Touble router settings E900

Similar Questions

• Able to connect to the Internet, but not be able to access router settings

  I can connect to the Internet fine, ping works, but I can't connect to the router settings.

  Specifications

  • Router IP: 192.168.1.1
  • IP address: 192.168.1.150 USING static IP
  • Browser: Safari
  • Error message: Safari cannot open the page because the server dropped the connection unexpectedly.
  • If you need a card, leave a reply!

  Hey Harpo1! Try to access the configuration page using a computer connected to the router. If it does not connect to the page, reboot the router and use a different web browser could help. You can also try to temporarily unplug the modem and see if you can access it.

• Need to know how to reconfigure the router settings

  Hi - I was on the phone with technical support for an hour before, they told me they couldn't help me unless I paid or bought a new router.  Isn't an option for me financially so I hope someone can help.  :-(

  My cable signal came out very briefly, probably for 5 to 10 seconds.  When she came back, my router not working.  I jumped through all the hoops reset that work normally, but nothing has worked this time.  The tech guy said that I need to reconfigure my router settings.  I don't know how.  Can anyone here help me?

  I am running Windows Vista and the router is a Linksys E1000, version 2.  Is there a page on this site that tells me what to do?  I could not find.

  I thank very you much for any help you can give me.  I'm desperate!

  Thank you for your kind reply.  I did some reading and found that if I reinstalled the router, that would take care of the problem.  He did, and I'm back online!  I appreciate your response however!

• Windows 10 devices cannot access the router settings (R6250) page

  So, after several hours of troubleshooting (reset the router, firmware flashing, try several devices) I think I discovered why I get the message '192.168.1.1 refused to connect': 10 Windows. All devices not - 10 Windows can connect to Settings page fine, but all of my Windows 10 devices fail and get this message. And on my laptop, it gets the message refused on Windows 10, but when I rebooted the router and tried a linux live usb on the laptop, it connected to the page of the parameters very well. So I think it's some kind of problem between Windows 10 and the router.

  Anyone has any advice on how to fix this? I need the settings page to run on Windows 10 as it is the main operating system I use.

  Thank you!

  Have you tried different browsers?

  Try turning off the Windows Firewall, temporarily.

• How to find my router settings

  router cannot find the settings

  Hello

  can you write a bit more about the problem?

  Short time - no matter what router are a universal device and you need to set this device by the settings of your ISP (Internet Service Provider) If you use this device to connect to the Internet. The installation is done through the WEB interface.

  LC

• I can't change my router settings

  When I type 192.168.1.1 in my address bar, my browser reports that it may not display this Web page. Yes, this is the correct ip address because I did ipconfig. Router Linksys Wireless-G Broadband Router WRT54G2 Wireless. Here is a link to settings

  Hello

  You can try to configure the router by plugging the Ethernet cable and check if you still face the question.

  You too, try using the Internet Explorer web browser to configure settings and check if the problem persists.

  Reference:
  Set up a wireless router
  http://Windows.Microsoft.com/en-us/Windows7/set-up-a-wireless-router

  For further assistance contact the router manufacturer or Internet service provider.

• Router Linksys E900

  Good afternoon, and pardon the interruption. My name is Raymond Johnson Jr. and I was just curious to know what the serial number for a router E900 was and where I could buy the product. However, I also try to find out if the update of the firmware has been on the product before I bought it. I'm not able to contact the service to the customer for any question, until after I buy the product, but it is not the same version so I found this kind of weird. Likewise, I use linksys for a long time and am in need to get the product for internet connection of my mother. Now, if the response does not know it's quite good, but I would like to know if I can pass the router for my mother. We thank anyone so assistance.

  P.S. When did this product come out or when it is launched?

  It's confusing because the E900 has been out for a long time.

  You can purchase directly from the site Web of Linksys.

• How to install the firmware for the router LinkSys E900 update?

  Hello

  I use Mac 10.7.5 and a few months back had bought E900 wireless router.  He has installed 1.0.03 firmware and I noticed there is a 1.0.04)is update.  I downloaded the update, which is a sync .bin file, but I don't have a CD burner, or access to a Windows machine.  How can I install the update of the firmware?

  Thanks,-Dave

  Just, simple, with your wired computer (never wireless) access the GUI of the router and perform the update of the firmware.  Just point to the .bin file and you leave.  Make sure you reset the router and reconfigure it once you're done hard.

• Help to find the router settings.

  I have a WRT54G V.6, and I need to give to zero because the password has been lost. In the reset guide, he says you make a note of the current settings, but I can't seem to do it without the password. Is there another way to find settings?

  I'm an online gamer, so my connection quality is extremely important.

  No, you must reset the entire router or remember the password.  The default password is admin with no user name.

• Could not save the WRT54G Router settings!

  Recently, I have reset the Linksys WRT54G Router because I can't get the page with a note to "CONTINUE", I used to have. I can also save the new setting. What comes out is a blank page. Pls help me. Thank you.

  This problem is usually caused by suboptimal communication between the computer and the router. The most common cause for this is a computer software firewall problem, but there are also several other possible causes:

  To view web pages of the router (and to solve problems "Cannot save settings"):

  You don't need an Internet connection. 'web Pages' of the router are integrated into the router.
  Use Internet Explorer, it usually works.
  JavaScript must be enabled.
  Use a computer that is connected to the router.
  In the non-working computer, temporarily disable your firewall software.

  Point your browser to 192.168.1.1, and then connect to your router. Your username must be left blank. Your password is "admin" (without the quotes), unless you changed it.

  If you use Zone Alarm, do a right-click on the ZA icon in the taskbar (bottom right of screen) then click on "Shutdown ZoneAlarm" and see if that solves your problem. If this does not work, try the following with Zone Alarm: open the control center ZAISS, go to privacy, then temporarily disable Ad Blocking and Cookie Control and see if it solves your problem.

  Some Zone Alarm users reported that the addition of 192.168.1.1 to their address list "of trust" solved the problem. This trick can also work with other firewalls.

  If you use Noton Internet Security with the add-on Pack, don't forget to disable the blocker and ad blocker. Some users have reported that they needed to uninstall all Norton Add-on Pack.

  If you can not get anything to 192.168.1.1 then perhaps this is not the address of the router. Go to 'Start' > all programs > Accessories > command prompt.
  A black DOS window will appear. Type "ipconfig" (with no quotes), and press the Enter key. Look at the "default gateway". It is 192.168.1.1? Point your browser to the 'default gateway', can connect you to your router.

  If the above fails, unplug your modem router, then try again. If it solves your problem, then you probably a "modem-router" rather than a regular modem. A report with this problem and also specify the brand and exact model of your modem (not router) number.

  If all above fails them, turn off your entire system, unplug it from the wall, wait a minute, then lights up, then try again.

  If all the above tips fail, then reset the default router: power down the router and unplug all the wires. Wait a minute. Switch on the router, let it fully boot (1-2 minutes), then press and hold the reset for 30 seconds button, then release the button and allow the router to reset and restart (2-3 minutes). Turn off the router. Wait a minute. To connect to a computer, cable, a router's LAN port. Initialize the system. It should work.

  If you still have problems, then you must download and install (or reinstall) the latest firmware for your router. After the update of the firmware, you must reset the default router, and then configure the router again from scratch. If you have saved a router configuration file, DO NOT use it.

• Supported on the Cisco RV042 router settings

  Hello

  Anyone know if these settings are supported on router CiscoRV042

  shared secret - authentication-

  -AES-256 / SHA1 encryption

  -IKE: Diffie-Hellman (Group 2)

  -Phase 1 IKE every 1440 minutes.

  -The phase 2 (IPsec) all 3600 sec (every hour) of IKE

  Thank you.

  These are all very standard parts of IPSEC.

  See page 45 of the

  http://www.Cisco.com/en/us/docs/routers/CSBR/RV042/Admin/Guide/RV042_V10_UG_C-Web.PDF

  Copied here

  IPSec configuration

  So that any encryption occur, both ends of a

  VPN tunnel must agree on the encryption methods,

  decryption and authentication. This is done by sharing

  a key for the encryption code. Key management, the

  default mode is IKE with pre-shared key.

  Overlay Mode Select IKE with pre-shared key or manual.

  Both ends of a VPN tunnel must use the same mode of

  key management. After selecting the mode, the

  settings available on this screen may change depending

  on the selection you have made. Follow the instructions

  for the mode you want to use. (Manual mode is available

  for VPN tunnels only, no VPN group.)

  IKE with preshared key

  IKE is used to negotiate Internet Key Exchange Protocol

  for Security Association (SA) key material. IKE use it

  Pre-shared key for authentication to the remote peer of IKE.

  The phase 1 DH group Phase 1 is used to create the SA. DH

  (Diffie-Hellman) is a key exchange protocol used for

  Phase 1 of the authentication before establishing process

  pre-shared keys. There are three groups of different premium

  length of the key. Group 1 is 768 bits, and group 2 is 1024 bits.

  Group 5 is 1 536 bits. If the network speed is preferred, select

  Group 1. If it is better to network security, select group 5.

  The phase 1 encryption select an encryption method: SOME

  (56-bit), 3DES (168-bit), AES-128 (128-bit), AES-192 (192-

  ILO) or AES-256 (256-bit). The method determines the

  length of the key used to encrypt or decrypt ESP packets

  AES - 256 is recommended because it is the safest.

  Make sure that both ends of the VPN tunnel using the same

  encryption method.

  The phase 1 authentication select a method of

  authentication, MD5 or SHA. The authentication method

  determines how the ESP packets are validated. MD5 is

  a one-way hash algorithm that produces a 128-bit

  Digest. SHA is a one-way hashing algorithm which produces

  a 160-bit digest. SHA is recommended because it is more

  Fix. Make sure that both ends of the VPN tunnels using the

  same authentication method.

  Phase 1 life time sets the duration of a VPN

  tunnel is active in Phase 1. The default is 28800

  seconds.

  Perfect Forward Secrecy if the perfect forward secrecy

  (PFS) is enabled, the IKE Phase 2 negotiation will be

  generate new key material for encryption of IP traffic and

  authentication, then pirates using brute force to break

  encryption keys will not be able to obtain future IPSec

  keys.

  Phase 2 DH group if the functionality of perfect forward secrecy

  is disabled, then no new key will be generated, so you don't have

  no need to adjust the Phase 2 DH group (the key for Phase 2

  will be the key in Phase 1).

  There are three groups of different main key lengths.

  Group 1 is 768 bits, and group 2 is 1024 bits. Group 5 is

  1 536 bits. If the network speed is preferred, select group 1.

  If it is better to network security, select group 5. You do

  no need to use the same group of DH that you used for

  Phase 1.

  Encryption of the phase 2 Phase 2 is used to create an or

  several IPSec security associations, which are then used to key IPSec sessions.

  Select an encryption method: NULL, (56-bit), 3DES

  (168 bit), AES-128 (128-bit), AES-192 (192-bit) or AES-

  256 (256-bit). It determines the length of the key used to

  encrypt or decrypt packets ESP. AES-256 is recommended

  because it is the safest. Both ends of the VPN tunnel

  must use the same encryption of Phase 2 setting.

  The phase 2 authentication select a method of

  authentication, NULL, MD5 or SHA. Authentication

  method determines how the ESP packets are validated.

  MD5 is a one-way hash algorithm that produces a

  Digest of 128 bits. SHA is a one-way hashing algorithm that

  produces a 160-bit "Digest". SHA is recommended because

  It's safer. Both ends of the VPN tunnel must use

  the same Phase 2 authentication setting.

  Phase 2 HIS life time sets the duration of a VPN

  tunnel is active in Phase 2. The default value is 3600 seconds.

  Pre-shared key that specifies the pre-shared key used

  to authenticate the remote peer of IKE. Enter a key of

  keyboard and hexadecimal characters, for example, [email protected]/ * /.

  or 4d795f40313233. This field allows a maximum of 30

  characters and hexadecimal values. The two ends of the

  the VPN tunnel must use the same pre-shared key. It's

  We recommend that you change the pre-shared

  Key periodically in order to maximize the VPN security.

• settings on the router for ITouch

  I have tried to connect my new ITouch with my home wireless, but will have many problems.  It does not accept the password.  I read some of the discussions, but there are so many things listed there.  Right now my router, a WRT54G, is defined as 64-bit WEP with a code.  What I read, I should change to a 128 bit and generate a key code for this.  If I do that, should I do something different for my laptop, which work very well with the wireless?  I won't spoil things, I'm not use to treat the router settings, etc..

  If you change the 64 to 128-bit WEP encryption, generate the password for you and use the 1 KEY to reconnect to the network wirelessly on your laptop.

  Open an Internet Explorer browser on your computer (desktop) wired page. In the address bar type - 192.168.1.1 and press ENTER... Let the empty user name & password use admin lowercase...

  Click the Wireless tab, click the wireless tab, the value of the 11-2, 462 GHz wireless channel, provide the unique SSID for the Name (not linksys) wireless network... and click on save settings. Click on wireless settings, advanced, change the tag to 75 interval, change the Fragmentation threshold to 2304, change the RTS threshold to 2304 > click 'save settings '...

  Now try to connect the i-Phone and check...

• Add DNS - network settings, the parameters of the airport or both?

  I didn't know there are 2 places for that - and I'm not sure that works best.

  Recently added 6.6.6.6 and 8.8.8.8 to try to speed up Web sites that have been loading slowly, as suggested these tips very. I have added in the network settings, but then recently realized that my extreme settings of the airport have a place for dns as well.

  I do not understand the difference.

  Your Mac setting only controls your Mac.

  The parameter to your Airport Extreme allows to set any device on your network.

  If you have only one device, there is no difference.

  But suppose that your family has 9 network devices: two Mac, a PC, a smart TV connected to Netflix, four smartphones for parents and children and an iPad. If you enter the DNS settings on your Mac, this is the only device that will use the DNS settings. But if you enter the DNS of your network (Airport Extreme) router settings, which becomes the default DNS for any device on the network that does not have its own DNS settings entered. You have only to change DNS setting once, not 9 times for all these devices.

  For all my devices that stay at home, I get the DNS on the router addresses, and the devices are all set to look at the IP address of the router to get the DNS so that all devices follow the DNS from the router configuration. For all devices that leave the House, I get the DNS preferred settings on those so that they will continue to look at my favorite, DNS settings even when they are connected to the network of another.

• Problems with AirPort Extreme and Qwest Modem/Router.

  I have a Qwest ActionTec 1000 DSL VDSL2 gateway and want to disable the functions of router wireless and those through direct AirPort Extreme. I know that in the Modem I have to disable the functions of addressing and turn them in the AirPort Extreme to avoid address conflicts, but what are the settings I need to change in both devices? And what is "A Transparent bridging" on the side of the modem?

  But what are the settings I need to change in both devices?

  Sorry, we can't help on the settings for the modem/router, because it would be a question of Qwest as to if this is even possible and if so, if Qwest will support this type of installation. Sometimes the ISP lock modem/router settings, and although it seems as if you can change the basic configuration of the unit, you can really.

  Yes, it is possible that another user of Qwest has done with the same modem/router you have and an AirPort Extreme... and may know the answer... but the chances of the person who holds this information also to see this post are slightly above zero. But, I guess it's possible.

  If the modem/router can be configured to operate only as a simple modem, then the next step would be to get your Mac connected directly to the modem to test the connection in this way. If Qwest is going to help you, they will do it no doubt with your Mac connected directly to the "modem" as well.

  Once you know the exact details of the PPPoE authentication to establish a connection, these parameters can be transferred to the AirPort Extreme and removed from your Mac. To do this, you reset the AirPort Extreme back to default and then put settings in place again. The installer should detect the PPPoE connection and then ask for your login information.  After this, the correct settings apply to AirPort Extreme during the installation.  You can still use the same wireless network name and password you used before if you wish, or set up a new network name and password.

  PPPoE on the routers of the airport, at least in my experience, was not a reliable way to connect when I tried this in the past, but you don't really know how well... or even if... it will work until try you it. Unless you really want the airport to distribute IP addresses to devices on your network, things would be a lot more simple if you went ahead and used the modem/router "such what" and then let the airport works in Bridge Mode to transfer information in connection with network devices.

  When you have the modem/router converted to act as a simple modem and made a successful connection using your Mac connected directly to the "modem", post back and we can help with the configuration of the AirPort Extreme if you need more advice.

• Router WLan disabled but I need ACTIVATE WLan

  After how many years to have wireless connectivity to our router to my laptop - my father-in-law has suddenly decided to turn it off, forcing me to use a direct connector of the router to my laptop for internet access! I need help!

  Is there a way to retrieve my wireless internet!
  Basically, I can't get wireless connectivity more - in order to access internet, I have to use a cable that is plugged directly into the router.

  In addition, the icon at the bottom of the computer screen which is usually a mini computer screen that flashes - has now changed to TWO screens of minicomputer that flash?

  I think it has something to do with a toshiba - called config free program. IM on a limited user account and I see it has disabled the wireless network connection - does that mean that I have to enter the admin account and then change somehow?

  Help.

  > after how many years to have wireless connectivity to our router to my laptop - my father-in-law has suddenly decided to disable

  I think you have misunderstood something if the WiFi is turned off in the settings of the router, then you will not be able to receive WiFi signals using the laptop.

  You must activate the WLan in the settings of the router (must read the manual of the router).

  Once the WLan has been activated and configured in the router settings, you can turn on Wlan on a laptop and can configure the Wlan card settings to make the connection.