of system memory.

    Also run windows 7 upgrade advisor and see what it reports.

    http://www.Microsoft.com/en-US/Download/details.aspx?ID=20

  • Compaq presario cq61 Fez at startup

    Hi there my compaq presario cq61 freezes whenever I start it. I pass the boot compaq logo then I get a black screen frozen with a white blinking underscore in the top left corner and the wifi button is constantly lit orange. I can press the esc key when Startup logo is in place and a lot of options appears, but I don't know what to do. Thanks in advance. Greig.

    Hello

    If you do not, use another PC to create a Windows 7 recovery CD.  Download the ISO from the link below.

    Windows 7 32 bit

    You must use an app like ImgBurn to burn the ISO to a CD - a guide on the use of ImgBurn to write an ISO on a disc is here.

    Start your laptop from the rescue CD, you have created, select repair your computer and choose the command line.  When this charge, enter the following commands and press on enter after everyone – including spaces as shown.

    Bootrec.exe

    bcdedit/export C:\BCD_Backup

    c:

    Boot CD

    BCD attrib s h - r

    Ren c:\boot\bcd BCD.old

    Bootrec /RebuildBcd

    Bootrec /fixmbr

    Bootrec /fixboot

    Remove the rescue CD and try to restart now.

    Kind regards

    DP - K

  • I have a compaq presario cq60 with vista which was able to start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. What can I do?

    I have a compaq presario cq60 with vista. Could not start after the installation of windows updates. HP recovery failed with error code 100a and bios self-test gave error fail #1-07. I took the hard drive and installed in my office. Windows Explorer displays the main and recovery partitions.

    The primary partition has the following folders (including hidden & system)

    The recovery partition has the following (including the language files more)

    Someone at - it ideas why my laptop does not work?

    Thank you

    Greg

    Hello

    You press F11 on startup with a HP Compaq to start the recovery process.

    For problems with the recovery process, you will need to contact HP.

    BIOS problems:

    There are messages for the HP Forums for posters with similar errors:

    http://h30499.www3.HP.com/T5/notebook-HP-ProBook-EliteBook/notebook-HDD-problems-TEst-status-1-07-fail/TD-p/658902

    http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-dv8000-getting-1-07-fail-error/TD-p/883284

    http://h30499.www3.HP.com/T5/notebook-PCs-pavilions-Presario/HP-Pavilion-notebook-dv6000-1-07-fail/TD-p/1069457

    All the answers it point to a drive about to fail

    See you soon.

  • "Beep code" Compaq Presario SR5510F POST

    My Compaq Presario SR5510F fails his POST and gives 1 short and 1 long beep, repeatedly. What does this code mean? I can't find this code on any list of beep codes, that I managed to locate.

    Blessings,

    Father of Dal

    FatherDal wrote: Dear Hanspuppa, thank you very much for your help.  Actions suggested by your response seems to have solved my problem.

    Hello FatherDal, it's really good news. If you have determined that your system has at least one memory defective Strip, and you want to replace the defective module, you can consider replacing all the memory modules and purchase of some additional memory that can increase the performance of your system.

    Here is the link to the specifications for your system. It shows that your system shipped with 2 GB of memory system.

    It also shows the system supports up to 4 GB of memory system and your system shipped with Vista x 86 (32 bit).

    All 32-bit operating systems can only recognize up to 3.25 GB to 3.5 GB of memory. The x 64 bit version can recognize 4 GBs whole memory system.

    I would say that the upgrade of your system memory to 4 GB into 4 X 1 GB modules. Even if your current operating system would recognize the 4 GBs set of system memory, you should see a performance increase with additional memory.

    Here is the memory critical link where you can buy compatible memory for your Compaq system.

  • How to start a Compaq Presario that will beep at me?

    I have a Compaq Presario desktop computer that I "inherited" a close two weeks ago. It has worked fine until this morning. After installation of new RAM sticks and get black screen ("We apologize for the inconvenience... ") twice, rechecked everything carefully and then get a blue screen telling me that"ati2dvag.dll"was responsible for the shutting down Windows, etc, it starts today!

    The fans start, so be able to do... but it comes is and keeps me beeper!

    It's a SR1619UK, running XP SP2 & Radeon Xpress 200 graphics chipset... and a 1 GB of RAM.

    Someone tell me what is happening?

    Life is what you make...
    *****************************
    You can only be sure of three things in life; birth, death, and taxes; Hah!

    Greetings, Dokie and Geekster.

    Sort problem! Given that I don't seem to be getting anywhere, I resorted to the suggestion of a friend of re-Foundation original RAM sticks (pair of 512s), and... It worked! (I told you I was new to this, and that I had not worked on your desktop before...)

    I must have disturbed them when I first tried installing the 1 GB module who came the other day. I never thought it possible... they are a VERY tight fit in these slots, and they need a little bit of pressure to engage the locks. but this is what must have happened.

    I'm willing to believe ANYTHING can happen with these gadgets now... !

    Thanks to the pair of you for your help with this... and it was more enjoyable to chat with you two. I know where to go for assistance in the future.

    Mike

Maybe you are looking for

  • Changing default text when sharing music via Twitter

    I was wondering if there is any way I can change the default text, iTunes uses when I share my music via Twitter. The default text is "Listen to [TITLE] of [NAME of ARTIST] on @AppleMusic", and I want to update the text of ' #NowPlaying [TITLE] of [N

  • Screen is not the only band of the screen.

    HelloA bunch of compact my z3 Xperia screen does not work. Or at least that it does not touch. Is that what I can do about it? The screen is not cracked or anything like it either just does not respond within this particular band of 1 cm long and hor

  • Windows 7 Embedded - stop does not exist

    The shutdown.exe command is not present in the Windows system32 folder. How can I stop or restart a windows 7 embedded system via command line? Thank you

  • Slooowly impression

    While trying to print any type of document (excel, word, etc) on my printer HP 5650, it prints extremely slowly, and the printer wait state is "error-printing".  I troubleshoot-performed the printer with no result.  Is there a setting that may explai

  • BlackBerry Z30 dOWNGRADE TO z10 z30

    I HAVE a z30 AND LOVE it. I had to send it FIR a repair. I have a Z10 as a loan. I can put the Z30 save the file on the Z10. I get errors? Thank you Skybuckets