TouchSmart IQ816 AC Power adapter is dead, which Part do I need?

Similar Questions

• Power adapter lost T60 - which is the right one?

  Hello people,

  I lost the power adapter for my lenovo t60.

  How can I find out, what voltage I need

  for this special model of lenovo?

  On the back is written:

  ID: 1951VBM

  Thank you very much

  The T60 comes with adapter 65W or 90W. 90W is required for machines with dedicated graphics processor. Your model contains graphics intel, so it would be originally came with a 65 Watt adapter, but either will work.

• PC laptop battery not charging but laptop works with the power adapter... which is wrong

  My power supply battery icon States attached but do not load, why

  Hello

  Download and run the test utility of battery pack available on the next page and see if it reports any problems with your battery.

  http://h20239.www2.HP.com/TechCenter/battery/battery_ts.htm

  Kind regards

  DP - K

• Defective power adapter?

  I've had my laptop for a year or so now, working fine until recently. I noticed that my adapter has begun to make a sort of pulsating squeal noise, now it does not power the laptop at all, no lights, nothing. All I get is an annoying squeal.

  I unplugged the laptop to see if it was the power adapter or the laptop and he continued to scream so I can exclude the laptop. Is this to say that I need a new adapter or could the card be defective? I tried different outlets with the same result.

  Has anyone else had these issues?
  Any help is appreciated,

  See you soon

  Ray

  > I noticed that my adapter has begun to make a sort of pulsating squeal noise, now it does not power the laptop at all, no lights, nothing. All I get is an annoying squeal.

  Maybe the power adapter is dead and you need a new.
  But understand that it very difficult to tell exactly what evil without any control of the laptop
  In any case try to plug a compatible AC adapter and check if the laptop turns on.

  Good luck

• r8500 Power adapter needs to be replaced

  Hi guys,.

  Unfortunately, my puppy has decided to go into my computer room and causing havoc with power cords (didn't hurt fortunately but it has decided to start chewing on large parts of the adapters, only good side of things, it's that he didn't have a wee on it!)

  Anyway, I can't find a power adapter replacement online for this specific router. Is there any place I could find an or can support netgear help me buy another (I can't be the only person who needs a replacement power adapter). I don't want to get the bad either and short-circuit this unit.

  So if there is someone who knows where to find one, or could help me to find the right person to netgear to connect with I would really appreciate it!

  @ifixidevices Like E - Bay is a not authorized reseller, consider buying a new power adapter.

  The part number is 332 - 10631-01.

• Cinema poster 30 '' Dead - could this be the power adapter?

  Monitor: Cinema Display 30 ''

  Computer: Connected to a MacBook Pro mid 2012 of the retina with a 2.6 GHz Intel Core i7, 16 GB of RAM.

  Graphics card: NVIDIA GeForce GT 650 M 1024Mo

  I got the screen of cinema since 2007. Used with a tower for the first five years, replaced the tower with a MacBook Pro in 2012. The CD went with the laptop using a bolt of lightning > DVI adapter for about 3.5 years, worked ok. Finally, the Cinema Display monitor everything went black. The LED in the corner is always on when powered. I can still use the power on the CD button to turn the monitor on/off, standby system etc. the MBP still sees the CD in monitors when the adapter is plugged. The CD can still push USB devices. But there is no picture, no matter what I do.

  Finally carried the old tower outside and connected to it, just to see if it was something with the MBP the CD. Same results, no image.

  I noticed that the power adapter brick remains cold. If it's just that bad, and I could replace it for a relatively low cost? I see the price of $150/200 on Amazon. Don't want to waste his time with that much more, it's a 9 year old monitor. But I really loved and I want to see if I can get pulled upward again.

  Thank you.

  Looks like either the back lit display is on the way out (you can tell if the monitor is nothing display by shine a very bright light until the front screen and see if you notice any displayed video), or the display is not simply detect the output signal of your GeForce card. I have a NVidia GTX 770 and one of my 3 cinema Display is sometimes the same thing. I end up having to unplug the screen for a few seconds, use WIndows to detect the display, plug the monitor back in and detect the display again to get any video to show on screen. It is intermittent but sometimes quite stubborn. Good luck! If you have two monitors, you can use work to see whether or not your cinema is even detected. If it is, but the screen is always black, it is likely, that you will need the spare parts for backlight.

• A Magsafe 85w power adapter would be detrimental to my MacBook Pro (13-inch, mid 2010)

  Hi all!

  I have a MacBook Pro (13-inch, mid 2010, 2.66 GHz Intel Core 2 Duo).

  Well, after years of abuse, the thinner rope (which connects to the Macbook) began to tear. I tried to drag an above shrink wrap to fix and make it last a little longer, but now I find myself stirring the rope around so he can start loading.

  in any case, I found a company after-market on Amazon called Supsun making (link below) and recently purchased a. He said that going to work with my Macbook, but I think not even check what power mine use and after he woke up, I found out mine originally a 60w.

  Will this hurt Magsafe Supsun 85w power adapter my mid 2010 13-inch Macbook in anyway?

  I thank you for all your comments!

  Link to Supsun adapter that I bought on Amazon:

  F8 & PSC = 1 https://www.Amazon.com/GP/product/B01IP3YNA6/ref=oh_aui_detailpage_o00_s00?IE=UT

  I, personally, look at the price difference and ask myself I'd be sad if I saved money and things did not work well.

  Review, carefully, then users of the product review.

• NVIDIA Quadro: I plug 6-pin power adapter or connector 8 pin?

  I am trying to install my graphics card Nvidia Quadro 6000 on a HP Z820 with a PSU 1125W

  The Quadro card: 1x8pin auxiliary power connector and power connector auxiliary 1x6pin.

  My questions are

  1. in the connection of my power adapter, do I plug the unit into the 8 pin or 6 PIN auxiliary connector?

  2. where can I connect the other end of the power adapter?

  3. the power adapter must be a HP one or can I use any brand.

  4, if it's HP, what is the part number

  I would appreciate help on this.

  Vinny

  Edit: Here is this link related to this issue.  It goes also to other topics with excellent similar information:

  http://www.TomsHardware.com/reviews/power-supply-specifications-ATX-reference, 3061 - 12.html

  First, it is important to know that there is another interface "6 to 8 pins" which is a feature of power-for - motherboard power ... you don't want that, sure, and connectors plastic is having different shapes.  You can see that he has 4 yellow wires (usually the supply wires) and would not have the sequence of correct wiring of a PCIe 6 to 8 pins supplementary power converter:

  

  I don't know the show, too, is not what you want.  This looks like an 8 pin to two adapter 6 pins.  You want a 6-pin to 8 pin adapter.  Is attached another picture of the nVidia type tells you to do.  If you look at the hyperlink at the top of this post you will find the wiring of 6 pins on 8 wire and for your project, you will probably want to follow the advice of nVidia for best results.  There is power to the ground and 'sense' son to all be correctly connected to the adapter.

  There is also some PCIe additional adapters that allow you to convert several sheets supply 4 son "molex" grouping in a single 6-pin PCIe or connector 8.  It is best to not do this if you have a power with official ones built in.  Your the fact, and to check the manual, it looks like your top rated power supply has 3 of these auxiliary PCIe power cords (G1, G2 and G3 will be printed on the side of the end of your 3 card).  On the other hand, offer reduced rated power of the Z820 has only 2 additional PCIe (auxiliary) cords supplied by it.

  I don't know if you are forced to use a good 6-8 converter or could if away with plug 6 pin right in the correct position on the plug 8 pins of your videocard directly, according to article of the hyperlink.  I, personally, would get an adapter.

  EDIT: Here is a picture of two ends of what is supposed to be a PCIe 6-pin supplementary power adapter PCIe 8 pins.  The first and third power pins 6 pins are officially DC 12v (some references have each of the first 3 pins being 12vDC) and subsequently, the rest are supposed to be a 'sense' or earthed.  When I look at the plug 8-pole end wiring I do not see a ground wire or ground jumper coming to pin 8.  I would not recommend it, unless I'm wrong about his son:

  

• Satellite M300 guarantee for a power adapter broken?

  I have some problems with getting a new power adapter.

  First of all, I don't know if the warranty covers the power supply.

  Second, even if it does, the warranty (I bought a Toshiba Satellite M300, which came with a 1 year warranty, about 360 days ago) may expire before I can get the card sent to a Service Center for repair of toshiba in Victoria (I live in Tasmania.

  Thirdly, I tried to call until the call line of Toshiba which was given to me by the store, I bought the laptop, but after having pierced the numbers to get a representative human (and I tried several combinations) I had absolute silence from the other end of the phone, so I can't get all the answers to all your questions and I have no idea where to send the broken adapter.

  So wherever I need to send my adapter, it can be sent at the time, I will be actually return a new power adapter and is there anything else I should do to get it?

  Hello

  First of all:
  Yes, the power adapter is covered by warranty (if the warranty is valid) as the entire notebook

  Second:
  The standard warranty is one year. So if your warranty is still valid you should get in touch with a local ASP (certified partner) in your country and have to ask for help.
  The right ASP can be found [here: http://eu.computers.toshiba-europe.com/innovation/generic/ASP_SUPPORT]

  Third:
  See point 2, you must contact a local ASP.

  Welcome them

• Question about Satellite A30-power adapter

  Hello

  I own a laptop Satellite A30 and my charger just died. I have looked on the internet to buy a new one, but can not find the same model of the same brand (delta ADP-90FB REV electronics. (E) and having trouble finding something on the site Web of Toshiba.
  I found some Chargers compatible with laptops Satellite A30 on another site, but they are quite expensive (about £55). Another less expensive option?

  Thank you

  Thomas

  Hello

  Believe me: it s better to use than stuff unnamed original equipment. On the one hand, you win money and if your machine is broken due to a power adapter that gives your machine
  a wrong voltage or whatever.

  I had a great experience with my tecra 8100 a few years ago:

  My old AC was broken, so I bought one in a store, which has been declared as "corresponds to 100% and blablabla".

  Cost: $ 37

  After a while my machine freezes sometimes and for a day-> no boot.
  Then I gave my machine to fix after they have made their diagnosis, they asked, what sort of AC, I used. Heh? They explained to me, I used the AC adapter was not a constant voltage,
  If some capacitors smd-says 'goodbye '.

  You can save money, but give you him another side, believe me.

  Welcome them

• My Satellite goes into battery mode despite being connected to the power adapter

  Y at - there anyone out there who can help me, please!

  I bought a Satellite a couple of years ago which worked well for a while - however, it has started to overheat a lot and kept stop without reason. After many searches on the net, I discovered that the fans were very likely blocked with dust? After you clean the laptop worked like a dream and as a Bunny happy I was!

  However, now a new problem has been its ugly reappearance - for some weird reason the laptop suddenly, without warning, past in dominant mode of battery despite being connected to the power adapter? He refuses to "acknowledge" that the adapter is plugged drains the battery quickly and then stops?

  I tried once more looking for an answer and it seems that I am not alone in suffering from this problem? I read that it is perhaps a bad connection between the adapter and the motherboard, but it would be expensive to fix? Others have said to try a new adapter, but I tried from another laptop and it still happens? I hesitate to implement local repair because sometimes, this problem may occur after half an hour and other times, that won't happen for hours and hours and it is difficult to explain the problem?

  There seems to be no rhyme or reason, but to crazy me on a regular basis!

  HI Deb,

  It is a common problem and can have several causes. The most common are a common defective soldering on the motherboard (where the socket is attached) and it can also be caused by a bad connection between the AC plug (at the end of the cable) and the socket on the laptop.

  Unfortunately, the standard response from most repairers is just to replace the motherboard, probably because it's faster for them and produced more revenue that comes to fix the connection.

  I solved this problem on my SA30 by pinching the cable ca to the back of my laptop in order to prevent any movement or tension on the connector. Unfortunately this will not help if the socket is already damaged, but it can reduce the incidence of the problem to occur.

  Kind regards

• Spectrum for computer laptop 13-v051na: connect more capacity power adapter Message

  After starting, I get the following message. "For maximum performance, connect a higher capacity Power Adapter.

  The power adapter I use is provided in the box with the notebook. So I'm at a loss on what to do and do not understand the impact with an adapter in addition low capacity.

  AFAIK, the ability for the laptop power adapters are not in the HP store.

  Details of the laptop;

  Spectrum of HP for computer laptop 13-v051na, part number; F6P95EA #ABU

  (Note that this laptop is a variant of PCWorld/Dixons cell phone spectrum HP Ref. 13 - v001na F4W33EA #ABU)

  Details of the charger supplied with the notebook; (markings on the charger)

  Power supply for charger USB - C;

  Model; TPN-CA02

  HP part No.; 848067 002

  HP Spare; 848293 850

  Entry; AC 100-240V 1. 4A

  Exit;

  5V 2A DC

  12V 3A

  15V 3A

  45W max

  Additional information about the message;

  Message; "For maximum performance, connect a higher capacity Power Adapter.

  In the taskbar, the icon indicates that the message is from HP system information.

  Application properties (found via the Task Manager) HP system information are;

  • File; USBCMSG.exe
  • Location; C:\Program Files (x 86) \HP\HP event system
  • Version of the file; 1.4.14.0
  • Version of the product; 1.4.14.0
  • Date of change; 20/06/2016
  • Original file name; SysInfo.exe

  Good news is that there is a difficulty.

  I was given further guidance to Support cat HP, including a link to the page software and downloads.  This shows a new BIOS Softpaq, which has not been suggested by HP Support Assistant. Details of the update of the BIOS are;

  HP Notebook System BIOS Update (Intel processors) F.26 Rev.A 15.4 MB 24 August 2016

  File name: sp77130.exe
  Communicate details
  Exit the: 12 August 2016
  Version F.26 Rev.A

  I have applied this update of the BIOS and the wrong power adapter warning message no longer appears.

  Problem solved. Thank you HP.

• Satellite Pro L20: battery not charge when the power adapter is connected

  Hello

  all advice appreciated.

  I had a Satellite Pro L20 for about 18 months. Recently, battery does not charge when the power adapter is connected. The battery light starts yellow (which means more liberated, I think?), then will both green, the machine sat for awhile. However the ACPI often said that AC is "offline."

  There are two recent occurrences that coincide with this problem, I try to eliminate:

  1. my friends rat chewed by the feeder for pets! Power is Mobile OK insofar as he fled sector - the rat seems to have simply chewed by the outer cover (I see some threads, but I think that is just a shield, although I'm not an electrician).

  2. I put the laptop in hibernation for the first time. That seemed to mess up the system a bit, which was what initially drew my attention to the problem. This question is a bit complicated because I'm under Linux (Xubuntu).

  I updated the drivers etc from windows when I bought the laptop. Never had any problems until now and have been running linux for centuries. Also, I have mainly the laptop the power supply turned off, but do not remove the battery (is that really a problem these days?)

  I obviously need to replace the adapter, but is - it is likely (and how I can check) that the battery was borked until?

  see you soon
  Chris

  First, please check if the other are lit.
  If the AC led and power led are on the adapter sector is ok and it provides the power to the laptop.

  > The battery light starts yellow (which means more liberated, I think?), then will both green, the machine sat for awhile
  If the battery LED is yellow, this means that the battery is not fully charged and if the Green led changes then recharging is caught and the battery has been recharged.

  So I really don t see any problems with the charge process.

  Maybe the battery is old and so you cannot use it for an extended in such a case only the replacement of the battery could help.

• Computer HP laptop goes black when the power adapter is connected

  Hello, g ' Day

  I have a HP Envy Sleekbook m6 and just today I realized after plugging in the power adapter tge screen woul go completely black. I can hear the cell phone still in market, but I don't see anything. If I play music until the screen goes black, it stops. I tried to change the power plan to see if that would settle the matter, but it does not work. Is there a way I can fix this?

  Thank you in advance.

  Hi jessiecornwall,

  Thank you for the information. I suggest you go to Device Manager and right click on your graphics card and update was from there. Here is a document of Manager of devices for Windows 8 information which has steps for the error codes you get.

  I am also including this document for an Overview of the switchable graphics or Dual GPU that explains what they are and how they work.

  I hope that this information help, please let me know how it goes.

  Thanks and good luck!

• iPhone not charging when connected to the USB power adapter

  Hello. I have a 5 s iPhone that I bought used a few months ago. It works very well.

  Normally I charge it by connecting it to my Mac via a USB cable. Last night, I tried to recharge by connecting Apple USB power (also called a power outlet) adapter, which plugs into the wall, supplied with the phone. (Here's a link to the adapter if you are not sure what I'm talking about:.) When I connect the iPhone to the power adapter, I saw that the phone is charging - there was the small icon representing a lightning bolt near the battery of the iPhone.

  However, when I woke up in the morning, the iPhone has been charged only 47%. I don't remember what the percentage was when I plugged into the power supply last night, but I don't think that the phone at that time was much less.

  So I wonder: nobody knows what went wrong? Is there a way to make sure that the phone is loaded with the adapter?

  Thank you!

  M

  If there is a symbol of bolt of lightning next to the battery icon, then the phone should be in charge.  If it is charging a single source, but not another, then the problem is with the unpaid source.  Try another adapter to confirm.