Time missing ligatures in FF9

Similar Questions

• DSLRA200 10 sec self-timer missing

  OK, so basically the second 10 self timing drive mode is missing. There are 2 second one, but it is not very useful for the moment. Someone has the same problem or have any advice for me? Thank you

  Hello
  Welcome to the Forums of Discussion of the user.

  Default value for the self-timer is 2 seconds. This is used when you use a tripod to avoid shaking so the camera will take the picture without you touching the body of the camera.

  Follow the guide on page 90 to 10 seconds.
  http://www.docs.Sony.com/release/DSLRA200.PDF

• Event time missing in iCalendar El captain

  Since the upgrade to El Cap", apparently I have more option of > iCal Preferences > General > Show events time.

  Is there a work around for the time of the event see according to iCal monthly?

  All entries received with gratitude - thanks in advance

  JWA,

  Have you tried to expand the window to display the month?

  

• Control Panel date/time missing HP 7510 in settings

  I can't locate date/time for the HP 7510 settings.  Research on the Web suggest that this is an option under the icon key, then Preferences.   I looked and the date/time option is missiong.  Any ideas?  Thank you!

  Hello

  On HP 7510 located under the option date and time

  Menu (wheel) configuration > tools > Date and time

• Satellite M100: BIOS time is incorrect

  I have a Satellite M100. Yesterday when I turned on my laptop clock sets time in 2010. After that I put the time, missing a few minutes or I went back an hour in 1-2 hours after that I have to reset the time.

  I checked the time window with BIOS using promt, but it's the same thing. I put DST correctly and because I'm using my United network it may be restrictions for me to synchronize the clock. I am using windows XP home.

  Please help suggest what I should do to stop my clock acting wierdly?

  Thank you...

  Hello

  I put t know if this will help, but please don't forget the battery CMOS is not empty. See s operating manuals and you'll find info, how long battery CMOS must be fully charged.

  If you are in permanent line be as safe as the time of the laptop will be permanent synchronize with internet time server. This option, you can find in the properties of Date and time.

  Good bye

• Real time

  Hello world

  I write here because I have a problem using a controller real-time (OR 3100 RT) in my application.

  The controller is used to send a TCP/IP packet to a Robot SCARA controller that needs to receive an update every 8ms (this is the reason why I used the RT controller) and read the package of the robot. A PC is connected by a cable ethernet on the RT controller, so that the user can select the final position, speed, etc. and view the position of the controller and the values some of load cells.

  If the PC and the RT controller share a few global variables (final-effector position, the value of the normal force,...).

  The application works very well. The problem is that, after a few minutes, the RT controller loses connection with the robot and the robot, I get the error message related to a package delayed; so I guess that the VI had some problem to send the update of position to 8 ms.

  If I run just the VI on the RT controller, without launching the VI on the host PC, everything works fine. When the RT communicates with the PC, I get the error of timing.

  What can I do to fix this? In the RT vi controller I made two loops, a high priority one, to send packets to the robot and a low priority for communication with the PC, but the problem is still there. I also tried to change the settings associated to the timed loop (timeout, take time, missed periods, maintain the phases initial), but no good result (but if I uncheck the 'Discard without rules', the problem occurs less frequently).

  I have attached a few screenshots related to the target.vi, in particular the options related to the synchronization of the two loops, and how I implemented the loop of low priority.

  Another question: are there options in the global variables section that can help me solve the problem?

  Any suggestions would be great,

  Thank you very much to all the world.

  Carmine

  
  

• Satellite P500-12F - mouse trackpad not working not

  Hi all

  I just bought a P500 opportunity and the touch pad does not work, I tried to market through f9 FN keys but nothing will work even the left and right mouse buttons, I would like to ask if there is something else I can try or if not what kind of costs are involved to fix it please also where would I get a backlit KB and it would work on this model? When I type some time missing a letter as if I'm not hitting the keys hard enough, but I think I am lol...

  Any help really appreciated, thank you very much.

  Sincerely, Wayne...

  Hi CT1965,

  The touchpad does appear in Device Manager correctly and did you test if other FN keys work correctly?
  What operating system is currently installed?

  There are different reasons why the touchpad does not work, but first of all I recommend reinstalling the driver for the touchpad itself. You can download it from the official European driver Toshiba download page.

  Regarding the backlight keyboard: it s based on the motherboard if there is a second keyboard to the keyboard backlight connector. Normally, you can check this if you disassemble the laptop and remove the keyboard and take a look at the motherboard, but if you are not familiar with the disassembly of the laptop I would ask a maintainer approved assistance. :)

• Samsung note3 does not ring when you receive a call

  The new version of Skype is bad. My operating system is 4.4.2 kit kat almost 100% of the time Miss l name because it does not ring. When I make a call and do it on the loudspeaker, it just for no reason rebascule on the speaker internal and if I'm on the blue tooth, it stops working on the blue tooth and I have to switch between the external speaker and back to the tooth of blues to hear it again which is very dangerous for driving. It also only connects to the blue tooth after 2 or 3 trys, entering my prius that this only happens with Skype if I use the t-mobile application that it works every time perfectly with everything l am reports that I have a Skype number and a number of t-mobile

  I have 2 samsung note 3 with the same software 4.4.2 kit kat, I have the latest version of Skype on 1 of the 3 note, and the other has the older version of Skype when a call comes in only one with older version rings.
  
  every now and then a new will work perhaps less than 1% of the time.
  
  There are many other people who have this problem. I wish that they would at least recognize that they have a problem!

• PXI64HANG

  NEITHER posted the following warnings earlier this year, but has not provided details about the symptoms of this block.

  Possible system block with the third-party PXI Modules for some of PXI systems OR a 64-bit operating system

  http://digital.NI.com/public.nsf/WebSearch/85A51FFABE5C17F886257995001AF369?OpenDocument&submitted&&...

  Notification of product: System Possible crash with the third-party PXI Modules

  http://digital.NI.com/manuals.nsf/WebSearch/6C2BC403421708B5862579BF006E2D0B

  This would produce a warning in LabVIEW, a pop-up window or a system crash? This error may occur in the background or only during the communication of the instrument? This would cause other LabVIEW, TestStand to hang or just PXI communication processes?

  I don't want to take production systems down to an upgrade of the driver if it is not necessary. So I have the record of someone who has experienced this problem at first hand.

  Thank you!!!

  Sam Broyles

  Test Engineer

  INOVA geophysical

  Sam,

  If you start this problem, it is not subtle.  It will stop what communication whether in the PXI chassis, including bluescreens or crashes the system (assuming that you use something in the chassis).  It occurs whenever there is a 64-bit address bus, but when that happens, you will have a hard time missing.

  -Robert

• Text in blue the occultation in officejet 6310

  I was pulling my hair out trying to fix a problem printing with text fonts.  My Officejet 6310 wants to print a pale blue shadow under the text in bold .  Doesn't seem to matter where I... internet print or word document.  I checked all the font settings, unplugged my printer several times missed the doctor print and nothing seems to help.  I played around with settings of 'high quality' and that didn't seem to help.  I noticed when I print photos of ancestry.com, they seem a bit fuzzy too so I don't know if it is a problem of color cartridge.

  It seems to show a text light blue shade.

  The only work-around, I was able to fix with it's choose the preference for "black ink only" in the color management.

  I only use HP inks.  I have Windows 7 and my HP 6310 Officjet is not that old.

  Any advice would be appreciated.

  I have to keep that in mind if I continue to have a problem.   However; It seems to be a color ink cartridge problem!  I removed the cartridges and cleaned the area of conection with a q.  But... I noticed my colour cartridge was very dirty and it took me 6 Qtips to remove any ink from the outside, so I think it was oozing too much ink and interfering with the print quality.  Once reinserted, it seemed to print correctly.  OUCH... took me 6 days to discover it!  Because the cartridge is relatively new, I have it has not verified and have not run the cleaning function.  Cleaning by hand, it was certainly necessary, because this cartridge was terrible!  Thank you so much for coming back with me so fast!

• Stuck trying to install vista OEM on HP Pavilion with motherboard replaced

  Hello

  I have a HP Pavilion with Vista pre-installed OEM. The machine is out of warranty HP and it was purchased while I lived in the United States. I am now back home in the United Kingdom. In any case, the motherboard is dead (common fault on the model of machine, I got) so I replaced and got Vista working again by using the product key that is stuck to the case. Vista then I messed up with a virus and so I trashed it and tried to re - install using the rescue partition and backup discs that I created. None of these options do know as changed the motherboard. I now put Linux on the machine and most of the time, Miss me not Vista. However, my son has an Ipod Touch who needs ITunes and used to run Linux. Yes, there was one I can get vista's new media and reinstall vista, and then turn on again? Really, I can't justify buying a new copy of Windows, so I have a valid license and that you need to run ITunes.

  It makes me feel a little cranky. HP are without help, beyond their warranty period.

  See you soon.

  http://welcome.HP.com/country/us/en/contact_us.html

  In this case, because it is only a replacement for any problem with HP Recovery Software/process, contact HP.

  This isn't their recovery process, Microsoft.

  See you soon. Mick Murphy - Microsoft partner

• Problem with CellRenderer

  Hello everyone,

  the File.browse () is currently too bug, I write a small browser in my application itself. All files that can be opened are shown in a list and now I want to display an image based on the file type.

  I currently have this code (based on this thread):

  package renderer
  {
      import flash.filesystem.File;
  
      import qnx.ui.display.Image;
      import qnx.ui.listClasses.CellRenderer;
  
      public class FileBrowserRenderer extends CellRenderer
      {
  
          private var image:Image;
  
          public function FileBrowserRenderer(){
              super();
              image = new Image();
              addChild(this.image);
          }
  
          override protected function draw():void{
              super.draw();
          }
  
          override protected function drawLabel():void{
              super.drawLabel();
              if(this.data){
                  if(this.data.isDirectory){
                      image.setImage("file://" + File.applicationDirectory.nativePath + "/images/folder.png");
                  }
                  else{
                      image.setImage("file://" + File.applicationDirectory.nativePath + "/images/file.png");
                  }
                  image.x = 5;
                  image.y = 10;
              }
              if(this.label){
                  label.x = 40;
              }
          }
      }
  }
  

  The list is set up correctly:

  list.setSkin(renderer.FileBrowserRenderer);
  

  The problem, I have the experience, it's that she sometimes shows icons wrong despite all the variables that have been set up correctly. Mind that this only occurs after the first time. So what I am doing wrong?

  It might be useful to add that I erase the DataProvider whenever the user opens a new folder by using:

  dataProvider.removeAll();
  

  My fault was apparently that I didn't not use embedded images. The loading time missed some things until I guess. This is my code to work:

  package renderer
  {
      import flash.display.Bitmap;
      import flash.filesystem.File;
  
      import qnx.ui.display.Image;
      import qnx.ui.listClasses.AlternatingCellRenderer;
      import qnx.ui.text.Label;
  
      public class FileBrowserRenderer extends AlternatingCellRenderer
      {
          [Embed(source="images/folder.png" )]
          private static const FOLDERIMG:Class;
          private var folderImg:Bitmap = new FOLDERIMG();
          [Embed(source="images/file.png" )]
          private static const FILEIMG:Class;
          private var fileImg:Bitmap = new FILEIMG();
          private var typeImg:Image = new Image();
  
          public function FileBrowserRenderer(){
              super();
          }
  
          override protected function onAdded():void{
              super.onAdded();
              this.addChild(typeImg);
          }
  
          override protected function onRemoved():void{
              super.onRemoved();
              this.removeChild(typeImg);
          }
  
          override protected function drawLabel():void{
              super.drawLabel();
              if(this.data){
                  typeImg.width = 30;
                  typeImg.height = 30;
                  typeImg.x = 5;
                  typeImg.y = 10;
                  if(this.data.isDirectory){
                      typeImg.setImage(folderImg);
                  }
                  else{
                      typeImg.setImage(fileImg);
                  }
                  label.x = 40;
              }
          }
      }
  }
  

• Difficulty accessing 1 remote desktop when connected with VPN

  Hello world

  I have an ASA 5505 and have a problem where when I connect via VPN, I can RDP into a server using its internal address but I can't RDP to another server using its internal address.

  One that I can connect to a an IP of 192.168.2.10 and I can't connect to a a 192.168.2.11 on 3390 port IP address.

  The two rules are configured exactly the same except for the IP addresses and I can't see why I can't connect to this server.

  I am also able to connect to my camera system with an IP on port 37777 192.168.2.25 and able to ping any other device on the network internal.

  I also tried ping he and Telnet to port 3390 without success.

  Here is the config.

  ASA 4,0000 Version 1

  !

  !

  interface Ethernet0/0

  switchport access vlan 3

  !

  interface Ethernet0/1

  !

  interface Ethernet0/2

  switchport access vlan 2

  !

  interface Ethernet0/3

  !

  interface Ethernet0/4

  !

  interface Ethernet0/5

  !

  interface Ethernet0/6

  !

  interface Ethernet0/7

  !

  interface Vlan2

  nameif inside

  security-level 100

  IP 192.168.2.2 255.255.255.0

  !

  interface Vlan3

  nameif outside

  security-level 0

  10.1.1.1 IP address 255.255.255.0

  !

  passive FTP mode

  clock timezone IS - 5

  clock to summer time EDT recurring

  network obj_any object

  subnet 0.0.0.0 0.0.0.0

  network of the OWTS-LAN-OUT object

  10.1.1.10 range 10.1.1.49

  network of the OWTS-LAN-IN object

  Subnet 192.168.2.0 255.255.255.0

  service of the RDP3389 object

  service destination tcp 3389 eq

  Description of DC

  the object SERVER-IN network

  host 192.168.2.10

  network of the SERVER-OUT object

  Home 10.1.1.50

  network of the CAMERA-IN-TCP object

  Home 192.168.2.25

  network of the CAMERA-OUT object

  Home 10.1.1.51

  service object CAMERA-TCP

  Service tcp destination eq 37777

  the object SERVER-Virt-IN network

  Home 192.168.2.11

  network of the SERVER-Virt-OUT object

  Home 10.1.1.52

  service of the RDP3390 object

  Service tcp destination eq 3390

  Description of VS for Master

  network of the CAMERA-IN-UDP object

  Home 192.168.2.25

  service object CAMERA-UDP

  Service udp destination eq 37778

  the object OWTS LAN OUT VPN network

  subnet 10.1.1.128 255.255.255.128

  the object SERVER-Virt-IN-VPN network

  Home 192.168.2.11

  the object SERVER-IN-VPN network

  host 192.168.2.10

  the object CAMERA-IN-VPN network

  Home 192.168.2.25

  object-group Protocol TCPUDP

  object-protocol udp

  object-tcp protocol

  AnyConnect_Client_Local_Print deny ip extended access list a whole

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq lpd

  Note AnyConnect_Client_Local_Print of access list IPP: Internet Printing Protocol

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 631

  print the access-list AnyConnect_Client_Local_Print Note Windows port

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 9100

  access-list AnyConnect_Client_Local_Print mDNS Note: multicast DNS protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.251 eq 5353

  AnyConnect_Client_Local_Print of access list LLMNR Note: link Local Multicast Name Resolution protocol

  AnyConnect_Client_Local_Print list extended access permit udp any host 224.0.0.252 eq 5355

  Note access list TCP/NetBIOS protocol AnyConnect_Client_Local_Print

  AnyConnect_Client_Local_Print list extended access permit tcp any any eq 137

  AnyConnect_Client_Local_Print list extended access udp allowed any any eq netbios-ns

  implicit rule of access-list inside1_access_in Note: allow all traffic to less secure networks

  inside1_access_in of access allowed any ip an extended list

  outside_access_in list extended access allowed object RDP3389 any host 192.168.2.10

  outside_access_in list extended access allowed object RDP3390 any host 192.168.2.11

  outside_access_in list extended access allowed object CAMERA TCP any host 192.168.2.25

  outside_access_in list extended access allowed object CAMERA UDP any host 192.168.2.25

  pager lines 24

  Enable logging

  exploitation forest-size of the buffer 10240

  asdm of logging of information

  Within 1500 MTU

  Outside 1500 MTU

  local pool RAVPN 10.1.1.129 - 10.1.1.254 255.255.255.128 IP mask

  no failover

  ICMP unreachable rate-limit 1 burst-size 1

  don't allow no asdm history

  ARP timeout 14400

  NAT static destination SERVER-IN-VPN SERVER-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  NAT static destination of CAMERA-IN-VPN VPN-IN-CAMERA (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  NAT static destination of SERVER Virt-IN-VPN-SERVER-Virt-IN-VPN (indoor, outdoor) static source OWTS LAN OUT VPN OWTS-LAN-OUT-VPN

  !

  network of the OWTS-LAN-IN object

  NAT dynamic interface (indoor, outdoor)

  the object SERVER-IN network

  NAT (inside, outside) Shared SERVER-OUT service tcp 3389 3389

  network of the CAMERA-IN-TCP object

  NAT (inside, outside) static CAMERA-OFF 37777 37777 tcp service

  the object SERVER-Virt-IN network

  NAT (inside, outside) Shared SERVER-Virt-OUT 3390 3390 tcp service

  inside1_access_in access to the interface inside group

  Access-group outside_access_in in interface outside

  Route outside 0.0.0.0 0.0.0.0 10.1.1.2 1

  Timeout xlate 03:00

  Pat-xlate timeout 0:00:30

  Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

  Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00

  Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00

  Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

  timeout tcp-proxy-reassembly 0:01:00

  Floating conn timeout 0:00:00

  dynamic-access-policy-registration DfltAccessPolicy

  identity of the user by default-domain LOCAL

  Enable http server

  http 192.168.2.0 255.255.255.0 inside

  No snmp server location

  No snmp Server contact

  Server enable SNMP traps snmp authentication linkup, linkdown warmstart of cold start

  Crypto ipsec transform-set ikev1 ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-DES-SHA esp - esp-sha-hmac

  Crypto ipsec transform-set ikev1 SHA-ESP-3DES esp-3des esp-sha-hmac

  Crypto ipsec transform-set ikev1 esp ESP-DES-MD5-esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-3DES-MD5-esp-3des esp-md5-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-256-SHA esp-aes-256 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-SHA aes - esp esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-192-SHA esp-aes-192 esp-sha-hmac

  Crypto ipsec transform-set ikev1 ESP-AES-128-MD5-esp - aes esp-md5-hmac

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set

  crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 define ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP

  DES-SHA ESP-DES-MD5

  outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP

  outside_map interface card crypto outside

  Crypto ca trustpoint ASDM_TrustPoint0

  Terminal registration

  name of the object CN = SACTSGRO

  Configure CRL

  Crypto ikev1 allow outside

  IKEv1 crypto policy 10

  authentication crack

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 20

  authentication rsa - sig

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 30

  preshared authentication

  aes-256 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 40

  authentication crack

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 50

  authentication rsa - sig

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 60

  preshared authentication

  aes-192 encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 70

  authentication crack

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 80

  authentication rsa - sig

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 90

  preshared authentication

  aes encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 100

  authentication crack

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 110

  authentication rsa - sig

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 120

  preshared authentication

  3des encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 130

  authentication crack

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 140

  authentication rsa - sig

  the Encryption

  sha hash

  Group 2

  life 86400

  IKEv1 crypto policy 150

  preshared authentication

  the Encryption

  sha hash

  Group 2

  life 86400

  Telnet 192.168.2.0 255.255.255.0 inside

  Telnet timeout 15

  SSH 192.168.2.0 255.255.255.0 inside

  SSH timeout 5

  SSH version 2

  SSH group dh-Group1-sha1 key exchange

  Console timeout 15

  dhcpd auto_config inside

  !

  a basic threat threat detection

  statistical threat detection port

  Statistical threat detection Protocol

  Statistics-list of access threat detection

  no statistical threat detection tcp-interception

  WebVPN

  username admin privilege 15 xxxxx encrypted password

  attributes of user admin name

  VPN-group-policy DfltGrpPolicy

  type tunnel-group CTSGRA remote access

  attributes global-tunnel-group CTSGRA

  address RAVPN pool

  IPSec-attributes tunnel-group CTSGRA

  IKEv1 pre-shared-key *.

  !

  class-map inspection_default

  match default-inspection-traffic

  !

  !

  Policy-map global_policy

  class inspection_default

  inspect the icmp

  !

  global service-policy global_policy

  context of prompt hostname

  no remote anonymous reporting call

  Cryptochecksum:0140431e7642742a856e91246356e6a2

  : end

  Thanks for your help

  Ok

  So, basically, you set up the router so that you can directly connect to the ASA using the Cisco VPN Client. And also, the goal was ultimately only allow traffic to the LAN through the VPN Client ONLY connection.

  It seems to me to realize that you have only the following configurations of NAT

  VPN Client NAT0 / free of NAT / identity NAT

  the object of the LAN network

  Subnet 192.168.2.0 255.255.255.0

  network of the VPN-POOL object

  subnet 10.1.1.128 255.255.255.128

  NAT static destination LAN LAN (indoor, outdoor) static source VPN-VPN-POOL

  The NAT configuration above is simply to tell the ASA who don't do any type of NAT when there is traffic between the network 192.168.2.0/24 LAN and VPN 10.1.1.128/25 pool. That way if you have additional hosts on the local network that needs to be connected to, you won't have to do any form of changes to the NAT configurations for customer VPN users. You simply to allow connections in the ACL list (explained further below)

  Failure to PAT

  object-group network by DEFAULT-PAT-SOURCE

  object-network 192.168.2.0 255.255.255.0

  NAT automatic interface after (indoor, outdoor) dynamic source by DEFAULT-PAT-SOURCE

  This configuration is intended just to replace the previous rule of PAT dynamic on the SAA. I guess that your router will do the translation of the ASA "outside" IP address of the interface to the public IP address of routers and this configuration should allow normal use of the Internet from the local network.

  I suggest you remove all other NAT configurations, before adding these.

  Control of the VPN clients access to internal resources

  Also, I assume that your current VPN client is configured as full Tunnel. In other words, it will tunnel all traffic to the VPN connection, so that its assets?

  To control traffic from the VPN Client users, I would suggest that you do the following

  • Set up "no sysopt permit vpn connection"
    • This will change the ASA operation so that connections through a VPN connection NOT allowed by default in order to bypass the ACL 'outside' interface. So, after this change, you can allow connections you need in the 'outer' interface ACL.
  • Configure rules you need for connections from VPN clients to the "external" ACL interface. Although I guess they already exist as you connect there without the VPN also

  I can't say this with 100% certainty, but it seems to me that the things above, you should get to the point where you can access internal resources ONLY after when you have connected to the ASA via the connection of the VPN client. Naturally take precautions like backups of configuration if you want to major configuration changes. If you manage remotely the ASA then you also also have the ability to configure a timer on the SAA, whereupon it recharges automatically. This could help in situations where a missconfiguration breaks you management connection and you don't have another way to connect remotely. Then the ASA would simply restart after that timer missed and also restart with the original configuration (as long as you did not record anything between the two)

  Why you use a different port for the other devices RDP connection? I can understand it if its use through the Internet, but if the RDP connection would be used by the VPN Client only so I don't think that it is not necessary to manipulate the default port 3389 on the server or on the SAA.

  Also of course if there is something on the side of real server preventing these connections then these configuration changes may not help at all.

  Let me know if I understood something wrong

  -Jouni

• Member IF ('A1' > 0) formula, THEN put an END to 'A1' + IF ("A2" > 0) THEN 'A2' END

  Hallo,
  
  how it is possible to create members as
  IF ('A1' > 0), THEN put an END to 'A1' + IF ("A2" > 0) THEN put an END to 'A2 '.
  
  thx a lot

  Funny, I present this as part of my way of thinking outside of the box presentation to KScope. As a more general formula without if statements that you could do

  'A1' * ('A1' > 0) + "a2" * ("A2" > 0);
  A1 > 0 return 0 if it is 0 or negative, and 1 if it is positive. Ditto for the comparison of the A2. The only problem with this is that you will get zeros if both are negative. to be more complete, you will need to

  'A1' * ('A1' > 0 /("A1">0) + "a2" * ("A2" > 0 / ("A2" > 0);))

  from A1 will be equal to 0 or 1 you get 1/1 which = 1 or 0/0, which = #missing all time #missing is #missing

• What are these markers of caret appearing in places under my text?

  I think they point to some invisible characters, but do not know why he's here. I could select and paste into find/replace to remove all occurrences, but he thinks he might point to some significant character for example a missing ligature. Example:

  

  I know it of something elemental, but have searched through my textbooks and google a little and did not get a response.

  5.5 ID

  Found the answer: it is a mark of index. The list of all hidden characters is:

  http://help.Adobe.com/en_US/InDesign/CS/using/WSa285fff53dea4f8617383751001ea8cb3f-6f73a.h tml