Toshiba 32LV933G still scanning loop. Does not start

Similar Questions

• Still 2 WT10 does not start

  Hello

  My Encore 2 WT10 lights. I updated the bios to 1.4 via the USB port. It does not start after the upgrade. The screen remains black. I can load and reload my mobile phone via the tablet or a USB Hub to power. If I press the button for 30 seconds, turn off the USB device, press the button again turns on USB power. But the screen stays black, no screen BIOS or Windows, no audio or USB data connection (or other signs of life).

  I think that my tablet is in soft-power-off mode. How can I hard-power - off the shelf without removing the battery internal?

  Try to open the BIOS/UEFI tablet settings by following these steps:

  Press and hold the volume button at the same time by pressing the button for a few seconds. Ideally, this will open the screen of the BIOS/UEFI. Once this is done, make sure that the settings are correct or restore the factory settings.

  If that does not help, then additional assistance may be required.

  In a similar way a lot, the splash screen appears where you can recover your tablet from an image that you created previously (recently) or in the worst case, reinstall Windows.

  Also keep in mind that between reboots, a 10-15 minute interval may be required (don't know why, but it helped me dealing with errors in the past).

  My impression is that the BIOS 1.40 was already installed in the WT series, so some models have been improved to 1.60. BIOS should normally updated via WIndows Update or Toshiba service station.

  Hope this helps

  BR

• TOSHIBA HWSetup in Control Panel does not start

  All the updates of Bios, drivers, WindowsXP SP2 is installed. The utility called "TOSHIBA HWSetup" does not start from the control panel. Could use some help here because I like to adjust some more advanced settings of my laptop.
  PS: How can I access the Bios settings?

  Hello

  I put t know which model of laptop you have, but in my opinion, you should try to remove this utility and install it again. You can download it from the download from Toshiba site.

  Try to enter the BIOS settings using the ESC key at the beginning upward.

  Good bye

• Why a while loop does not start in a flat sequence if I have another loop running in a different sequence of flat?

  Hi all

  Basically, I'm in the order of many device and regulation for that pourpose, I created a sequence of plate to do. Also, at times I have start the potentiostat measures I use too, which follows a sequence and I created a second flat sequence to do this. In a part of my experience, I want to follow the voltage and current of high voltage power supply that is located in the flat main sequence and also read the results I'm getting with the potentiostat simultaneously.

  In the main sequence, there is a constant bollean which triggers the beginning of the secondary sequence. In the framework after it contant Boolean, I have a while loop in which I read 2 analog inputs of the power supply high voltage with my USB-6218 for awhile every 100 m, my problem is that the Boolean constant actually starts the subsequence flat but when it reaches a while loop in which I continue to read the results of the potentiostat , for a reason that the operation does not start until the while loop in the main loop is not finished.

  I communicate with the software of the potentiostat through a driver made by the manufacturer.

  Is it possible to read analog inputs with USB DAQ and simultaneously read the results of the potentiostat?

  Thank you very much

  Without being able to see the code, can only speculate. My guess is that you have probably some data flow to the second loop that depends on the first loop finish.

• Toshiba L 40, 7335 does not start

  I have a Toshiba smart l7335, that it does not start.

  At the beginning the indication led starts green and at the end of 2-5 seconds looking past automatically mode and indicator led turns red.

  The screen seems to be turned on but no signal at all or the remote control does not work.

  I did reset procedure disconnect the apparatus of power but the problem is the same.

  Any reset procedure is possible?

  > Any reset procedure is possible?

  This procedure does not exist for TV sets.
  I'm afraid that the material of the TVs is affected and probably the engineer must verify your device TV m.

  So my advice is to get in touch with service partners as soon as possible.
  I hope that the warranty is still valid and could be repaired for free.

• Toshiba accessibility TACSPROP (Fn keys) does not work on my Satellite A100

  Laptop A100-097

  I am facing a problem with the extraordinary on my keyboard * FN keys * managed by program "* TACSPROP.exe*" which is located in *C:\Programmi\Toshiba\Utilities\.*
  This program does not start automatically at startup and if I manually run his way a window is also come say * "Questo sistema non Può utilizzare Toshiba Accessibility" * (in Italian: "" * cannot use this system Toshiba Accessibily * ' ").

  I can't identify the installation program appropriate for the program in the list of drivers that you provide support download page, but I can tell you that the program is in the same directory where the Software * Hardware Support * is installed.

  Please, can you provide me with the Setup program for this program? I think I'll have to try put it back.
  Is it possible, that it has been marked as a Spyware of Vista or AVG? Maybe some windows update changed something...

  Help, please!

  Thanks in advance

  Hello

  These types of problems are very strange to me, and I wonder why this happen. The fact is that the recovery image (recovery DVD) is very well set up and there is absolutely no problem with the use of the FN keys. All these functions of FN keys are tested and it should work. All the necessary services will begin with OS and you must be able to use all the key functions of the FN.

  I don't want to speculate what the problem is here, but I can't imagine you have this problem on the first day.

  Now the question is: why is that you get? Using the factory preinstalled OS or you have installed your own version of the OS?

• Satellite L850: Catalyst Control Center does not start

  Hello, I have an AMD 7670 m dedicated graphics card and when I install the AMD display drivers downloaded from the toshiba site, the Catalyst control does not start and he also seem to have problems with the usb ports and my wireless stops working for some reason any.

  Is that what I can do on it or am that I better use the downloaded drivers directly from AMD? Thank you

  Maybe stupid question now, but why do you need it? Have you been preinstalled OS with your laptop or you bought for laptop computer without an operating system preinstalled?

  What model do you have exactly (L850-xxx)?

• Windows 7 printer spooler does not start

  just my printer spooler does not start in Windows 7.  I received a message that the spooler wasn't running when I tried to use it today.  I used the printer for a few days. "net start spooler" fails from the administrator command prompt.  I checked that the CPP is running.

  I installed SP 1 yesterday with success, but I went back to the restore point, but still, the spooler does not start.

  The system acts as the spooler is missing.

  How can I solve this problem?

  Thank you

  Jim

  I would like to check the status of the Services.

  Click on the Start button and select Control Panel, administrative tools, Services. Locate bridge end RPC Mapper in the list. Check that he started and that the startup type is automatic. If it is not set to automatic, right-click and select Properties, general tab. There is a box after the startup type. The options are available in a menu drop-down by clicking on the down arrow to the right of the box. Make the change and click apply and then click OK. Restart the computer and verify if it has started.

  Repeat the procedure for DCom server process Launcher.

  It is always sensitive in this situation to achieve a malware check.

  Start the computer in safe mode with network and download and install Malwarebytes (free version for individuals only), updated definitions and run in safe mode. Disable other security software while you do the analyses.
  http://www.precisesecurity.com/how-to/HT-smodewnet.htm
  http://www.Malwarebytes.org/
  Download and run SuperAntiSpyware (Free Edition)
  http://www.SUPERAntiSpyware.com/download.html

  Some malware is installing the entries of proxy server redirecting internet connections. If you encounter this problem step 2 see in the following link:
  http://www.myantispyware.com/2011/02/21/how-to-remove-Internet-Security-Essentials-virus/

  Currently, this is a good combination that seems to detect more malware, but it can miss the malware as all security software can do.

• 9.01 Firefox does not start, has a dialog box saying: it is still ongoing.

  Does anyone have ideas with the following Firefox Vista problem.

  9.01 Firefox does not start, has a dialog box saying: it is still ongoing.

  There is no instance of firefox in the Task Manager.
  I uninstalled firefox and reinstalled both of
  Desktop mode and course in vista.

  I have deleted all instances of firewall.

  I tried with firewall failure

  Still having the same problem

  Solved by uninstalling all the firefox - including my settings

• Toshiba Q300 480 GB HARD drive does not start after migration

  Hello

  I bought a disc of Q300 489 GB to replace a small 840EVO of Samsung. I used the toshiba tool to clone the smallest to the largest player. However when the clone is finished and the reboot of the machine the machine hangs just at the start of the process (before starting windows 10). If I go back to my little samsung it starts without a problem.

  I tried to treat twice with NTIEcho and also tried with Partition AOMEI tool, all attempts have failed to start on the Q300 drive.

  I am just tempted to refer the reader to Ebuyer, getting another Samsung. Maybe Toshiba can tell me how to get the drive working properly?

  Regards Sean

  PS. can someone direct me to a page where I can raise a ticket of Toshiba, I would be grateful. There seems to be some links broken on the UK site.

  Hello.
  Do you have an error message when the operating system does not start? Appearing in AOMEI Partition Wizard you have been used during the replacement of the Samsung drive?
  After the largest disk cloning, you may need to change the boot settings in the BIOS or to remove the previous Samsung drive to test.

• Toshiba Satellite L70 - B does not start the BIOS or OS

  Hello

  I changed the same parameters (UEFI priority CSM to start: FIRST USB) in the Bios and saved them, now computer laptop does not start, I can't enter BIOS more... Just see a black screen... I tried to remove the pulp and power, clicked on the power 1 m button, but nothing has changed...

  I can fix this please

  Laptop model: Toshiba L-70-B

  Any help please?

• DVD - ROM Toshiba Recovery disk does not start

  Hello

  I'm having some problems with my Toshiba Satellite M40, and I decided to reinstall the OS with the recovery of the dvd disk, but the disk does not start.
  When I'm on windows, the cd/dvd driver works perfectly, and I don't think that the recovery of the dvd disk are damaged.
  I have already tried:
  1. by pressing the "C" key to start the computer
  2 - press "F12".
  3 - Enter the BIOS Setup and select cd-rom to start first

  But the computer starts up normally and no error message appears

  Can someone help me? I don't know what to do

  Thank you

  Hello Palma

  Can you please test it with some other bootable CD or DVD? It will be interesting to know if this happens with the recovery media only or even with other bootable media.

• Equium M40X: I get to the banner of Toshiba, but Windows does not start

  When I start my 2 year old Toshiba Satellite M40X, I get to the banner of Toshiba, but Windows does not start. I tried using the recovery CD and it does not either.

  Any suggestions as to what could be the problem?

  Hello

  What do you mean with the banner of Toshiba? Did you mean the Toshiba splash screen that appears at the begging of the boot?

  Equium M40X successfully passed this screen?

  If the laptop is unable to switch to the home Toshiba screen then I presume that the BIOS has detected a hardware problem.
  In this case primarily the motherboard fails

  But if the laptop is able to spend the Toshiba start screen, the motherboard must be ok and only a 3rd device malfunction as HARD drive could cause this problem.

  Try to study a little

• my wifi is not working, and my troubleshooting does not start on my computer toshiba laptop? and he tells me that my bluetooth must be turned on?

  my laptop WiFi does not work and when I try to trouble shoot the problem he told me that my troubleshooting does not start and also, I get a message telling me that my Bluetooth is turned off?, but this problem all started when I tried to sing on the web and it keep going back to the sign in screen then I cleaned a lot and finally was a less able to get to my office on it but still no wifi and not able to start troubleshooting and still receive a Bluetooth message not on. ????? Help! Please, I beg you!

  Hello

  Thank you for writing to Microsoft Communities.

  Until we start troubleshooting on this issue please provides us with additional information by answering a few questions below, this will help us better solutions to the problems.

  1. What is the brand and model of the computer?

  2. what exactly happens when you try to connect to a WI - FI connection?

  3. you get any error message?

  4. are you able to connect to the Internet by cable?

  5 are. what store you referring?

  6. what operating system is installed on your computer?

  7. the problem occurs in safe mode with networking?

  Please go ahead and follow the steps mentioned and later a update on the State of the question.

  If this is a recent problem, then you can try a system restore to Normal mode or safe mode and see if it helps.

  Note: When you perform the system restore to restore the computer to a previous state, programs and updates that you have installed are removed.

  To run the system restore, you can see the following link.

  How to repair the operating system and how to restore the configuration of the operating system to an earlier point in time in Windows 7:

  For Windows 7: http://windows.microsoft.com/en-US/windows7/System-Restore-frequently-asked-questions

  For Windows Vista: http://windows.microsoft.com/en-US/windows-vista/System-Restore-frequently-asked-questions

  How to restore Windows XP to a previous state: http://support.microsoft.com/kb/306084

  Note: When the computer is in safe mode, System Restore does not restore points. Therefore, you can not undo a restoration you performed when the computer is in safe mode.

  Reference: Wi - Fi and in Windows network connection issues:
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Please follow these recommended steps and post if you still experience the problem.

• I have a Toshiba Satellite A85 with XP Home Edition series. Windows does not start. At startup I get Toshiba logo then a black screenwith cursor upper left. Can I save it?

  Toshiba Satellite A85 Celeron with XP Home edition. Windows does not start. I have Toshiba logo screen, then it turns into a black screen with the upper left corner of the cursor. I have the recovery disk. Is it possible to record HD without re-formatting and losing all data?

  Thank you;

  Lobo77

  If you run the Toshiba recovery application, you will lose all your data.  As indicated in the warning, this application will restore the computer back to wherever it was when it was first delivered by the factory.

  Without other complementary diagnostic information, it is difficult to determine what is happening.  Pressing the key (do not hold) of F8 beginning immediately after that the sequence of power should bring you to the Advanced Boot Options menu.  Try again then press repeatedly the key rather than pressing on and now.

  The recovery CD Toshiba, you have probably does not allow a "repair installation".  Contact Toshiba to see if they will provide you with a suitable CD.

  Given the fact that you can get a useful place when you start with the Toshiba Recovery DVD, my guess is that the computer is OK but that the hard drive has failed - or maybe more likely - the startup information is damaged so that it does not start.  If you have access to a computer equipped with a burner, download and create a bootable Windows CD.

  There are a number of available bootable CD which include various recovery and diagnostic tools.  You'll have to do some research to find out how to use the tools.

  Ultimate Boot CD 4 Windows
  Ultimate Boot CD
  Hiren BootCD

  If you feel overwhelmed by the tools and I just want back the data, and then use the Toshiba Recovery DVD, make you a Knoppix CD and use this key to your data, preferably on a network connection.

  If all this sounds like too much for you - and there is no shame in admitting that--take the laptop for a good local computer repair shop (not a type BigBoxStoreUSA or rather GeekSquad) and ask them to check it out and make sure to recover your data before anything else.