The address of the Port of my LaserJet5Simx.

Similar Questions

• Problem with security of the ports and disabled learning MAC addresses?

  Hello

  Is there a problem, or incompatibility, if you configure the port-security on "n" ports that belong to X vlan and also disable mac-address-table of learning on this vlan?

  Someone did he do reference, links or PDFs on this problem?

  Thank you very much

  Best regards.

  Hi Javier,

  As I showed above, the combination is valid. I did not all static entries in the security of the ports, but all entries learned through port security will be shown as static on the show see the mac address table. All dynamic learning is disabled.

  I don't know what kind of security problem, that you try to resolve, but the configuration is valid.

  Daniel Dib
  CCIE #37149

  Please evaluate the useful messages.

• Portege R500 - configure the parser on the Port Replicator

  The system is Portege R500 with a port replicator Port MS Vista running. Port replicator has a Philips 19 "LCD monitor

  System has BEEN configured so that when the system was in the duplicator monitor 19 "inches would be active and system monitor is inactive.

  But, a few days before the following events occur, when the system is in the port replicator and its turned on screen (the one with the mobile progress indicator) Windows startup is displayed on the Port Replicator monitor, then the screen turns white and displays them on the screen on the monitor system, after entering the desktop on the monitor system.

  I live in a remote area, so I can't pop in the store of the local computer to ask for help.

  I would appreciate someone to give me some guidance as to where it configures the port replicator monitor configuration. I looked at the section Configuration screen Control Panel but it seems to be the performance of two monitors, it appears not to address the peculiarities of a laptop computer with a port replicator configuration

  Thank you

  Hello

  I have no Portege R500 but I ve used external monitor connected to my Tecra duplicator.
  Can you please tell me how you have configured previously?

  What is your external monitor set as primary monitor?

• Manager profile - can I change the Port?

  Dear community,

  I have a little problem. A customer uses an OSX Server (to El Capitan. 10.11.2 + Server Version 5.0.15).

  The problem is, there is an Exchange Server that uses Port 443, so I can't use this port.

  My first test was a Port Forwarding of incoming: 8443 to macserver:443. I can reach the server, but when I log in, then it redirects me to the default 443 ssl port.

  I have checked the ssl httpd configuration, took a look in other apache-configs... changed ports 443 to 8443... but without success...

  How do you do that? Someone had the same problem?

  Thanks in advance

  No you can not change the ports using the Profile Manager. Even if you could change the ports at the end of the Profile Manager server, you have absolutely no chance of being able to change the equivalent settings built into iOS etc devices.

  Having two or more public IP addresses different so that the Exchange Server can have its own without conflict with the Profile Manager is an option that most of the larger organizations would use.

  It maybe by using a reverse proxy server could also be an option. The reverse proxy server would transmit 443 traffic to any server, it is by looking at the URL, for example exchange.domain.com:443 gets sent to this server and the mdm.domain.com:443 is passed to the other.

  NGINX is the main reverse proxy server software.

  PS. If it is not possible to overturn or transmit proxies the other ports used for profile, i.e. the NPP ports Manager, it is possible to reverse proxy standard web ports 80 and 443.

• The Port settings parallel conclusion by program

  I have a colleague who has installed a basic PCI parallel port and he wondered if he could get the address of the port by programming?

  Windows assigns random the 090_hex?

  Kind regards

  -SS

  I believe devcon will do.

• HP Officejet Pro 8600 no possibility to configure the Port

  My OS is Win 8.1 (last version), latest version of the printer driver, last wizard to install printers used.

  My first printer "HP Officejet Pro 8600" folling down on the issue of the screen. I'm doing a swap with the same model, I have to uninstall and reinstall the full with Wizard, now I have some difficulties to recognize the printer.

  -Shortly, no communication!

  -A few times, printing find after printer communication error.

  If I go to "Properties/Port/port" I got "Error Message.

  > An error occurred during port configuration.

  > The file name, directory name or volume label syntax is incorrect.

  Could be a former key stay in the registry (with the old link to the printer)

  I have to uninstall and reinstall the wizard fuul without success.

  Now the analysis feature does not run and printing run with delay.

  Major Remarq:

  I have no problem with MAC OS 9.x to 10.10.1

  Thank you very much in advance for your support

  Hello

  The port must not be changed that way but through the HP software, it is managed by the software and such a mistake is planned during the attempt to change the port...

  Try opening the HP Officejet Pro 8600 software, and then click the Utilities.

  Click Update IP address and type the IP address of the printer, which can be found by clicking on the icon wireless/network at the top of the Panel before you the printer.

  Click on save and confirm, then close and reropen the HP software,.

  What happens when you try to scan now?

  It'll work, or is there a specific error or behavior?

  As well try now the doctor of printing & scanning HP, it is listed under the Utilties batn so, follow the steps on the screen by selecting the difficulty of analysis and let me know the results if you are still having problems.

  Shlomi

• Unable to get the port forwarding on LRT224

  Hello

  Can anyone help with setting the port forwarding on a LRT224 - he drives me crazy!

  I have a mail server running on the internal network listening on port 443 using SSL. I want to expose it to the internet on port 450

  I tried to configure the following Port Address Translation entries:

  TCP: 450 an external Port internal Port: 443 host LAN:

  UDP: 450 an external Port internal Port: 443 host LAN:

  The two rules are enabled.

  I have not setup additional access rules, since I realized that the Port Address Translation is circumventing them.

  The setting "Block WAN request" on the firewall is disabled.

  Result - NOTHING! No link, no ports open (verified with ShieldsUp!)

  FYI - the LRT224 was purchased to replace 2 DD-WRT-flashed routers, each connected to a different ISP - 1 want to automate failover rather that physically Exchange connections of my passage to the routers.

  On the other hand, the requirement for transmission of port above took 5 minutes to the configuration via DD - WRT and worked as required from the beginning.

  I spent 2 days playing with the LRT224 and have no configuration work.

  It is a basic feature! Why is it so hard to make it work?

  All help gratefully received...

  Hi Chad,

  Just to say thank you to help get that job!

  To confirm, the resolution for anyone interested:

  The configuration of Port Address Translation was correct, but the internal server that was targeted had bad default gateway on its network card (it was targeting my other router), which meant that he was not talking to the LRT224, which means that the latter did not open the ports connected to the Internet.

• Problems with static IP setting for the port forward through 2 routers

  I currently have cable internet connected to a router (Linksys E2000 w / v1.0.03 firmware). This router is connected to another router, a Linksys E3200 with firmware v1.0.02. In order to correctly forward ports through the E3200, I understand that I need to set up a static IP address on the router.

  I almost followed the steps in this video, but when I enter all the IP addresses for the static IP address settings, it allows me to access the router configuration page. I try to get the new IP address that I gave (which he tries to move automatically once I have save settings) and the connection times out. I am able to access internet otherwise, however. From here, I have to do a factory reset on the router and start from square one.

  Anyone have any ideas? I'm quite frustrated and would like to get ports forwarded so I can get my server properly set in place.

  1. If it has connected LAN - LAN you will need to disable the DHCP server on the E3200.

  2. the best option would be to use the 'bridge' on the E3200 mode (in the latest firmware) and connect the internet port to the main router.

  3. If connected LAN - LAN (or in Bridge mode) all internet related functions on the E3200, including ports are not relevant. There is no need to set up the port on the E3200 redirects. All shipping is done only on the E2000 and nowhere else.

  4. What is the address LAN IP of the E3200? What is the address LAN IP of the E2000?

• I can connect to my wireless router, but cannot get internet connectivity via Wireless. If I connect the cable to the port on the router, I get internet connectivity.

  Wireless router / Internet problems

  I am running Windows Vista Home Edition with Security Essentials.  I can connect to my wireless router, but cannot get internet connectivity via Wireless.  If I connect the cable to the port on the router, I get internet connectivity.  Is there a firewall setting that could cause this problem?

  Hello

  Your router could be suspicious here, you have successfully updated its firmware as a possible solution? And I would like to
  Update your WiFi drivers on computers. How you are positioned in the router? Are there
  obstacles in the path?

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• Access to the network of a device ethernet via the ports of the router.

  I was wondering if someone can help me with a router configuration. I have an ethernet device, a built-in Digi Connect me stack ethernet. I put the IP, subnet, gateway, etc. on this device. It has a serverver web and telnet and FTP features. What I want to do, this is the device connected to a WRT54GS router to one of the ports on the back. Then I want to connect internet routers connecting to my local network. On the LAN, I have a PC I want to use to access the web page of the Digi device through the router. The LAN has affected the PC an IP address of 3.11.201.33 and assigns the router IP Internet of 3.11.201.32. The PC is set to dynamically set an IP address. I have configured the Digi device to have an IP address of 192.168.1.100. I want to open a web page on the PC and connect a digi device. I can't get this to work. I tried to add the IP address of the device Digi to the DMZ on the router, but that did not help. How can I get from the PC via the LAN, through the router, on the port that is connected to the Digi? Any help is apprecieated!

  Outgoing FTP for multiple devices behind the router need not any special installation... you will not need to pass all the ports for that.

  You can port forward more than a device with the stock firmware digi... I just forgot how port forwarding 'niche roles' it is on the page... the WRT54G V5 has 10, so assuming that no other device in transmitted port, you should be able to forward the ports ftp and telnet for 5 devices.

• How to block the ip or the port? Linksys BEFSR41 V3

  Hello everyone im in need of help. I'm trying to block an ip address or a port from my router. I really want to get into the story on why I'm doing this, but for a good cause.

  So, far I don't know were to start on how to do it and I hope that you guys would help me through it. I am currently runnin firmware 1.04.11.04.17 7

  Thank you!

  The BEFSR41 router interface based on web Access ther.

  Go to security. the filter page.

  On this page, you can block internal users to access the Internet by entering their IP address.

  You can also block any request to the Internet at any particular port #.

  Or you can enter a MAC address from the internal user you want to block from the Internet.

  I think that these options should give, you want you want.

• Photosmart 6510 - Windows 7 - I need to the Port ID to set up my modem for wireless connection

  Printer: PhotoSmart 6510

  Operating systems: Windows 7

  Modem: Huwawei E586

  The printer configured easily to the modem for wireless connection.

  The problem I have is that my laptop cannot see the IP address of the printer when I try to configure a wireless connection.

  I am trying to add the IP address of the printer to the virtual server from the modem list.

  What is the PORT ID required by the printer?

  This information is not in the installation notes.

  I found it. It is Port 9100

• Photosmart B110 - retain and retrieve the PORT settings

  I have contected to the printer wireless to my laptop (HP, also), but whenever I start the printer, port, it connects via has changed the parameters of the laptop.  The only way I can find the port is to print a report without thread - which is a waste of ink/paper.  Is there a way to force the port changes not (preferred), or to find the number of port without printing.  I have no other wireless devices, so there is no reason that I can see the change.

  Yes.  You can set a static IP address on the printer and it will be forced to keep the same IP address, until what tell you him to change.  This document includes the steps you need for IP address static and other measures to stabilize the connection of the printer wireless.  Let me know what happens.

• See the bandwidth for the Port-Channel on Powerconnect &amp; Force10

  Reference Dell dear community,

  Y at - it a command CLI or GUI to see how much bandwidth result after having done a port channel in some port Powerconnect and Force10? Suppose we have 4 port 1 Gb and do 4 ports with 1 port-channel. So actually in this channel port have a bandwidth of 4 GB.

  In Cisco, with the command show interface port-channel 1, we get the result

  switch #sh po int 1
  Port-channel 1 is up, line protocol is up (connected)
  Material is EtherChannel, address is 0064.4026.739a (bia 0064.4026.739a)
  MTU 1500 bytes, BW 4000000 Kbit, DLY 10 usec,
  reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  KeepAlive set (10 sec)
  Full duplex, 1000 Mbps, link type is auto, media type is unknown
  input stream control is turned off, output flow control is not supported
  Members in this channel: Gi0/1 Gi0/2
  Type of the ARP: ARPA, ARP Timeout 04:00
  Last entry of 00:00:00, 00:04:48 output, output hang never
  Final cleaning of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/dumps); Total output drops: 0
  Strategy of queues: fifo
  Output queue: 0/40 (size/max)
  5 minute input rate 2000 bps, 3 packets/s
  5 minute output rate 2000 bps, 3 packets/s

  But if we do this command on Powerconnect, the just result inform port that starts from the port-channel.

  Reference Dell #show interfaces port-channel 1 short

  Ch-Type Hash Type Min-links Channel ports local FRP
  -------   ----------------------------- -------- --------- --------- ---------
  PO1 Active: Static disabled people article gi1/0/1, gi1/0/2 7 1 article
  Item in gi1/0/3, item in gi1/0/4

  Type of hashing algorithm
  1 - the source MAC, VLAN, EtherType, source module and port Id
  2 - destination MAC, VLAN, EtherType, module source and port Id
  3 - source IP and TCP/UDP source port
  4 - destination IP and destination TCP/UDP port
  5 source/Destination MAC, VLAN, EtherType, MODID/source port
  6 source/Destination IP and port TCP/UDP source / destination
  7 - improved hash mode

  Can you help us find the answer?

  Thank you

  Kind regards

  Aziz

  The PowerConnect switches do not have the ability to show as much detail as the Force10 can. The RMON tables have an interface use %, what may be the closest we can do on the PowerConnect switch.

  #show rmon statistics

  I've seen some monitoring software which was able to question the switch via SNMP and get some information of bandwidth. However, this can be a bit inconsistent, according to which switch and what software is used.

  The MIBs/OID can be downloaded with the software switch.

  http://www.Dell.com/support/home/us/en/rc959303/products/ser_stor_net/networking/net_fxd_prt_swtchs

• prnport.vbs to add and select the port

  I have the following script, where he creates a port of the printer, for example, 10.10.21.22. He created the port, but then I have to manually select the port in devices and printers. How do I update the port also?

  There is a r - updated the port, but it does not work. It is said:

  Unable to parse the command line. Error 0x1C9 this key is already associated with an element of this collection

  https://TechNet.Microsoft.com/en-us/library/cc754352 (v = ws.11) .aspx

  $GetPrinterIP = Read-Host "Enter printer IP address"
  $PrnportVBS = cd C:\Windows\System32\Printing_Admin_Scripts\en-US
  Cscript Prnport.vbs -a -s $env:COMPUTERNAME -h $GetPrinterIP -r $GetPrinterIP -o raw -n 9100
  

  Hi Tony,.

  The complexity of your concerns, we will have to refer to our Technet forums. Our experts will be happy to help you get the right answer for this case.

  Kind regards.