Thickness of line 3D plot

Similar Questions

• Satellite Pro A10 - 3mm thickness vertical line on screen

  I have a thick vertical line of 3mm on the screen seems to come up in colors, it generally moved to gray.

  The display was damaged - or is this some sort of driver problem.

  Hello

  It looks like a hardware malfunction. UPS may be a FL. But I m not 100% sure.
  What you can do? Well, if it's really a hardware fault so the only way is to contact Toshiba service. But it could also be a strange software problem. In this case, the best way is to recover the operating system and/or update the graphics driver. You can also check your BIOS version. If there is a newer version, then try to upgrade the version of the BIOS.
  But if the material is broken, then contact ASP.

• Incoming Fax page, left thick black line down the side edge

  Hello

  I recently bought a HP Photosmart 7520 printer and had to return because of a wrong switch ON / OFF the printer.  So I returned and bought another. This second printer works perfectly so far!  However, when I recieive a fax, the page has a very thick Black Line crosses the length (less than an inch from top and down) on the left edge. It almost seems to be a template for a fax page?  The first printer (a returned) did not do that, but it does not appear on the second printer.  In addition, the original page fax I sent to my friend and he said, that it doesn't have a thick black line on the fax page, he gets... and then he sent me along a return fax with this black line appears.

  Comment of thoughts,

  SyBerGuy

  Hello

  For more than a week since my last post. And I also had the printer connected to an outlet of power strip surge protector (never needed to connect directly to a wall, which I would have if I had a problem).  The problem has been resolved by replacing the large black ink cartridge, which was not printing text.

  In addition, earlier when I check the ink level, he showed the graphics still about 1/4 rest in the cartridge. I had also previously clicked on tell me when the ink level is low. None of this happened?  So now I have to watch closely what is printing a page of text clean/good.

  So for now, the printer is good to go and I hope not to have more problems... thank you for your help!

  Sy

• Export of sovereign wealth funds, get the thickness of line precise CS5

  Hello indesigners,.

  I recently tried to create a CV interactive little, nothing complicated, just an index page which links to the chapters.

  In the identity document, I use lines with very little wight (0.25 pt or 0.25px, depending on the print mode or the web). When I export to a SWF file the lines are always much thicker than they really are. It seems that the minimum thickness, it can show is perhaps, 1px, while ID can show more fine lines (do not know how it does, maybe anti aliasing?).

  I can remedy that and export it in the form of raster image, but then, it removes any interactivity.

  I just want to keep the items in the vector reduced to their actual thickness, does anyone know how to do this?

  I've attached a picture that she shows off quite well.

  http://DL.dropbox.com/u/25033198/Untitled-1.jpg

  Ah, Yes, of course for this. I forgot to treat the "fix" you found.

  It is a 'fix' rather than a real problem, because if you zoom in on this image, you'll see that it contains no pixel 1/4 more! The image renders too thin lines identical to InDesign: as light gray.

  There is progress and disadvances to save the image as a bitmap, rather than as a vector; I think that you are aware of both, and it is up to you to decide which method to use.

  If you are sure that your users (consider that they will look at what on paper) will not zoom in, you could still use the lines of 1 point but their light gray color, so the Visual effect is the same 100%. And it will look only slightly weird when your users zoom in - they will get * thick gray * lines, instead of * thin black * those, but it's still better than ugly pixels.

• How to get the snap-in to examine the thickness of line?

  This is a pet peeve for a long time that I have with Illustrator and may all of you have some tips to achieve this (plug-in/script/technical)?

  When using the bearings commented and serpentine, trigger correctly two objects together according to their paths when plotted mode:

  (A line of track and a vascular non-accident brain, but filled square)

  

  But when I pass in preview mode, visually it's incorrect since the snap is not taking into account the thickness of the line line.

  

  Another that the use of contour line (which has practically destroyed the possibility of editing the race later), is there a way to get the alignment in order to study the thickness of the line? (I understand as I could caress the place the same amount on line, but I can't do that for this particular work)

  Choose use limits seen in the Panel menu align and then use the Panel align to align them, rather than smart guides.

• Binding of WPF graphics and definition lines and plots only in the ViewModel

  Hello

  is it possible to bind all the Axes and all parcels in the Viewmodel?

  Now I've set the Axes and the plots in Xaml, but I want to generate momentum. Is this possible via the ViewModel?

  My graph now looks like this:

  My ViewModel looks like aktually like this:

  public ChartCollection[] chartCollection { get; set; }
  
     chartCollection = new[] {
          new ChartCollection(1000),
          new ChartCollection(1000),
            new ChartCollection(1000),
          new ChartCollection(1000),
                   new ChartCollection(1000),
          new ChartCollection(1000),
                   new ChartCollection(1000),
          new ChartCollection(1000)
      }; 
  
  and data-insert :
    test = hw.T_a1Actual.ToString();
      chartCollection[0].Append(hw.T_a1Actual);
      chartCollection[1].Append(hw.T_a2Actual);
      chartCollection[2].Append(hw.n_a1Actual);
      chartCollection[3].Append(hw.n_a2Actual);
  
  }));
  

  But I want to generate all the Axes and all dynamic plots. What is the best way to do it?

  I can do this via the ViewModel?

  Thanks in advance

  Manual

  Do not forget that the plots and the scales on a graph are just components and not the user interface objects themselves.

  It would be possible, with little code, take a set of models 'conspiracy' and 'axis' models and generate plots and lines of them, which could then be synchronized with a graphic. If expose you the Plot and AxisDouble components on the model, then the synchronization code would be necessary:

  public static class GraphExtensions {

  // Private property to hold on to synchronizer.
        private static readonly DependencyProperty PlotsSynchronizerProperty =
            DependencyProperty.RegisterAttached(
                "PlotsSynchronizer", typeof( CollectionViewSynchronizer ), typeof( GraphExtensions ) );

  // Public property to declare source of Graph.Plots collection.
        public static readonly DependencyProperty PlotsSourceProperty =
            DependencyProperty.RegisterAttached(
                "PlotsSource", typeof( IEnumerable ), typeof( GraphExtensions ),
                new PropertyMetadata( OnPlotsSourceChanged ) );

  public static IEnumerable GetPlotsSource( Graph g ) {
            return (IEnumerable)g.GetValue( PlotsSourceProperty );
        }

  public static void SetPlotsSource( Graph g, IEnumerable value ) {
            g.SetValue( PlotsSourceProperty, value );
        }

  private static void OnPlotsSourceChanged( DependencyObject d, DependencyPropertyChangedEventArgs e ) {
            var graph = (Graph)d;

  // Retrieve existing synchronizer, or create a new one for the target graph.
            var synchronizer = (CollectionViewSynchronizer)graph.GetValue( PlotsSynchronizerProperty );
            if( synchronizer == null ) {
                synchronizer = new CollectionViewSynchronizer { TargetCollection = graph.Plots };
                graph.SetValue( PlotsSynchronizerProperty, synchronizer );
            }

  // Synchronize graph's plots with new source.
            synchronizer.SourceCollection = CollectionViewSource.GetDefaultView( e.NewValue );
        }
    }

  In XAML, you can set the property attached on the chart as:
      
  : where the model exposes a collection or the observable collection of Plot objects.

  A similar attached property might be set to synchronize the Axes collection on a graph with a collection of model.

• Adding a double layer of a line drawing makes lines look more dark / thickest. The more layers, the thicker the lines themselves.

  I draw the picture of drawing line type "Cartoon", with a size of pressure brush hard. When I duplicate the layer to place over it, the lines appear darker and thicker. The more times I copy the layer, thick lines get. (See pictures attached). until finally almost all of the white in the hair of the woman disappeared.
  The layer is brush only, on a white background which is on its own layer.

  The opacity of the layer is 100% brush opacity is 100%.

  Layers are set to normal.

  I have reset my preferences, and I have the reset tool.

  I paint with a Wacom Intuos Pro and also deleted / reinstalled the drivers for it, so reset the service.

  So, how to stop this?

  I need to duplicate these layers and keep them looking for the same thing, that the final product (an animation videoscribe) needs adding progressive layers to the image that I added in the different elements. (Ps has not always done this... it has been progressively worse... it used to work very well.)

  Please let me know if you need more info, I joined as a lot of images that I think would help.

  

  

  

  whenever you draw no straight lines... Photoshop, it's what we call 'smoothing' it creates intermediate pixels in order to avoid the cut edges

  you, the layers are Transparent

  one way to avoid this:

  to add a white background below each layer and group them, then duplicate the Group

  Another way,

  Duplicate the layer and set the difference blending mode

• Thick border line between two columns

  Hello all;
  
  I have a requirement where the user must be able to distinguish between two columns hnce asking a thick line, rather than the usual 'by default'.
  
  Everything is 'Default' until then.
  I clicked on properties of the 1st column and in the section "Border", I chose "Custom" and made the right wall of the cell in black color.
  I see a thick border now, but it has eliminated the 'default' border separating lines. His party make the entire column look like a single cell.
  
  I don't want any change with the exception only of the border of a column of a black line.
  
  Any help is greately appreciated.
  
  Thank you!

  The column properties-> Options of Style CSS custom (HTML only)-> use custom CSS Style->
  the following CSS code
  border-right-width: 1px; border-right-color: green;

  or go with someone with the necessary changes

  Appreciate if you score as correct if it works

  Published by: Srini VIEREN on December 11, 2012 16:43

• Thickness of line - my mouse or my digital pen is able to 'wake up' (to settle) the field of line weight. He's stuck on 0 pt.

  InDesign CS4 version - Have not used the product for a few years. Recently purchased a Wacom Cintiq 27 "and equipment upgraded to accommodate (GE Force 950 graphics card, processor I-7, RAM increased to 16 MG, two monitors [which is the digital Wacom pad] are fixed to a HD 2 X resolution). These are the only changes since last using InDesign.

  Have reinstalled InDesign completely after running into trouble looking for updates (said me the update was already running in the background which does not seem to be true).

  In any case, impossible to use program so I can't access the line weight.

  Advice/feedback would be highly appreciated.

  Thank you

  'Micheloise '.

  https://helpx.Adobe.com/InDesign/KB/InDesign-tools-panels-Don ' t - respond.html

• The thick, horizontal lines appear in source and program Viewer footage set to less than 100%...

  Can anyone help?

  This suddenly started across all projects, including those that I worked on for centuries without any problem.  Everything else seems to be exactly the same in other applications than ever before, PP only is affected.  The film is all progressive (I rarely encounter interlaced nowadays), prores HQ 25 fps, usually 1080, but also 720.  Output to the screen, through MXO2 mini is fine and has not changed at all.  I can't think of updates recently, certainly not in the last week, when it started.

  It's really weird and obviously wrong, but I can't begin to find how to solve this problem, after exhausting all my standard corrections (settings in the application hardware, OS, etc. all checked and rechecked.  Made restarts - without result).

  My system is:

  MacPro 5.1 6 hearts 3.33 GHz

  12 GB OF RAM

  GTX285 Mac GPU - CUDA 5.0.45, GPU driver 1.3.4.0 (295.00.05f03)

  OSX 10.7.5

  PP CS 6.0.2

  MXO2 mini - latest drivers etc.

  All thoughts, much appreciated!

  Thank you

  Dominic

  Well, I think I have fixed it but any the wiser for why I got this problem.

  Fixed by upgrading my OS to OSX 10.8.3 (always experience trembling nerve), after my startup etc. disk cloning.  Then I updated to the latest CUDA, reinstalled my Matrox drivers and crossed my fingers!  Fortunately, everything seems fine now.  I can only think that the problem was, perhaps, something to do with CUDA, because the only time where I never had a problem has been using PP and reading less than 100% scale.

• 5610 all-in-one - black thick top of line down on the pages scanned using the scan feeder tray ONLY

  Using HP Officejet 5610 all-in-one I've had for years and maybe 6 months ago, I noticed that anything that is analyzed by the load plate (if you need to scan a bunch of pages without having to analyze each page individually between analyses what is tedious that need constant attention) has this thick black line goes up and down on the middle left of THE pages scanned. Honestly, it looks really bad like if there is something hidden in this terrible line through the process of moving the paper through the feeder, BUT the original is just fine without damage.

  If I scan just a page by placing the document on the scanner glass, and then NO matter whatsoever.

  100% reproducible every time.

  So I know that it has nothing to do with the glass (which is clean), but only when the scanned document must pass through.

  Checked the forums for similar problem and found no exact match.

  I imagine that an expert out there knows the answer to that high hand. IF you could speak up, I would appreciate it.

  I THOUGHT ABOUT IT!

  I read another post:

  http://h30434.www3.HP.com/T5/scanning-faxing-and-copying/HP-OfficeJet-Pro-8500A-plus-vertical-black-lines-only-when/m-p/1391261/highlight/true#M30268

  who is mentioned on opening the ADF cover. Well I opened the whole Assembly, having absolutely NO idea how it all works, and I found a 1 "x 8.5" thick mirror (for lack of a better term) who had what looked like white paint on it to the place where the pages were probably getting the black line. I scratched, retested and the question was gonzo - that's all!

  Then my wife just told me that she thinks that she knew what the problem was all along. She had put on a page and it had not dried, and she tried to put it in the charger to make a copy. She just thought that we were going to replace the printer even when and if ever, let me know. During this time it was me mad for months. What are you laughing at me? This all-in-one works very well for years - replace without good reason, must learn a new product, get new cartridges, out the same old, same old, NO way. If it is not broke, do not replace it!

  Detective Conan.

• Green and blue flickering thick vertical and horizontal line with windows media player

  Original title: green and blue flashing

  Windows Vista

  Windows Media Player
  I have a problem with windows media player. I have a green and a blue flashing thick vertical line. And also a green line below horizontal. Why?
  Help!

  Hi bjorn81,

  1. when exactly you get these lines?

  2. This occurs when you try to play videos?

  3. If so, what is the type of file you are trying to play in Windows Media Player?

  4. What is happening with all the video files or a particular video file?

  If the problem affects all or most of the video files you play (as opposed to a few specific files), the software of the driver for your video card (also known as a graphics card, video, graphics card or graphics card) may be outdated.

  Play an audio or video file: frequently asked questions - what can I do about video problems, such as green or pink lines appearing in the flickering or choppy video, the player will stop responding during video playback and so on?

  http://Windows.Microsoft.com/en-us/Windows-Vista/play-an-audio-or-video-file-frequently-asked-questions

  Also check out the link:

  Updated a hardware driver that is not working properly

  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

  Hope this information helps.

• Can I disable pressure sensitivity? -from the pen of apple. Want the lines to be of the same thickness

  can I disable pressure sensitivity - using pen to apple? Want the lines to be all even thickness of line

  Hi Samara.

  This feature is not yet to the draw. But it is coming... In the next update.

  Hang in there.

  Sue.

• thickness of the line continues to change when im painting

  When I paint brush tool keeps blurting from time to time with a thick black line. Really boring.

  Ok.  So I assume you are using the Wacom driver 6.3.13 - w3 ?  The problem of inconsistent line was mainly associated with the Cinitqs if the memories are good, but I wonder if Windows 10 has complicated matters.

  Yes, there is a long thread length on the site of Photoshop feedback and a very recent addition referring to Windows 10, but I'm not recognizing driver versions that he mentions.

  Photoshop: CS6 Brush tool - pressure sensitivity sometimes fails to race to race

  If you are unable to address this issue of play with the drivers, try the Lazy Nezumi Protrial version.  It's actually a must for any user of Tablet IMO, and it fixes many problems of drawing as it is the main function to help you produce smooth flowing lines.

  

• Change the thickness of the line on the grouped objects?

  If I change my style of animation art drawn by hand to the use of things such as the line tool and pen, in Adobe Flash CS3. I paint characters who have segmented parts, I.e. the arms, legs, head. body, ect are all separate grouped objects with a set line thickness. The problem is that when I try to reduce or to develop the character, the lines that make up their body is too thick or too thin, depending on whether I'm bigger or smaller. It seems that I'm unable to change the line weight of the grouped objects, or dare I say, a Group of grouped objects. The greys out properties panel when I select an object, so I have no access at all. I don't want to go and change the thickness of line individually on each object, whose lines are all the same thickness originally.

  Is there a trick or a plugin that I can use to change this, so the line weight of the grouped objects can be changed? Or am I just ignorant the right answer with myself? Whatever it is, I'd be REALLY grateful help could someone of you provide!

  Okay, so I seem to have found a solution more effective in my problem what I expected. I can just convert the lines into filling by going to edit > forms > convert the packaging lines. That makes it so the lines will now change of relative size depending on how much I shrink or push an object.

  Please try to all the world, but I found my solution!