U2414H, button Power LED

Similar Questions

• Satellite A65-S065 - button Power LED is blue & amber at the same time

  1st off I have a S065 A65 and worked well after a replacement motherboard, my fault, he had to be replaced.

  In any case, I have the power button LED is blue & amber LED light up at the same time. Anyone has any idea as to what it means, or maybe I'm going into something, I don't know what it is and it should be reset at the back. Any ideas?

  Thank you
  Ben

  Hello

  I checked the manual of the Satellite A65 and there I can find information that the Power LED blinks orange indicating the machine is in standby mode. So for me it sounds like that your laptop is in sleep mode.

  What happens if you click Start > stop and choose the closing down in the menu drop-down? Normally, the power LED button must be turned off and also the laptop is in sleep mode.

• Z820 - button Power LED blinks 4 times (red) with beep... bad card (Quadro 4000) graphics?

  Hello

  My Z820 at the office is suddenly having a few hardware malfunction.

  When I turn on my machine, the PSU/system fans don't rev and the Power LED button flashes red with a beep 4 times.

  According to this page of troubleshooting, this indicates a faulty PSU on the new UEFI computers:

  HP desktop - computer does not start and emits a LED or a beep Code

  Section "code beep and LED descriptions.

  Get the exact model of LED as the example of "power failure".

  Then, I got a new power supply replacement. I still have the exact same model LED and beeps...

  So, I have drawn deeper and found that when I removed the Quadro 4000 card graphics and then put on my machine, the power button LED is lit in blue (led code ' computer-S0 (normal operation) "") and all the normal spin fans.

  The Quadro card seems to be the culprit...

  Unfortunately, I have no alternative graphic card laying to verify this around, I'm waiting for a replacement of the graphics card (via HP service) to arrive tomorrow.

  Is it possible that the power LED button code (4 times red with beep...) has nothing to do with a bad power supply and that my Quadro is bad?

  Dries

  Dry... that Z820 has been giving you headaches.

  Many fault codes have not changed since the previous workstatons.  I hit this series of beeps of error in the past, and often doesn't mean that the power supply itself is the cause.  It can be a hardware device to the bottom of the chain causing a power surge to power, triggering his "crowbar circuit: fault protection

  http://en.Wikipedia.org/wiki/crowbar _ (circuit)

  Here are the instructions to deal with this series of beeps of a previous HP xw technical and repair.  Note the number 2 in the troubleshooting instructions... usually you don't have to go down to 3, in my experience.  I think that you have already found the faulty unit:

  Loss of power.
  1. open the access panel and make sure that the power cable is properly
  connected to the system board.
  2. Locate the faulty device by removing all devices and then reinstalling one at a time
  until the workstation fails. Replace the device at the origin of the failure. Continue to add
  devices to make sure that everything works correctly.
  3. check the power supply feature.
  a. turn off the AC power.
  b. remove all cables internal power on the system board.
  c. connect the power supply.
  ● If the power supply fan turns and the BIST LED lights, then the
  power supply is good. Replace the motherboard.
  ● If the power supply fan does not turn or the BIST LED does not
  light up, replace the power supply.

• replacement for the power button cable / stop, power LED and HDD LED

  Need to find cables to replace the header 9 pin on the switch / stop, power led and HDD LED indicator.  It is a PC HP Pavilion Media Center m8530f.

  Additional details - no one A High School HE thought that the switch was bad on this PC, so they tried to replace it, but ended up damaging the cables.  The real problem was a power supply dead, so I ordered a new, but now I need to fix this as the person IT damaged the power button, power LED and HARD drive cables.

  Here is a link to your m8530f on HP Part Surfer. I think the part you want is "power switch cable assembly (Black Canyon), part number 5070-2940. It looks like it is available, but you can always call HP and ask.

  Frank

• power led on the rear of the computer the power button / stop turns on, then turns off.

  I have a HP TouchSmart 610-1015xt.  The light on the transformer power is on, but not exactly brilliant (I think it's good, but not sure).  The light next to the power input is on.  When I plug in the power, the power led lights up for a couple / few seconds then turns off and does not turn.  At no time the computer capable of running and it does no whether noise (no fans, no beeps, no attempt to start.

  Any suggestions?

  Figured it out.  Apparently I have reset the battery internal and then unplugged the power button circuit and then he started upward.  The only problem is that now it will restart automatically every time it is closed or even sleep.  I'll start another forum on this issue.

  Thank you for your help.

• Portege R100 stoped working - the power LED flashes error codes

  I have a R100 that has suddenly stopped working.
  The power led (clear amber with the image of the power wire) flashes what appears to be an error code of 5 flashes with a long pause on the last flash, followed by 3 flashes.

  That - what it means, and where can I get a list of all codes error?

  I changed the main battery, changed the spare battery and changed supply - and again, I get the error permanently. I was not able to power the laptop at all since it started. When you press the power button / nothing happens.

  I hope someone on this forum has some information that may help you diagnose this problem. Tech support representatives Toshiba post here?

  Thanks in advance.

  Hello

  I m not a R100 owner but to me it looks like a card mother malfunction because you have already tried to exchange the battery and the AC adapter.

  In this case, the best solution would be if you go to an authorized service provider. Technicians can consult the specifications and they know what means this code I think.
  Here it s only a user to user forum and I have never seen anyone from Toshiba again.

  Anyway, here you can search for the nearest ASP:
  http://EU.computers.Toshiba-Europe.com-online decision-making supported downloads & => find an authorized service provider

  Good luck!

• Satellite L40 - 15G - does not start, only power LED lights

  Hello.

  I have a Satellite L40 - 15G that will not start. I click the power button, or with the battery, and only the power led alternately. I can open and close the cd/dvd, but nothing else works. No beeps when I remove the memory, the hard drive led blinks even. I tried with another hard drive, and it's the same thing.

  Could this be the motherboard, the processor?

  Appreciate the help!

  Hello

  Unfortunately, it looks like a hardware malfunction. I guess that it s related to the motherboard or perhaps CPU, if you have already tried another memory module.

  You should go to an authorized service provider. Guys have good diagnostic tools to check your laptop and repair. In addition, they can order spare parts Toshiba.

  Sorry, but everything that s what I can say. Here he only a user to s forum

• Yellow flash - Satellite Pro 6070 DC power led

  I have a Toshiba laptop that I got from a friend, when I push the power button that flashes a green light as if it's going on, but then the DC power led starts flashing yellow. I have looked this up, but wanted to make sure it was good...

  I thought he had 3 batteries on the cell phone the main bios one and another one. I looked at other newspapers on here and tried to run right next to the power, but the same thing happens.

  How would he fixed or what could be the problem?

  Hello

  It dose not sound very optimistic the domain controller IN the witness lights usually green when DC is supplied from the AC adapter.
  But if the output voltage adapters is abnormal or if power outages, this indicator flashes orange.

  Either there is something wrong with electronic power supply on the motherboard or adapter AC is defective.
  I think it s the first possibility and in this case I n t think you will be able to fix it yourself.
  I'm afraid the technician advice and help is needed: (m

• Qosmio X 500 does not start and the power LED is flashing every 5 seconds

  Hello
  I need help my X 500 does not start now. I tried to launch the NB as usual and suddenly the X 500 start or even power up.

  If I press the power button / stop it makes no noise, the power LED on the button and the second power LED just bliks once and turns on and keep blinking every 5 seconds.

  I tried to:
  * Remove battery and power up with AC only
  * power only to batteries
  * remove the battery power button hold for 30 seconds and over power with AC, battery only athen

  but it did not help.

  I checked the LEDs AC & battery, but they do not blink, they are just RED, so there is no problem in battery or AC.

  No idea where could be the problem?

  Thanks for help
  Frantisek

  Hello

  The failure of RAM could be the reason for this behavior of the laptop.
  Remove the RAM modules with good modules tested and check the functionality of the laptop.
  In the case of RAM isn t the troublemaker, the motherboard could be affected.

  Good luck and share your experience with us.

• the power led stops working...

  in my macbook pro (early 2011) during the update of the el capitan 10.11.2 to 10.11.3 power led to go to Flash mode & stops working after update.can help me! ?

  The usual remedy is to reset the SMC. Read all the steps.

  Before resetting the SMC

  Try each of the following steps in this order before reset you the SMC. Test the issue after execution of each troubleshooting step to determine if the problem persists.

  1. Press Command + Option + escape to force quit all applications that are unresponsive.
  2. Put your Mac to sleep choosing the Apple () menu in the menu bar at the top left and then choosing sleep. After that he went to sleep, to wake up the computer.
  3. Restart your Mac by choosing the Apple () menu in the upper-left menu bar, then selecting restart.
  4. Stop your Mac by choosing the Apple () menu in the bar menu at top left and then choosing stop.

  Resetting the SMC on laptops with a battery you should not remove on your own

  1. Shut down the computer.
  2. Plug the MagSafe power adapter to a power source, connecting to the Mac if it is not already connected.
  3. On the built-in keyboard, press Command-Option-shift keys (left side) and the power at the same time button. Power adapter light can cycler deactivation / activation once.
  4. Release all the keys and the power button at the same time.
  5. Press the power button to turn on the computer.

• Satellite L455 - plug-and - battery LEDs power LED and it flashes orange

  I have a Satellite L455, which worked perfectly for more than six months now, but two weeks ago he began to behave strangely.

  I turned off the machine normally in the evening I was going to sleep. In the morning when I turned on it it turned on, HARD drive and on power LED blinked blue for a few seconds then they are gone. Machine does not start. I tried to turn it on again and it does the same thing. Then I saw the "power plug on" and "battery on" LED flashes orange at the same time. I unplugged the power adapter. Both lights were continuous blinking but machine will not feed. I removed the battery for a piece of 5 minutes, then reinserted it and the machine has worked all day.

  I went he deleted off the power plug and the morning again it wouldn't start until the when I removed the battery for a few minutes then it works again. The battery recharges very well that when I remove and reinsert it even without connecting the power cable still lights up and works perfectly.

  Then, I removed the battery and the power supply Plug and you press the power button for 30 seconds to unload the machine and then return power and battery and it worked until I turned off again and shutting off the power and then it didn't once again.

  If I stop just of machine and do not turn off the power cord, then I can turn it back on to and work with the machine without hassle even for three days without interruption.

  What could be wrong? Any help will be really appreciated.

  Concerning
  Yusuf

  Hi chidzungo,

  It must certainly be a hardware malfunction but he s strange why it pops up every day after you have closed the laptop. Do you use batteries and AC/DC to original Toshiba adapter? Have you connected external devices to your laptop? If so delete them before you turn on your laptop.

  What version of BIOS is installed at the moment? You should look on the Web from Toshiba website for an update. Update of the BIOS might also help and it s worth a try.

  Before you start reading the BIOS BIOS update instructions update [HERE: http://forums.computers.toshiba-europe.com/forums/ann.jspa?annID=60]

  Satellite L455 seems to be an American model, so the BIOS update can be downloaded from the Toshiba U.S. page but first check the exact part number:
  http://www.CSD.Toshiba.com/

• flashing power LED, interrupted Firmwareupdate? N900 WNDR4500

  Hello

  a few hours earlier, the N900 router lost connection to the modem for a few seconds. It happens all the time, so I stop the router and then turn it back on.

  Now the Power LED blinks green all the time. I have red, this could happen if a firmware update is interrupted. Now I don't know what to do. I tried to reset the entire router, but router does not restart after pressing the button reset for 10 seconds (I wait 10 min now).

  It would be nice if you canhelp me

  Best regards

  Nils

  No, I can't ping the router and I can't open the URL 192.168.1.1 / 192.168.0.1

  not even the modem can find the router.

  We use an easybox803a by vodafone as a modem. The thread of this box is really bad, we have the netgearrouter spending range. the N900 is connected to the lan boxes easy port.

• IdeaPad U310 tactile power led flashing

  Hello

  I just noticed that the power led of my touch u310 flickered continuously. The led on the power button also flashes constantly. The flashing happened even after I shut down the computer. The only time wherever the lights flash when I disconnect my ac. Anyone know what could be the cause of the problem?

  Thank you

  It turned out that I disabled the smart update of lenovo and my problem went away.

• HP mini 1109tu does not illuminate and has its power led flashing

  Well I just got my Bill Mini of the day the following day and while they were inspecting it this morning the power led flashes and it won't turn (even on the battery mode).

  [IMG] http://i168.Photobucket.com/albums/u171/Arnaehl/img_96221_hp-1000.jpg [LINE]

  Will or may someone help me solve this. I can't bear to look at my dead minis.

  Thanks in advance.

  HP mini 1109tu

  Hello

  Arnaehl wrote:

  Well I just got my Bill Mini of the day the following day and while they were inspecting it this morning the power led flashes and it won't turn (even on the battery mode).

  [IMG] http://i168.Photobucket.com/albums/u171/Arnaehl/img_96221_hp-1000.jpg [LINE]

  Will or may someone help me solve this. I can't bear to look at my dead minis.

  Thanks in advance.

  Try a hard reset.

  Disconnect the electric plug. Remove the battery.

  Press and hold the power button for 15 seconds.

  release the power button.

  Plug the AC adapter.

  Press the power button.

  Best regards
  ERICO

• Acer Aspire S7-392 lights flashing power led

  Yesterday when I tried turing my S7 on it would not turn. Power led kept flashing. so I plugged it to think of HQ, there lack of battery, but the result was the same.

  After reading some post online I reset the battery, he turned. I quickly took my working backup because it could happen again. And today it turned out I was right.

  I've tried so far things:

  • reset the battery from the back.
  • removing the battery from the inside and with the power for 30 seconds
  • FN + f12. does not not, as soon as the key is pressed, it begins to blinkg
  • read a few post on flashing the bios coundn't find the right way for s7-392 so tried of s7 - 391. bios donwloaded. It extracts. copied to USB. held fn + ESC and then turn it on. did not work as soon as you press power button / stop led continues to Flash

  I tried it didn't work. I decided its time I put it in the trash. The thing has been in and out of the repair shop, over 2 years. I never had cell phone that easily beat without fault of the user.

  Did you know that the first time, I bought this 3 weeks speakers stopped working. After 2 months, every time I turn it on it disk check-up. and all died within 6 months. It was under warranty so he sent to acer repair workshop. He come back every thing worked initially. but in the first enclosure week has stopped working again with 1 usb port. within two years, I've had it already spent enough for a new ultrabook.

  Even though my friends said acer is not a well, the thing seemed so nice, so bought some anyway. I learned my lesson will never buy an acer product.