to access the LWAPP in the GUI
Hello
Is it possible to access the cisco 1242ag in graphical mode AP LWAPP?
No, you can't... GUI is accessed using stand-alone mode... If his LWAPP configure us it using GUI WLC
Let me know if that answers your question
Concerning
Surendra
Tags: Cisco Wireless
Similar Questions
-
WLC 2504 cannot access the GUI...
Hi all
I'm not sure what I did wrong, the 2504 itself has only 4 ports and no port management but I heard it's actually port 1 (even if there are no labels for this). That's what I've done so far to try to access the GUI:
in CLI mode, I have
(1) put AP managament address like 10.151.55.129 255.255.255.224.
(2) I have activated the adminmode on port 1, which I assume is management port and enabling admin mode is the same as "no shut" on switches I guess; Here is the command I entered:
(Cisco Controller) config > adminmode port 1 turn on
(3) enabled HTTPS/HTTP through commands:
(Cisco Controller) config > activate network secureweb
(Cisco Controller) config > activate network web-auth secureweb
(Cisco Controller) config > network webmode enable
(4) I then reset system and verify that the changes took place to help display the synthesis network, as shown below. I also activated mgmt via dynamic interface to see if it makes a difference:
RF-network name... TEST_WIFI
Web Mode.................................... Enable
Secure Web view... Enable
Secure Web Mode Cipher-Option high... Disable
Secure Web SSLv2 Cipher-Option Mode... Disable
Secure Web Mode RC4 Cipher preference... Disable
OCSP........................................ People with disabilities
Responder OCSP URL...
Secure Shell (ssh)... Enable
Telnet...................................... Disable
Transfer Ethernet multicast... Disable
Transfer of broadcast Ethernet... Disable
Multicast/Broadcast AP mode... Address multicast: 225.225.225.225
IGMP snooping... People with disabilities
IGMP timeout... 60 seconds
Interval between IGMP queries... 20 seconds
MLD snooping... People with disabilities
MLD timeout... 60 seconds
Interval between MLD queries... 20 seconds
Period of inactivity of the user... 300 seconds
ARP timeout... 300 seconds
Cisco AP by default Master... Disable
Join AP priority... Disable
Mgmt interface wireless... Disable
Mgmt Via dynamic Interface... Enable
Filter MAC bridge Config... Enable
Safety of bridge mode... EAP
Mesh full sector DFS... Enable
Relief of AP... Enable
Support CMCC Auth Web... People with disabilities
Web Auth redirect Ports... 80.1
Web Proxy Auth Redirect... Disable
Bypass-Web Auth Captive... Disable
Web secure Web Auth... Enable
Quick change SSID... People with disabilities
Discovery of the AP - IP NAT only... Activated
IP/MAC Addr binding Check... Activated
Status of CCX-lite... Disable
oeap-600-WLAN-dual... Disable
oeap-600 local-network... Enable
mDNS snooping... People with disabilities
mDNS interval between requests. 15 minutes
(5) I installed my PORTABLE NIC to be 10.151.55.20 255.255.255.224 and connected to port 1 on wlc 2504; but I can't ping 10.151.55.29 nor do I navigate to https://10.151.55.29/. The port appears upwards (the flashing green lights on port 1 and Portable NIC also Flash).
Any help would be appreciated
If your connection to your laptop direct to port 1, then you have untagged the management vlan. Now you have configured for vlan 10, you must set to vlan 0.
You will then be able to ping to the management interface and connect to it through the user interface.
Sent by Cisco Support technique iPhone App
-
New SGE2010 - cannot access the GUI
Hello
With allot of excitement, I decided to buy a port of 48 x 10/100/1000 Ethernet to our company SGE2010 to get inside DHCP, DNS and net administration on metal.
I was under the impression that the initial installation has been taken and playable, but the reality was very different. I started to connect the switch to our existing infrastructure without success. After that I tried to connect to the graphical interface to see if the configuration is turned off, but has been unable to connect (used default 192.168.1.254). Once I disconnected the switch of our network, did a factory reset and connect a single computer to the (tried various port), and yet I could not connect.
In the end I had to dust off an old machine with serial port and connect to the switch via the port console to see what was going on. Configuration options in the console had to say at least minimal, but I could see that both http and https are enabled, the device ip is 192.168.1.254, disabled DHCP, VLAN 1 id, default as stacking mode system settings was on stackable (autonomous tried without success), and Layer 2 on.
I'm very surprised that I can't connect to the webgui through a nettbrowser of the turnout, since that looks at what stage 2 in management manual. Here, it is said that you should be able to connect using one of the 48 ports.
For those who wonder then there is no firewall enabled on the client, and this is a new installation windows xp machine that I use to connect and ie6. The switch firmware is 3.0.0.18 which is the most recent.
I would be grateful for all the help I can get because I'm running out of options. Am I missing something or is the switch faulty?
Hi Rafn,
Maybe the quick start guide should indicate,
step 1. You have defined your ethernet PC card to address 192.168.1.100 IPv4 or similar with a subnet mask = 255.255.255.0 and try this action IE7 + again. http://192.168.1.254
Try it now, it should work, but remember that if you change the IP address of the switch to another network management for example 192.168.100.x where x is a number, you will need to change the IP address of your PC as well.
best regards and fun Dave
-
Cannot access the ISE-3395-K9 CISCO Web GUI
Hello
I can't access the ISE-3395-K9 web gui interface concert 0 with ip address is 192.168.1.10. I put the ip address of my labtop to 192.168.1.20 and could ping back but am still not able to access them through a direct connection between my labtop to concert interface 0 using one of the supported web browsers. Any help would be greatly appreciated.
It is possible that the GUI was configured to restrict access to only certain IPs / subnets. If 192.168.1.x isn't one of them, then you will have access.
Are you able to connect to the shell via SSH? If so, you should check and confirm that all associated ISE services run by running the following command:
show the application status ise
Thank you for evaluating useful messages!
-
Hello
This is so the API, I downloaded and imported into my project->
http://www.BlackBerry.com/knowledgecenterpublic/livelink.exe/fetch/2000/348583/800332/800505/800608/...When I run it, I get "Error trying to access the api Module secure"
It says its taken in charge for OS 4.2 and I think, so execute me on my blackberry 9900 OS 5 should work,
I've been on these forums before and after the solutions, I ordered the signature of the key codes and signed the project as well.This is what appears in the signature box, just code until I run it:
It compiles without error, but it still does not work.
What I'm doing wrong exactly? Any help would be appreciated!
Khalique - AminaHey everybody,
Anyone else who has this problem with these particular CBC of the advanced downloadable user interface files.
Make sure the following is in place.Your JRE version is important.
If you test on a device that is older than 7.1Change your JRE in a right click on the JRE and selecting the right JRE for your device. [some of you may need to download the right JRE].
I installed the plugin for eclipse blackberry, so he automatically gave me all the available JRE. I just had to change.
After that I changed it, I have not the reddest comments when I signed the code.
AND
It worked fine, no error message popping up for ' api access blocked attempts to.
If anyone has questions and is the same problem. Please ask. I've spent hours on it, and I'd be happy to help you if I've been unclear!
Take care! -
Cannot access the AIP SSM via ASDM
CISCO recommendations below:
Cannot access the AIP SSM via ASDM
Problem:
This error message appears on the GUI.
Error connecting to sensor. Error Loading Sensor error
Solution:
Make sure that the IPS SSM management interface is up/down and check his IP address configured, default gateway and the subnet mask. It is the interface to access the software from Cisco Adaptive Security Device Manager (ASDM) on the local computer. Try to ping the address of management of IPS SSM IP interface on the local computer that you want to access the ASDM. If it is impossible to do a ping check the ACLs on the sensor
----------------------------------------------------------------------------------------------------------------------------------------------
I've tried everything recommended above. I can ping the host ASDM the FW and the SSM-10 module. Well, I ping the host machine and the SSM of the ASDM. I opened as wide as possible ACL. I changed the IP addresses and masks several times. The management of the ASA port and the SSM and the PC are on the same subnet.
A trace of package from the PC to the SSM shows that it is blocked by an ACL rule, and yet I opened wide. I've seen this kind of problem before and it was solved by applying the double static NAT, but I don't know how to do that if all the IP addresses are on the same subnet.
Tried everything, need help from high level.
The IDM software that comes with ASDM does not support java 1.7. The portion of the ASDM ASA supports 1.7 but launch the IPS cmdlet works only with 1.6. The TAC enginner suggested that I use the IME (IPS Manager Express) which is available for free on the Cisco's (http://www.cisco.com/en/US/products/ps9610/tsd_products_support_general_information.html) Web site.
I've been playing with it today, and so far it seems to work pretty well.
-
Air 1131AG - cannot access the unit with http
I just bought two 1131AG and am not able to access the unit with Internet Explorer.
The two units Gets an IP address from my DHCP server and not to ping requests. Unfortunately, 21, 80, and 443 ports are not open and IPSU Cisco sees not the device either.
The fact that I have two new units that have exactly the same problem makes me think I'm doing something wrong.
I also have access to the consoles.
Thanks in advance.
Based on the number of your room, you have just taken delivery of the Lightweight Access Point. You need to convert the LWAP in standalone (if that is your intention).
Convert a standalone Lightweight Access Point
Click on the link above and the procedure you're looking for is under the heading "Using a TFTP Server to return to a previous version".
Good luck.
Please rate when useful and/or there is. Thank you.
-
Connection WIFI mobile phone to the laptop, so I can access the web of the cell
My laptop is connected to the internet by internet dongle, I want to connect my cell phone to the laptop via WIFI so I can access the Internet from the mobile phone, how to put in place on windows 7?
You can configure a network hosted with your Windows 7 machine. Here are a couple of free GUI frontends to the netsh commands that implement this. These turn a computer into a virtual router Windows 7 wireless.
http://virtualrouter.codeplex.com/
http://www.Connectify.me/index.html
Assuming that your USB dongle is a device high-speed 3G / 4G, you might also look into buying a router. Some examples...
http://3gstore.com/index.php?Main_Page=index&cPath=35
The advantage of the router, it is that you need not the Win 7 PC all the time so that your other devices have access to the public internet.
MS - MVP Windows Expert - consumer
"When all else fails try what the captain suggested before you started...". » -
cannot access the web page of WAP but can telnet
Can someone tell me why the following configuration won't let me access the web page of the WAP?
version 12.2
no service button
horodateurs service debug datetime localtime
Log service timestamps datetime localtime
encryption password service
!
hostname EwingWAP
!
logging buffered information
enable secret 5 $1$ z9vV$ M.rY40womPNf7YPOQqC8T.
!
username privilege 15 secret 5 careone $1$ nFXA$ ezjkiBAHeboaKYMzB4hpq.
clock timezone IS - 5
clock to summer time EDT recurring 2 Sun Mar 2:00 1 Sun Nov 02:00
IP subnet zero
!
!
Bridge IRB
!
!
interface Dot11Radio0
no ip address
no ip route cache
!
SSID tsunami
open authentication
Comments-mode
!
base speed - 1.0 2.0 basic basic-5, 5 6.0 9.0 basic-11, 0 12.0 18.0 24.0 36.0 48.0 54.0
threshold RTS 2312
root of station-role
Bridge-Group 1
Bridge-group subscriber-loop-control 1
Bridge-Group 1 block-unknown-source
No source of bridge-Group 1-learning
unicast bridge-Group 1-floods
Bridge-Group 1 covering-disabled people
!
interface FastEthernet0
no ip address
no ip route cache
automatic duplex
automatic speed
Bridge-Group 1
No source of bridge-Group 1-learning
Bridge-Group 1 covering-disabled people
!
interface BVI1
IP 172.18.86.5 255.255.255.0
no ip route cache
!
default IP gateway - 172.18.86.1
IP http server
IP http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivor
y/1100
radius of the IP source-interface BVI1
1 channel ip bridge
!
!
Line con 0
line vty 0 4
local connection
line vty 5 15
local connection
!
NTP-period clock 2860650
NTP 208.90.144.53 Server
endHi Jason,
Have you tried the default user name and password?
Username - Cisco
Password - Cisco
Please try the commands below and let me know how it works...
en
conf t
AAA new-model
local IP http authentication
end
Try to open the WEB GUI by using the configured user name and password...
Concerning
Surendra -
To access the currently selected keyframes
Is there a way to access the keyframes selected currently through javascript? I'm writing a GUI which will stick the currently selected keyframes (or copied keyframes could work too) on a layer specified user when you press a button. And secondly, is it possible to have all the additional attributes, such as ease in deceleration example?
Thanks in advance!
Indeed, I wrote this from memory and it's fake...
It is: position.keySelected (idx);
and in general the syntax to read a something key is myProperty.keyXxx (idx);
and not what I wrote. I'm sorry.
But well, if you have access to the table of methods in the guide of script... they're all here.
Xavier.
-
Can I access the guest from the server OS (virtual machine)?
Hi all
Can I access the guest from the server OS (virtual machine)? I mean, I would also like to start and discovers a guest OS (VM) directly in the server as in VMware Server 2.0. I would also like to see the graphic on the server management console to manage virtual machines.
Or do I always have at least two computers? For example, the server ESXi without GUI / frontend access and the client with vCenter, vInfrastructure, blah-blah-blah,...?
Thanks for the replies!
Best regards
Joao Araujo
You will need the Client or another tool for access (RDP, SSH) a machine separate. ESXi is a very tiny BONES.
-
How to start to use the Oracle client to access the database?
People,
Hello. I just installed Oracle Client (Instant Client) in the directory/home/myOracle/Oracle_Client.
But I don't know how to start and configure the client to access Oracle database.
Can all folk tell me how to start to use the Oracle client to access the database?user8860348 wrote:
People,Hello. I've successfully used Oracle SQL Developer. But I want to know how to use the Instant Client.
Can any folk tell me how to use the Client then just install it?
I guess you're hurting understand the definition of Client instant, there isn't a tool or application or tool GUI as a sql developer or another that you can start using. It's just client installed with the minimum characteristics
If you want to use the right application tool install sql developer in your instant client or simply running sqlplusSee you soon
-
Unable to access the web browser 7.0 DSCC
Hello.
I just installed Oracle Directory Server Enterprise version 7.0. on one "5.10 Generic_142900-13 sun4v sparc SUNW, Sun-Blade-T6320. I used the package install and crossed all stated in the installation manual, with the exception of the part of Application Server.
Trying to access the admin gui dscc via internett Explorer (http://directory server host: 3998/dscc7)
I received the message:
$ 0 x PŠ1.3.6.1.4.1.1466.20036
Do I need an application server to start the web console dscc as wel?
Thank you very much
Sigurd Lyngås
Nets of Norway ASYes, you must publish the war file (that you have created during installation) to an application server (Tomcat / Glassfish / etc.). I found to be the easiest to configure on Solaris - Glassfish was about as easy as copying files in place and the execution of a single command.
-
I can't access the backups on Time Capsule
A month ago I deleted from my hard drive and more. I have a MacBook Pro 2012 running macOS. I can't access the files on Time Capsule before is erased in the month of August, I can see the story in the timeline panel, but I don't have access to anything before erasure. Is it possible to access to the files before the wipe?
A month ago I deleted from my hard drive and more.
What hard drive you are talking about: one internal on your MacBook Pro (MBP), an external drive attached to the MBP for Time Machine backups, or internal hard drive to time Capsule?
-
Can I access the real coordinates of an image in iPhoto?
Can I access the real coordinates of an image in iPhoto? Places shows a rudimentary map of the location of the photo, but I would like to retrieve numeric values.
Not in ipHoto, but if you export the non modified original and then open with preview the Inspector will display numeric values assuming that they are in the EXIF data
LN
Maybe you are looking for
-
Satellite A210-171 - maximum capacity of a hard drive?
What is the max HDD capacity satellite a210-171 may take?
-
How to connect a Qosmio G30 to the TV
Could someone help me please. I'm not good with computers if at all really need. I want to conect my Qosmio G30 to my TV. It's an old TV not LCD or plasma. I have a cable with my laptop which connects the laptop to the TV via a connection SCART. I th
-
Error - cannot open ACPI Kernel Mode Drive
This message comes at the beginning of my system Windows 7 RC 64-bit. The only symptom is detected, it is the brightness of the display switches back to minimum when I delete the message. Any other solution than making a clean installation?
-
I tried to change the opener by default to IE, but it does not work either...
-
Corrupt resettlement of my Pavilion a6009n desktop computer...
Hi all... I decided to do a reinstall of my OS Windows Vista(32bit). I have ordered from HP recovery disks when I forgot my Windows password. I did it several times before, but this time, something is very wrong! It went normally, but I noticed a few