Trouble with iMac connecting directly to the modem

Similar Questions

• Windows removes the internet conntction system. Connected directly to the modem. Have tried to go through just wifi. the same problem. Only happened for several weeks.

  Windows deletes internet conntction after a few minutes. The netgear and control panel says I'm always connected. Must reboot to get reconnected to the windows system. Connected directly to the modem. Have tried to go through just wifi. The same problem. Only happened for several weeks.

  Hi Sailortdt,

  Welcome to Microsoft Community where you can find the answers related to Windows.

  According to the description, it looks like you are facing a problem with network connectivity.

  It would be awesome if you could answers to these questions in order to help you further.

  1. have you made changes on the computer before this problem?

  2. you receive an error message or error code?

  I suggest you to see the steps in the following Microsoft article and check if it helps.

  Problems in Windows wireless and wired network connection: http://windows.microsoft.com/en-US/windows/help/wired-and-wireless-network-connection-problems-in-windows

  If you need Windows guru, do not hesitate to post your questions and we will be happy to help you.

• E2700 cannot connect directly to the modem, but connects via another wifi router?

  I have a Netgear WNDR3700v2 that I was very pleased until I had a nest of thermostat. Apparently it's a router not supported and I had to change it. I bought an E2700 since he took charge, but I have a huge dilemma...

  If I connect the linksys directly to the modem, I don't get an internet connection. I got out and renewed IPs without success...

  But if I wired the linksys for the netgear, I get a good solid internet connection. problem is, I have no need for installation of 2 routers on top of each other...

  any suggestions? I would like to know what kind of information you need.

  Basically, I do not understand why he is not able to connect directly to the modem to linksys. Yet, it becomes solid connection wired through another router.

  I use Comcast and South FL. it is motorola surfboard modem

  OK, found the solution.

  call 1800COMCAST

  go to the problems of the internet, there is an option to send a refresh signal to your modem.

  I did, and it started working. I guess that clears the memory and binds to the new MAC address...

  After that I did, internet is back. I hope this will be useful to someone. I was ready to return the dang thing.

• Satellite 1900 cannot conect directly to the modem via Ethernet cable

  I have a Satellite 1900 305 and I can't access internet when it connects directly to the modem cable via ethernet (RJ45), even after doing the procedure of recovery, and before I could. I can work normally and have internet if I connect to the pit of the modem a network hub. Can someone help me with this problem?

  Hello
  If I understand you correct you a trying to connect your laptop via Ethernet to a router or Modem or anything else, which is connected to the internet.

  Well it be, that the cable you a way to make this either a cable crossing of files?

  Good bye

• When I connect my computer to the Netgear router, they do not seem to recognize the signal from the modem. I have to run each device directly to the modem (one at a time) for internet access.

  I have both a laptop and a desktop computer and use a modem wired high-speed internet.  I bought a router "Netgear" 5 port so that I could have both online at the same time, but when I connect my computer to the router, they do not seem to recognize the signal from the modem. I have to run each device directly to the modem (one at a time) for internet access. It gets very tedious, please help...

  Original title: router does not work...

  Hello

  Welcome to the Microsoft community.

  I see that when you connect multiple computers using the Netgear router, it does not recognize the signal from the modem.

  You must contact the ISP to verify if they can help you with this question.

  In addition you can keep these items handy, it might help you.

  Set up a wireless router

  http://Windows.Microsoft.com/en-in/Windows7/set-up-a-wireless-router

  Install or remove a modem

  http://Windows.Microsoft.com/en-in/Windows7/install-or-remove-a-modem

  Change modem settings

  http://Windows.Microsoft.com/en-in/Windows7/change-modem-settings

  It will be useful.

  If you need help with Windows, let know us and we will be happy to help you.

• ISA550 Wan speeds VS direct to the modem

  Today, I noticed that if I connect my computer directly to the modem, I get speeds of 67MBPS down and 3.5 upward. When I go through the ISA550 I get 47 down and 3.5 upward. Is - fixable?

  Hello

  Your speeds are most likely more slow because of running security services your CEP.

  I took a quick look at the Datasheet for the ISA550 and the flow when the different threat management features are enabled is listed to 45Mbps, right around what you have found.

  As a test of cross and disable the security services one at a time to refine that slows you down, my guess would be the A / V or IPS.

  Is repairable way, using just the firewall, the device can handle up to 200Mbps, but that means you would need to disable certain functions for security.

  Hope that helps and thanks for using Cisco,

  Christopher Ebert - Advanced Network Support Engineer

  Cisco Small Business Support Center

  * Please note the useful messages *.

• How to connect directly to the DB

  It is possible to create a form to so as to not ask for user/pass/database each time that you use, but by connecting directly to the DB? I mean, it is possible to write something in the form that I know not to put directly within the user/pass/basic form of data instead of ask for it every time?
  Thank you!

  Hello

  for this, we must change formsweb.cfg
  Just add the following to the configuration section.

  [Your_config]
  userid=user/pwd@connect
  

  Sarah

• SpeedTest E3000 50 percent SLOWER when I connect the PC directly to the Modem cable

  Hello

  My ISP is Comcast and I've recently updated my service to have up to 50 MB speeds yo and upward at 10 MB.

  My router is the E3000.

  When I connect my PC directly to a cable modem and perform a speed test (www.speedtest.net), I get 61 MB download and about 11 download fairly regularly.

  Now when I use the router configuration to connect my PC to the E3000 and then run the speed test, I get 50% LESS!  So, my download is on average around 30-31 MB and my upload is 4 to 5 MB.

  In fact, I thought it was the E3000 and went out and bought a Netgear and got the same results.

  In both cases, I have updated the firmware to the latest version and I also updated my PC to the latest drivers adapater.

  I even tried to manually set the MTU to 1500.  Nothing works!  It is still 50% less achievement when I connect through a router.

  I expect a bit of slowdown during the connection through the router, but certainly not 50%.  And, Yes, 50% is consistent.

  Any ideas on what could cause this 50% slower?

  Thank you!

  Well, I agree on that. Speedtest.NET is not accurate. I don't even use it to measure my speed of internet connection.

  If your connection is 50Mbps, then you should get 6.2MBps more or less of download speed. It is normal that you get at least 80% of your download speed.

  I think that there is no problem at all with your connection.

• Controller of domain and DNS behind RRAS without VPN connected directly to the internet with a Cisco router

  I hava a ME Cisco 3400 with physical single port available for a cable connection.

  The ISP give me an IP address interface = 89.120.29.89 to act as a gateway to the IP Address of the host, which is provided for in the order 89.120.29.90.

  The host computer is a dual Xeon computer with two NICs for LAN and WAN.

  Fields of application: to install a windows 2008 R2 between public and private network server.

  Even though I know it's not recomanded, I put the DNS role and directories Active Directory roles installed on the same computer, the computer above, (I do not have enough computer for roles different place on different computers)

  The desired configuration:

  To have installed with his roles behind a WS2008R2 has RRAS. without a VPN.

  b with VPN

  and for WAN access for the client computers of the private LAN Windows 7 OS. (The basin of LAN address 192.168.0.1 - 255).

  First step : to have internet access in the browser (I use Google chrome) (without taking into account the DNS and AD)

  Network configuration:

  Map NETWORK WAN, at the top of the stack of liaison in the Control Panel/network connections and sharing:

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  OK, I can browse the internet.

  Second stage. (Consider DNS and Active Directories)

  DNS instaled role for this computer.

  AD installed as a global catalog.

  NETWORK WAN server that is directly connected to the Cisco router:

  Conection area 3

  Properties:

  Client for Microsoft Netwaork: not verified

  Network Load Balancing: not verified

  File and shared printer: not verified

  QoSPacketScheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 89.120.29.90

  Mask: 255.255.255.252

  Gateway: 89.120.29.89

  DNS: 193.231.100.130 my ISP name server address.

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: not verified

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: not verified;

  Use this connection DNS suffix in DNS registration: not verified;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: don't check;

  Disable NetBios on TCP IP: checked;

  Connection to the local network 2

  Properties :

  Client for Microsoft Netwaork: checked

  Network Load Balancing: no

  File and shared printer: checked

  QoS Packet Scheduler: not verified;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4 checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  NETWORK LAN CARD: 192.168.0.101

  Mask: 255.255.255.0

  Gateway: 192.168.0.1

  under Advanced tab:

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: check;

  Disable NetBios on TCP IP: not verified;

  Install RRAS as NAT (NAT) under any condition imposed by DHCP(not installed) in ideea that RRAS will generate the private IP address of the DHCP allocator.

  In any case, for the beginning, I have a fix IP, do not get IP automatically.

  At this point, it gets the configuration simple posible for RRAS follows:

  3, LAN connection that corespond to the WAN interface IP:

  "NAT configured for the following Internet interface: Local Area Connection 3.
  The clients on the local network will assign the IP addresses of the following range:

  network address: 192.168.0.0. netmask 255.255.0.0.

  After Windows RRAS are open:

  The Network Interfaces tab:

  NICs are enabled and connected;

  UAL remotely & policies:

  Launch NPS,

  on the NPS server tab:

  Allow access to successful Active Directory directories:

  Properties: authentication: port 1812,1645

  kept port 1813,1646;

  on the accounting tab: nothing;

  under NPS policies:

  Grant permission for the RRAS server under builin\Administrator of the accounts;

  On strategy and the type of server unspecified (NAT do not exist as an entry in the drop-down list server dwn)

  under the static road: nothing;

  under the IPv4 tab or both are there(there IP) and are up

  under NAT

  Connection to the local network 3: public interface connected to the internet

  enable NAT on this interface:

  under the address pool: ISP addresses public;(two addresses)

  under the terms of service and the ports: Web server: http 80.

  (I have I have a static IP address for the client computer in mind, I set up a single customer).

  At the client computer :

  configured as domain customer and added to the users AD and computer AD

  logon to the domain:

  Local Area Connection

  Properties:

  Client for Microsoft Netwaork: checked

  Network Load Balancing: not verified

  File sharing and printer: checked

  QoS Packet Scheduler: checked;

  Microsoft Network Monitor 3 pilot: not verified

  IPv4                                                     ;  checked

  Pilot a Link Layer Topology Mapper i/o: checked

  Link layer Discover responder: checked

  IPv4 tab

  Host IP: 192.168.0.101

  Mask: 255.255.0.0

  Gateway: 192.168.0.1

  DNS: (auto-add the same to the local machine).

  under the tab advanced

  IP settings : even that, tab IPV4 with automatic metric check;

  DNS tab :

  Add primary and connection suffixes DNS specific: checked

  Add suffixes primary DNS suffixes parents: not verified

  Add this DNS suffixes: no

  Registry deals with this connection in DNS: checked;

  Use this connection DNS suffix in DNS registration: checked;

  WINS tab : enable search LMHOST: not verified

  Enable NetBios over TCP IP: checked;

  Disable NetBios on TCP IP: not verified;

  right now the 192.168.0.101 client cannot connect to internet through RRAS.

  ;

  This issue is beyond the scope of this site and must be placed on Technet or MSDN

  http://social.technet.Microsoft.com/forums/en-us/home

  http://social.msdn.Microsoft.com/forums/en-us/home

• My Y510 is unable to connect with WiFi need to reset the modem, and sometimes both

  Hello

  My Y510 sometimes does not connect if my Wi - Fi if one of them started earlier then the other, I went to the media and automatic downloads to make the drivers and software upgrades through its tells me that all devices need update is no update. To connect to wireless internet, I restart my modem, and sometimes both.

  You guys you suggest... Thank you

  Check the site of the manufacturer of the modem for the firmware update if available.

  start-up your computer, press f8 to load in SafeMode (networking) and try again, lets see the problem persists.

  If the problem persists, uninstall the network drivers, restart your computer and install it again.

• XI of hp photosmart 2710 can I connect directly to the computer? running Windows 7

  I have a computer with Windows 7, also have another all-in-one printer

  but want to know I am able to connect Hp Photosmart 2710xi directly to the computer?

  Hi funtimepatty,

  Yes, follow the steps outlined in the document below.

  http://support.HP.com/us-en/document/c01796736

• connection for printing from a computer wireless with a connection cable to the router usb printer?

  Produst name: HP Officejet Pro L7555.

  Works with Windows 7.

  A new router and the modem was installed when Comcast installed our wireless connection.  This of course did not work with the current setting of the printer.  The printer is connected via USB cable to the router.

  Are you sure it's a USB and not an Ethernet cable?  I bet it's in the affirmative:

  1. disconnect the Ethernet cable.

  2. on the printer: Setup > network > default settings.

  3 reconnect the Ethernet.

  Now, remove the printer in Control Panel > devices & printers, then add it again like this:

  1. make sure the printer is on and connected to your network. Verify that you can access the printer's internal web page by accessing its IP address before continuing. Get his IP address for a network Test printed on the front of the printer.
  2. click on > start > Control Panel > devices & Printers.
  3. click on add a printer
  4. Select local printer
  5. Select create a new port and select Standard TCP/IP Port, and click Next.
  6. under device type, select TCP/IP Device. Under the name of host or IP address, enter the IP address of the printer. Click Next.
  7. Select Hewlett-Packard in the list of manufacturers and select and select your printer model. Click Next.
  If your printer model is not in the list, then select disk provided, browse the CD that came with your HP printer and select the first file begins with hp and ending with INF. click Open, then OK. Select your printer model. Click Next.
  8. If prompted, use the driver that is currently installed.
  9. He will ask the name of the printer - enter a new name or use the one existing. This will be the name of the printer that you select from other applications.
  10. we may ask you to share the printer. Choose No.
  11. the printing area of Test Page is displayed. Go ahead and print it out.
  12. click on finish.

• Question about creating report guests editor BI when it connects directly to the database?

  Hello

  I create a report of BI Publisher using direct SQL server database. JDBC connection is created, then datamodel and report.

  The report is parameterized. Now I have attached the dashboard report. But now the settings are not filling. So I intend to create guests, but it is the search for field. But I don't use of RPD. So, how can I create guests when we creating BI publisher report connecting directly with the database? Please let me know.

  Kind regards
  Sam

  Hi Sam,

  I hope you got your answer for that starting from the thread OBIEE quick dashboard for BI Publisher

  Thank you...

• PCoIP connections directly on the desktop or via the connection to the server?

  Hello

  I have install a single view connection server and office pool and I can connect to the pool very much using the customer view pointing to the login server.

  I recently added a second login server replica and if I try to connect via the customer view succesfully authenticates, allows me to choose a pool, but errors and then with "the connection to the remote computer has ended."

  Look at newspapers in firewall, can I see traffic blocked from my desktop PC (where the client to view runs) to the IP address of the VM on the port office 4172. Of course, I can open this port, but I do not understand why this should be necessary when using the first server likely traffic goes through the connection to the server, not directly to the customer. The behavior looks different during the passage through the replica, but I don't see why this would be the case?

  You can enable/disable tunneling with a broker for connections setting.  Maybe the second broker (replica) does not make any tunnel and trying instead to go directly through your PC.

• New CP - 910 can not connect directly to the Windows 7 computer.

  I try to get my Selphy CP-910, set up and not having luck.

  I try to print using my laptop the printer two ways; direct connect and Wi - Fi via the access point.

  I do the initial installation and when I launch the CD with drivers and follow the directions, I get to the point where the printer is detected and it never gets detected.

  It happens as well with the live mode and mode access point.

  Can anyone help?

  This has been resolved.

  I had to disable my windows firewall and windows defender antivirus.