Two fans of processor on my p30?

Similar Questions

• Two fans at the same time come on the Satellite A30?

  Hello

  I ve just replaced my camera laptop mobo (2 fans) and I m sure that when I tested after all together put two fans of kicks in, but as I m sitting here write that I can t see or feed the second fan lights.

  I m worrying as when I took part I noticed that one of the connectors to the original fan was half way out - I guess it happened when I paid someone to repair my laptop, there is a year (I had to do it myself now and I ve felt m tech didn't know what he was doing) however I am a little concerned that maybe the second connector unit fan slipped out and this would explain why the second fan does not come when the first made?
  ID rather not disassemble it again to check if not I need to.

  Oh I've had a thought they are both controlled by temperature (they are of course) but are they set to start at different temperatures?

  Adding: chezybezy

  I m not an A30 owner but I guess that the two fans should start and run at the same time
  There are two power cables and I guess that both fans are ordered together at the same time

• Satellite A10 - problem of the fan and processor speed

  Hello

  Recently, my computer stops and overheated while clunked there fan who told me that I had to clean the fan and the heat sink. I have it done, replaced everything and then turned back on my computer. The fan seems fine now except that it only lights up for about a second and a half and then cuts off. While the computer on, it is not overheating but the fan just trying her continue again and again and again and turns off after a second or two. I think to compensate, the computer is running only a percentage of its capacity because on top the fan doesn't work does not correctly, the computer is running about 50 percent more slow it was 10 seconds before it overheated.

  When I replaced the fan, I noticed that the card that turns the fan was wobbly, which would have something to do with it?

  Assistance, alternatives or insight would be extremely appreciated.

  Best regards, Niko

  Hi mate,

  In your case, it could be that the fan cable to the motherboard could be defective. Thus, you´ve has already removed it, just so it again, remove the fan and check if the cables and connectors are OK.

  If the fan or the cable is damaged, then replace the fan. IMHO the bearings could be faulty too, so it's another reason to replace this fan (and the fan is really NOT very expensive)

  If you need some parts, google for or ask an authorized parts service center:

  http://EU.computers.Toshiba-Europe.com/cgi-bin/ToshibaCSG/generic_content.jsp?service=EU&ID=ASP_SUPPORT

  Welcome them

• fans of processor for mother HP tips

  guys, I bought a new processor for my office, and it fits very well apart from the fan discovered her because it's a motherboard of hp.

  now I need to find a fan that matches a motherboard of hp and which is the right one for my new processor. to help you?

  Look over the PM I sent you.

• How to order the two fans for vista

  How to do for fans to order both for my family vista premium, erro messages get that fans do not work

  Need to know how much cost fans

  Hello

  What could you mention the model number and product of the system for which you want to buy the fan.

• Having a problem with vmotion between two hosts with processors Intel E5640

  Hi all.

  We organize a group of 14 guests, each with ESX 4.0, build 261974 installed.

  They are managed through vCenter 4.0.0 and construction 258672, vSphere client 4.0.0 builf 258672.

  The hosts are blades from IBM, in a BladecenterH.

  Some of the blades are older model HS21 (type 7995) with processors Intel Xeon E5440.

  The rest of the blades are more recent model HS22V (type 7871) with processors Intel Xeon E5640.

  We are currently replacing old HS21 blades with more the HS22 blades, so we just bought 7 HS22s, all with the same Intel E5640 processors located in the blades currently in service. One of the things that this transition will happen for us is allowing us to have the same processor type in all of our blades and remove vMotion compatibility problems we had in the past. We were unable to turn on CVS, because we would have had to shut down a cluster of virtual machines on the latest hosts and could not take this kind of failure. We will turn VCA after that.

  Here's the question:

  We just installed the first new knives, and when turn on us and try to vMotion VMs to it, it fails. He gives us the error standard vMotion on CPU register incompatibilities, and that we should read kb1993. The thing is, they all have the same processor. Same identifier type, same everything, yet for some reason vCenter is convinced they are incompatible. We checked things in BIOS, and they are all the same.

  We are ideas, other than the new knives have a later rev BIOS than the old ones.

  Any thoughts?

  Thank you!

  -Tim

  According to the missing pieces, http://www-947.ibm.com/support/entry/portal/docdisplay?lndocid=MIGR-5086963 should help you solve the problem.

  André

• My T7910 came with two bays of processor

  It appeared earlier and I looked inside and of course it has 16 bays of memory and 2 beautiful large bays of processor rather than one that told me to wait with my single purchase of an e5-2650 v3 and 32 GB DDR4 4x8chips XEON Proc. I know tells you all about the goal then I would be surprised and happy right EXTRA? :~) . (I choose to believe that).  :) I was right, because why a unique model number would mother many styles on board!  Different CHIPS maybe but not motherboard! They would just give different number model, 7900 7920 or, with a number of type 7911-has been revised. Otherwise, it would be a nightmare to replace a motherboard. Dell rocks...  More beautiful Machine. that I never set eyes.  I used to own a Convertible PC of Tabler by ASUS called a R1F, when it was released it was called "The LAMBORGHINI of Notebook computers" - well, I gave this Tablet PC to my little nephew to have a computer of his own in his room, and now I have re - claim this expression to invent a nickname for the T7910; my new computer switches! Didn't come with much else though...  None of the drives. (I hope that this optimization of Dell for Autodesk 3Ds Max software, they talked, is on the Dell.com site.  There is the Windows key, so all I need is a disc to install Windows $10...  I asked; a DVD of resources as well as the Energy Star AND one of the "change 5.25" to 2.5 "bays free install Kits. But I hope that if they send a Correct Power Supply, etc, the kit of disk resources and 2.5 "can come with it. (no idea if they are welcome?  up and down, they promised that the Energy Star Option would be included before shipping...  I don't want the "Chrism" bug - if he's out and about he will see this and answer, otherwise he is held in any case...   I'll give you tech a call now that I have a sticker (somewhere) that apparently allows me to get to them for the first time again.) (which should make a difference, I hope.). On the Energy Star 6 option... Maybe if I ask you once again, someone can answer and not tell me that I'm not allowed to know because all the information "are owners'., (so they said right before the last dark ages,..): what I'm now missing (in terms of Energy Star compliance), they said they would put in and didn't?  It IS JUST the power SUPPLY? or the whole of the machine that receives Energy Star treatment and I need this credit to return completely to start again for the sake of a 'unique' CHECKBOX. ' They ' (tech chat etc.) says that a power supply could be easily "cross-shipped. I hope that this is the case.  I have not really met someone at Dell that could actually change or fix anything, except the person who says they were my person point (and 100% ensure that my machine is a not ship without Energy Star compliance...)   Well...  Maybe the Tech Department are all the RockStars and everything will be Fine. Other than the relatively small omission of a disk, cables and energy star, OMG Wow its GREAT. The best research machine EVER! NOW, I just have to hope is not not a MANNEQUIN PROC PORT and 8 additional dummy DDR4 ports!  LOLOL (they don't put much more metal on a false port!)  I'm so tempted to look under the hood of protection proc to see if there is a badge or million.  (Maybe when I do a video Unboxing 3D tonight later, I'll do it!) OH Yes, I'll do a video UNBOXING to prove that it is amazing how and to help people in a situation like mine (for love or money) is not found on a SINGLE FACT REAL on this MEGA-MACHINE before, during or after the command!  All my * life I have always corrected and help tech departments and not once I don't call any Department tech, I was helped before so I can understand the problem myself and teach THEM the fix (no not that none of them ever ready attention or he wrote LOL) BUT I have NO experience with DELL technicians so far (as I just got my Service Code on my machine)?) so I quite keep out hope and suspend judgment (of course).  Maybe they are the very cool tech guys who are proud to be uber-nerds (like me!) and technicians and in love with their line of the professional tools like today already Fine am!  WHAT A MACHINE! Thanks to those who have tried to help. its perfection!  maritime transport (it is out of LAND anyway?)   I was so counting on him to come next year and I would have the time to make sure that they solve these problems, I've had with the selection of what I wanted in this control system crazy automated online that indicates what you can and can't buy (?)  and then the lack of assistance order placed on the 'tech' cat, which wasn't all that too...  Saying: I wasn't buying a computer at home (her sitting on my BED right away in its box) and they can not help me even if the offer 'click for instant help' dialogue popped up ON the order of T7910 page to halfway through ordering process. Any all this good things.   I can say that it is the best machine I've ever seen.  Surely, they want to go to the final. 01% more in order to make what I have planned and called for!

  Hi Robert3d,

  I am pleased to hear that the system has so far been to the height to your expectations.

  Good luck with the new PC!

• Qosmio X 300-130 and Linux - GPU fan does not turn

  Hello

  I recently I changed my windows form of os for linux... and I realized that my gpu fan not spinning.
  eventhought it spinned in windows.

  When I turn on the pc two fans that the processor and the fan GPU continue until I connect to linux and then the GPU of the fan stops... and the GPU GET VERY HIGH TEMPERATURE

  Please it is urgent

  What do you recommend?
  I think it is driver related.
  THANKS IN ADVANCE :)

  Qosmio X 300-130 (PQX32E)

  Hello

  Use the following command to get information from the ACPI:
  dmesg | grep - I have fan

  From my point of view of the rare, the fans are controlled by ACPI and this allows to work with the BIOS to monitor the temperature of the core.

  The different distributions like Debian or Ubuntu Linux supports a fancontrol script (the latter can be downloaded separately) that can be configured to handle the speed of the fan.

  In addition I would also recommend to upgrade the Linux kernel if possible.

• fans of zv5000z

  I have a hp zv5000z I can say that one of the fans is not working.  Is it possible to test the other fan to see if it works? Is there an article step by step on how to clean the fans?

  I've owned a zv5000z and I think she can still hold my personal record for the laptop that I owned the longest. about 3.5 years. I sold it to a family to give their teenage son and he wrecked it within 30 days. Another story. At the time that I bought the girl was considered a player. 64-bit AMD Athlon and a nVidia GeForce graphics card. I had Windows XP 64-bit on it and 2 gigs of RAM together.

  Here is the Manual:

  Manual

  Simply follow the instructions for disassembly down to the motherboard and the withdrawal of the processor. Look at point 7 on page 3-3. Fans are integrated in a sort of large insert module like a piece of cheese in a "sandwich". See Page 5-75. Keep in mind this manual covers several models, and sometimes it is a little confusing. Its a laptop big and there is a good amount of clearance in there, but also a lot of parts and subsets and lots of screws to follow. You certainly want to remove top the processor and the heat sink and apply new thermal paste sparingly. Just on the processor core. Clean the blades on the two fans with a q-tip and rubbing alcohol and let it dry. The dust that accumulates on the fans that makes them rotate more slowly and move less air.

  If both fans are working there is no substitute to keep the vents two fan up to your ear or just simply watching them to see if the blades begin to turn. If I remember the second fan does not hit unless you put the load on the processor. So do something like defragmentation of the hard disk or play a game and it should so this second fan on. I think that model also uses the old processor driver AMD Cool n Quiet and you want to ensure that is installed.

  If it's 'the Answer' please click on 'Accept as Solution' to help others find it.

• Error: Failure of CPU fan

  The original motherboard was not on my Pavilion a6528p. I got fed up with accidents several blue screen whenever I started to use it. Once he ran for a while (an hour or two), he has generally kept running. Worked to try to eliminate the virus/malware (multiple programs found no no), the memory test (used memtest86 +, ran all night without fault), CPU test (Prime95 torture test used, ran all night without fail) decided to try another motherboard. Not able to find a new, so decided to take a chance on a used.

  The jury used (so far) has never crashed. It is therefore a good thing. However, every startup I get the message "ERROR: CPU fan failure! Press F2 to continue to start. "I believe that this message is incorrect because I ran Prime95 torture for hours test and the temperature of the Processor reported by CPUID HW Monitor program is around 52 degrees c for each carrot. When I run Prime95 torture test, the temperature of the CPU are much lower, around of 38 degrees C.

  The HP support document http://support.hp.com/us-en/document/c00013522 describes in detail by selecting Hardware Monitor in the Advanced BIOS menu. There is no choice in the latest version of the BIOS, I installed on the HP website, which identifies as BIOS Version/Date American Megatrends Inc. 5.43, 10/09/2009.
  
  Because the help document is incorrect and no help, someone has ideas how to eliminate this message CPU Fan has failed, what happens whenever I start the computer?

  JimK Hello,
  
  Not all BIOS versions have the same settings and you're right that your BIOS is not this setting. Looking at what the settings you have (http://goo.gl/1mCvq) there is no parameter, you can change even not to ignore the message.
  
  The motherboard doesn't like not the CPU fan that is currently installed, if the fan is not mounted in quick power enough, do not provide enough cooling, or is simply not sufficiently powered is unknown, nor can it be determined. You can try to unplug the CPU fan and reconnect to ensure a solid connection. Probably, you should be able to say that the CPU fan turns so you can figure out if she has no or not enough quickly.
  
  Your options after that are to
  1. process by pressing F2 at startup to work around the error
  2. try another fan for processor to see if you can get the motherboard like.

• HP ENVY dv6 Notebook PC replacement fan part number of

  I need to know what part to buy to replace the fan. I get hp fan 90 b error message that says that my fan is not working properly. A month ago, it started making loud noises. It still works, but I want a replacement nearby is not installed until the thing decided to die for good.

  HP ENVY dv6 Notebook PC

  Series No.: [edited by Moderator serial number]
  Product #: B6C70AV

  Thank you!

  Hello:

  Because your model is a CTO model it does not give material specifications.

  You need one of the two fan-heatsink for Intel based motherboards, found in Chapter 3 on page 29 of the owner's manual.

  http://h10032.www1.HP.com/CTG/manual/c03591281.PDF

  However, it is very easy to understand than you need...

  If your laptop computer is the AMD / switchable graphics of Intel you need of this fan/heater:

  For use only on the computer models equipped with an Intel processor and a graphics subsystem with discrete memory

  HP Part # 682061-001

  If your laptop has Intel HD graphics card, you need the fan/radiator:

  To be used on the computer models equipped with an Intel processor and a graphics subsystem with UMA memory

  HP Part # 682060-001

• How can I change or control the fan speeds up my computer?

  my processor and motherboard run hot. the fan for processor speed is 20%, the other two are 30%. How to increase the fan speed to lower the temperature?

  I would not try to change the speed of the CPU fan. Clean the case out if its full of dust (if it's a desktop computer). If you can put more fans in the case, put more fans in it

• DV6-6198sp: what fan is best to use with hp dv6-6198sp?

  The laptop is originally a dv6-6153ea, but I upgraded the card motherboard and CPU than a dv6-6198sp,

  He now has an ati 6770 and a core i7 2670qm that i need to keep cool

  Time reach 95 on charge which according to me is not bad!

  I have two fans that I have access, a sunon and an adda, both are the same shape, but it is not of this laptop.

  The sunon cooled by a core i5 processor with a gpu 2410 6490

  The Adda cooleda core i3 with an unknown gpu fan (I can't remember sorry!)

  So what I need to know, is what fan would be better suited?

  The Sunon is a .4w and the Adda is a .5W so I was under the impression of the Adda would be better...

  But if someone could give me some more information on that would be great as I am really stuck now!

  Thank you!

  Hello:

  I had studied your question - the HP part number displayed above your "dv6-6153ea updated' costumes for dv6-6198sp motherboard.

  The two models share the same repair manuals.

  Part of cooling fan doesn't really change depending on various Intel processors they have, but supported the graphical system by the Council.

  Concerning

  Visruth

• CPU fan failure

  I have a Compaq SR5510F and when turn it on, the error message: don't have a CPU fan.  I took off on the side of the processor, and two fans that I see are turning very well and one that is in the box also turns fine.  Is the CPU fan, one upstairs that you can not without disassemble everything?  What should I do?  Anyone else have this problem with this model?

  There are 3 fans in the SR5510F. The PSU (Power Supply) contains an extraction fan. The system fan is also an exhaust fan. The CPU fan is mounted on top of a metal radiator. The message "CPU fan has failed" is triggered by a sensor. The cause can be a dusty fan, or obstruct the fins of the heatsink or a fan that runs too slowly to dust.

  See this document

  

• Please if you have one coming 11 Pro, answer me this quick question - related /screen fans

  Are supposed to be two fans in the 11 venue? In particular the i3/i5 models?

  I noticed that I don't hear a fan, from the right wind, but on the other side is quiet.

  Also, when I have the screen displays something like XBMC or certain types of film, there is a light buzzing/grinding noise coming from the location of the vent on the left, as if he were a fan turning, but it is soft or broken. If there is no fan, so maybe it's just the sound of the screen running at high frequency - or maybe it's the wireless card?

  Thank you

  One fan and it's on the right side - where is the processor!