to access the network of vision builder error

Similar Questions

• Cannot access the network drive or impossible to mount the network drive. Error "network path was not found.

  Original title: network path was not found

  HI, after the upgradation from windows xp sp2 to sp3 (next to the customer) I can't access the network drive or impossible to mount the network drive. ' ' It showa error "network path was not found.

  Hi gauravadavadkar,

  Thanks for posting your query in Microsoft Communities. Provide the following information:

  ·         Did you do changes on the computer before the show?

  ·         What is the full error message?

  ·         Work on a domain?

  Follow these methods.

  Method 1: Temporarily disable the security software.

  Note: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you do not disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network during the time that your antivirus software is disabled, your computer is vulnerable to attacks.

  Method 2: Follow these steps:

  Step 1: Start the computer in safe mode with networkand check if the problem persists.

  S tep 2: if the problem does not persist in safe mode with networking, perform a clean bootto see if there is a software conflict as the clean boot helps eliminate software conflicts.

  Note: After completing the steps in the clean boot troubleshooting, follow the steps to configure Windows to use a Normal startup state section of the article to start the computer to a Normal startupmode.

  After the clean boot used to resolve the problem, you can follow these steps to configure Windows XP to start normally.

  (a) click Startand then click run.

  (b) type msconfigand click OK.
  The System Configuration utility dialog box appears.

  (c) click on the general tab, click Normal Startup - load all device drivers and services, and then click OK.

  (d) when you are prompted, click restart to restart the computer.

  Method 3: Follow the steps in the article.

  How to troubleshoot a network home in Windows XP

  In Windows network connection issues

  You can read this article for more information:

  Windows wireless and wired network connection problems

  I hope this helps. Let us know if you need more assistance.

  Thank you.

• I'm trying to uninstall Adobe error could access the network location. I'm not on a network any more

  I'm trying to uninstall Adobe error could access the network location. I'm not on a network any more and need to uninstall it and buy a new

  Hi kristiel49687537,

  Try to use Microsoft Fix it Wizard, available at support.microsoft.com/kb/886549. This wizard updates the Windows registry.

  Warning: Adobe does not support third-party software and provides this information free of charge only.

  If you cannot resolve the problem after using the fix it Wizard see solutions in Error 1606 | Install | Acrobat 8, 9. CS4

  Kind regards

  Nicos

• "Could access the network location:.."

  I get the "could access the network location:. «error with installing and uninstalling of programs, i.e. iTunes, Quicktime.»»
  I checked the Internet and found registry patches, but they have not worked for me. I tried the Fix It program in one of the solutions, not good.  I also stop my firewall and anti-virus and tried to install it that way. no go.

  I have Windows XP, SP3

  any suggestions?

  I thought about it... have an external hard drive which I usually turned off when the use not. I tried to install everything with it on and it worked.
  Thanks for your help

• Unable to access the network using Edimax N300 universal Wi - Fi extender

  Original title: Edimax Extender will not get internet access

  I naoual got a N300 Eimax universal Wi - Fi extender but I am unable to connect to the internet.  They suggest setting up near the wi - fi access point to get the signal stronger and I got to show connected in the window ' currently logged in ', but it does not connect to the network.  EDIMAX has proposed upgrading the firmware, but I was unable to get any joy with that either.  Anyone with any ideas would be appreciated.

  Hi Gofchap,

  Thanks for the question of validation in Microsoft answers community!

  I imagine the frustration you feel when you are unable to access the network.

  The problem may be because of the Extender, diverter, or with the network adapter.

  1 did you do changes on the computer before the show?

  2. do you receive any error messages?

  3. What is brand and model computer?

  4. have you tried to connect without using the extender?

  I suggest you to visit:

  Wireless and wired network problems

  http://Windows.Microsoft.com/en-us/Windows/network-connection-problem-help#network-problems=Windows-7&V1H=win8tab1&V2H=win7tab3&V3H=winvistatab1&v4h=winxptab1

  I hope this helps. If the problem persists, let know us and we would be happy to help you.

• Must be able to access the network WPA PSK

  Hello

  I just got my laptop Satellite Pro L300. I have a sky broadband wireless router in my house and it works with my computer and my laptop roommates but not with the Satellite Pro.

  Phone heaven Support and they told me to tell you that my laptop is not recognising non secure networks and I should be able to access the network WPA PSK.
  What should I do?

  Kind regards

  >.. .but not with the Satellite Pro.
  Does that mean exactly?
  You see that this guaranteed WLAN?
  Can you put WPA password to have full access or what?
  What exactly happens?

• Windows XP sp3 can not access the network shares on vista after installing sp2

  I have a xp sp3 computer and another currently running vista Home premium sp2. Previously, I was able to access the network share on the xp computer before vista computer I installed sp1. Both computers were able to ping between them without problem.

  I've upgraded to sp2 because I had problems with windows media center, missing records. Upgrade of these issues fixed, but this means that roll back to sp1 is not an option for me to get operational network.

  Please do not post a standard answer on the network configuration. I am familiar with the standards requirements to share files between xp and vista and everything is set up correctly.  Like I said everything was working fine before the installation of sp2.

  If it is a known problem that is still not resolved, I'd appreciate knowing that information as well.

  Edit: Firewall been disabled during my troubleshooting

  After more work, I was able to solve my problem.  Update zone alarm solved my problem and helped my windows xp machine to access my Vista network shares.  As I pointed out in the original post, zone alarm firewall has been disabled during my troubleshooting.  Apparently, when disabled, the old version of zone alarm has always been the origin of the problem.

• Cannot access the network ERR_NETWORK_ACCESS_DENIED

  I have Windows 7.  Nothing works, I tried chrome (which will not even load) and Firefox (it has been a constant problem with gmail for well over a year).

  Cannot access the network

  ERR_NETWORK_ACCESS_DENIED
  Google Chrome has access to the network.

  Maybe it's because your firewall or antivirus software wrongly think that Google Chrome is an intruder on your computer and it blocks to connect to Internet.

  Chrome allow access to the network in your firewall or anti-virus settings.

  If it is already listed as a program allowed to access the network, try to remove from the list and Add again.

  I tried the above, but can't seem to solve the problem.  Thank you.

  Hello Paul,

  Thanks for posting your question on the Microsoft Community.

  I would like to know some information about the problem so that we can help you better.

  The same problem occurs when you use Internet explorer?

  Thank you for details on the question and your efforts to resolve.

  If the problem also occurs when you use Internet explorer, I suggest you use the steps in this article and check if it helps.
  Reference:
  Can't access some Web sites in Internet Explorer
  https://support.Microsoft.com/en-us/KB/967897

  Note: The feature reset the Internet Explorer settings can reset security settings or privacy settings that you have added to the list of Trusted Sites. Reset the Internet Explorer settings can also reset parental control settings. We recommend that you note these sites before you use the reset Internet Explorer settings. Reset Internet Explorer is not reversible, and all the previous settings are lost after reset.

  Also see this article:
  Understanding Windows Firewall settings
  http://Windows.Microsoft.com/en-us/Windows/understanding-firewall-settings#1TC=Windows-7

  Note: Firewall and Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not turn off your antivirus software and firewalls. If you need to disable temporarily to install other software, you should reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software and firewall are disabled, your computer is vulnerable to attacks.

  To get help on Google chrome, I suggest you post your question on Google chrome forums.
  http://productforums.Google.com/d/Forum/chrome

  I hope this information helps.

  Please let us know if you need more help.

  Thank you

• Can I cache of RADIUS credentials used to access the network devices?

  I would start by RADIUS to authenticate users who try to access the network through virtual private networks devices. Since we will need to access the equipment in the case of a VPN does not, I need to know if the credentials may be cached on the device.

  You mean devices are accessible once you have set up VPN. Failure VPN, you can even ping the network devices. I am assuming that they would be internal resources. In all cases, credentials may not be cached on the device. Let me know if I am missing any room in your questions. ~ Jousset

• Smartphones blackBerry 8310 and 8110 "attempted to access the network.

  Good day to all.

  In my application I m send and receive sms.

  It works very well in 8110 but in the 8310, while sending or receipt of the msg it always ask

  authorization "the appl." XYZ "has attempted to access the network. You want to allow this? "   .

  And if I press on no when you receive the msg then it never to catch the incoming msg again until I have leave the Apllication.

  Why is it so?

  Is this for safety reasons or '?'.

  Is there a solution to stop this.

  In 8110 it never ask such Question and works smoothly...

  Please help me solve this problem?

  Thank you & best regards

  Thakur

  I found the solution... I got my code... signature keys and my application is signed exception so not more security

• Cannot access the network using WiFi hotspot

  I have a lenovo ideapad z570 running windows 7 ultimate, processor intel pentium cpu B950 @2.10 GHZ 2 GB ram and 64-bit operating system. My problem is that when I create a wifi hotspot via intel my wifi technology, I so can not access the network on my android phone or the playstation 3. There is a sign yellow triangle on the wireless icon and I have the cursor on it, she reads, access to the internet network, unidentified network no internet access. I tried to update all the drivers, I even reinstalled the operating system after a wipe, same result. I tried to use programs such as connectify but same result. Please help me

  Original title: network
  

  There is a sign yellow triangle on the wireless icon and I have the cursor on it, she reads, access to the internet network, unidentified network no internet access. I tried to update all the drivers, I even reinstalled the operating system after a wipe, same result. I tried to use programs such as connectify but same result. Please help me

  Hello

  You try to use the Add-hock network so that you can access ac in android are as good as play station unit
  Like you would have checked in the id network properties material and device id, it yellow list means problem with driver, please try to update the BIOS and the driver appropriate with the hardware ID, if possible to install from the laptop power management

  IdeaPad Z570.please press fn + f5 and check the layout state of WIFI is turned on, current state should off
  Download these drivers and install it, then try again
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1WLN90WW5.exe

  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z370Z470/IN8STW09WW5.exe
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1MEI08WW5.exe
  http://download.Lenovo.com/userfiles/Driver/en/downloads%20and%20Drivers/Z570/Win7/IN1CHP30WW5.exe

• Virtual machines are not able to access the network after you have moved the host

  We moved our 4 ESX host to a different physical switch and now our VMs cannot access the network.

  I can access the host via client vsphere.  Our host has 2 network cards.  They are both members of the vSwitch0.  I have 1 VM network defined, and they are both members of it.  The network adapters, vmnic0 and vmnic1 are also part of my VMkernel which I do not know that I need because I have 1 ESX Server and do not use iscsi or NFS.

  the two cards are also part of my service console.

  According to my host "configuration / display: vitual switch, it looks like all my virtual machines are defined to use the vswitch."

  the two physical network adapters is connected to the same switch.  I did not go to any configuration on the switch.

  

  The steers would be appreciated.

  Thank you

  Paul

  

  Welcome to the community,

  It sounds as if the physical switch ports are not configured correctly. Please check that port security is disabled on the switch (switchport mode access) ports and spanning tree portfast is (if any).

  André

• The share of customers unable to access the network - error 0x80004005

  Hello, my network has the following configuration.

  • Server - Windows 2003 Server - acting as DNS, domain controller, file server
  • Clients - Windows XP Pro, Windows Vista business, Windows 7 Pro
  • DHCP server is on my router. All customers running on DHCP

  For some unknown reason, some network sharing has stopped working since yesterday. When users connect by Ctrl + Alt + Delete by using their network accounts, they are unable to access their computers in office, services, Skype etc., gives an error of 0 x 80004005 (unspecified error). They are not forced to use roaming profiles.

  I opened Windows Explorer and typed \\server\share. The same error is invited. However, if I try to access the share of \\ip\share, it can show me the files without a problem.

  I took to refine measures issues

  • Connectivity - outcome of the network: Internet access / access server by IP. So no connectivity problem
  • Ping-ing the name of the computer server - result: OK. So not a DNS problem
  • Check firewalls – result: Clients running Windows Firewall correctly. Network type, the value of 'work '.

  Other facts that may be useful

  • No third-party firewall. All running on Windows Firewall.
  • No settings changed before problem appeared
  • Problem appeared after a reboot the server

  (P.s. Skype prompted "Cannot find necessary files and cannot start". "I think it's the same problem with network shares, because the application data is also stored in network shares.)

  Hello

  Your question of Windows 7 is more complex than what is generally answered in the Microsoft Answers forums. It is better suited for the IT Pro TechNet public. Please post your question in the Forums TechNet Windows 7 Technet.
  Here is the link:
  http://social.technet.Microsoft.com/forums/en-us/category/WindowsServer

• Vision Builder - error creating LabVIEW Code

  Hello!

  I use Vision Builder 3.5 and LabVIEW 8.5.1. Vision Development module is also installed.

  I've built several routines inspection with the Vision Builder. Then I tried to create .vi-files. Then I hit tools-> Inspection migrating to LabVIEW...

  In the next box I select:

  1-version of LabVIEW: LabVIEW 8.5 - NEITHER Vision 8.5.0

  2 - the directory I want vi-files to be.

  The migration begins, but it is never finished. There is always the following error message:

  Error during creation of LabVIEW Code #3

  I have not found additional information about this error code. So maybe someone is able to help.

  Thanks in advance.

  It seems that the error occurs when you try to play a file which contains the parameters of control of that Vision Builder AI generates. This file may have been corrupted and Vision Builder AI fails to write correctly. I have attached a simple VI to determine where this file lives. Make sure that the file is not present before generating the code and that you have write access to this directory.

  Hope this helps,

  Brad

• Cannot access the network drive after trying to change the shared folder.

  I had a 80 GB drive connected to my E3000 for a few years and it worked without problem. I recently turned to a 250 GB Maxtor One Touch drive. When I plugged it, the router automatically creates a shared folder. I was able to connect to this folder without problem, but I wanted to share the whole score. When I made this adjustment and tried to save the settings, I temporarily lost access to the router. He gave me the standard page cannot be error message appears. When I got access changes seem to be made. When I try to access the drive of my laptop I get this error message, "the mapped network drive could be created", "the name specified network is no longer available". I rebooted and power rolled my router as well reconnected the drive.

  I think that since you have replaced your hard drive, old settings are configured may still on the hard drive of old. You can change the users and group so that it syncs with the new hard drive or start from scratch (reformat the hard drive).