Touch cell phone envy: white screen

Similar Questions

• Inserting a Flash Drives and cell phone causes blue screen - stop 0x3B

  Original title: inserting a few Flash Drives, but not all, and cell phone causes a blue screen of death

  Computer Dell Inspiron 518 Intel core 2 quad, 6 GB memory, office 2 years.
  HP Vista 64-bit, Service Pack 2, updated version 6.0.6002 fully implemented.
  No change to HW or SW immediately before the first detected failure, but the USB port which is not often used.
  History - off Ready Boost after a short experience and installed months ago driver and card Renesas Electronics USB 3.0.  This driver has been disabled through all of this, but I've not yet physically removed the card.  Disable ready boost was simply to stop - no other instructions not found for removal.

  Anitvirus BitDefender and Malwarebytes scans are both clean.

  A flash drive works fine, but three others cause seconds blue screen of death after installing into any USB port.   Bought a new flash drive and it also causes a crash.  Found cell phone also gives BSOD.  All work fine on another computer.  USB is currently led printer, external hard drive, digital camera downloads and keyboard/mouse very well.  Tried both USB ports with the same results and back and disconnected all other USB devices except the keyboard and mouse.  Remove and reinstall all USB drivers (6) one by one (the 1CH9 Intel USB controllers host family) and USB controllers enhanced (2);  also storage device USB and device drivers USB Composite and façade drivers card reader.  After each new facility, any 'bad' flash player causes immediate crash.  'Good' flash player's Centron Centon Pro 8 GB and one of bad flash drives is one attached PNY 8 GB, another a San Disk.  I think, but I don't remember, that the 'good' flash player was installed for Ready Boost test.

  Unable to find a failure code or no trace of several accidents in the problem reports.   Here is all the data of failure that I could find:

  0x0000003B
  (0x00000000c0000005)
  0xfffff8002a8db87
  0xfffffa601

  I'm puzzled.  Thanks in advance.

  Tom

  Hello

   
  You must update the BIOS (Basic Input Output System) and the Pilots of the Chipset using the computer manufacturer.

• I installed the touch cell phone Verizon de Cosmos software to download the photos but cannot find them

  Charge phone Verizon Wireless Cosmos Touch software.  But don't know if the images download because I can not find them!

  Thank you.

  Hi Glenda,

  You must contact Verizon for extra support.

  Verizon support

• HP ENVY 15j140na: new cell phone Envy 01/05/2015 saying the Windows I use is invalid for activation

  I got this laptop for two days, I already had to do a recovery

  And now he tells me that

  The Windows product key you typed is invalid for activation

  Buy a new product key online

  Type a different product key

  Contact Microsoft to help solve this problem

  I already phoned HP which was one was time so I won't do it again once.

  First of all I've never typed in any product key for any software I also powerDVD telling me what he

  working only with authorized material.

  I better call my Bank and start a chargeback, or continue to try HP in the hope of obtaining a product key

  to use the £500 + laptop that I just got from them.

  I have two days left until this laptop doesn't help that day, it will be sent for a full refund

  (if they like it or not)

  I sent the laptop now

  Why can you not get a good laptop more than 4 years ago, you had more to choose from than you do today

  It's a shame.

• HP Envy M6: Screen HP Envy white M6

  I have a laptop HP Envy M6-1125dx, yesterday morning it worked perfectly, so I let it idle for like 20 minutes only to return to a blank screen, tried restarting several times with no luck, google for solutions and so far I tried all the solutions given. Windows + B + Power key, tried the Bios using a flash USB, reset hard drive recovery solution I tried but it still shows a blank screen. Help, please.

  Hi @Mr_Dee,
  
  I hope you enjoy your visit to the HP's Support Forums. I understand that you have a problem with a white screen. I'll be happy to help you.

  Please see the document for computer does not (Windows 10).

  Please keep me informed of the progress of things.

  If you need help, let me know and I will gladly make all that I can to help you.

  Please let me know if that solves the problem by marking this post as "accept as a Solution.
  To simply say thank you, click the Thumbs up below!

  Thank you.

• ENVY 110 e-all-in-one printer can't find my cell phone to scan

  Whenever I try to scan to my laptop, it not only can not find. I have a HP laptop and it was working fine before, but now he can't seem to find it. I ran printing HP and doctor Scan and he said that checked everything. I opened the scan on the program function on my computer and it opens. They are both on the same network. I had the same virus protection and firewall settings since the time that I bought it. I honestly me nothing but problems with this printer since I bought it. Just after I got it, it loses the connection to my router and reset the IP address. One of the technicians helped me set up a static IP address which helped a bit, but then he did it again. So basically, now I have to reset my router and the printer almost everytime I want to use it. Another person, I talked about the cat says that my router has to be on channel 11. I made sure it was 11, but it still does the same thing. But anyway, it is connected to the network now. It's wireless printing and it is scanning to my other computer, but it does not find my cell phone. Is there something I can do? Should I uninstall and reinstall the software?

  Hello Sweetmuffins21,

  Please perform the below mentioned steps that should solve the problem.

  • Double-click the printer icon. HP printer help window opens.
  • Under the section of the ANALYSIS, are looking for to manage scanning to computer and click on it.
  • Then click on the button ACTIVATE.
  • Now try scanning using the front of the printer, it should work.

  Kind regards
  Jabzi

  Give Kudos to say 'Thank you' by clicking on the White Star under my name.

  Click on 'accept as Solution' if it has solved your problem, while others may find it.
  I work for HP

• Hello I use adobe reader in android mobile and do not run correctly does not touch NOT open turns on the edge of the cell phone android. The importance of the issue is 5.6. what I can do... ??

  Hello I use adobe reader in android mobile and do not run correctly does not touch NOT open turns on the edge of the cell phone android. The importance of the issue is 5.6. what I can do... ??

  [TWO double message deleteds... post the same question more than once is confusing... MOD]

  [This is an open forum, not a direct line to Adobe support... you have to wait a response]

  Thank you for your information, but the last update was solved the

  problem... Thank you...!!!

• HP ENVY laptop - 15-ae101nx: when I put my cell phone battary trolling the games what should I do?

  When I put my cell phone battary trolling the games what should I do?

  Games run perfect when I put plugged in, but when I play on games battary became late?

  Help me.

  Hello @XxHamodyGamerX,

  Thank you for visiting the HP Forums!  You have come to the right place to ask questions, find solutions and get help from others in the community!

  I read your post on game performance below of your DESIRE for computer laptop-15-ae101nx then on the battery and wanted soft hand for you.

  This document should take you in making adjustments to the different systems of power supply on the system. Battery power, it is probably defined by default on energy saving , which will reduce the performance of the system in order to save energy and extend the time between charges.

  Microsoft also has very detailed information here on different powers available plans.

  Please let me know if this information helps you solve the problem by marking this post as accept as Solution, this will help others easily find the information they seek.  In addition, by clicking on the Thumbs up below is a great way to say thank you!

  Thank you.

• Qosmio F10; White screen at startup

  About a week ago my laptop starts with the screen does not. Strange! Everything seems to work fine, power lights on the hard drive whirring away etc but nothing Visual. After having read the manual I touch FN key and f5 and the screen appeared. Now there is however a noticable difference in the quality of the image. (Fonts appear blurry) Each time cell phone lights up I no longer get the graphic qosmio that appears and the screen are black for about 30 seconds before desktop appears. I also noticed that when I ran the Qosmio presentation a white band about 50 cm wide appears upright to the bottom of the right side of the screen that looks like a vertical taskbar. Notepad is just 10mths old still under warranty and with "very little high"especially used for wireless internet access. Any help would be welcome, thanks in advance.

  Your Qosmio seems mode clone (tv + tft).
  Right-click on the desktop. go to display properties. Last tab on the right. Select the proper resolution.
  Then press "Advanced" on this tab. Go to the tab 'Geofrce FX5700' select Nview, then select 'standard' instead of Clone. Press on apply.
  It should solve your problem.

  Or easier, I've just thought about it, press Fn + F5 until the selection is only your TFT screen.
  Later,.

  Alcahest

• Calendar on iPhone is frozen with a white screen

  I have an iPhone with iOS 9.2.1 6.  The application of calendar on the phone displays a blank white screen. I can not activate today, calendar, Inbox, or < March.  I tried to add to an entry when the problem occurred. I saw a possible fix in Kelby iPhone book, 6th edition, but is reluctant to try because the edition of this book does not include the iPhone 6.  The book is just up to the iPhone 5. PollyCB

  'Kill' the session by double clicking the home button - and slide up on the calendar app

  This should allow you to get

  If that is not - restart your phone - without data loss is incurred

  Restart your iPhone, iPad or iPod touch - Apple Support

  (1230)

• I forgot my password while my wi - fi and cell phone are disabled

  Hello my dear it

  I forgot my password so I searched in Internet sites and found 3 ways for restoring my iphone but unfortunately:

  1-i have my Apple ID user and pass, but the wi - fi and cell phone are off and I clouldn can't disable the password to icloud.

  2. I did recovery about 6 times but unfortunately it did not work.

  What should I do now...?

  Please answer me... Please...

  sincerely

  Ali

  • Connect your device to your computer and open iTunes. If you don't have a computer, borrow one from a friend or go to an Apple Store or service provider authorized Apple for help.
  • When your device is connected, force restart it: press and hold the sleep/wake and home for at least 10 seconds, and only release when you see the Apple logo. Keep until you see the screen in recovery mode now.
  • When you see the option restore or update, choose update. iTunes will try to reinstall iOS without erasing your data. Please wait while iTunes downloaded the software for your device.
    If the download takes more than 15 minutes the device out of recovery mode, you must repeat these steps and choose restore instead of update when you return to this step.
  • After the update or restore is complete, configure your device. If you have backed up your device with iTunes or iCloud and you need to restore your device in step 3, you may be able to restore from your backup during installation.

  Contact Apple Support so you can not update or restore your device with the recovery mode, or you cannot use the recovery because of the broken or stuck buttons mode.

  If you are unable to update or restore your iPhone, iPad or iPod touch - Apple supports

• White screen then the message ' selected boot device has failed.

  After a normal shutdown last night, that my cell phone went straight to a white screen on back when I turned on.

  I tried to plug and unplug, take out the battery and connecting it to a TV with a HDMI which did not pick up anything.

  After turning off the power on and off several times, there is now a white dash in the upper left.

  I let him down for about 20 minutes before a message saying "the selected boot device is a, press ENTER to continue" that turns off the computer.

  I had the computer 4 days if shouldn't them be anything malfunction already.

  Any help would be appreciated!

  GabbyBlag

  Hello;
  
  Let me welcome you on the HP forums!
  
  I read your post on startup problems and wanted to help.

  You should not have problems with a PC this new.
  
  My suggestion is that you contact the HP customer support to see about maintenance and options at your disposal under warranty replacement.  If HP is unable to repair it, then you should be able to insist on a replacement - no charge!
  
  If you live in the United States or the Canada, details are on this page: http://www8.hp.com/us/en/contact-hp/phone-assist.html#section1
  
  If you live elsewhere, contact details are on this page: http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
  
  NOTE: once you get through, stay on the line until you are finally able to talk to someone ' one - it can take a while!
  
  Good luck
  
  I'm a volunteer and I do not work for, or represent, HP.
  ========================================================================
  If you feel that my suggestions helped you, please click on the thumbs-up symbol to say thank you!
  
  If they helped to solve your problem, please click 'Accept as Solution' to help others find similar information.

• a laptop with a Wi - Fi hotspot wireless can use cell phone apps?

  a laptop with a Wi - Fi hotspot wireless can use cell phone apps?

  Firstly, your computer probably uses an Intel or AMD processor.  Only programs using the Intel instruction set have any prayer running on your PC.  A cell phone probably uses an ARM or Tegra processor with a set of instructions completely different.  There was no physical way for a cell phone application run on a PC.

  Second, your cell phone likely does not implement any type of SMB shares, so there is no way that a PC will be able to see it as a device which can be accessed on the network.

  Thirdly, the display on the PC hardware is completely different from that of the phone.  The application on the phone will include the PC hardware and be able to communicate with the PC drivers in order to interact with the PC hardware.  It is simply not possible with a cell phone application, written for the touch screen.

• White white screen on Dell Inspiron 15 - N5030

  Hello world

  I am trying to solve this problem with my wife's cell phone and its really frustrating. His Dell Inspiron N5030 and it's just more than a year. Unfortunately the 1 year warranty expired and this problem started to arrive in 2-3 months. The problem is, when you start the laptop, it has a complete blank white screen. I read quite a number of messages autour and many have suggested that it is usually a video cable connection, or a bad video cable of the lcd screen or a problem with the motherboard. I will explain the steps that I've done so far and I hope someone here can guide me on what I can do next to fix this.

  First of all, when this problem started happening, it was very unpredictable. Which means that, sometimes, the laptop starts fine but sometimes white screen appears. But as the weeks went by, the white screen begins to appear more frequently, and now it appears all the time. That's what I found so far:

  (1) when you connect an external monitor, the external monitor works fine. The strange thing is, sometimes when I connect the external monitor, disappears from the white screen of the laptop and the screen lcd laptop starts to work again. I got this as a workaround for some time. Whenever the white screen appears, I connect the external monitor and remove it when the screen of the laptop working again. But eventually it stopped working as well.

  (2) when the white screen started coming all the time, I noticed that the problem goes away when I remove the outer cover of the screen. (the black frame around the screen that can be removed by pulling the top of the screen).

  (3) last week, I removed the LCD and taken apart to see if there was any loose connection at the back. I noticed there is no loose connection and the inverter was very good as well. However, I noticed that the black (video cable) cord that connects the back of the lcd screen to the motherboard was sorta stuck around the hinge area. I corrected this cord so its properly seated and made sure that the outside frame does not grow this rope to the hinge when I set everything again. When I did this, the laptop started to work very well for next week without problem but now the white screen started to reappear!

  So, based on what I've seen, I think that the cord is blocked around the hinge and therefore to cause this problem. But I'm not a techinical person and don't know if its correct. It's just a guess... So I don't know what I'm doing then? This means that the video cable is drunk or is just blocking on the hinge at the origin of this problem? What I need to change the complete lcd video cable or is there another solution by moving this cord away from the hinge to fix this from happening? What I try next?

  I appreciate all help and thank you for taking the time to read my post.

  Hello world

  Here's an update on the solution of this problem with screens white white. I finally fixed it, and this time I know for sure that this problem is definitely solved.

  First of all many thanks to "randypittes" for first of all the solution and share with all the world. Much obliged!

  After setting up with this problem white screen for several months, I finally bought the "LCD video cable" on ebay and he succeeded. Its been 2 weeks now that I changed the cable and the problem re does not! I wanted to give him two weeks first and see if the problem comes back again until I jump into conclusion and now that my laptop works perfectly again, I know for a fact that this problem is probably resolved.

  So, those of you experience the same problem, do the same thing. First of all start by replacing the LCD video cable and this should fix the white screen issue. He me $20 encrypted only on ebay (including delivery in sydney) and it is a much cheaper option than to try to replace the screen itself. If this does not work for you, then you can look into other options. But I would say, this solution should solve most of the white screen issues you may encounter.

  Here is a guide that I put in place about how I went to change my video cable in my laptop. I don't know that it can be useful to other beginners like me:

  Step 1: first of all, make sure that first download you the manual of your laptop. Google simply your laptop model and you should be able to find the manual for it on how to replace its parts, etc... It's really convenient when getting started.

  Step 2: Check out this video on how to remove the screws around the LCD and how to get to the video cord to the back of the LCD:

  cs_setInnerHtml ('video_8efdced1-828d-4463-b632-022776eb4f65', ");

  Step 3: Check the downloaded Reference Dell manual and see how to remove the screws on the laptop base and how to remove the:

  (a) is based

  (b) keyboard.

  Step 4: once you remove the palmrest and keyboard access to the motherboard with the video cable is connected.

  Step 5: Replace the cable and reassemble everything to the way it was.

  It's her! And good luck to all! You need... :-)

  without a doubt

• HP EliteBook 840 G1: GPS Module - find cell phone lost / stolen eventually

  Greetings.

  One of our new cell phones seems to be missing and we cannot find it within the company.

  Either this is move - or in the worst case scenario, stolen.

  As these laptops has a GPS module, can we track down with the help of HP?

  No third-party tools when installed from our part for this.

  Best regards

  Paul.

  Dear customer,

  Welcome and thanks for posting your question on the Forum of Support HP

  Answer to your question is 'NO' as we cannot follow the specifications

  What you can try to:

  1. call HP Technical Support and report this problem

  2. get a case for your conversation with the representative number immediately

  3. Please find the reception of your laptop, scan a copy of it and send you a copy of it in your Inbox

  4. Please contact the nearest Police station and make a complaint about your laptop is stolen

  5. delivery of the hard copy of the invoice of your laptop the cops

  6. keep in touch with cops and tracking to get an update as and when you need

  Note: HP is not responsible for any loss of data or information on your laptop because there is no way to track your

  Laptop

  Hope this helps, for other queries in response to the post and feel free to join us again

  * Click on the white button on the right to say thank you Thumbs Up *.

  Make it easier for others to find solutions by checking a response "Accept as Solution" if it solves your problem.

  Thank you

  K N R K

  Although I am an employee of HP, I speak for myself and not for HP