Type get lost...

Similar Questions

• Aftertouch message get lost?

  I have a Yamaha Motif Rack ES of Nektar Panorama P6 and iLok connected via a hub ("HooToo") USB3 generic port USB3 on my MBP.  The Mac USB2 port is connected to the Focusrite Scarlett 18i20, and another keyboard (old Korg N1) is connected to the midi in port of the Focusrite.

  I have several patches where I play the Motif Rack ES with the nectar, with Aftertouch keyboard mapped to the Modulation of the motive... setting to bring in the vibrato with aftertouch. Many times it seems that aftertouch messages get lost... Modulation will come as planned when I press harder the nectar, but often doesn't come back down again... Vibrato stays on until I have pressure and then release again. My vibe all the loot.

  Did someone else had a problem like that and maybe found a solution or workaround? I suspect that the USB hub can be a bottleneck, but I don't see any way around that.  Maybe it's the ground itself? I didn't notice messages are lost during playback of the soft synths, but I'm not sure about this.

  Try to connect the Motif Rack ES MIDI to the Focusrite.  If it solves the problem, using a USB cable on the ground by midday. It seems that I remember reading about the problems of USB communication with that of patterns and MO6s time on the Yamaha forum. USB hub is powered? Try another USB cable and a powered hub.

• I forgot my security question answer on my account and I get lost email address of relief

  I forgot my security question answer on my account and I get lost rescue address, how do I get my new security question?

  Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

• If I use different, the same computer, but an iCloud account will be my projects get lost?

  If I use different, the same computer, but an iCloud account will be my projects get lost? I downloaded the trial version to my friend with her iCloud computer and now it is expired and my project was not yet ready. If I connect with my iCloud on my friend's computer and buy FCPX, my project will be there? And if not, if I buy the program with my friend iCloud account, is it possible I could move my computer later? I would not buy an app €300 just for my friend...

  LLA libraries are separate from the application. That you have subscribed to the trial is quite distinct from what you use to connect to the purchase. However, once you bought with an Apple ID it is that you always have to sign in with to receive updates. The application and the Barrie similar don't really care what you signed in in iCloud.

• Printer get lost on cable network

  I suffer for my printer (HP OfficeJet 7680) constantly be lost. (no software can find to print to it. I can restart and it will show for a while, then he gets lost. I use Windows 7 (little) and have another Windows 7 (32 bit) on the network that has the same problem. I applied the fix for this supposed HP. Any ideas how to continue?

  Click on the 'Start' button--> printers and fax machines.
  Under print jobs, click on "add a printer".
  Click 'Next' in the Add Printer Wizard window.
  Select "local printer attached to this computer.  Deselect "automatically detect and install my Plug and play printer."  Click "next".
  Under Select a Printer Port option, select "Create a new port" and choose "Standard TCP/IP Port" and click "Next".
  In the "Welcome to the Add Standard TCP/IP printer port Wizard" make sure that the printer is enabled and configured. Click on the button "next".
  Under "Add Standard TCP/IP Printer Port" enter the IP address of the printer (normally I would put the printer is there, but you use a static IP address for the printer).  Click 'Next' and then click 'Finish '.
  Now, select HP in the manufacturers list, select your printer in the list of the models of printers and click the button "next".
  Keep the existing driver and click "next".
  Add the name of print spooler, and then click "next".
  Click "next".
  Click "Next" and "Finish."

  Print a test page.  I would like to know if it works.

• I have a Canon 7 d Mark II and I'm using Lightroom version 5.7.1 on a Mac computer. My question is, I can't get attached to my computer. Lightroom and my computer recognizes my camera, but the connection did not last long and she also gets lost and then c

  I have a Canon 7 d Mark II and I'm using Lightroom version 5.7.1 on a Mac computer. My question is, I can't get attached to my computer. Lightroom and my computer recognizes my camera, but the connection did not last long and she also gets lost connected, then lost several times until the capture of attachment option is closed. I tired buy new cables, lightrooom and call Update to Canon support, but still nothing works for me please help?

  Hi Martin,

  In order to make shooting with the Canon 7 D Mark II captive, you need Lightroom 6 and higher.

  Please visit the following link: a list of cameras that can be attached to Lightroom.

  Kind regards

  Tanuj

• help to get lost in a table of the elements.

  Hi all. I need a little help to find something.
  
  Flash CS3: LIKE 1-2.
  
  
  I've been messing around with colorTransform and it works via a series of clips, and somewhere along the way of the elements of my table started to get lost. Meaning, when I started a "trace (elementArray)" would recognize each element as a movieclip.
  
  
  Now when I test only the elements 1, 2 and 5 are recognized as tongs and others come undefined.
  
  
  Now the only thing I can think is the difference in the names for the mcs naming conventions (I shot two other files.). but that shouldn't be a problem. I checked and double checked the names of the instance and they are correct. No indication on what would be really appreciated.
  
  
  Thank you.

  Thank you for your offer to help Kglad, but I understood it.

  The code works, it was a problem with the video clips. They have been set to "track as button" so the clip of btnColor_mc has not registered.

• Ref FPGA type-def lost connection when moving to another computer

  I have a VI that opens an FPGA VI reference and links the reference to the type definition. The VI works fine on a single computer (Win7; LV 2010, module FPGA 10.0.0).

  However, when I open the same VI on another computer (WinXP, LV 2010, module FPGA 10.0.0), the checkbox for reference FPGA VI for the definition of the type of binding is not checked and, as a result, I get a cut wire when the reference enters a Subvi, which accepts the definition of reference FPGA VI as input type.

  See the below two screen captures. The picture above shows the situation on the first computer, where all is well. The second picture shows the situation on the second computer. Note the checkbox disabled in the dialog box and the wire cut on the right...

  Would could be the reason for this problem? How can I avoid it?

  BTW: I use the same VI on a couple of other computers (all Windows 7), where all is well.

  

  

  In fact, the problem was not caused by the other PC in itself, but rather by the fact that on the other PC, the application was in the directory with a different name. The FPGA VI reference type definition uses an absolute path, however, who gets broken when the application is in a different directory.

  Might be good to store the relative path in the future versions of LV.

  As a workaround, just use the FPGA VI reference in dynamic mode.

• Installation of IE9 causes my wireless to get lost

  Original title: IE9
  Once IE9 lost wireless network installation, System Restore and wireless operational again.  Still have IE 8 because of the wireless problem.

  Hello

  1. don't you make changes on the computer before the show?
  2. what anti-virus is installed on the computer?
  3. you receive an error message?

  Method 1:
  You can try the steps in the link and check.
  Windows wireless and wired network connection problems
  http://Windows.Microsoft.com/en-us/Windows/help/wired-and-wireless-network-connection-problems-in-Windows

  Method 2:
  You can temporarily disable the antivirus and firewall on the computer and check.

  Enable or disable Windows Firewall
  http://Windows.Microsoft.com/en-us/Windows-Vista/turn-Windows-Firewall-on-or-off
  NOTE: turning off Windows Firewall may make your computer (and your network, if you have one) more vulnerable to damage caused by worms or hackers.
  You can see the following link to disable the Antivirus installed on your computer software.
  Disable the anti-virus software
  http://Windows.Microsoft.com/en-us/Windows-Vista/disable-antivirus-software

  NOTE: Antivirus software can help protect your computer against viruses and other security threats. In most cases, you should not disable your antivirus software. If you need to disable temporarily to install other software, you must reactivate as soon as you are finished. If you are connected to the Internet or a network, while your antivirus software is disabled, your computer is vulnerable to attacks

  Method 3:

  You can uninstall and reinstall the network card.
  a. Click Start, type device manager in the search box of start and press ENTER.
  b. Locate the network adapters and expand the same.
  c. Select the wireless connection, right click and choose uninstall.
  d. restart the computer, if prompted.
  Pilots should settle automatically after the computer restarts.
  Now you can install the latest network card drivers and see if that fixes the problem.
  See the link
  Update drivers: recommended links
  http://Windows.Microsoft.com/en-us/Windows-Vista/update-a-driver-for-hardware-that-isn ' t-work correctly

• After refreshing win8 how get lost return programs?

  After refreshing win8 I lost several programs important and got Mc fairy back instead of Pro-Avast, how to make the change?

  All programs and apps not installed in the store are eliminated by design. The only way to get these back comes from rei8nstall the original media or the web site. Hope this helps and if you need any additional aid station and we will be happy to help you.

  The above opinion is mine and does not necessarily reflect that of Microsoft, it's employees, or any other Member of this forum.

  "When we try to take anything by itself, we find it hitched to everything else in the universe."-John Muir

• How can I get lost bios password?

  How can I get my lost bios password or a hobby no matter... .to model vpceg25en

  A support representative can help you with your BIOS password.  For reasons of security and to ensure that only the legitimate owner is granted access to the computer, a copy of the proof of purchase will be required at the time of the call.

  For more information about how to contact a Sony centre in another country, please visit the following site.

  http://www.Sony-Asia.com/countryselector.html?HPID=countryselector:AsiaPacific

  If my post answered your question, please mark it as "accept as a Solution.

• Get lost with the controls on the panels

  Hi all,

  With the help of Lavwindows 2010

  I have a little difficulty with my UIR.  I inherited a project with several panels, 2 have about 340 controls on each of them, I'm looking at (for example) a certain (RATE) control properties. I use the tree Panel to get the table I want and the FREQUENCY control.  I double click on the name of the control RATE.  In the details (under the tree Panel) section, it shows the name of the constant is MLED_MAX12_2 and its status led (its really a digital slide).

  Is it just that CVI has trouble with panels containing a large amount of controls?

  Is there another way for me to access this control? (right click on RATE and by selecting OBJECT UI FIND gives me the properties of the control MLED_MAX12_2.

  Is there a limit to the number of controls on a Panel? of the project? File of the UIR?

  Thank you

  Pete Hedlund

  I couldn't reproduce it in 2010 SP1, so I tried in 2010, and I could reproduce the bug. This problem has been fixed in 2010 SP1.

  http://zone.NI.com/DevZone/CDA/tut/p/ID/12323#290057_by_Category

  The solution is to change the control in the edit control dialog box that appears when you click on , when a control has focus in the editor the user interface with the editing tool selected (as opposed to the tool of exploitation). Or you can double-click the control to display the edit control dialog box.

• Cursor gets lost while typing

  Original title: problems with typing

  whenever I type in the emails and documents, my cursor jumps around on the page and I have to keep retyping and correction.  suggestions?

  Try a new keyboard.

• Who should I contact to get lost connection to the eprint centre information?

  I'm stuck.  The system recognizes my email address but not the password.  When I click on "lost password", it asks me to submit the email associated with my account and goes no further.  What I am doing wrong?

  Hi dgcrawf,

  You can always contact HP Cloud Service Support directly by calling 1855-785-2777.

  Recently HP merged a few sites including snapfish with eprintcenter and this site because of some problems for some users. You will need to do is go to www.snapfish.com and click on forgotten password and change it. Then, you should be able to go back to your eprintcenter.com site and connect you using your email address and the password you changed just to snapfish.

  Let us know if it works for you or if you need anything that anyone else.

• Disable the accessibility controevery time I type get other characters/letters

  Original title - disable accessibility ocntrol: whenever I type o, t, or something else in the e-amil or Word, change fonts, zoom in/out, web seatch opens,... while I can't type a simple sentence without tampering with.

  I can not nothing type Excel, Word, e-mail, or even without having tampered with unwanted aid. In other words, if I type O, help appears to open a file, or Google search engine will appear. Type T, then justification changes to the parameters of the right to the Center, or a warning informs you that the "passage to the text will lose something." Type I and the italic font changes. Type P and print menu appears. Display zoom in and out and I could not find on what triggers it but very annoying and time consuming. According to me, it has something to do with the control of accessibility. I tried to disable all nothing doesn't.

  Hello songshoreline,

  You have probably enabled inadvertly StickyKeys. Look at the Microsoft Web page on shortcuts for accessibility for the keyboardhere. The article describes how to enable and disable sticky key. They will stay on until you turn them off.

  Please answer back with an update on your status.

  Thank you

  Marilyn
  Microsoft Answers Support Engineer
  Visit our Microsoft answers feedback Forum and let us know what you think