Temperature of the E3000 router...

Similar Questions

• E3000 won't handshake with the edge router

  Recently, I bought new E3000. I place the E3000 with edge router static IP address rather DCHP which seemed failing at the same IP address and DNS. Associated with the E3000 laptops have their own IP which differ from the IP address of the border router. E3000 is configured with firewall No. minimum protection, for now. The reason for a minimum protection was to get the handshake between the two routers. The border router is a product of Verizon. The old router I was using is a Netgear who did the handshake with the edge router. I have the latest firmware for the E3000 version of the Firmware: 1.0.04)is build 6. Router will not handshake with wired connections or wireless. Used to connect to the E3000 laptop is running Windows 7 Ultimate.  In fact, all laptops here use the same OS and connect wirelessly. I've tried the package of software provided on the site, which housed a diagnosis that apparently could not solve the problem as well. I have not idea about why E3000 not handshake with the edge router. Can we make a few suggestions. Thank you to all those who respond.

  What is the IP address of the router Verizon? What you write suggests that the Verizon router uses 192.168.1.1. If this is the case, establish the E3000 as a switch simple ethernet access point as follows:

  1. disconnect the E3000 from the Verizon router.
  2 wire a single computer in the E3000.
  3. open the web interface at http://192.168.1.1/ (or whatever the IP address you put it now).
  4. on the main configuration page, make sure that your type of internet connection is on "auto/DHCP.
  5. on the same page, set the LAN IP address to 192.168.1.2.
  6. on the same page, disable the DHCP server.
  7. save the settings.
  8 unplug the computer and one of the LAN ports numbered from the E3000 wireless to your router to Verizon.

  That's all. Now, you can use the E3000 as access point and you can use the remaining 3 LAN ports for wired devices.

• No info from internet provider to my E3000 router from a bridged walkway to Arris T268G

  I am a customer of Comcast and had my gateway Arris T268G filled so that I could use my E3000 router for a wireless/wired network. My configuration is: on the bridge in bridge at the entrance to the internet of my E3000 then the cable coming out at my SE2500 Ethernet switch which I then cable to my PC to the cable connection. No internet. My wireless router is broadcasting because I'm picking up signal but no internet connection. Looking at the dashboard of the E3000 'Status' tab there is no information for the internet provider. I hit the button refresh and renew the IP button and still nothing.

  (1) is my correct configuration?

  (2) is there a setting I should change to communicate correctly with the T268G gateway (defined in bridged mode)?

  Peyates, it is possible that the IP address of the modem and the router's IP address are both in the same IP range. Change the IP address of the E3000 to, say, 10.10.10.1 before you connect it to the modem. In addition, if the DHCP server on the own modem is enabled, you can configure the E3000 and cascade via LAN to LAN to the modem.

  See this article.

  http://Linksys.custhelp.com/cgi-bin/Linksys.cfg/php/enduser/std_adp.php?p_faqid=3733

• Share USB over the internet using the E3000

  I just bought an E3000 router, everything started installation and configuration USB share for my network. But how to share this USB on the Internet with the family etc. ??? I keep searching and searching and just can't find the answer. It's the ONLY reason I bought this specific model.

  You are able to share the drive within the network?

  Open the router configuration page and go to storage tab, click Activate the FTP server FTP server void tab and enable access to the Internet.

  Now, go to the status tab and check the IP address of the Internet on the status page. Note the Internet IP address. Consider the Internet IP address X.X.X.X. . Open the Internet browser and in the address bar, type ftp://X.X.X.X .

• The E3000 does support 5 GHz channels > = 149 or only 36-48?

  Hi, I have read various messages of the forum saying best performance of a wifi router, you must use the channel 149 or MORE and only 36-48 have a lower signal strength and therefore less range and speed.

  I live in New Zealand and when I select the drop-down list for the 5 GHz band wireless channel he mentions only 5 options - Auto (dfs), 36, 40, 44 and 48. I read the posts of the forum of people saying you should switch to 149 or more and I saw some screenshots showing the drop-down list with 149 selected. But I did not have this option.

  If I check status > Wireless page, it shows that the channel 36 is used (for automotive).

  I'm doing something wrong? E3000 in this part of the world do not support 149 etc.?

  I spoke in a live chat with a support representative who told me that all the E3000 are the same everywhere in the world and there was little or no difference between them in the firmware. I was also told that 36-48 strings are high gain and so there is no need for other channels, which contradicts the other articles I've read what 36-48 state are weaker channels.

  Can anyone shed light on this sone?

  Thank you.

  It is forbidden to put an access point wireless statically on a higher channel. All channels except the four listed should be used with DFS.

  See http://homecommunity.cisco.com/t5/Wireless-Routers/E4200-5ghz-channels/m-p/393155

• IP ISP lease time does not count on E3000 router

  Hi all...

  I just installed an E3000 router and have updated the firmware on the support site. I noticed that when I look at the router status page, the term of the lease IP ISP seems to be stuck and does not count down. When I reboot the router time will change, but it does not change as it should without a restart or a Relase and survivor.

  I am connected to the service of Time Warner Road Runner as my ISP...

  Does anyone else have this problem?

  Is this a known issue?

  Routers Linksys tells you only when the term of the lease ends.

• Replacement of the WRT54G Router

  I have a router that my cable company feel needs replacing. I don't really know if it's true, because they tried to sell me a new router or rent one for me. In any case I guess that replacement is necessary. I'm not a geek and my existing WRT54G Router was installed by someone else who went through all the work to set up my network home. Ideally, I would buy the same model router and use existing lines to connect the new router, thus reducing to a minimum the installation time and trouble. Of all the posts on this site, I am sure that installing a new router is not easy to do and is subject to many 'traps '. People spend days, installation of a router and a good number of them fail. It seems incredible to me that a manufacturer could produce a product that causes so much wasted time of clients and anguish.

  I am running Win XP ver. 3 with IE version 7. I'd like some experienced advice on which model of router would be ideal as a replacement for my WRT54G that was enough for my home network. So I would advice on the question of whether I should try to do it myself or hire a geek to do to me. I have next to zero patience and no tolerance for poorly written instructions. For those who have traveled down the road, I'm ready to go, tell him from me right.

  Router WRT54G is one of the best routers.

  Choose the router from Linksys E series (model E1000, E2000 and E3000). These routers are very easy to install. The speed and intensity of the signal will be very good compared to the WRT54G Router.

  You need not hire a technician to install the router. You will get a Cisco software connect with this router. Just run the CD and Cisco connect software will do everything for you. It will protect the wireless automatically for you.

• Use the second router to extend the network to Time Capsule

  I have a v7.6.7 running Time Capsule 1 TB and older airport. I'm hoping to add a second router in a new location, and I use an ethernet cable from the TC at the new router (TP Link Archer C5), updated to the latest version of the firmware. The IP address of the TC is 192.168.1.1.

  I have set up my router C5 as follows: allocation of IP 192.168.1.199, value DHCP = off, and I connect a cable between the TC ports and port WAN (not Internet) available on the C5. In the C5 wireless settings, I tried both using the TC SSID and pw and creating a new SSID and pw. In both cases, the network will work for a short time, but eventually the entire network, including the TC, stops working. I made no changes to the parameters of the TC on any trial.

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router? If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Is it possible to use a TC and a router not Apple on the same network? If so, what are the right settings for the TC and the secondary router?

  Yes. That would be the basis of a network of mobile type.

  The key for a roaming network parameters are:

  • The 'primary' router must be configured as a router. In other words, it must have active NAT and DHCP services.
  • All other routers used in a network of roaming must be reconfigured as a bridge.
  • All routers must broadcast a Wi - Fi network that uses the same network (SSID, aka) name, and the type of wireless security, and the password.
  • All routers must be interconnected by Ethernet. To provide Powerline adapters using an Ethernet connectivity should also work.

  If not, is it better to have the not Apple as main router and add the TC to the network created by the non-Apple router?

  Should not really which is the main in the roaming network.

  I think at this point, your current circuit line. To check that, I would suggest that you consider to bring back the router C5 in the same room as you have the TC. Then connect it directly to one of the LAN of the TC ports. Complete the entire upward to a mobile network and test it. If everything works, bring back the C5 in the desired location, and then try again.

  If it fails, then the circuit line will be tested to check that it provides a solid 'Ethernet' connection between the adapters.

• Ink advantage 2545: changed the name of the wireless router and now ink advantage 2545 does not connect and I'm out of ideas

  I have a Toshiba laptop 64 bit running Windows 10 Home, 8 GB, 1 t hard drive.

  Router is a Samsung phone using Android because it was the only router that I could find which would take the wireless signal.

  I live very pastoral, no neighbours for miles, so I never saw the need for a password on my router.

  Now, some people are installs in less than 400 feet from me, and I think they're piggybacking on my Wifi because my access speed has slowed considerably since they moved in.

  So I decided to change the password of the router, unfortunately, I can not put in any password I want.  It gives me the opportunity to have a predefined password.  So I changed the name of the router I could do without problem.

  My computer very quickly without any problem, however, my printer which worked great for a year with the old router name does not connect on the new name of the router.

  Here is what I tried:

  I had hoped he would ask me for a new name / password, but it did not.

  Then I plugged a cable between the printer and the laptop in the hopes that it would produce a different kind of results.  It has not changed anything.  There is no screen menu on what that be like this on the printer.

  I pressed the wireless button that has the flashing blue light and nothing happened.

  I pressed the button, don't know what it is, but it has a white light, and nothing happened.

  I went on the HP site and followed the instructions but he just said do not connect the cable until told to do so.  So I disconnected everything, lights out and turned back on and still no connection and no invite to plug whatever it is.

  Y at - it everywhere where I have being a novice could get instructions on how to get this working?

  I appreciate any help you can give me.  Thank you.

  Hello

  I think you are talking about SSID. Please, think of it as a new router and use the following ways to correct:

  http://www.HP.com/global/au/en/wireless/reconfiguring-system-Help3.html
  
  Kind regards.

• Satellite A200-1TP - the high temperature of the processor

  Hello, I have never had a problem with my laptop up to now... I was playing a game when I couldn't play more because my keyboard was raging on the left side.
  I checked the temperature of the cpu and it was 80 c! I don't know too much about temperatures, but I think it is too high.
  I closed the game and he lowered to ~ 60, then I tried a program called orthos to check the performance of the PC while making 400 iterations of lucas-lehmer and it reached 95 C! OK, it's time to do something.
  I tried to format my laptop and see what happpens... On 'high performance', it of about 64 c and on 'power saver' must be between 50 - 55 c, a better way but I think it should be lower. I tried to clean the fan with a vacuum and I think it helped a little... I dare not open my phone because I don't know that I'll break it.
  The fan is not broken, it is running, I tried using 'speedfan' change rpm, but this program does not detect my fan so I can't do anything...
  I don't know why this is happening. I was so happy until now... I would like to repair the laptop, not to buy a laptop cooler, then... what I need to do?

  Thank you

  -Furthermore, the disc is 41 c and GPU temperature is 27 c, I think these are ok.

  Hello

  > I tried to format my laptop and see what happens... On 'high performance', it of about 64 c and on 'power saver' must be between 50 - 55 c, a better way but I think it should be lower.

  No contact, the temperature will not stay if you run applications of high performance as the games for example.
  Running high-performance programs all internal devices must run with max performance which leads to a higher heat dissipation and this leads to a higher temperature

  Of course clean dust cooling modules and debris should help cool the laptop better but it won't change the fact that you will always see a higher temperature, running games

  PS: CPU keeps the temperature of 100 degrees, that's what I found on the Intel page!

• Extend the DSL router?

  I just got internet frontier DSL, and it comes with a wireless router & modem Netgear 7550. I would use my Airport Extreme to extend the reach of wifi at the front of my house and also plug my Airport Express to print wireless, and play music. How can I do this? I don't know anything about networks. Thank you!

  Ask Frontier to replace your modem/router with just a modem, so you can use your own router. Or, if the device has an Ethernet port for the computer, and then connect an Ethernet cable between the port of the modem/router and the port of world on the AEBS. Jam the device border so that the wireless radio is turned off. You should be able to extend the AEBS wireless using your AEX to print and play music.

  Network Apple devices do not extend the networks of non-Apple routers unless you run Ethernet cables for Apple devices installed remotely.

• Satellite M70-164: what is a default temperature of the HARD drive?

  I wonder if someone can tell me what are the default temperatures of the hard drieve of a satellite M70-164

  Hello

  It is not easy to say. It is based on the use of the HARD drive.
  If the turns HARD disk and OS write or read on/from the HARD drive, so the temperature increases, but if you use the laptop only for internet, so the temperature of the HARD drive remains on the low level.

• Satellite 1800-814: how to measure the temperature of the processor?

  I replaced the radiator component on my laptop as it freezes suddenly during the operation. Now everything seems to be better, but still a last question. How to measure the temperature of the processor?

  Dominic displays only HDD temp and MBM profile for 1800-224 display cases and the cpu. But if I can use this profile? Any other ideas how to meausre CPU temp?

  MBM shows me around 40 to 49 ° C for the cpu. Is this normal or too high just to run windows?

  Thanks in advance

  Greetings
  Jens Grieger

  Hello

  See this http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=5564&messageID=19417

  Maybe the help!

• OfficeJet 6600 e-all-in-one: Wireless connectivity with the new router problem

  We had the printer since 12 months, workin with no problems.

  Just got a new modem/router (NETGEAR V7610) installed as part of the NBN implementation and I can't get the printer to connect to the new router. 5 and 2.4 G active networks. The two defined newtorks on security WPA2-PSK [AES].

  The printer detects the wireless (2. 4 g) network, but can't coplete the connection. Tried the two direct input the network key and using WMA.

  -The display panel shows "wireless invalid password (WPA) is entered.

  -The results of network printer test page indicates a FAILURE on safety.

  I was able to connect to multiple other devices (laptop, iphone, Kindle...) without any problem. Used the two direct entry of the key network and WMA.

  Anything else I can try?

  Find a new update of the firmware for the printer (May 9, 2016).

  After you apply the update, the printer is able to connect to the new modem.

• Temperature of the system at 90 c in Portege R700

  When I turn on my Portege R700 and immediately open the Toshiba PC health program (monitoring sensors) it shows the temperature of CPU either very low, of course, while the temperature of the system is already at 90 C.

  As a result (I think but I could be wrong) the fan runs at almost maximum speed.
  The situation does not change in time: rest CPU temperature generally less 40 c, the temperature of system at 90 c, fan still spinning fast.

  Is this normal? The cooling test program says everything is fine.

  Daniele

  You should try to perform a cleanup of laptop:

  http://forums.computers.Toshiba-Europe.com/forums/Ann.jspa?annID=40

  > Toshiba PC (sensors monitoring) health program it shows the very low CPU temperature

  Hmm... If it shows that the temperature is low, but it goes up to 90 C, means do not work properly. Reinstall it, but before complete cooling system cleaning