Turning off the printer

Similar Questions

• All lights on screen Flash - Message - Please turn off the printer and turn it back on

  I'm fighting a problem for a few weeks now with all the lights on the display starts flashing and the message please turn off the printer and turn it back on.   HP sent me a new printer that does the same thing.  The printer is an Officejet Pro 8600.  My computer is Windows 7.  I use a Belkin 750 db wireless router.  I talked to the service the customer several times with no results.  Did a hard reset of the printer, change the SSID of the router, because I think that one of my neighbors has the same router.  The thing most effective I did was change the channel to 6 which will operate for several hours until the display starts to Flash again.  Channels 1 & 11 starts blinking after a few minutes.  I know there are other people who have had the same problem.  I'm about to throw the thing in the trash.  My last printer brand X was set up the same way with no problems.  On the network, there are 2 iPads, smart TV, and an iPhone.  Need help please!

  Super Dave

  Ethernet cable and connection with correction of the problem.  Its been 2 days and the printer worked perfectly.  Please pass this solution on your technical telephone support staff because I know that there are others with the same question.  Thanks for your help.

• Spoolsv.exe has 99% of the cpu when I turned off the printer after printing.

  Original title: spoolsv.

  I recently installed a new printer Lexmark Pro715.  Everything works fine, no problems with printing, but as soon as I put off the printer after printing, spoolsv.exe takes 99% CPU.  If I leave the printer in mode 'sleep', the problem is, but I do not often print, I prefer to turn off completely.  There is nothing in the print queue, everything else seems normal.  I can use the Task Manager to stop it, but this isn't a good solution in the long term.  I run MS Update and uninstalled and reinstalled the printer, with no effect.  It's driving me crazy.  I have Windows XP Home Edition SP3.

  From what I've read on the Internet about the print spooler using 99 to 100%, Norton is also sometimes involved as a contributing factor to a runaway print spooler for some people (where my request).

  IIRC, people would set their Norton to start a scan and when it was made, the print spooler has run amok at 100%:

  "Because I have Norton Antivirus, do a system scan every Friday night that I happened to see that the value SPOOLSV. EXE is using almost 100% of the CPU of the morning Saturday. It's the only time that it happens, so I simply stop the process in the SERVICES window, and life is good. I don't know why Norton Antivirus it triggers during the scanning process that I couldn't find anything on the Symantec relating to this site. »

  If the problem resurfaces surface, using abduction special tools on their website, you can uninstall your Norton and view the appearance of things without him - you can always reinstall again once, right?

  I disagree with Norton in general for its CPU and memory hogging and known interference with other XP processes (such as the restoration of the system), so I'd keep which in mind if the problem returns.

  A few years ago, I used to like Norton correct, but will never go back or recommend it.  Microsoft Security Essentials with it's lower overhead and footprint and some regular on the analyses at the request of the MBAM and SAS should hold your own system based on your surfing habits.  Your system will reward you with an improvement in the overall performance of the system as well.

  I can tell you that no single AV tool seems to know everyting so it is safe to use several respectable scanning tools.  Norton certainly doesn't know everything.

• LaserJet Enterprise M506: How to turn off the printing of comments

  During the summer, we had a number of works sent to our printer from somewhere outside the network which was Nazi propaganda. Work with our IT Department printers on our network have been changed from publicly in the face of a private network. Yesterday, we had a job came across this print a few characters on each sheet, until the ferry was empty. When I go in EWS and look at the log of the tasks, all it shows is printed and the time for the name of the work and the user as guest.  All other users are identified by their workstation name and their username.

  Is there a way to disable the guest user account without going through all those who have to use the printer first have to authenticate?

  Edited for spelling

  I don't know if this is possible.  What happened is a person on the network loaded a print driver and used your ip address, by mistake, or whether and his work has been sent to your printer with the incorrect coding resulting in all pages. One thing if you can work with your service COMPUTER is loading your printer by using the host name (the host hame can be changed to what you want it to be) rather than ip address. This way your printer can have any just like ip address any computer when it connects to the network and because this will change most of the time to turn the printer off and then back to this topic in most of the cases will prevent what is happening now.

• My computer freezes when I turn off the printer. HP D7360, Windows Desktop.Photosmart 7

  When I turn my printer off the computer crashes.  HP desktop computer.  Windows 7.  Photosmart D7360.

  I reinstalled the drivers.

  Have you tried a different usb cable? It could be that the usb cable is grounded on which could be a short circuit in the usb cable, or the printer port. Although it is also possible that this is the USB controller on the motherboard of your computer to try another cable is fixed not try with another computer if possible. If the other computer does not have any problems, then it's HP desktop computer. When you do that, you are out of my field of expertise friend . (In other words, if this does not work, try your luck on the forums of office or by calling the 1-800-474-6836)

  I hope this helps!

• print allignment page all-in-one HP PSC 2400 turns off the printer features

  After changing the ink, trys to printer to run printerr allignment.  It feeds the paper to halfway through, then hangs up with all the flashing lights.  I can use the printer on the computer, but the lights blinking and I can not copy or scan using the controls on the printer, my son found a solution a bit backward, but we didn't copy it down. Any help is appreciated.

  After changing the ink, trys to printer to run printerr allignment.  It feeds the paper to halfway through, then hangs up with all the flashing lights.  I can use the printer on the computer, but the lights blinking and I can not copy or scan using the controls on the printer, my son found a solution a bit backward, but we didn't copy it down. Any help is appreciated.

  Hello

  You can get a faster solution on the Support Forums of HP printer.

  Here is a link for your convenience.

  Printers and all-in-one - HP Support Forum's:
  http://h30434.www3.HP.com/T5/printers-and-all-in-ones/CT-p/inkjet

  Select the appropriate forum for your device.

  Concerning

• the printer says"ink system failure, turn off the printer, then. What can I do?

  I bought new cartridges yesterday and installed them. This is the message I got after that

  Contact the manufacturer of the printer.  Any material support is the manufacturer of the equipment.

• E 7520 HP All - In - One Printer: turn off the power to the wireless printer

  I have not printed for a few days I have not noticed if my Wi - Fi connection worked.

  I tried to print wireless today and got the error message that the printer was not connected to the internet.  I tried to go wrong, but it did not help.  I checked the connection to the wireless router and put the password in.  It has not yet recognized it.  I tried to disable printing for my smart phone (I think it is called), but the screen froze on the circle showing the progress.

  I tried to turn off the printer with the power button, but that no longer works.

  The Wi - Fi light just keeps blinking.

  How can I disable the printer may reset?  Or can you help get my printer to recognize my wireless again?

  Thank you.

  Hi Rhonda, there.

  I would suggest to unplug the power cord from the printer without turning it off with the switch, it will do a reset without getting rid of all the parameters. You simply leave unplugged for about 1-2 minutes to clear out any power.

  I recommend then reconnect, and doing as much as you can from the guide below:

  Printer keeps no connection Wi - Fi

  Good luck and let me know how it goes

• Cannot turn off the issue of jam and paper cartridge (both at the same time)

  I have a HP Officejet 8600, running on a wireless home network.  The printer will not work.  We get two messages. 1. Introduction to jam, and I'm going through all the steps to clear paper, including the search for pieces of paper, as well as any leaves.  I found no paper, whole or in part anywhere in the printer.  2. at this point, I get a message that I have a problem with a printer (of ink, installed correctly, etc.) cartridge.  Simply replace us all cartridges, so I know that we are not out of ink.  However, when I opened the door to the area of printer cartridge, the cartridge does not move where I can check it out.  There's just right.  So I'm "stuck".  I don't know how to get the cartridge door to roll over so I can check!  I turned off the computer several times and tried to reset things, but nothing seems to work.  Any suggestions?

  Followed - I turned off the printer.  Then opened the cartridge and reaches into the printer access door.  Without moving the cartridge door, I pressed each cartridge to make sure it was placed correctly.  Then, shut the door and back running the printer.  The printer seems to start correctly.  I then opened the door, the door-cartridge moved where I could access them normally.  I double checked that each cartridge is installed and closed the door.

  At this point, everything seems to work properly.

• Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running.

  Somewhere, I messed up my permissions, turn off the computer to see if it helped, now will not start at all. The start bar stops a quarter turn along. I tried in SafeMode as well do. I ' on a Yosemite iMac running. I can't enter to give more details. Can anyone help? There are a load of work due to deliver to the printing press Monday

  Have you tried to boot from the Partition Recovery and repair then the disc from there, using disk utility?

• OfficeJet HP 6968: officejet hp 6968, turn off the ringer

  Is it possible to turn off the ringer on an HP Officejet 6968?

  Thank you

  Hello @Kathieh3,

  The steps I have mentioned must be done on the printer screen, not on the computer.

  On the printer screen, press 'Fax'-'settings'-'fax advanced settings'. Once you scroll through the menu options, you will find the "ringing" or "ring volume" option. Select, then reduce the volume.

  Let me know if that helps!

  Please click on 'acceptable' on the post that solves your problem to help others to find the solution. To show gratitude for my help, please click the 'Thumbs Up icon' below!

• After the update to el Capitan my iMac will not be asleep. I put it to sleep and turn off the mouse and keyboard that goes with it, and 5-10 minutes later, he wakes up on his own. Now, I have to stop it after use and each time only. Major pain

  After the update to el Capitan my iMac will not be asleep. I put it to sleep and turn off the mouse and keyboard that goes with it, and 5-10 minutes later, he wakes up on his own. Now, I have to stop it after use and each time only. The Major pain. Any help would be greatly appreciated.

  Please test after taking each of the steps that you have already tried:

  Step 1

  Take all of the measures suggested in this support article, including those under the title "If the previous steps do not work." It is the starting point for a new effort to solve the problem.

  Note that, as stated in the article, the computer will not sleep, if some sharing services are enabled. In the menu bar, select

   ▹ System Preferences... ▹ Sharing

  Disable all sharing services.

  Step 2

  If sharing music iTunes home sharing is enabled, disable it or quit iTunes. Do the same with third-party applications that have a similar feature.

  Step 3

  Select

   ▹ System Preferences... ▹ Accessibility ▹ Speakable Items: Off

  Step 4

  Select

   ▹ System Preferences... ▹ ▹ Advanced Bluetooth...

  and uncheck the two boxes marked

  Open Bluetooth Setup Assistant at startup if...

  Step 5

  Reset the printing system.

  Step 6

  Back up all data.

  Triple-click on the line below on this page to select, then copy the text to the Clipboard by pressing Control-C key combination:

  /var/vm

  In the Finder, select

  Go ▹ go to the folder...

  from the menu bar and paste it into the box that opens by pressing command + V. You won't see what you pasted a newline being included. Press return.

  A folder named 'vm' should open. Inside, there may be a file named 'drag '. Move this file and only this one in the trash, but do not yet empty. You will be asked for your password. Close the folder window.

  Restart the computer and empty the trash.

• turn off the ringer on the envy 7640

  I'm a new 7640 attached to a 2013 end Yosemite running iMac. My wife works from home and I would not have the ringtone on the sound off printer when a call comes in. Is it possible to turn off the ringer, as you can do on a phone?

  Hi @Neilkn,

  Welcome to the Forums of HP Support! I read your post and see that you want to turn off the ringer on the printer. I would like to help you today. If this helps you to find a solution, please click on the button "Accept as Solution" down below in this message. If you want to say thanks for my effort to help, click on the 'Thumbs Up' to give me a Kudos.

  I've provided the steps to disable the volume of faxes. Hope that helps.

  • On the printer, go to Fax settings.
  • Select the Fax Volume.
  • Select disabled.

  If there is anything else I can help you, let me know. Thank you.

• I need to know how to disable the test print cause everytime I turn on the printer prints featured.

  I need to know how to disable the test print cause everytime I turn on the printer prints featured.  It is hp1315 series.

  Hello

  If you want to disable printing test page, you must check with the manual of the printer. Try the steps from the following link:

  An alignment Page prints whenever the all-in-one is turned on or off or a print job is started
  http://h10025.www1.HP.com/ewfrf/wc/document?DocName=c01336397&cc=us&DLC=en&LC=en&product=1146336&tmp_track_link=ot_search

  I suggest you to contact HP for better support.
  http://h30434.www3.HP.com/T5/printer-all-in-one-software/BD-p/software

  Additional information:
  http://h20000.www2.HP.com/bizsupport/TechSupport/document.jsp?objectID=c01577197&lang=en&cc=us&ContentType=SupportFAQ&prodSeriesId=360489&prodTypeId=18972

  Printer in Windows problems
  http://Windows.Microsoft.com/en-us/Windows/help/printer-problems-in-Windows

• 8500 HP OFFICE JET PRO 8500 A909n error: B87126D0, unit will not turn off or print

  I'm having the same problem as described by others, "error of 8500 HP B87126D0, unit not turn off or print.

  I followed all the instructions from documeneted on this thread. I also replaced the power Module, in the hope that would solve my problem. I have an OFFICE JET PRO 8500 A909n PRIME

  Not sure why the solution cannot be posted here, as I see many others with this same error and the exact symptoms.

  Whatever it is, I really appreciate a solution 'private' as well.  Really, I love this printer and would rather not have buy another.

  Thanks in advance!

  Hello @rnegron57,

  Welcome to the Forums of HP Support! I see that you have found an error code on your HP Officejet Pro 8500 first, you are unable to power the printer on or off.

  You have completed the recommendations online without success, and you've seen other members of the community receive private messages. I would like you to take a look here: printer resets: What You Should Know

  I went ahead and you sent a private message, please go to your user page to the right of your name, you will see your Inbox.

  I'll watch for your reply, I would like to know the results.

  Thank you for being a part of the community of HP. Please let me know if this helps solve the problem by marking this message as "accept as Solution" . If you need more assistance let me know and I will gladly do whatever I can to help. If you want to say 'Thank you' to my effort to help, click on the "thumbs up" to give me a Kudos.