The power led codes

Similar Questions

• Portege R100 stoped working - the power LED flashes error codes

  I have a R100 that has suddenly stopped working.
  The power led (clear amber with the image of the power wire) flashes what appears to be an error code of 5 flashes with a long pause on the last flash, followed by 3 flashes.

  That - what it means, and where can I get a list of all codes error?

  I changed the main battery, changed the spare battery and changed supply - and again, I get the error permanently. I was not able to power the laptop at all since it started. When you press the power button / nothing happens.

  I hope someone on this forum has some information that may help you diagnose this problem. Tech support representatives Toshiba post here?

  Thanks in advance.

  Hello

  I m not a R100 owner but to me it looks like a card mother malfunction because you have already tried to exchange the battery and the AC adapter.

  In this case, the best solution would be if you go to an authorized service provider. Technicians can consult the specifications and they know what means this code I think.
  Here it s only a user to user forum and I have never seen anyone from Toshiba again.

  Anyway, here you can search for the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good luck!

• Qosmio X 500 does not start and the power LED is flashing every 5 seconds

  Hello
  I need help my X 500 does not start now. I tried to launch the NB as usual and suddenly the X 500 start or even power up.

  If I press the power button / stop it makes no noise, the power LED on the button and the second power LED just bliks once and turns on and keep blinking every 5 seconds.

  I tried to:
  * Remove battery and power up with AC only
  * power only to batteries
  * remove the battery power button hold for 30 seconds and over power with AC, battery only athen

  but it did not help.

  I checked the LEDs AC & battery, but they do not blink, they are just RED, so there is no problem in battery or AC.

  No idea where could be the problem?

  Thanks for help
  Frantisek

  Hello

  The failure of RAM could be the reason for this behavior of the laptop.
  Remove the RAM modules with good modules tested and check the functionality of the laptop.
  In the case of RAM isn t the troublemaker, the motherboard could be affected.

  Good luck and share your experience with us.

• (Model: D6000 ac750) Only the Power LED comes on after start

  Hello

  When I turn on my router, only the power LED comes on, no other LED lights. Ive been waiting for awhile as well, switching router on and outside, from time to time but its still the same result, only power LED lights

  I think this happened because of the failure of an attempt to upgrade my modem firmware, which I clicked on another tab, stop the download. After that, the modem turned off and only the power LED came on when I switched it back on

  any help would be apperciated, thank you

  NotGTAV

  I would say that the modem can be bricked you wish to contact Netgear phone support if it is still under warranty.

  http://support.NETGEAR.com/general/contact/default.aspx

  DarrenM

• Satellite A10 dies after the power LED blink

  Hello

  I have a problem with the power supply of my Toshiba Satellite A10. Sometimes, after the computer sat for some time, I have a problem with the power. The "plugged power cable" - LED will start to blink and shortly after, the computer just dies.

  It can also have the time to go into a lower energy state before he does. When it happened once, it will most likely happen also when I restart the computer, but after a much shorter time. WXP won't even have time to start. If I stop to select the source of start-up, the problem will occur anyway, this isn't the software. It should also be noticed that when the computer is not turned off, the 'smart power' - is on correctly.

  I know that my battery is not very good. Completely loaded, the computer can run for maybe 3 minutes with only the battery. I know that I must have a battery connected, even if I use the power cable, but this occurs even when the mine problem. The battery would be pretty bad not even allow me to use the computer with a cable?

  It should be added, that sometimes I can use the computer for long periods of time without this problem to happen. I also have a problem with the battery not being not properly in physical contact with the pins of the computer, but this isn't the problem here, because I have the same problem with the battery removed and me holding the battery in place.

  Thank you for your help.

  Andreas

  Hello

  You description is very long and detailed and it of still not easy to say what's wrong.
  Usually, the DC-In witness lights up green when DC is provided FRO the AC current. If the output voltage of the adapter is abnormal or if power outages, this indicator flashes orange.

  So I think that is your AC adapter malfunctions or there is something wrong with the electronic power supply on the motherboard.

• the power led stops working...

  in my macbook pro (early 2011) during the update of the el capitan 10.11.2 to 10.11.3 power led to go to Flash mode & stops working after update.can help me! ?

  The usual remedy is to reset the SMC. Read all the steps.

  Before resetting the SMC

  Try each of the following steps in this order before reset you the SMC. Test the issue after execution of each troubleshooting step to determine if the problem persists.

  1. Press Command + Option + escape to force quit all applications that are unresponsive.
  2. Put your Mac to sleep choosing the Apple () menu in the menu bar at the top left and then choosing sleep. After that he went to sleep, to wake up the computer.
  3. Restart your Mac by choosing the Apple () menu in the upper-left menu bar, then selecting restart.
  4. Stop your Mac by choosing the Apple () menu in the bar menu at top left and then choosing stop.

  Resetting the SMC on laptops with a battery you should not remove on your own

  1. Shut down the computer.
  2. Plug the MagSafe power adapter to a power source, connecting to the Mac if it is not already connected.
  3. On the built-in keyboard, press Command-Option-shift keys (left side) and the power at the same time button. Power adapter light can cycler deactivation / activation once.
  4. Release all the keys and the power button at the same time.
  5. Press the power button to turn on the computer.

• How we touch the power LED cable (model SR5702F Office)?

  How we touch the power cable LED on HP 517069-001 (model SR5702F Office)? All but one connector are color coded. Who is that a problem is this is a single line with an end connector have covered the (black). Thank you

  The pinout is a follows:

  

• DELL UltraSharp U2515H Monitor - fixed the power LED mode indicator sleep?

  Hello

  I just bought a monitor DELL UltraSharp U2515H 25 and in the course of the day before (Mini DisplayPort) Power LED flashes during the standby time.

  Can you tell me if this is normal?

  This indicator returns to fixed when using the display and it is possible to turn off the light while turning on the unit via the OSD menu. (Page 41 of the french DELL user guide)

  The link provided above a video illustrating the behavior of the screen (IMG_7073.MOV)

  Manufacturing date: Apr. 2015
  Review: REV A01

  Thank you in advance for your support.

  Kind regards

  Stone

  It is normal to blink while it is in standby mode. White light indicates the monitor is on and fully functional. A glowing white light indicates the power saving mode. Did you put the Power button LED "off during active?

• My hp Pavilion p6230y died. It will not start. The power LED button does not lite.

  The power supply is turned on, and all voltages are correct (measured). The fan turns on when you press the power button and I can feel the rotation of the disk and it's hot. I stripped naked essential system, nothing that the keyboard wireless & mouse, HDMI connector to monitor. I cleaned all the dust from the inside of the computer. I reinstalled the CPU chip. No beeps at all coming from the motherboard. The heatsink is stone cold. I suspect either chip CPU & and/or motherboard. Anyone have any ideas?

  Replaced the motherboard. Problem solved.

• Dell vostro laptop 1540, he does the power LED light really, he ran over by a car

  I have a laptop dell 1540 he don't really connect the supply lights, I guess that flickers on and off voltage and the led on the hard drive did the same thing to

  the hard drive is clicking on screen remains black, that nothing comes, or whatever it is, I have a new motherboard and a new screen put because

  He ran over by a car I don't know if it's the hard drive or what it is can someone please help thanks

  Hello

  Looks like you need a real computer store (the one that is internal
  service on Dell laptops) or Support of Dell. Not a lot of laptops could survive being
  crushed by a car so he can be ready for the scrap.

  Dell support
  http://support.Dell.com/

  Dell support drivers - product manual & warranty Info (left side) - and much more
  http://support.Dell.com/support/index.aspx?c=us&l=en&s=DHS

  Dell forums
  http://en.community.Dell.com/forums/
  I hope this helps.

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle=""><- mark="" twain="" said="" it="">

• what it means if the power LED flashes red, that I am plugged into the power outlet

  help what is a flashing red light on average power

  Yes, the batteries in laptops are like any other rechargeable battery, they have a life cycle. Since the bits of information so far, it sounds as if you do not want to replace the battery. You can see what is essentially a stack to the page linked below:

  How to replace your laptop battery
   http://www.Dummies.com/how-to/content/how-to-replace-your-laptop-battery.html

  What I would say has visited support site for the manufacturer of your laptop; using your specific model name/number search for laptops support page. You should be able to get some type of documentation that will explain the flashing red light. Also get the specifications for the battery of your specific model (see technical data). Though on checking support site for the manufacturer to see if they have their own forums, if so you may be able to find details about the light, and what is involved in the specific battery in your laptop.

  Computer manufacturers
   http://Windows.Microsoft.com/en-us/Windows/help/contact-support/computer-manufacturers

  Kind regards

• Satellite A65-S065 - button Power LED is blue & amber at the same time

  1st off I have a S065 A65 and worked well after a replacement motherboard, my fault, he had to be replaced.

  In any case, I have the power button LED is blue & amber LED light up at the same time. Anyone has any idea as to what it means, or maybe I'm going into something, I don't know what it is and it should be reset at the back. Any ideas?

  Thank you
  Ben

  Hello

  I checked the manual of the Satellite A65 and there I can find information that the Power LED blinks orange indicating the machine is in standby mode. So for me it sounds like that your laptop is in sleep mode.

  What happens if you click Start > stop and choose the closing down in the menu drop-down? Normally, the power LED button must be turned off and also the laptop is in sleep mode.

• power led on the rear of the computer the power button / stop turns on, then turns off.

  I have a HP TouchSmart 610-1015xt.  The light on the transformer power is on, but not exactly brilliant (I think it's good, but not sure).  The light next to the power input is on.  When I plug in the power, the power led lights up for a couple / few seconds then turns off and does not turn.  At no time the computer capable of running and it does no whether noise (no fans, no beeps, no attempt to start.

  Any suggestions?

  Figured it out.  Apparently I have reset the battery internal and then unplugged the power button circuit and then he started upward.  The only problem is that now it will restart automatically every time it is closed or even sleep.  I'll start another forum on this issue.

  Thank you for your help.

• Satellite P30 will not start, but shows the power on LED and fans work

  I work on a P30, radiator cleaned, the basic form of new fine thermal compounds, worked for a few hours, then turned it off and move the power LED lights, fans, cd rom works, but it is she, no display, no boot, nothing.

  Any ideas on how to solve this problem would be a great help.

  Plug

  P30
  P4 3.2 ht
  1 gig of ram, tested.
  XP pro

  Hello

  On this path, it is not easy to say what can be the problem and just inquiry may help, but from your description, I'm afraid that there are some critical material damage. It may be something wrong with the power supply (motherboard) or perhaps is the grilled CPU if you have done something wrong with the thermal paste.

  Sorry, but I think you should contact the partner customer Service in your country and check it properly.

• HP Envy 15 "touch screen power LED appears, but the fans does not and the screen does not light

  Hello!

  I'm a student in computer engineering at the University of Waterloo 1A, and I run a very serious problem with my HP Envy 15 "TouchSmart laptop computer running Windows 8.1. It is a problem that just started today, and I'd rather have a first support here before going to see the technical support Office sometimes tomorrow. It has to do with the screen and the fans where the Power LED lights in white, just as when the laptop works properly.

  (I have warranty on the laptop when it was purchased last June, except that if I find that I need to get a replacement, I'll lose all my work, I did on that since I started my semester.) It's so silly of me not to have all my work saved on a backup, because I have an external hard drive. Problem is, I've had too many problems in getting myself organized, I'm not being open-minded as I should, and worse, I'm not a balance between life and work at home.)

  Before I had my MATH 117 conference (Calculus 1 Engineering), I was in a nearby lab where my laptop was open and turned, works correctly. I've had NetBeans IDE running since I wanted to work on the second part of my current assignment of CS 137 (principles of programming). Because it was almost time for my presentation, I closed the laptop by simply moving the screen down on the keyboard, where it goes into mode 'sleep'. (Whenever I flip to the top of the screen, the laptop is supposed to return, and the sliding screen of Windows 8.1 connection will appear.)

  When I took my seat for reading, I wanted to spend a little time to work on my programming assignment. However, after the reversal of the screen to the top, instead of having the login screen appears, I encountered the problem: the power supply light is showing a white light, but I don't hear the fans between the ventilation openings on the left side of the laptop and the screen does not light. I tried to take the power for several seconds and once button at least 10 seconds, except that the power light continues to display on a white light. The Commission of the Wi - Fi light is not displayed.

  Whatever it is, I don't want to take out the battery because I have that on my last laptop, and it's from there that I couldn't turn to the former, a new market. If I leave the Envy laptop battery, it will short-circuit the connections between the battery and the computer, and so several components will FRY. For now, what I do let the laptop is to empty the load on the battery. Then, once I noticed that the power light does not project a white light, or plug in the AC adapter and try turning the laptop on the power button.

  It will take a little while for the circuit drain the load on my battery but...

  Anyway, please would you be kind enough to help me with this problem? I would really appreciate if you can give me several recommendations. Thank you!

  Hello @GregPDesWHP,

  Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the Forums of HP, I would like to draw your attention to the Guide of the Forums HP first time here? Learn how to publish and more.

  I read your post on how your laptop is not on, and I'd be happy to help you in this case!

  In order to restore the features of your computer once more, I recommend you follow the steps described in this document on the computer does not (Windows 8). If the problem persists after having exhausted all the steps in this document, I recommend you contact our technical support at the 800-474-6836. If you do not live in the United States / Canada region, please click the link below to get help from your region number.

  http://WWW8.HP.com/us/en/contact-HP/WW-phone-assist.html

  I hope this helps!

  Concerning