The Linksys BEFSR41 V2 Firmware upgrade help

Similar Questions

• I have the first 13 items. I want to export in the .mp4 format. 14 upgrade help me?

  I have the first 13 items. I want to export in the .mp4 format. 14 upgrade help me?

  1997viper wrote:

  I have the first 13 items. I want to export in the .mp4 format. 14 upgrade help me?

  Here is the link to the Premiere Elements forum:

  First Elements

• The SG300 - 28 p - Firmware upgrade error

  Greeting is I downloaded Sx300_FW_Boot_1.4.0.88 update of firmware for switch SG300 - 28 p. The MD5 of the file signature match as listed on Cisco, but when I'm the download of the firmware (file .ros) to the switch I get the error message:

  Bytes transferred: 7011840

  Status: Failed to copy
  Error message: copy: the code SW file size is more

  Anyone else having the same problem? No work around?

  Thank you!

  Parth.

  Hello

  I like to think to upgrade the bootloader file(sx300_boot-13506.rfb) first, before trying the firmware. Boot loader are on the same zip folder as the firmware.you can use TFTP server to upgrade the bootstrapper.

  Interface WEB SG300 Cisco > Administration > file management > TFTP... When you select TFTP option for the fw 'BOOT' button is now available. Just type the name of the file and it should load the boot firmware.

  concerning

  Deborah

• Problems with the new modem DSL and Linksys BEFSR41

  My Speedstream modem died and I had to buy a new modem.  At this time of year, it is difficult to find exactly what I wanted and I ended up buying a D-Link DSL - 2320-B.  I got the Linksys BEFSR41 (old version 1, I think) for years and it has always worked well.  I have problems to get an internet connection through the router.  With the modem connected directly to the network card, as now I have no connectivity problem.  I had to change the IP address on the Linksys BEFSR41 192.168.2.1, as the modem is 192.168.1.1, 192.168.0.1 as the old Speedstream.  I couldn't see a way to change the IP Address of the new D-Link.  I have my ICS TCP/IP set to auto obtain IP and DNS.  I was previously created for a fixed IP of * provided by the router.  Even with the setting on the router to "Obtain an IP address automatically", I can't to the internet with the router in the middle.

  Any help will be appreciated.

  Your modem is a combination of the modem and the router. The problem occurs when you try to connect another router behind this configuration and end up having 2 servers dhcp and nat 2 (for port forwarding and other issues, creating in some cases where even branded products use ip addresses will clash and devices will not connect at all when him are interconnected).

  To avoid the situation described above, it is recommended that you enable the full Bridge mode on the modem / router that you currently connected to the internet and let your new wireless router controls all the functions within your local network and the internet connection (you must enter all the details in the new router, including Internet service provider username and password).

• SGE2010 - Firmware upgrade and config does not save

  Hi all

  I have a few questions, but ill start with what im trying to achieve.

  With the help of the EMS 2010 for Microsoft NAP with 802.1 x auth for access to the switch, which has led to some questions

  What I have: an EMS 2010 48 port switch firmware 3.0.0.17

  Firmware update: to ensure im not having not problems due to the old firmware, I tried to upgrade using ros_ls1_bp_ge_bx - 3020.ros to 3.0.2, by downloading the file through TFTP, the transfer is complete and that's all, nothing happens.

  Restarting the device: as part of the upgrade process, I thought I might restart, so I rebooted and found that all my settings were cleaned, as if a reset occurred... and add further pain, the backup of the settings I had taken do not appear to introduce themselves with a new request.

  NAP support: so I tested my server NPS (RADIUS) with NTRadping.exe and everything is good, however I can't the SGE2010 to talk to it... the authenticator State in the web interface is still listed as initializing... I'm not sure if it is a simple mismatch (where the attempt of a firmware upgrade), a tag that should be on the side of RADIUS or switch misconfig.

  So, in summary:

  (1) how the hell you upgrade the firmware?

  (2) why are none of my saved settings to restart the device?

  (3) if anyone one of them puts up with PAN and has all wisdom of bone beads, let me know.

  Hi Ben, once you update the firmware, you need to go to the active image, apply the second image. Restart the unit. Regarding the configuration of switch, you must save the configuration running at startup configuration

  Admin-> file management-> copy files (running at startup)

  -Tom
  Please evaluate the useful messages

• The WAG54GS Firmware upgrade problem

  Hello

  I am trying to update my firmware using the files provided on the linksys site. I have entered my serial number of the router correctly and chose the model of the good version (v.1.1) and downloaded the firmware file. I have connected my router configuration page, selected upgrade firmware and selected the id of the file downloaded. He got about 10% in the upgrade, and then he said it's the wrong file for my router. I currently have Firmware Version: V1.00.12 installed and I try to install the firmware Ver.1.01.03.

  Please can someone help?

  Marc

  Hi again,

  I feel such a fool as I now installed firmware annexed. As already mentioned by Kate, I wasn't directing the update firmware specifically for the IMG file.

  Ah, well you live and learn

  Your timidly

  Marc

• ERRO 'bad gateway entered' after firmware upgrade BEFSR41

  I have updated the firmware on my router Linksys BEFSR41 V4.3. On this router I used Statis IP (if DHCP active). It worked well on my network, until this upgrade. Now when I try to ad another static IP address, or when I want to change something in the Routing tab, I get this message " bad gateway entry! It should be the same WAN IP subnet "." Strange because I have not changed anything in the settings.
  I did a full reset on the router, still the same problem.

  Any suggestions?

  Enable the DHCP server on the BEF. That's all. There is no need of any static routes in this configuration.

  If you enable the DHCP server, either change these static IP 192.168.1.100 etc. for addresses outside the server DHCP address pool (default 192.168.1.100 - 149) or adjust the DHCP server address pool, for example to change IP address of 192.168.1.100 DHCP start 192.168.1.10 or 192.168.1.200 or whatever you want. The important thing is that static IP addresses are not inside the DHCP server address pool.

• Problem the firmware upgrade failed WRT54G v8.2

  Today I tried to upgrade my WRT54G Router v8.2 for the latest Linksys firmware. But the upgrade was repeated each time when the progress bar reaches about 75%. It lasted more than 30 minutes and I had stopped the upgrade. Then the router has stopped working. I have reset and hard reset the router. I also tried the method of tftp to upgrade the firmware again. But the problem is still there. When I ping 192.168.1.1, I always get the message "Destination host unreachable". Could someone help me solve this problem? The power and light of the ethernet port light are always on. Is it possible to solve the problem? Any information is appreciated. Thank you very much.

  Do not use the wireless computer to update the firmware. Hard-reset the router for 1 minute and try this link and check if it works...

• LaserJet M4345 MFP firmware upgrade failure using the HP Download Manager

  Hi all

  I have a LaserJet M4345 multifunction printer, and I tried to see if there is any updated firmware for the printer.
  When I try to access the web configuration interface, I see that the printer is running a firmware with 20070213 code 09.071.8

  I downloaded the software from the HP Download Manager to try to update the printer automatically with a simple procedure.

  The program finds the printer and said that she needed upgrade. He showed that the printer is model J7949E and current firmware V.33.14 while the update of the Firmware version has been V.33.21

  I leave the program to start the process of update, but as soon as I said to start the update immediately (do not), a new window will appear showing the status of update and it closed after less than a second, replaced by another saying that the firmware update was complete.

  Although I was skeptical about the process in so little time, I tried to check again the printer web configuration interface, but it showed that the firmware was always the same, I saw earlier (20070213 09.071.8). To try to detect the printer from the Manager software download HP found that the printer was still need upgrading (and asked me if I wanted to do now). Try once led to the same results.

  I tried to restart the printer, the program and the computer with no result.

  I'm running Windows 7 32 bit and the printer is connected to the router which I connect this pc wireless.

  If I can provide any other information, please let me know.

  Thanks in advance for any help you can provide.

  Piero

  Hey Unreal, the product that you have is a printer. These commercial products can be a little tricky. For the best chance of finding a solution, I would post in the forum for HP Business Support.

  You can find the Board Commercial LaserJet here:

  Business - LaserJet HP Support Forum

  Take care!

  Sean

• Why is the Linksys help number a scam?

  Yesterday I call number help Linksys and had someone in Saudi I understand just to help me to re - connect my Extender (it has been disconnected and the software did not work for the re - connect).

  Because it was the number of help Linksys (directly off the Linksys website 888-351-0767), I thought I should "trust them" (read on).

  He proceeds to tell me that my wireless network was taken over by foriener IP addresses, and the reason for my signal strength was so bad & erratic.

  And I wanted to use a service of their of which would allow him to solve the problems that I had.

  I agreed because it was using Linksys partners...

  He then showed me some googling turns out he told me was the truth.

  Then, he led a program of DOS shell and found all the problems I had while explianing for me of how these foriener hijacked my computer & wireless network.

  Then he told me he could fix everthing for $69.99...

  I didn't say a Word, I just turned my computer off (now the Start button until it is off).

  Then when I rebooted, I got its software automatically restart.

  I found a way to stop their software by searching for some answer on my cell phone.

  This seems to be a number of scam, please let everyone know!

  Linksys expected appoligize to me for this kind of behavior...

  I'll get hard customer happiness when I decide to move to a new wireless router.

  Thank you

  D

  Vince_02,

  I looked at the link, photos of technicians are similar to the language of the person who spoke to me.

  Not unless every one of them was fluient in broken Islamic/Indian/English, if so they should get a price for their perforamnce!

  Note:

  Sounded like there were at least 10 other people + background that "were" fluient Indian/Islamic all tell the person what to do next.

  Seriously,.

  Thanks for the comments and help guys.

  D

• After restart of the firmware upgrade

  Hi, I need to update the firmware on my controllers PS6100 EqualLogic.

  I found the instructions on how to do it and everything seems straight forward to do so via the GUI.

  I noticed there is a necessary restart after the firmware has been applied. Does this mean I have to gracefully shutdown the virtual machines running on my SAN LUNS? My iSCSI connections will be closed/broken during the restart of the post firmware upgrade?

  Thank you, Oliver.

  Hello Oliver,.

  In the same area download notes firmware and release is another PDF, entitled ' iSCSI initiator and optimize your SAN environment for high availability operating system considerations ", which includes some key parameters that will allow your computers virtual and servers through the failover time.  It is important that not only the Firmware update, but in the case of an unexpected failure due to a failure of CM.

  More if you use VMware ESXi, there is a best practices PDF for that as well.  In addition to better manage the failover, these changes have shown to improve performance as well.

  The Tech report TR1091 is available here:

  http://en.community.Dell.com/TechCenter/Extras/m/white_papers/20434601/download

  Changes for Windows and the knots of ESXi virtual machines will require a reboot to take effect.

  What version of firmware you are at, and what version you are migrating towards?

  Other things I always propose updates is to ensure that both controllers are plugged in your switch and in the VLAN correct.  Since assets CM are failed over to the passive, support gets much advertising is unable to access the storage after firmware update.  Or ports of the day before were not in the VLAN correct, or individuals with disabilities, etc...

  It is for these reasons that personally I prefer to do the updates via the serial port CLI.   The process is more talkative, and if something should go wrong, you need the serial port of some sort.   Since the installation and tested in advance is a huge time saver.   Here, we use serial mux so that all array controllers are easily accessible.

  Kind regards

  Don

• Need help of the correct SAS 2.5 upgrade option "HDD for PowerEdge T620

  I want to add the disk to an existing Dell PowerEdge T620 (service tag GTPKDV1) storage. The vehicle currently has 7 300 GB SAS 2.5 "hot, two virtual drives (300 GB RAID1) and RAID5 1116 GB replaceable drives. There are 16 bays.

  Browsing the Dell store for server upgrade parts I am surprised not to see that two form factors for of 2.5 "10K rpm SAS drives. only 300 or 900 GB. Nothing to do with higher speeds or more capacity! And I'm not even sure, one of the search results is really 2.5 "because the Web site product description does not indicate the size at all.

  300 GB of the manufacturer: 15NM6 | Dell reference: 342-2016 (accessories.dell.com/.../productdetail.aspx

  900 GB of the manufacturer: TPMWF | Dell reference: 342-4143 (http://accessories.dell.com/sna/products/Hard_Drives_Storage/productdetail.aspx?c=ca&l=en&s=bsd&cs=cabsdt1&sku=342-4143&mfgpid=225343)

  The 900 GB is described as a hybrid drive. What is a drive hybrid? Isn't SAS, SAS?

  There are several results that seem to be variations on the 300 GB 10 K 2.5 "disk SAS6. They are all the same product? Why the different reference numbers?

  The H710p wouldn't even try to use the 300 to rebuild the 1.8 TB drive failure, as the reader will not be perceived as a Hot Spare for this virtual disk. A 300 GB global Hot Spare would be able to rebuild any 300 GB or more small disc. If the Global Hot Spare is a 1.8 to it should rebuild one of these virtual drives.

• BEFSR81 Firmware Upgrade Gone Bad?

  Just putchased a new BEFSR81 router.  Using the installation CD, I got it Setup and works very well.  Then, I went to the support of Linksys and found page a more recent version of the firmware.  My version is 2.51.4.  I downloaded the 2.51.4.6 version and installed. I made sure to choose the version for my model 3.1. He appeared to install OK, because I got the message that it was for the page in 5 seconds.  Now I can't go to the web-based configuration page.  I can ping 192.168.1.1 and get a normal response, but by entering that address in my browser just times out.  I turned off the router and even held the reset for 30 seconds, but don't can't go in the web-based configuration page.

  This router is now watered?  Do I need to send it back?

  Thanks for any help on this.

  Found the answer in this thread:

  http://homecommunity.Cisco.com/T5/wired-routers/failed-firmware-upgrade-bricked-BEFSR41-v4-3/TD-p/25...

  Thanks Wizzard!

• WRT54G v1.0 Firmware upgrade

  I'm trying to update the firmware for a WRT54G v1.0 (I think, it doesn't have a version # on the sticker).  I downloaded the firmware (through a google cache to the linksys support page cuz link is down).  I have unziped the file. I did a hard reset (60.60.60).  Then I connected to my router (admin pass so I don't know the reset worked) went to "system > Firmware update > Upgrade" opened the dialog box.  Then I bowsed to the .bin file found he opened it and clicked on 'Upgrade'... nothing has happened... waited... still nothing, no progress bar, nothing, nada, neah... whats up?

  I can still access the router as usual and ect is just the dialog box upgrade that seems broken.

  So, any ideas?

  PcCowboy (Caleb)

  (Mod Note: edited post for the respect of the directive.) (Thank you!)

  

  Well since no one seems to know the cause of my problem, I guess that ill just go to the site www.dd-wrt.com, they prob help and they clam to get the best results in their firmware.

  Ta - your.

  PcCowboy

• 200 d IOmega IX4 Firmware upgrade failure

  Hello

  I have an IX4 - 200 d which I inherited. Initially, it wouldn't boot and display only the symbols of USB stick/network after about 60 seconds.

  With some searching on Google, I created a boot disk USB with the firmware updated on this issue. All goes well until the Firmware upgrade begins. I go to the step of (what I assume is) the upgrade of the firmware and it gets 75%, hold for 5 seconds and then the machine stops.

  I tried to repeat the update of the firmware with all the drives present, with every other drive in the first slot and with all the disconnected drives. But it seems to behave in the same way.

  Is this a known issue? Or could it be a hardware failure?

  I'm pretty eager to find a solution - it takes a long time for me to accept defeat.

  The only other suggestion that suggested Dr. Google is to start linux and reformat the hard drive?

  Any help is appreciated.

  Kind regards

  Pete

  Hi André,.

  This case can be closed.

  After the above mentioned procedure eventually work, I didn't know that - ALL readers should be present and formatted during an attempt of USB firmware update / install.

  The link again on the forum - http://forum.nas-central.org/viewtopic.php?f=14&t=4401

  This seems to be the only solution.

  Kind regards

  Pete