Thermal Pad thickness, brand and Type of GPU memory (surrounds the GPU chip) iMac late 2009?

Similar Questions

• I would like to buy and install a stand-alone version of Lightroom on my iMac. I do not want to join the CC program. The CC is not an option for me. I'm iMac late 2009 user, osx el capitan, installed on a formatted hard drive 1 t, 16 GB of ram with1066 MH

  I would like to buy and install a stand-alone version of Lightroom on my iMac. I do not want to join the CC program. The CC is not an option for me. I'm iMac late 2009 user, osx el capitan, installed on a formatted hard drive 1 t, 16 GB of ram with1066 MHz PC3-8500 DDR3 SDRAM. Everyone uses LR6 on iMac late 2009? anyone has any experience with el capitan and LR6 osx?

  Hi Piotrsta,

  With the last update of Lightroom, most of the problems have been corrected.

  Also, you can read the following article: Lightroom and El Capitan | Mac OS 10.11

  Kind regards

  Tanuj

• Help! How do I just go on a blank page and type a letter with all the settings so that I can dash, Center, etc.

  Ok!  I'm very computer"hostile", so how can I find a document/blank page to type a letter, which has police settings, indentation, "BOLD", centering, etc. and be able to make copies?  Thank you.

  Start | All programs | Accessories | WordPad.

• Satellite A300 and 320 GB of memory on the HARD drive

  My laptop has a capacity of 320 GB of memory, but is divided into two different sections each containing 150 GB.
  My first section is almost complete. It will automatically start just save in the memory following ability?

  Hello

  > will it just automatically start saving in the memory following ability?

  No, it won't. You will receive a message like, low space available on C, but you can move the files/folders to local d manually. Remove the unnecessary stuff from local c

• HDD and dvd are not recognized in the configuration menu, what could be the problem?

  The hard drive and dvd drive are not recognized on the configuration menu for my desktop Pavilion a4316f.  What is a controller failure?  A PCI controller can be used to replace the motherboard controller?

  dhobs,

  Anguish, that the suffering of the faulty motherboard has been aggravated by your actions. Why you decided to perform a restore (which re - formate the disk, erase all your data files (documents, photos, videos to misic,) is really amazing.)

  You had a viable BONE, work and the data store. You he clobbered with recovery. As explained, the 'tattoo' reads the embedded hardware configuration and will stop at the resumption of treatment if it detects a change.

  Only temporary help I can offer is to open the computer case and install a small 12v on the NVidia chip fan. IF the chip is not 100% burned, you can earn low enough time to reinstall the operating system and then add the map.

• VMware Fusion 7 and VMware Tools - leak memory in Debian comments

  At some point during my updates from Mac OS X to Yosemite, VMware Fusion to 7.x and my Debian a guest to 8.0 "Jessie" on my 2012 Mackbook Pro, leaking memory of the Linux kernel is developed.  If I follow these steps, then I'd lose soon about 3 GB memory of the core area.

  1. Install Debian Jessie in a new machine virtual de VMware Fusion
  2. Install open-vm-tools or VMware Tools bundled.
  3. Perform an intensive IO as operation simply cat/dev/zero |-c 1000000000 head >/tmp/test.txt.
  4. Smem - wtk and see ~ 3 GB memory under the dynamics of the kernel memory, benefit.

  I opened the 15709682007 assistance request and the representative said that they will fix the problem in a future release. In the meantime, I have what seems to be a workaround for someone else that is affected.  Basically, pulling packages from backports jessie seems to have solved the problem.  This is based on the comments added to open-vm-tools.

  1. Add the Debian repository -backports jessie in /etc/apt/sources.list
  2. sudo apt - get update; sudo apt - get install t Jessie-backports open-vm-tools-dkms open-vm-Tools-Office
  3. sudo apt - get - t jessie-backports dist-upgrade (install kernel 4.1)
  4. Restart comments

  A few quick thoughts:

  1. If you have several virtual machines (or other programs) running on your computer host and VMware Fusion detects that there is memory pressure on your host computer, it uses the "balloon" (vmw_balloon for the latest distributions of Linux) Guest pilot to fly some memory of the guest OS.  This memory "stolen" would appear as memory Dynamics non-cache kernel inside the guest.  Running "sudo rmmod vmw_balloon" should release all memory climbed to the guest OS.  Note that using the balloon driver generally improves the performance of the guest and host, despite the appearance of fear "used memory" inside the guest-"used memory" is just a thing of accounting that we had to use in order to change the priority of the memory between the host and the guest.  It is not "used" in the conventional sense of the term.

  2. I believe that recent versions of virtual hardware non-cache dynamic kernel allocate the necessary memory for SVGA and 3D features (display RAM, texture RAM, etc.).  Disable graphic 3D acceleration or by reducing the amount of graphics shared memory if you are using a new version of virtual hardware (both in the VM > settings... > display) might help.  Decommissioning of a virtual equipment as early (in the VM > settings... > compatibility) can also help.

  See you soon,.

  --

  Darius

• Pavilion dv7t 6100 - LM726AV: replacement of heat-sink/fan using the thermal pads and thermal paste/paste

  Hello

  The fan on my laptop died so I am trying to replace the fan and the heatsink unit. The manual that I use specifies that thermal grease should be used on the cpu and heat pads must be used on the graphics processor and the capacitors.

  The arrival of the new fan it came with heat pads on all relevant areas of the sink as a tube of thermal grease. When I removed the old fan, thermal pads have proved only on the capacitors and the components around the GPU and that thermal grease was used on the CPU and the GPU.

  My question is: how this part must be installed? Should I remove the fron pads thermal heat sink that covers the processor cpu and graphics and do not use the thermal grease in these areas? Or the thermal grease can be used here and let the thermal pads on the heat sink?

  Thanks for your help - thank you for the advice/opinions in this case.

  You can remove the protections and pass with the dough so but only f, you are sure that the metal on the core processor and graphic is in solid contact. And there, I meant it touches and also has a lower compression. For me, the thermal paste is superior coolant and should be used on really hot spots. However, if the metal is not full, solid contact you run the risk of overheating.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Recommendations for a good cleaner liquid screen and type/brand of cleaning rags?

  Recommendations for a good cleaner liquid screen and type/brand of cleaning rags?

  Or are the wipes of alcohol okay? (Like what you get in a closed container and pass through a hole on top)?

  The safest method of cleaning of the screen is to use a thin rag (glasses cleaning cloth) moistened with distilled water.  NO ALCOHOL.

  I used successfully:

  http://www.Windex.com/en-us/products/pages/electronic-cleaner-and-wipes.aspx

  Ciao.

• 1245dx D7 - reapply the thermal grease for CPU/GPU - GPU thermal pad

  The result is a hp pavilion dv7 1245dx having heating issues so disassabled to clean it and apply new thermal grease and notice that the video chip has a thermal pad instead of thermal grease. This is what it looks like.

  Guys/girls do you think it is reusable or do I need to replace it as well. If I need to replace it, what are my options? Difficult to find a pad thermal repalcement anywhere. A decent high CoolerMaster performace size heat for the CPU it's okay.

  Yes, it uses a thermal buffer, because the gap is too big to fill with dough. You can reuse the pad. Some people even make a solid metal shim in sheet copper or a hammered out penny and you can apply heat is dedicated to that.

• Thermal paste or thermal Pad?

  Hi I have a M17x which came with two Nvidia Geforce GTX 280 m SLI graphics cards, as I can switch between hybrid and discrete graphics modes I believe is the saying,

  It also has the third on board graphic chip Nvidia Geforce 9400, which is where my question in fact because this chip shares the same radiator as well cpu I upgraded the processor is a few days and doing so re thermaled the cpu but the Geforce 9400 looked like originally, he was given a bottle and not glued?

  So I left as is and re - apply the heatsink on the cpu and 9400 each chip has 4 screws around the cpu & gpu lock and hope for the best.

  But since I kept an eye on the time and the Nvidia Geforce 9400 that i never, I always use SLI with the 280 has seen some time whereas this is not used and every other chip is always at least 20 degrees colder I saw between 60 81 deg while everything else is way lower so that I have to buy thermal pads and use a sub it or can I use the same dough I used on my cpu because it must be the problem, Yes?

  Hello

  We recommend that you use a heat mat or use the same dough, either option should help to lower temperatures. Temperatures are high for this type of video card, especially if you don't use it yet.

• whenever I use my laptop and my palms are based on the laptop and I type all of a sudden... my guard resize bigger or smaller screen size

  I try to keep my thumb on the mouse pad Palms when I type, but every now and then my screen resizes more or less until I take my left the base of keyboard sound Palm only when my left hand rests on the base next to the touchpad. I type pretty fast so it becomes boring and yes she also jumps screens or go back to the previous message and I choose ctrl z to cancel and return to my message I was typing... It also switches tabs on me too... don't know why my Palm being to the left of the keyboard on the basis should effect other thing he does after a while. and I have to stop what I'm doing... and go to the firefox menu and change the size of the screen down to 100%, sometimes she's going up to 200-300 other times it comes down to 70-80%, I find this annoying I I wish there was a way to disable the resizing of the screen in the control panel. If it's just to be 100% happy with it I'm I have need it larger or smaller... There should be a way to LOCK... I understand that there are people out there with eye disorders and needs to have the screen size increase by using the + or - but there should be blocked so there's just no matter what is happening on my keyboard or the touchpad or the basis of the cushion... this screen size not will increase or decrease. unless I turn off the lock... maybe this is something that they can be implemented in the next version or do a quick update of the browser

  Maybe a support forum for this laptop brand will have some ideas, because that is not strictly a problem with Firefox only.

• Question about the thermal pads

  Hello, I have a question, is what heat pad should I use heat pads HP service guide for my graphics chip, this is what it says and how do I use them

  "The thermal pads are used on the Northbridge contact (3) and chip Northbridge (4), chart/heat sink contact (5) and chip subsystem (6) graph and chart/heat sink contact (7) and capacitors (8).

  http://h10032.www1.HP.com/CTG/manual/c02666747.PDF

  The question is, what thermal pad use? Because I have a 0, 5mm thick, another of 1 mm and another 2 mm, and I don't know which one I need

  Look at the picture on page 96 of the Manual:

  Manual

  Each chip that needs a thermal buffer is a different size and shape. Are the keys that you have replacements or you reuse the original? They are different sizes and shapes, apart from the thickness? Otherwise, I would bolt the heater without heat is dedicated to the as a dry and watch the free space on each chip. It should be obvious which cooling pads on the heat sink are closest chips on the motherboard and organize them accordingly. The pads should be compressed a little when screw you the radiator.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• ZD8000 thermal Pads

  I made the mistake of taking off the heat for the GPU and Chipset pads when I went to apply new thermal paste to the CPU. The thermal paste on the CPU is fine but not, I get artifacts and heat ups when I play games because of the keys. I reapplied the pads but I'm afraid I've damaged one of the keys.

  Is there anywhere I can get the original for the gpu and chipset pads? Also they felt a bit greasy when I removed, HP use the thermal grease on top a thermal buffer? If Yes this is weird lol.

  If I can't get the originals anyone has a recommendation indicating where I can get a few buffers that will do anything as well?

  Although it was a solution, however is not a good thing. After dealing with heat from take the pads off I decided to buy another radiator with the pads on them.

  Now, everything is very fine and back to normal. I suggest to everyone to never take these. They seem to be of good quality for a thermal buffer and dissipate heat much better than the thermal paste.

• Thin Oracle and Type 4 driver: Dummy Question

  Sorry, this must be a dummy question, but...
  
  I just read "JDBC driver Type 4 Oracle has been deprecated" in WLS11g.
  
  I always thought that the Oracle thin driver is a type 4 (java only) pilot, then I would be really grateful to get this right classification.
  
  It must be FAQ, if all the references that a response is fine.
  
  Thank you
  
  b.

  There are two drivers of type 4 (all-java) in discussion. One is a weblogic brand
  one, who is currently deprecated. The other is the Oracle thin driver, which will be
  the favorite driver to proceed for Oracle. And note that the 'thin' driver is really
  "thin/type-4' or ' thick/type-2', depending on which way the URL is given."
  If in the OIC, it is type-2, using / installing the Oracle client and the
  Libraries of the OIC in path of load_library in the process of the JAVA virtual machine...

• SSDS must be similar in size and type to raid 0?

  SSDS must be similar in size and type to raid 0?  I have a 2009 MBP 2.66 bicoeur.  SSDS are an old sata 250 GB Samsung 850 pro III and an all new Intel 160 GB (320 series) sata II.  The hard drive on the MBP interface is 3.0 GB/s sata optical drive interface is 3.0 Gbit/s

  Different size, different brand, sata II issue III v?

  If it works, it will be almost double the read and write rates, I understand.  I am aware of the increased risk of data loss.  Will only use for backup data.

  How is it difficult to set up raid 0?  I don't know the first thing about raid 0, 1, 2, 3?

  Thank you

  Stu

  If it works, it will be almost double the read and write rates, I understand.

  RAID offers for the SECOND and the following read/write of the same LARGE file acceleration and not otherwise. Any intervention of reading or writing in different files eliminates the acceleration. Any acceleration is much more dramatic on rotating discs, because it can eliminate some of the 10 ms or more long 'dead time' while the reader is a new track and the controller must wait for the correct data go in the position under the read/write head. Acceleration on the low-latency SSDS is far less dramatic.

  The system drive / boot is particularly bad choice for a RAID, it reads and writes small random files in all directions. Who will get no acceleration.

  You can best be served by creating a workflow that allows separate readers for the source files to Destination files, files of zero and drive system / boot.

  --------

  RAID is usually done on the disks that are exactly or nearly the same. Too slow response of one of the discs can cause the RAID failure.

  RAID support has been removed the disc utility GUI in 10.11 ElCapitan, probably because too many casual users got into trouble with the built-in GUI functions. You need to use the diskutil command in the Terminal, or buy the SoftRAID(4) package.