Tunnels of router that support s multiple VPN IPsec AND SSL VPN

Similar Questions

• "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".

  Original title: when setting up Windows Media Center, I get the error message: "IR hardware not detected".

  I have an internal TV Tuner that has been installed by HP, when I bought recently a "computer build-your-own." (According to the control panel Device Manager, my tuner is a Win TV HVR 1290, made by Hauppauge). The computer came with Windows 7. While installing Windows Media Center, after setting up the TV Signal (on channel 3) I am able to see a video thumbnail on my computer screen. I am also able to change the channel using my remote control U-Verse (not the Windows remote control supplied with the computer). So far so good! I then hit next and get the following message: "Windows Media Center cannot detect the IR control cables, which are necessary to control the set-top box. Fixing parts IR that supports the IR control cables and then try again. IR HARDWARE NOT FOUND ".  After you receive this message, the installation procedure is completed. I called HP that support intalled the tuner. They had not the slightest idea what to do. I then called Hauppage customer (manufacturer of TV Tuner). They said that I need to plug one end of the IR Blaster cable that shipped with the computer in a slot in the back of my computer (they told me which slot). They said so to run the IR all the way cable to my cable box and the other end of the cable to my cable box of band. They said it was necessary to be able to use my Microsoft Remote to instruct the box to change channels (cable IR stuck on the box). I told her that I did not use the Microsoft Remote, I could change the channel with my U-verse remote (that I preferred to use anyway). He said that it took the cable on the band decoder in order to remove the error message and the installation of Windows Media Center. I then called U-Verse technical adapter who informed me of their set-top boxes (made by Cisco Systems) do not have the ability to receive signals IR IR Blaster cable (or any othe IR signal source). Microsoft is apparently not understand how U-Verse set-top boxes are designed to work and sells a product incompatible remote control/IR. My question is this: How do I set up Windows Media Center, in order to avoid getting the error message "IR hardware not detected" when you install Windows Media Center and just use the remote control of the U-Verse that I prefer to use in the first place. Once understand you this point, please send the information to HP, At & T U-Verse and others. Thank you.

  Ron, I have something for you!

  and for all the people who have this problem :)

  Hi, I had the time of IR not detected in Windows 7 Ultimate with a TV wonder 650 card and a box of digital adapter from Verizon for my PC... Go on the road to installation and after the Media Center channel search, choose manual configuration. Choose the aerial signal (I aso picked after this analog) l. After he sought more, he finds no channels.  Do not be afraid. Just accept it and go to the main settings page in the Mediacenter. If I remember correctly, then select TV Guide. Choose Add channel. I added the channel 3.

  Since my Verizon box has no IR for the computer, I added the channel 3 for the media Center and I change the channels with my Verizon remote. All my stations in the Verizon box go to Channel 3.

  The story here is so, for some reason any Windows detects that only my box channel signal TV and you must manually configure the media center on the air, then go to settings and add the channel you want in the guide.

  Why the guide TV control which channel you can tune is beyond me, but the scanner locks all channels, it does not detect. they must be added manually in the guide.

  My TV works and looks okay now.

  It actually works!

  the only problem is that it is not in HD

  but there is something

  
  

• Windows IPSEC and SSL VPN client on the same machine

  Matches (coexistence) installation of IPSEC and SSL vpn clients that are supported on the same computer, windows (XP and Win7)?

  As mentioned by Patricia and Jennifer (5 stars), you can install two clients on the same machine without any problem.

  The tricky part comes when you are trying to connect two clients at the same time, that's when you may encounter unexpected problems.

  However, if your intention is to install both clients and connect them individually and not at the same time, you'll be fine.

  If you have any other questions, please mark this question as answered and note all messages that you have found useful.

  Thank you.

  Portu.

  Post edited by: Javier Portuguez

• ASA5505: Configure the ASA for IPSec and SSL VPN?

  Hello-

  I currently have my 5505 for SSL AnyConnect VPN connections Setup.  Is it possible to set up also the 5505 for IPSec VPN connections?

  So, basically my ASA will be able to perform SSL and IPSec VPN tunnels, at the same time.

  Thank you!

  Kim,

  Yes, you can configure your ASA to support the AnyConnect VPN IPSec connections and at the same time.  In short, for the configuration of IPSec, you should configure at least a strategy ISAKMP, a set of IPSEC, encryption, tunnel group card processing and associated group policy.

  Matt

• Camera Raw that supports the two Nikon D800 AND D750?

  Hello! I have a Nikon D800 and I recently borrowed a D750 to test it. The problem is that I can't open the files of the D750

  because my Camera Raw does not support D750. But there is also no Camera Raw updated to support BOTH cameras at the same time.

  All solutions? I would really appreciate it! Thank you

  You need Camera raw 8.7 or higher for the D750. Which will also open files between the D800. You would need PS CS6 or higher for this, so if you do not have CS6, you have to use the free dng converter.

  Adobe - Adobe Camera Raw and DNG Converter: for Windows

  Adobe - Adobe Camera Raw and DNG Converter: for Macintosh

• JWNR2010v5 (N300 wireless router) will support 100 Mbps connection speed internet in LAN?

  I intend to upgrate my internet connection speed of 60Mbps to 100 Mbps, but my provider says JWNR2010v5 (N300 wireless router) will not support 100 Mbps internet connection speed in LAN. Is this true? that which is the maximum speed of JWNR2010v5 for the LAN support. I don't mind the wireless speed, I use the maximum LAN. Thank you in advance.

  Your provider is correct. Either move your router to a router which supports! 000Mbps (MGI) LAN and WAN ports or stay at your current speed Interent.

  http://www.downloads.NETGEAR.com/files/GDC/datasheet/en/JWNR2010v5.PDF

• Multiple VPN connections using 871 router

  Hello

  I have the cisco router 871 at the site of the retail that connects to the corporate site. I also want to connect a device to the sharing network partner, but it needs to connect to their virtual private network.  Is it possible to configure the 2 VPN connection to 2 different company sites in this scenario?

  Thanks for your help.

  Umesh.

  Hello

  You can configure multiple VPN tunnels on the router (whether on the same interface or different interfaces).

  You can then perform the traffic from a tunnel in another tunnel, if you must do the same.

  Federico.

• 3030 router Cisco LAN to LAN VPN, can only mount router tunnel

  I am unable to raise atunnel from inside my VPN concentrator 3030 (IOS 3.5.2) tunnel 3 uses Ethernet as the side private tunnel. Is there some kind of problem on the VPN 3030 internally that does not use the Ethernet IP source 3? Once triggered on the remote side, the tunnel passes and receives traffic and I can ping devices on the remote side of my private network, but I can't ping any remote device from inside the VPN 3030.

  Do you mean that you can now view the tunnel of something related to the 10.255.0.0/24 network, but no ping comes from the VPN3030 itself?

  When you ping the VPN3030 it will automatically use the private IP address I think. Debugging isn't warning us whatever it is the first that you attached is where the Diffie-Hellman group was incompatible. If you have passed Phase 1 but, you will see a debug on the router that is similar to the following message:

  * 26 Nov 08:51:37.901: IPSEC (validate_proposal_request): part #1 of the proposal

  (Eng. msg key.) Local INCOMING = 204.74.161.161, distance = 216.34.168.148,.

  local_proxy = 10.1.215.0/255.255.255.0/0/0 (type = 4),

  remote_proxy = 10.255.0.0/255.255.255.0/0/0 (type = 4),

  Protocol = ESP, transform = esp-3des esp-md5-hmac,

  lifedur = 0 and 0kb in

  SPI = 0 x 0 (0), id_conn = 0, keysize = 0, flags = 0 x 4

  Here you can see that the remote_proxy is 10.255.0.0, which shows that the 3030 uses this network as the source subnet. If you try and ping from the 3030 again run debugging, you will probably see the 172.16.0.0 (the private interface) as the remote_proxy.

  Why is it important that you cannot bring up the tunnel within the 3030 anyway? When would you like to do this?

• IOS router with several groups of VPN

  Similar to a discussion, I read with a PIX firewall, I need to set up multiple VPN groups on IOS-based router to support different levels of security. For example, a VPN "GUESTS" group would only have access to 1 server, while the VPN "ADMIN" group would have access to the entire network.

  With a PIX firewall, you can simply specify additional group names (for example "group1 vpngroup',"vpngroup group2"and so on). However, I have not been able to find how do with IOS-based router (Cisco 831 12.3 (4) T) running.

  For example, I have these dynamic groups of VPN:

  the crypto isakmp client configuration group of GUESTS

  password1 keys

  DNS 10.1.1.1

  swimming POOL1-IP pool

  Configuration group customer crypto isakmp ADMIN

  key password2

  DNS 10.1.1.1

  POOL2-IP pool

  ! - Users get authenticated to a RADIUS server

  list of card crypto CRYPTOMAP customer VPN-USER authentication

  ! - The problem is that line taken out. "I can only specify an allow list (a group name) for this encryption card!)

  card crypto CRYPTOMAP ADMIN isakmp authorization list

  I did research on this site, Google, usenet and ORC and have not found what I'm looking for. Any ideas?

  Thank you.

  Command 'isakmp authorization list' you do it reference does not refer to the VPN group, it refers to a whitelist of AAA name which States that the groups are configured locally. Change to the following:

  AAA authorization groupauthor LAN

  card crypto isakmp authorization list groupauthor CRYPTOMAP

  The "groupauthor" is just a label that matches the encryption to the aaa command. Your clients VPN will be accompanied to a specific group depends on what group name, they set up in their VPN client.

  See http://www.cisco.com/en/US/tech/tk583/tk372/technologies_configuration_example09186a0080095106.shtml for details, it's a HW 3002 client to a router but the router config is exactly the same thing.

• With the support of IKEv2 VPN server configuration

  I'm putting my pc W7 as a VPN server with the support of IKEv2, but it escapes me, although I am not a novice.

  I read a lot of forums "directions for use", but no address really details.

  (1) for IKEv2, I need to install a certificate... I could not find a step by step guide.

  Everyone for help...?

  (2) how to set up the VPN server on my local LAN for testing to exclude router firewall etc... and connect my 920 lumia.

  Everyone for help...?

  Hello

  My apologies for the delay in response.

  For that matter on the VPN with IKEv2 Server Setup, you will need to post your request here on the TechNet forums.

• Routing with Cisco ASA 5520 VPN

  I have installed IPsec vpn remote users in the Cisco ASA 5520 using RADIUS in my main network. Works very well. I have a site to my Cisco ASA5520 tunnels going to other sites, some of the tunnels have Cisco ASA and some have SonicWalls. I wish that my users VPN remote IPSec to be able to navigate in these tunnels is a site to access remote subnets attached to these tunnels. Do I need to use a combination of routing and the ACL? Or can I just use ACL only? Or just use routing only?

  Thank you

  Carlos

  Hello

  The key to set up here is the two ACL of VPN L2L end points that determine the 'interesting' traffic to connect VPN L2L. You will also need to confirm that the connection of the VPN Client is configured so that traffic to the remote sites have sent to the connection of the VPN client. There are also other things that you should check on your ASA plant

  Here most of the things you usually have to confirm

  • Set up 'permit same-security-traffic intra-interface' if it is already present in your configuration
    • This setting will allow connections to form between the hosts that are connected to the same interface on the ASA. In this case, applies because the VPN client users are connected to the interface 'outside' of the ASA and also remote sites are connected to the ASA to "external". If the traffic between the remote VPN Client and VPN L2L sites will be to enter and exit the same interface
  • You will need to check how the customer if configured VPN connection. Split or full Tunnel tunnel
    • If the connection of the VPN Client is configured as Split Tunnel then you need to add all the networks from the remote to the Split Tunnel, so that the connections between the VPN Client is transmitted to the ASA and from there connections VPN L2L
    • If the connection of the VPN Client is configured as full Tunnel, then there no problem that all traffic is transferred to the Client VPN connection all its assets
  • Define the VPN pool in the ACL of VPN L2L
    • You should make sure that the pool network VPN Client is defined in the ACL that define 'interesting' traffic to connect VPN L2L. So, you need to add the pool VPN VPN L2L configurations on the sites of Central America and remote control
  • Configure NAT0 / NAT exempt for remote VPN Client to L2L VPN Site traffic at both ends of the VPN L2L
    • You must ensure that the NAT0 / exempt NAT rules exist for the VPN Client for Remote Site traffic. This will have to be configured on the SAA "outside" interface. Format of configuration varies naturally a bit on the ASA Central his software level.

  These should be the most common things to set up and confirm for traffic to flow between the VPN Client and Remote Sites

  Hope this helps please rate if yes or ask more if necessary.

  -Jouni

• In order to get several features of tab line do I downgrade to the version of firefox that supports one applications below?

  I want to show the tabs on multiple lines in firefox.

  While Firefox allows you to have as many tabs that you want to open at any time, if you exceed the width of the screen, you will then need to scroll left and right to see. I want to have multiple rows of tabs.

  In order to get several features of tab line do I downgrade to the version of firefox that supports one applications below?

  What are the best options for several features of tab line?

     Tab Kit - https://addons.mozilla.org/en-US/firefox/addons/versions/5447
     Tab Mix Plus - https://addons.mozilla.org/firefox/addon/tab-mix-plus/
     Tab Utilities - https://addons.mozilla.org/firefox/addon/tab-utilities/
  

  Best regards
  Bubba

  Extensions 'Tab Mix Plus' and "Tab Utilities" support Firefox 10.0a1, so no need to downgrade your old Firefox 7.0.1 for an even older version.

• Wireless printer Lexmark X 4850 and a netgear router that does not connect while I can print

  Rookie PC user...

  I have a Lexmark X 4850 wireless printer and a netgear router that does not connect while I can print ggggrrrr....!
  I checked all plugs and connections, the reboot several times and am about to throw it out the window... Help!

  Hello

  Welcome to the Microsoft Community and thanks for posting the question.

  According to the description, it looks like the wireless Lexmark X 4850 printer is not to connect to the wireless router.

  Visit this link that should help you with this problem.

  http://support.Lexmark.com/index?page=content&ID=FA697&locale=en&UserLocale=en

  Note: Using third-party software or the link, including hardware drivers can cause serious problems that may prevent your computer from starting properly. Microsoft cannot guarantee that problems resulting from the use of third party software or link can be resolved. Using third-party software, or the link is at your own risk.

  If this fails to resolve the problem, visit this link and read "need help?"

  http://www1.Lexmark.com/us/en/view/printers%20&%20MultiFunction/Lexmark-X4850/CATID=cat170005-category&prodId=4145-product

  I hope this helps. If you have questions more related to Windows, feel free to post here at Microsoft Community.

• Impossible Windows 7 computer upstairs to connect to a new router that I just installed. It worked fine before.

  I changed ISP and changed my wireless routers. My computer laptop windows 7 connects perfectly, no problem. Cannot connect my desktop computer which is on the floor. IF I take my laptop it it works fine. I changed the settings secure to unsecured and it connected correctly. When I changed this back in would not work again.
  It says that windows is unable to connect to my router. I have reset my modem and router and it continues to happen... What can I do?

  original title: unable to connect to the wireless router.

  Hello

  Actually try updating your driver and disabling the network logon.

  Control Panel - network - write down of the brand and the model of the Wifi - double click top - tab of the driver - write
  version - click the driver update (cannot do something that MS is far behind the pilots of certification). Then
  Right click on the Wifi device and UNINSTALL - Reboot - it will refresh the driver stack.

  Look at the sites of the manufacturer for drivers - and the manufacturer of the device manually.
  http://pcsupport.about.com/od/driverssupport/HT/driverdlmfgr.htm

  How to install a device driver in Vista Device Manager
  http://www.Vistax64.com/tutorials/193584-Device-Manager-install-driver.html

  Download - SAVE - go where you put it - right click – RUN AS ADMIN.

  You can download several at once however restart after the installation of each of them.

  After watching the system manufacturer, you can check the manufacturer of the device an even newer version. (The
  manufacturer of system become your backup policies).

  Repeat for network (NIC) card and is a good time to get the other updated drivers as Vista like
  updated drivers.

  I would also turn off auto update for the drivers. If the updates Windows suggests a just HIDE as they
  are almost always old, and you can search drivers manually as needed.

  How to disable automatic driver Installation in Windows Vista - drivers
  http://www.AddictiveTips.com/Windows-Tips/how-to-disable-automatic-driver-installation-in-Windows-Vista/
  http://TechNet.Microsoft.com/en-us/library/cc730606 (WS.10) .aspx

  ------------------------------------------------------

  Make sure you know the details of connection to your wireless router - SSID and password.

  You lose connection when you do and have to redo your logon.

  Control Panel - Network & Sharing Center - right, click Customize - page set of network locations.
  lower left click on merge or delete network locations - REMOVE all instances of your network (and the
  others you don't use anymore) - REBOOT. Start - Connect To log on to the network.

  -----------------------------------------------------

  Check this box:

  Strange problem with Internet under Vista
  http://www.catonett.com/blog/archives/194

  Windows Vista cannot obtain an IP address from certain routers or some non-Microsoft DHCP servers
  http://support.Microsoft.com/kb/928233/en-us

  ----------------------------------------------------

  And:

  Network connection problems
  http://windowshelp.Microsoft.com/Windows/en-us/help/33307acf-0698-41ba-B014-ea0a2eb8d0a81033.mspx

  I hope this helps and happy holidays!

  Rob Brown - Microsoft MVP<- profile="" -="" windows="" expert="" -="" consumer="" :="" bicycle="" -="" mark="" twain="" said="" it="">

• L2l VPN tunnel is reset during the generate a new IPSec key

  I have a tunnel VPN L2L that resets completely, start with Phase 1, at the expiration of the timer of the IPSec Security Association.  Although there are several SAs, it always resets all of the tunnel.

  I see the following in the log errors when this happens:

  03/06/2013 12:54:41 Local7.Notice ipRemoved June 3, 2013 12:54:41 LKM-NVP-L2L-01: % 713050-5-ASA: Group = ipRemoved, IP = ipRemoved, completed for the ipRemoved peer connection.  Reason: Peer terminate Proxy remote n/a, Proxy Local n/a

  03/06/2013 12:54:41 Local7.Notice ipRemoved June 3, 2013 12:54:41 LKM-NVP-L2L-01: % 713259-5-ASA: Group = ipRemoved, IP = ipRemoved, Session is be demolished. Reason: The user has requested

  03/06/2013 12:54:41 Local7.Warning ipRemoved June 3, 2013 12:54:41 LKM-NVP-L2L-01: % ASA-4-113019: Group = ipRemoved username = ipRemoved, IP = ipRemoved, disconnected Session. Session type: IKE, duration: 4 h: 00 m: 06 s, xmt bytes: 260129, RRs bytes: 223018, reason: the user has requested

  03/06/2013 12:55:33 Local7.Notice ipRemoved June 3, 2013 12:55:33 LKM-NVP-L2L-01: % 713041-5-ASA: IP = ipRemoved, IKE initiator: New Phase 1, Intf inside, IKE Peer ipRemoved local Proxy 204.139.127.24 address, address remote Proxy 156.30.21.200, Card Crypto (L2LVPN)

  03/06/2013 12:55:33 Local7.Notice ipRemoved June 3, 2013 12:55:33 LKM-NVP-L2L-01: % 713119-5-ASA: Group = ipRemoved, IP = ipRemoved, PHASE 1 COMPLETED

  Local7.Notice ipRemoved June 3, 2013 03/06/2013-12:55:33 12:55:33 LKM-NVP-L2L-01: % 713049-5-ASA: Group = ipRemoved, IP = ipRemoved, the security negotiation is complete for LAN - to - LAN Group (ipRemoved) initiator, Inbound SPI = 0x9213bdc9, outbound SPI = 0x1799a099

  03/06/2013 12:55:33 Local7.Notice ipRemoved June 3, 2013 12:55:33 LKM-NVP-L2L-01: % 713120-5-ASA: Group = ipRemoved, IP = ipRemoved, PHASE 2 COMPLETED (msgid = b8a47603)

  03/06/2013 13:02:11 Local7.Notice ipRemoved June 3, 2013 13:02:11 LKM-NVP-L2L-01: % 713041-5-ASA: Group = ipRemoved, IP = ipRemoved, IKE initiator: New Phase 2, Intf inside, IKE Peer ipRemoved local Proxy 204.139.127.71 address, address remote Proxy 156.30.21.200, Card Crypto (L2LVPN)

  Local7.Notice ipRemoved June 3, 2013 03/06/2013-13:02:11 13:02:11 LKM-NVP-L2L-01: % 713049-5-ASA: Group = ipRemoved, IP = ipRemoved, the security negotiation is complete for LAN - to - LAN Group (ipRemoved) initiator, Inbound SPI = 0x93f9be6c, outbound SPI = 0x1799a16d

  03/06/2013 13:02:11 Local7.Notice ipRemoved June 3, 2013 13:02:11 LKM-NVP-L2L-01: % 713120-5-ASA: Group = ipRemoved, IP = ipRemoved, PHASE 2 COMPLETED (msgid = 1f6c9acd)

  Any thoughts on why she would do that?

  Thank you.

  Jason

  Hello

  Both the log messages seems to suggest that the remote end is closed/compensation connection.

  Is this a new connection that suffer from this problem or has it started on an existing connection?

  The Cisco documentation associated with the Syslog messages does really not all useful information about these log messages.

  I guess that your problem is that TCP by L2L VPN connections suffer from the complete renegotiations of the L2L VPN.

  I wonder if the following configuration can help even if this situation persists

  Sysopt preserve-vpn-flow of connection

  Here is a link to the order of the ASA reference (8, 4-8, 6 software) with a better explanation of this configuration.

  http://www.Cisco.com/en/us/docs/security/ASA/asa84/command/reference/S8.html#wp1538395

  It is not enabled by default on the SAA.

  Hope this helps

  -Jouni