The hard drive capacity

Similar Questions

• Re: Tecra A7 - what is the maximum capacity of the HARD drive?

  Hi all

  Is there any BIOS, hardware limitation of a hard drive replacement for Toshiba Tecra A7? I'm looking to install 500 GB hard drive. Will it work?

  Thank you
  Matt

  Hello

  As I know there is no limit of capacity on the HARD disk for Tecra A7 already has a SATA interface and a controller for the HARD drive.

  So, theoretically, 500 GB should work fine, I don't see a reason why it shouldn't work.

  But you could give us a feedback here, how it works with 500 GB! ;)

• Satellite 2800-200; is it possible to upgrade the memory and HARD drive capacity

  Hi all

  my computer is a Toshiba Satellite S2800-200 (old) and I wont to ask if it is possible to upgrade memory capacity and disk.

  Thank you

  Of course you can upgrade these laptop parts.
  The laptop seems to be equipped with an internal memory which is not removable.

  http://www.orcalogic.co.UK/ASP/ProdType.asp?ProdType=7168&ft=m&St=3
  According to the website above, you can use only one memory for an upgrade slot.
  You can use the 144-Pin PC100 SODIMM 128 MB module. It's max.

  I m not 100% sure on the HARD drive, but as I m not trunk not the laptop came with 10 GB HARD drive. Generally, a 20 GB HARD drive should be possible.

  Good bye

• What capacity of the HARD drive in 1670CDS

  New, I HAV Satellite 1670CDS with Phoenix BIOS ver. A 1.07.
  My drive HARD broked down. I have to buy a new one. What capacity of the HARD drive will be detected BIOS corectly? How many GB of hard drive I can buy?

  Thank you very much.

  Hello

  This kind of information can give you just authorized partner. I found the info your device comes with 6 GB of HARD drive. Am I wrong?

  I'm sure you can use 10 or even 12 GB of HARD drive without any problem. If you want to use more than capacity, it is possible that it will not be recognized by the BIOS.

  I found an offereor which has guaranteed that even at 30 or 40 GB hard drives can be used on older models, but the BIOS should be handled with the special tool and is not for free.

  Good bye

• Qosmio G30 - capacity of the HARD drive even after disable RAID

  Hi all

  I have a G30 with two hard drives, which were broadcast in RAID 1 configuration for a year now. For RAID 1, I activated the mirroring and everything worked perfectly.

  However, I'm now running out of space so I turned off mirroring using RAID console.
  My question is "why do I always see the same capacity of HARD drive when I go on my computer? I hope that there is a simple answer to this.

  Thank you for Uncle Bob.

  Can you see the drive in disk management?
  Perhaps the HARD drive is not enabled or needs to be formatted.

  And the BIOS recognizes the another HARD drive?

• Is it possible to analyze infrastructure were returned by the device of scanning the hard drive size/capacity

  Is it possible to analyze infrastructure were returned by the device of scanning the hard drive size/capacity

  Well, Foglight can certainly, as indicated above, Robert fired in a mode without agent disc information.

• Satellite Pro A120 - Maximum capacity of the HARD drive?

  HI - new here. I have a:

  Toshiba Satellite Pro A120
  Model PSAC1E-04H00VEN number

  It's less hard drive. I have a 160 GB spare hard drive but when I try to install this using the recovery disc, the operation simply sticks on the "Please wait..." message. ». The specification for the A120, I noted that it supports drives of 40 to 120 GB. Which is strictly true and so why can't I just install this 160 GB drive?

  Thank you.

  Hi Lapitup,

  Usually the 160 GB should be no problem because the laptop supports the SATA interface and there is no limit of ability so that you can install each HARD drive.

  Be interesting to know what HARD drive you have installed exactly and if you tested on another computer because the HARD drive itself could be the problem and not on the computer. If the disc is defective recovery disc can t be installed so that you get an error message.

• Wizard BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?

  This has two questions:

  1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.

  2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.

  3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.

  Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.

  The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.

  Then there is the BootCamp partition on the HARD drive partition #2.

  Is there a way to get what I need?

  That is what has been described in this notice of two canoes?

  Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3

  n-on-a-3-TB-fusion-drive http://twocanoes.com/Winclone/support/installing-Windows-on-a-Boot-Camp-partitio

  Thank you.

  After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.

  Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.

  A. take backup

  1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.

  B. fuse out of the merger in two physical disks drive: SSD + HDD

  1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)

  Cs diskutil list

  2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive.  Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.

  I hit this issue too.  To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:

  Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)

  and repeat for disk1/dev/disk1 which is the HARD drive in my case).

  This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.

  2 create independent partitions (non-fusionend) for the installation of OSX.

  Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".

  3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".

  C. install on the HARD disk as drive didier autonomous not fusion.

  1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.

  D. use BootCamp Yosemite f5 to install windows.

  1. launch Yosemite bootcamp.

  2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software.  Do not click on the last box to install or remove windows pie creating real bootcamp partition again.

  3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.

  4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use.  Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model).  Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.

  -From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.

  -Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.

  -Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.

  5. open Boot Camp Assistant again and only select the third option, install Windows 7.

  It will show you the screen to select what installation disk, select HARD drive.

  Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.

  For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.

  Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio

  6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.

  7. once the installation is complete, check that windows is functioning correctly.

  E. Si you want to upgrade to windows 10 Windows 7.

  1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page.  Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE.  Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.

  2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.

  F. reinstall OSX El Capitan

  Once your target windows system (if windows 7, windows 8 or windows 10) works very well.  You can continue to create again your Fusion drive and reinstall OSX El Capitan.

  1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.

  6 type the 'diskutil list' command to list all disks and partitions.

  The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.

  The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.

  G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc

  1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.

  2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.

  3. on the selection screen, select start Yosemite OSX install drive.

  4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.

  5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.

  Cs diskutil list

  6. in the terminal, type commands to delete logical drives from basic storage.  Note: All data will be destroyed in the logical drive.

  diskutil cs deleteVolume Logical Volume ID

  CS diskutil remove logical Volume Group ID

  7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.

  / dev/disk0 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * GB 121,3 disk0

  1: disk0s1 EFI EFI 209.7 MB

  2: Apple_HFS GB SSD 121.0 disk0s2

  / dev/disk1 (internal, physical):

  #: NAME SIZE TYPE IDENTIFIER

  0: GUID_partition_scheme * 3.0 to disk1

  1: EFI EFI 209.7 MB disk1s1

  2: Apple_HFS 1.7 Untitled TB disk1s2

  3: disk1s3 Apple_Boot Recovery 650.0 MB HD

  4: Microsoft database BOOTCAMP 503.0 GB disk1s4

  5: Apple_HFS 801,4 Untitled GB disk1s5

  8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.

  diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5

  Note: Mark the group id of logical volume shown in the results.

  In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.

  So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2

  9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.

  diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%

  10 command "diskutil cs type list" to check the resulting fusion drive created.

  CoreStorage groups of logical volumes (1 found)

  |

  + Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E

  =========================================================

  Name: LVG

  Status: online

  Dimensions: 1815635525632 B (1.8 to)

  Free space: 90112 B (90.1 KB)

  |

  +-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3

  |   ----------------------------------------------------

  |   Index: 0

  |   Disc: disk0s2

  |   Status: online

  |   Dimensions: 120988852224 B (121.0 GB)

  |

  +-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E

  |   ----------------------------------------------------

  |   Index: 1

  |   Disc: disk1s2

  |   Status: online

  |   Dimensions: 1694646673408 B (1.7 to)

  |

  +--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9

  ----------------------------------------------------------

  Encryption type: no

  |

  +--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10

  ---------------------------------------------------

  Disc: disk2

  Status: online

  Size (Total): 1809780178944 B (1.8 to)

  Reversible: no

  Name: Macintosh HD

  Volume name: Macintosh HD

  Content indicator: Apple_HFS

  LVG Type: Fusion, sparse

  11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.

  12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.

  13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.

  14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.

  15. yet once please take personal responsibility on damage if you follow the instructions in this article.

• Sudden disappearance of the contents of the hard drive

  After I've upgraded to the latest OS X El Capitan Version (10.11.5), one of my hard disks (called Audio video) has ceased to show everything!

  On the other hand when I look at the disk (right-click & Get Info) system information the system gives me all the Info for the disc:

  Audio-video

  Updated the: March 27, 2016 at 11:06

  Genre: Volume

  Created the: October 5, 2006 at 17:31

  Updated the: March 27, 2016 at 11:06

  Format: Mac OS extended (journaled)

  Capacity: 999,86 GB

  Available: 26,55 GB

  Used: 973.307.651.947 bytes (973,31 GB disk)

  More information:

  Last login: 18:27, 28 April 2016

  When I open the drive on the desktop, the entire folder looks absolutely empty. When I tried to make a new folder in the space of the disk (right-click and new folder) the following message is displayed:

  The operation can ' t be completed

  An unexpected error occurred (error code - 50)

  When I open the hard drive the drive of "Audio vidéo" first aid program "sees". When I clikced first AIDS the following message is displayed:

  «Run first aid in «Audio video "»

  The process has no first aid. If possible, create a backup copy of the data on this volume.

  Update startup for the volume if necessary support services.

  Impossible to mount the removal of volume for repair.

  The operation has failed. »

  Any help will be much appreciated

  Thank you very much in advanced

  What Format is the external hard drive?

  Do a Get info on this drive or folder, what rights it lists?

  Some solutions info jere & possible...

  An unexpected error occurred (error code - 50) when registering at ext HD.

• Can Tecra M9 - I put the HARD drive?

  I currently own a * Tecra M9 - 15I * (part PTM91E-04R03TEN No. - discontinued model).

  When I bought the laptop, it came with a 120 GB HARD drive. I am running Windows Vista Business which fills almost half of the hard drive. I want to upgrade the HARD drive because I think the upgrade to Windows 7.

  Is it possible to upgrade the HARD disk? If so, what are the compatible HARD drive options? If I do not change the HARD drive, this will affect the status of the guarantee of the laptop? for example, I currently have a 3 year warranty and the warranty upgrade HARD drive Toshiba?

  Hello!

  Of course you can upgrade the HARD drive on your laptop and this doesn t affect the warranty. HDD upgrade isn't complicated and so it can be done by the user.

  To swap the HARD drive, you need only remove the screws to the HARD drive Bay and remove the HARD disk cover. Then you can see the HARD drive and swap it.
  I don t know you, look in your user manual. You will find interesting information and photos on this topic.

  Theoretically, you can buy each HARD drive you want. On interface SATA there is no capacity limit.
  I have good experiences with Hitachi and Seagate hard drives.

  Good bye

• Satellite Pro 4280 - what is the size of the HARD drive?

  I just bought a laptop Toshiba Satellite Pro 4280. According to the manual, it should have a 6.0 GB HDD but in my computer it is shown as having only a 1.34 GB capacity.

  PS I formatted the disk to remove the former owner data and operating system and you have installed Windows 98SE

  [Edited by: admin]

  Hello

  Satellite Pro 428Xcdt was certainly delivered with 6 GB HARD drive.
  Are you sure that you have checked the size of the HARD drive correctly?

  I guess the 1.34 GB is a free space on the HARD disk.

• Max on Portege 3480CT HARD drive capacity?

  What is the hard drive of greater that I can install it on a 3480CT portege? can I write DVD with an external burner (USB 2.0)?

  Hello

  You will be very happy if someone can give you specific info on the maximum capacity of the HARD drive for this model of laptop. This info can give you a few specialist upgrade for laptop, but I think that 20 or 30 GB maybe are no problem.

  I use the external DVD burner too, but not ultra slim but desktop engraver special cardboard. I don t use USB. FireWire is much faster data transfer rates and I use the firewire port on my Satellite.

• Satellite A200-1AI - Windows has detected the hard drive error

  Hi guys.

  I think its time I replaced my hard drive. Ive done all the checks and his return there is no errors with the hard disk, yet whenever I connect I get a message saying that there is.

  I guess that's only a matter of time before things get more serious.
  Its just now that it unattached restarts automatically.
  Ive gave my laptop below specifications and the specifications of the hard disk drive.
  I do not know which drive hard im supposed to be looking at.

  I don't want to buy one and then duty send because its incompatiable.
  Ive done some reading on the internet and he says I cn buy any production, but I need to know wheather its an IDE or SATA, what are these and what do mean? How can I find out what my current car?

  Also should I look for a hard drive with the same speed? It doesn't matter if its fatser?
  Wise, capacity is also ok for larger, will my laptop be able to handle it. Thanks for help

  MODEL NAME: Toshiba Satellite A200-1AI
  MODEL NO.: PSAECE-00U00JEN

  HDD SPEC:

  TOSHIBA MK2035GSS HARD DRIVE
  CAPACITY: 200 GB
  CERTIFICATION: S.M.A.R.T
  DrRIVE ROTATION: 4200 RPM

  Hello

  The Satellite A200 supports the SATA HDD controller.
  That's why you need to buy a SATA 2.5 HARD.
  The value of the rmp is not really important for compatibility issues with the 4200 RPM HDD or more is possible and compatible.

  SATA controller not limited to any size of HARD drive, you can also use large drives.

• My iCloud is full and I would like to spend on 5000photos on the hard drive and then remove them to iCloud.  How do you do that?

  My iCloud is full and I want to transfer most of my 5000 images in the cloud on the hard drive on my iMac which is about 10% of storage capacity.  How can I do this?  Thank you

  1. Photos > Preferences > iCloud > iCloud (original Dungeon) photo library
  2. Wait for them to download

  If you want to remove the cloud, you can do two things:

  System Preferences > iCloud > manage > photo library > remove and disable

  or

  iCloud.com > pictures (select and delete)

  Please note, however, if you enable iCloud library again at any time in the future on your Mac, all the photos on your Mac will download again. You may find that buying more space iCloud is the best answer for you.

• Equium L350 - 11 d - how do I delete the second partition on the HARD drive

  How can I delete the second partition that came with the laptop, so I can use the full capacity of computers HARD drive?

  I feel that this partition is their because I have not created a DVD of recovery he would remove the partition once I created the recovery DVDs.

  The score contains a folder of HARD disk RECOVERY and in the folder says do not delete or change this folder or files.

  I have a Toshiba Equium L350 - 11 d

  As you have already said that the second partition contains the HDD Recovery folder if you would remove this partition you will not be able to create the recovery DVD and would not be able to recover the laptop HARD drive.

  Therefore, you must create the DVD before recovery would remove anything from the second partition on the HARD drive.

  After you create the DVD recovery successfully, you could remove the partition and could add the free space on the HARD disk on the first partition.
  This can be done on disk management!

  This is a useful page for Microsoft:
  [Using Windows and procedures: Vista HARD disk partition | http://windowshelp.microsoft.com/windows/en-us/help/d9a4d35e-efdf-406c-a049-0860180129a71033.mspx]

  Good bye