TSST corp CDDCDW SN - 208AB Code 19 after loading win Pro 8

Similar Questions

• Satellite Pro A200 - Wifi does not not after loading Win XP

  Hi, I'm new here and I apologies if this has been covered, I searched the Forum but came up to the top with nothing.

  I have a:
  Satellite pro a200
  Windows XP.

  My laptop was xp professional installed and the wifi on Board did not work.
  I had problems with the global laptop but the wifi worked. I formatted last night, installed a new copy of xp home and now wifi doesn't seem to be recognized. The light is on, the switch, but I can't get the laptop to recognize her here.

  I did not much I know, but I hope I can get it sorted.

  You have any questions, I will try and respond with as much information as possible.

  Thank you, my.

  Hello

  Please not that after the installation of Win XP, the BIOS needs to be updated!
  The Toshiba page should provide a special BIOS for Win XP OS update.

  A note of juice; the laptop could be equipped with different WLan modules and so you should be aware of chip right WiFi WLan card would not work if you try to install incompatible driver!

• Motorola surfboard SB5101 modem does not connect after loading Win 7 OS

  I had Win XP 32 bit and have now updated for Win 7 64 bit (I have a 64-bit processor) now my computer does not connect to my modem - Motorola Surfboard SB5101 even if styling check here says it should be OK.  When I try to connect I get this error: failed to connect #651, modem or other reporting device connection error.

  My service provider could not help and said my signal to connect is good.  I loaded the new drivers Vista 64 for my modem as it was the only rider to a 64 bit OS that I could find, in the hope that it would help.  No chance here no more.  Any suggestions?

  I guess that you connect the modem to your computer with a USB cable.  If your modem has an Ethernet output, use it instead.  The Ethernet connection does not require a pilot program and is more reliable than the USB connection.

• Driver TSST Corp CDDVDW TS - L633L ATA Device will not load. The problem code is 19 / how to fix?

  HP Pavilion dv4
  TSST Corp CDDVDW TS-L633L ATA Device

  Control Panel / problem report and solutions
  Problem: Could not load software driver status: sent report

  Description
  Windows was able to successfully install device driver software, but the driver has encountered a problem when he tried to run. The problem code is 19.

  Signature of the problem
  Problem event name: PnPDeviceProblemCode
  Architecture: x 64
  Hardware ID: IDE\CdRomTSSTcorp_CDDVDW_TS-L633L___0400___
  Configure the class GUID: {4d36e965-e325-11ce-bfc1-08002be10318}
  The PnP problem code: 00000013
  Driver name: cdrom.sys
  Driver version: 6.0.6002.18005
  Driver date: 11/04/2009
  The system version: 6.0.6002.2.2.0.768.3
  Locale ID: 1033

  Additional information about the problem
  Bucket ID: 619663520

  Control Panel / Device Manager
  Windows cannot start this hardware device because its information of configuration (in the registry) is incomplete or damaged. (Code 19)
  Click on 'Search for solutions' to send data about this device to Microsoft and to see if there is a solution available.

  I tried:
  Update driver software
  Uninstall / find the hardware changes
  Uninstall / reboot / new hardware found
  Properties / verification solutions

  How can I fix it?

  Hello

  Try to follow the procedure at the title of the subheading "Let fix me it myself" on the link below to delete the upper and lower filters and see if that helps the issue.

  http://support.Microsoft.com/kb/982116

  You have to restart the laptop after that.

  Kind regards

  DP - K

• code error 19 for TSST corp DVD + _RWSN-208BB on a Dell computer

  I get an error code of 19 for TSST corp DVD + _RWSN-208BB, it's a Dell computer that was a floor model

  What should I do to play my DVD?

  Hi Bruce,.

  Try to remove the GEARAspiWDM entry.

  To remove the GEARAspiWDM entry double-click UpperFilters and, under value data, delete GEARAspiWDM > OK

  Create a system restore point beforehand and restart the computer after.

  However, if you have an application that uses the GEARAspiWDM, like iTunes, just install the latest version of hardware drivers (4.021.1) and that no changes to the registry:

  http://www.GearSoftware.com/support/drivers.php

  Updated speed drivers should also correct the mistake.

• PILOT DELIMMA! I have a TSST corp CCA/DVD TS-L462D ATA device driver & get code 19

  Original title: DRIVER DELIMMA! I have a TSST corp CCA/DVD TS-L462D ATA device driver & receive code 19, I tried all HELP!

  Please see above, how can I fix code 19?      Thank you!

  Hello

  I suggest you run the fixit from this link and if it helps:

  http://support.Microsoft.com/kb/314060

  Check if that helps.

• Reinstall for TSST corp CDDVDW TS - L633B ATA device

  I have the yellow exclamation mark beside TSST corp CDDVDW TS-L633B ATA cd/dvd drive device, I ran a fix, but it tells me that I need to reinstall. How can I do this? The cd player has always been very sensitive. Sometimes, longer works once not.

  I have the yellow exclamation mark beside TSST corp CDDVDW TS-L633B ATA cd/dvd drive device, I ran a fix, but it tells me that I need to reinstall. How can I do this? The cd player has always been very sensitive. Sometimes, longer works once not.

  Here is the solution to update your device with the latest driver of Toshiba/Samsung.

  Introductory material.

  
  

  1 here is the update for TSSTcorp CDDVDW TS-L633B ATA DEVICE.

  2. There is a update for the Samsung TS-L633B, but there only version SC01, which WILL NOT be updated the version of the TS-L633B HP because HP version is 0301 with an OEM Code of HM.

  3. However, Samsung has renamed TS-L633B with a new device driver ATA which is called SN-S083B and has a pilot SC02 update.

  4. the way that you update TS-L633B Code 0301 Version with HM Code OEM with the new Samsung SN - S083B Version SC02 Code is to patch the file and flash TS-L633B HP with the patched file.

  Instructions.

  
  

  IMPORTANT - THIS ONLY REFERS to those who have the HP TSSTcorp CDDVDW TS - L633B ATA Device - check device manager to make sure that you have this model number device driver before you start - YOU DO THIS at YOUR OWN RISK. Proceed only if your product is not guaranteed and do not wish to pay for another DVD player.

  1. click on the following link and download the firmware SB02. Global Distribution of SN-S083B: http://www.firmwarehq.com/download_1380-file_SN-S083B_SB02.exe.html

  2. If you don't have a utility program unzipped, click on the following link and download and install 7zip that corresponds to your computer from the following link: http://www.7-zip.org/download.html

  The BIN SN-S083B unzip using 7zip by right clicking on it and choosing 7ZIP > extract here.

  3 download the Flash Samsung Standalone utility:

  http://www.samsungodd.com/KorLib/file/tsdnwin.exe

  4. download and unzip http://ala42.cdfreaks.com/MCSE/MediaCodeSpeedEdit.zip to ala42 MCSE

  Download source: http://ala42.cdfreaks.com/MCSE/

  5 create a folder and name it FLASH and place the following 3 items in the folder.

  SN - S083B_SB02.bin that you have checked out

  Flashing Samsung Standalone utility

  MCSE of Ala42 you have downloaded and extracted the zip file

  6. After you have placed all three objects in step 5 in the folder named FLASH, place the FLASH folder and all of its contents in the C drive.

  7. After placing the FLASH folder in C drive, open the folder and CLICK on RUN AS ADMINISTRATOR and ALA42 MediaCodeSpeedEdit.exe RIGHT.

  8. when ALA42 MediaCodeSpeedEdit.exe opens, click the LOAD button and place you in the FLASH folder in C drive and load the file SN - S083B_SB02.bin - when the file it load it will show all of its regions.

  9. once the file SN - S083B_SB02.bin is fully loaded, place a check MARK in the area of CPR1 in the lower right of ALA42 MCSE.

  10. After putting a check in the box by ALA42 MCSE CPR1, click SAVE in the upper right and save the file in the file FLASH as SN - S083B_SB02_speedpatched.bin.

  11. now go to START > all PROGRAMS > ACCESSORIES > COMMAND PROMPT and right click on command prompt and choose RUN AS ADMINISTRATOR to open the command prompt in the Administrator role.

  12. once the command prompt opens, type the following command: CD C:\FLASH and press the ENTER KEY.

  13 after hitting the button enter, the command prompt should read FLASH.

  14. to the FLASH command prompt, type the following: nocheck tsdnwin and press the Enter button to open the flashing Samsung Stand Alone.

  15. when the flashing Samsung Stand Alone opens, click on the on button SEARCH and navigate to the file 'SN - S083B_SB02_speedpatched.bin"to load it into Samsung's Flash utility.

  16. the file "SN - S083B_SB02_speedpatched.bin ' will load and click on DOWNLOAD to start flashing your TS-L633B ATA Device.

  Wait until the flash is finished and when it finishes, it will ask you to restart the computer and you must restart.

  When you rebott and are back at your desk, Windows will recognize the drivers for your TS-L633B ATA Device and install the new drivers SN-S083B_SB02.

  When it finishes installing your drivers, restart the computer once more, and then you're done.

  NOW ENJOY your CD/DVD-RW drive updated.

• TSST corp DVD won't read or write

  I have a desktop Dell VISTA computer.  He's got a TSST corp DVD +-RW ts-H653B ATA Device.   When I got the computer from Dell (April 2008), the DVD worked fine.   Now it is not recognized by Device Manager - it is for me a "Code 10" - that it does not start.   I tried everything.  My machine is a Dell VISTA home Premeium

  Any ideas? send me an email to * address email is removed from the privacy *

  Hello

  Description of errors related to the 10 Code that generates the Device Manager in Windows on computers
  http://support.Microsoft.com/kb/943104/

  Please make all below even if you have done some before as it is often the set of operations which solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click on the device - driver tab - click
  Update the drivers (this will probably do nothing) - then RIGHT click the drive - UNINSTALL - REBOOT
  This will refresh the default driver stack.

  Then, work your way through these - don't forget the drive might be bad, could be a loose cable or
  slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the installation of Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  Hope these helps.
  Rob - bicycle - Mark Twain said it is good.

• Problems with TSST corp CDDVDW TS-H653Z

  MY TSST corp CDDVDW TS-H653Z does not recognize CDs and recordable DVDs. According to Windows, the latest version of the driver is installed. Any suggestion? Thank you.

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting could not help if there is alignment and/or wear issues however it
  a shot.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double click on the device - driver tab.
  Click on update drivers (this will probably do nothing) - RIGHT click ON the drive - uninstall.
  RESTART this will refresh the default driver stack. Even if the reader does not appear to continue
  below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other programs-
  a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you upgraded to
  for Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error in Windows
  Vista installation after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then make sure that the cables in both
  ends. Remove and replace, do not just tight. For laptops, you can often clean power and
  contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the manufacturer of system and
  manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD
  Burn and CD and DVD read). So it is not unusual for 1 or 2 operational so that other parts
  do it right.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  the entries in registry that the troubleshooter does not solve and those who "might" be the cause.

  Check with your Maker system and a device for the two possible firmware updates and
  the correct registry entries for your car.

  Here are the keys that I of course are those in question - for the subkeys of the CD/DVD drive
  as there will be other subkeys in these keys. Do not forget to ask specific keys involved as well as
  the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even the exact registry for your CD/DVD settings
  drive from someone with the same model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager, which displays all the
  devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• TSST corp CDDVDW TS-L633B stopped reading and writing

  I have a laptop Acer 4736Z with a TSST corp CDDVDW TS-L633B DVD - RW, so decide simply ceased to read and write DVDs and CDs. When I insert a blank dvd, it will ask me to burn files to it but when I do, it complements the habit and will the useless DVDs. When I insert CD or DVD, the drive does not read it more.

  Please help me on how to solve this problem.
  Thank you

  Hello

  You have disk problems as the CD/DVD is actually 4 discs in 1 case (CD & DVD burning and)
  Playback of CD and DVD). So it is not unusual for parts from 1 or 2 to not work so that others do
  correctly.

  Burning at low speed, or by using the master could help. A CD/DVD cleaner might help.

  Brand of the CD or DVD drive can also be the problem. Low quality (cheap brands) are always problematic.

  CD/DVDs have a tolerance + - and your can read/write on the edge outside these discs
  tolerances. They may be delivered, but it is generally more economical to replace the disk.

  Several good info here:
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Notes on the troubleshooting and repair of readers of compact disks and CD-ROM Drives
  http://www.repairfaq.org/repair/F_cdfaq7.html#CDFAQ_014

  ===========================================

  This troubleshooting might not help if there are problems of alignment and wear it
  is worth it.

  Step 1: Please do all the same underneath if you did some before as is often total
  a process that solves the problem.

  Try this - Panel - Device Manager - CD/DVD - double-click the device - driver
  Tab: click on update drivers (this will probably do nothing) - then do a CLICK RIGHT to the road.
  UNINSTALL - REBOOT this will refresh the default driver stack. Even if the disc is not
  shown continue below.
  
  Then, work your way through these - don't forget the drive might be bad, could be a coward
  cable or slight corrosion on the contacts (usually for a laptop) and other issues.

  Your CD or DVD drive is missing or is not recognized by Windows or other programs
  http://support.microsoft.com/kb/314060 - a Mr Fixit

  Try this fix manually if the Fixit 314060 does not work
  http://www.pchell.com/hardware/cd_drive_error_code_39.shtml

  Your CD or DVD drive is missing or is not recognized by Windows or other
  programs - a Mr Fixit
  http://support.Microsoft.com/kb/982116

  The CD drive or the DVD drive does not work as expected on a computer that you
  upgrade to Windows Vista
  http://support.Microsoft.com/kb/929461

  When you insert a CD or a DVD, Windows Vista may not recognize the disc
  http://support.Microsoft.com/kb/939052

  Your CD or DVD drive cannot read or write media - A Mr Fixit
  http://support.Microsoft.com/GP/cd_dvd_drive_problems

  CD/DVD drive does not appear in Windows Vista, or you receive this error during the
  Setup Windows Vista after booting from the DVD (AHCI)
  http://support.Microsoft.com/kb/952951
  Drive CD - R or CD - RW Drive is not recognized as a recordable device
  http://support.Microsoft.com/kb/316529/

  Hardware devices not detected or not working - A Mr Fixit
  http://support.Microsoft.com/GP/hardware_device_problems

  Another possibility is that the cables are loose. Remove ALL power, then check
  in both ends of the cables. Remove and replace, do not just tight. For portable computers, you can
  Often, clean power and contacts data with a pencil eraser.

  Some DVD players do not use the Windows default drivers so check with the system
  Designer and manufacturer of device to see if there is a firmware or drivers for your drive if necessary.

  ===============================

  Step 2: You have disc problems as the CD/DVD is actually 4 discs in 1 case
  (Read burn CD & DVD and CD and DVD). It's not unusual for 1 or 2 parts to not
  function, while others do so correctly.

  Did you follow the Troubleshooting Guide for the reader who still does not work? There are
  some registry entries that do not fix the resolution of problems and those who 'could' be the
  cause.

  Check with your system manufacturer Maker and device for these two possible firmware updates
  and the correct registry entries for your car.

  Here are the keys in my opinion, are those in question - for the subkeys of the CD/DVD drive
  of course there will be other subkeys in these keys. Do not forget to ask specific keys
  in question as well as the parameters.

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Hardware Profiles\0001\System\CurrentControlSet\Enum\IDE

  HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Class\ {4D36E965-E325-11CE-BFC1-08002BE10318}

  -----------------------------------------------------------------------

  You can probably find more info here and maybe even right for registry settings
  your CD/DVD from someone with the same drive model.

  Forums - a lot of expert real help
  http://Club.myce.com/

  CD/DVD units
  http://www.myce.com/storage/

  Use DevManView to locate the CD/DVD in the registry (be careful and do a prior Restore Point)
  nothing change) - find the DevManView device and then make a right click on it free in RegEdit.

  DevManView - free - an alternative to the standard Windows Device Manager,
  that displays all devices and their properties in flat table, instead of the tree viewer
  http://www.NirSoft.NET/utils/device_manager_view.html

  I hope this helps.

• Equium A210: "tsst corp ts-l632h" firmware is not compatible with my drive

  Last year I had an Equium A210 17l of pc world. I recently bought some dvd - r tdk discs and the drive cannot read them. It's as if there is no disk in the drive.
  So I thought I'd hunt around to see if there is updated firmware for the drive. I downloaded the firmware from this site, but when I try to update it says that the disc is not compatible! Evey bit of software I said the player is a * tsst corp cddvdw ts-l632h * with firmware to01.

  The firmware I'm trying to download is [this | http://uk.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?service=UK&selCategory = 2 & selFamily = 382 & selSeries = 173 & selProduct = 742 & STAS hortMod = 680 & language = 13 & selOS = 26 & selType = 50 & yearup load = & monthupload = & dayupload = & useDate = null & mode = al lMachines & search = & action = search & macId = & country = 8 & electedLanguage s = 13 & type = 50 & page = 1 & ID = 63137 & DISO =-1 & driverLanguage = 42]

  But whenever I try to run it it says that it is not compatible with my drive! What is going on?

  Jim Venner

  I recommend you to first install the 2 firmware until the you´re trying to upgrade the drive with the a3 because it is possible that the a3 requires the 2.

  Please visit the site to download drivers, download the firmware 2 and check if it works.
  Would appreciate any comments on your part.

  Welcome them

• I get system off with the code 68072590 after 3 failed attempts

  I get system off with the code 68072590 after 3 failed attempts

  AM trying.

  77950516

  Use this code to go into the BIOS.

  Disable all passwords that are enabled.

  IF demand for CURRENT password using this code.

  REQUEST NEW password just press ENTER.

  If asked to hit just to CHECK password to enter.

  Save and exit.

  REO

  I must inform you that these services are not endorsed by HP, and that HP is not responsible for any damages that may occur to your system using these services. Please be aware that you do so at your own risk.

• I have an acer with SP3 and Windows XP machine. It does not recognize a DVD - RW in my TSST Corp. CD/DVGW TS - L632D

  Original title: DVD problems

  I have an acer with SP3 and Windows XP machine. It does not recognize a DVD - RW in my TSST Corp. CD/DVGW TS - L632D what is the solution. I tried the fix and I also used the Center 'Fix it '.

  Hello

  1 how long have you been faced with this problem?
  2. don't you make changes on the computer before this problem?
  3 are. what patch you referring?
  4. this happens to you with some specific discs?

  Reinstall the drivers for DVD player and check.

  1. click on start > run
  2 type devmgmt.msc and press ENTER. If you are prompted for an administrator password or a confirmation, type the password, or click on allow.
  3. in Device Manager, expand CD-ROM/DVD-ROM drives, right click on the device CD and DVD and then click on uninstall.
  4. When you are prompted to confirm that you want to remove the device, click OK.
  5 restart the computer.
  6. when the computer restarts, the drivers will be installed automatically.

• can't install updates-error code 0000643 after some trys 3 or more

  can't install updates-error code 0000643 after some trys 3 or more on windows vista?

  can't install updates-error code 0000643 after some trys 3 or more on windows vista?

  See if this Microsoft tutorial can help you:

  http://support.Microsoft.com/kb/976982

  Method 1 has an automatic application of FixIt.
  Method 2 has a repair statement.

  Also, take a look at this one from Windows:
  http://Windows.Microsoft.com/en-us/Windows7/Windows-Update-error-80070643

• CDDVD TSST CORP TS-L633M ATA DEVICE DRIVER DOES NOT

  OK so I went on the website of windows (http://support.microsoft.com/gp/cd_dvd_drive_problems) and downloaded and ran the program that makes it surprisingly found the problem and tried to fix it but in doing so, I got a message from PILOT of FACILITIES of SOFTWARE developed in the taskbar that says that it not to repair the failing TSST CORP CDDVD TS - L633M ATA DEVICE driver. So now that it is said "Please consult the manufacturer of your device for help to get this installed device." who should I contact?

  -J' have a HP PAVILION DV6 121 6SA

  Hi Woody94,

  TSST CORP stands for Toshiba Samsung Storage Technology Corporation. This pagehttp://www.tsst.co.kr/korea/en/techinfo/svccenter.php gives a map of service centers around the world. You will probably find an email from support by placing the center of service to you.

  If not, have you contacted HP support to see if they can help? http://WWW8.HP.com/UK/en/contact-HP/contact.html This link is to HP support to the United Kingdom. If you are in another country, just visithttp://www.hp.com and check the support pages or contact pages. You can also consult the user's guide for your PC to see if support details are included here.

  This forum post is my own opinion and does not necessarily reflect the opinion or the opinion of Microsoft, its employees or other MVPS.

  John Barnett MVP: Windows XP Expert associated with: Windows Desktop Experience: Web:http://www.winuser.co.uk;  Web: http://xphelpandsupport.mvps.org;  Web: http://vistasupport.mvps.org;  Web: http://www.silversurfer-guide.com