U2414H questions

Similar Questions

• U2414H - question Daisy chaining

  Trying to get U2414H monitor purchased from Dell daisy chain with MS Surface Pro 3 (8.1) (all updates made). Driver for the monitor is also downloaded and installed.

  Have Surface Pro 3 dock miniDP to DP (en) U2414H then (out) DP / DVI on 3rd screen.

  I activated PD 1.2 on the Dell and I can extend screens of the Surface of the U2414H very well.

  I clicked on "detection" to see if it detects the screen which is attached via DP to DVI cable and it gives ONLY the option to connect via VGA.

  I could go buy a DP to VGA cable and hope that it would work with that, but why the options do not have a choice of DVI? If possible, please let me know what to do to get this choice.

  Thank you

  Katrina

  Update: ordered another monitor U2414H, but none of the cables provided with this worked. I had to order a cable of DP to DP to connect two monitors. DPout used in the RPI and it works fine now.

• U2414H DP 1.2 STD questions

  Hello

  I have exactly the same problem with 3 monitors U2414H.

  P25 User Guide:

  "To allow the connection of STDS, Please use only DP cable such as estimated in the box (or) other DP1.2 certified by cable and change the RFP DP1.2 setting by following the steps below:

  There is no DP > cable DP in the box, only a CDM > DP.

  Cable to connect the DP STD monitor shows the first image can be found in the RFP (NO CDM) of the first monitor.  (Which is the opposite of the connecting cable DisplayPort (Mini-DP DP) black P24)

  The PC is an HP 6300 Pro running an AMD Radeon HD card 7450 DP - it will not detect the monitor as having STD available.

  Do I have to go buy another RFP > RFP cable?

  rod_bunny,
  Our cable should suffice.

  In a monitor three DP MST parameters, only the first and the second monitor in the chain would be DP active 1.2 in the OSD.

  Computer monitor 1
  computer card video DP or CDM on--> monitor 1 DP or CDM in via the Dell mDP to DP cable

  Monitor 1 monitor 2
  Monitor 1 DP 1.2 MST on--> Dell DP to the CDM cable--> Monitor 2 CDM in

  Monitor 2 monitor 3
  Monitor 2 DP 1.2 MST on--> Dell DP to the CDM cable--> Monitor 3 CDM in

  Of course, this assumes that the video card and driver are compatible DP 1.2.

• Power U2414H / Initialize question

  Last week, I bought three monitors Dell U2414H.

  One of them seems to keep restarting.
  NOTE: Only the power connector is connected, so no USB, no HDMI and no DP cable is connected.

  When I turn on the screen sometimes some vertical green lines appear in the contrary case the Blackwatch screen or watch a few dark vertical lines.
  After a few seconds (random), the monitor turns and turns immediately again.

  Sometimes I'll see the backlight just before the monitor goes blank again.

  It is not possible to open the OSD menu and it is not even possible to turn off the monitor (without disconnect).

  NEW: The problem seems even with only a plugged power cable, so I don't really know what is not a problem of software/driver/GPU. It seems to be a hardware/firmware failure.

  When I also connect the USB port, Windows reads the sound "connected equipment" and "disconnected material" and maintains this repetition based on the monitor switch on/off.

  Is this a known problem or can it be fixed?

  mastermattie,

  Not a problem known and not, can not be solved. This monitor should be exchanged. You buy them directly from Dell?

• Dell U2414h menu gone? Keys no longer work?

  My Dell U2414h monitor is connected to the end 2012(El Capitan) Apple Mac Mini HDMI. After 1:30, I can't go back in the Menu of the Dell printer. It seems as if the touch buttons no longer work. It seems that if the menu is somehow locked.

  The only thing dat will work is cut off from the power supply. After that work very good tactile buttons, but after a while or when I closed the Mac Mini, I can't go back in the menu. The Dell monitor is now also waiting because I cannot 'touch' the power button.

  Someone know what I did wrong or is something wrong with the Dell U2414h or is it something in the Apple Mac Mini?

  I asked the same question in the Forum and they said that it might have something to do with my Apple Mac Mini.

  During the Forum, they gave me a solution that does not work for me:

  Reset the U2414H and re - test
  * Turn on the computer and monitor off
  * Disconnect all cables from the screen, including the power cable
  * Press the power monitor in 30 seconds button
  * Plug the monitor cables for the monitor and the video card of the computer. There should be only one cable video connection from the monitor to the video card
  * Turn on the monitor, then the computer

  Note, as this model was not tested/validated on the proprietary Apple hardware, ports, and the software, you must also post on the Apple Forum of Discussions and see if they can offer an overview or troubleshooting steps.

  
  

  Also does not work the solution in the manual to touch the power button for 10 seconds.

  
  

  Someone knows what's the problem?

  I think it is likely yo have a problem with the monitor. The video and does not interact with the onscreen menu/controls.

  -Try to reset memory NVRAM/PRAM and SMC

  MacIntel: Reset of the controller (SMC) system management

  Subject of memory NVRAM and PRAM

• U2414H, Dual, laptop, Windows 10, Nvidia GTX 960 M, no STDS to the second monitor?

  Hi all

  I hope that I have included all relevant information in the present, but ask if I missed something. I bought two of the screens U2414H and a Windows 10 laptop computer powered by GTX 960 M with HDMI and Mini DP ports. My goal was to be able to the Garland of the whole U2414H screens so I could use my laptop out and about, and when connection back to the monitors of would have to plug in a cable and get two screens. In theory, but...

  I followed the instructions and using two Mini-DP to DP cables, connected the mini laptop RFP RFP on the first screen. DP on this same screen highlights Mini DP on the second monitor. I activated the DisplayPort 1.2 on both of these screens. I can't get any signal on the second monitor, it boils down to the power saving mode.

  Otherwise, I decided I would try using two cables and ditch the idea of DP STD I can at least use the two screens. So I have laptop HDMI to a screen and the MiniDP to another, and therefore, that alone will never work at a time. Individually, they work very well, both with HDMI or DP. But the two connection fails every time. When I tried to connect a display of alternative supporting HDMI as the second, which works very well.

  So I had an autour reading and it seems that it is common to have problems of connectivity to these screens. This brings me well on my two questions:

  (1) is there something that would work?

  (2) assuming that there is nothing that works, Dell can swap these screens for two that will achieve what I need?

  Thank you

  Dave

  In MST, DP 1.2 should be turned off (disabled) on the second monitor.

  Laptop AMD on--> U2414H CDM to cable DP--> DP U2414H #1 in (DP 1.2 enabled) (Port #3 in the image)

  
  #1 U2414H (Port #5 in photo) DP--> DP U2414H CDM cable--> 2 # U2414H CDM in (DP 1.2 disabled) (Port #4 in photo)

  When you use only no STDS, is the lid of the laptop open all trying to run two monitors of U2414H? This laptop can even run three screens, laptop LCD + 1 # U2414H + 2 # U2414H?

• U2414H, DP cannot see Bios screen

  I read a lot of posts on the U2414H and the problems with DP. I have a unique question to add. I have two monitors U2414H, NOT chained. The two are connected with full DP DP full of my quadro FX1800 to the monitors themselves. When I turn on my PC, monitors remain in power saving mode until appears the windows login screen. After this point, they work no problem whatsoever. Could be worse, but I can't access the bios at all with these monitors. If I hit the key to the bios, the PC will get into the bios, but my screen is simply stay in energy saving, so I'm stuck until I reboot manually. Has anyone else had this issue or know how to fix? CHANGE > Yes, I did the factory reset in the settings of the monitor. I also tried the solution proposed for monitors of the Garland with registry changes, even if my monitors are not chained. No effect.

  To display the bios, you will need to connect to the FX1800 via its DVI port.

  Computer video card DVI out-->--> U2414H HDMI DVI to HDMI Cable to

• U2414H - problem with DP and DVI dual monitor

  We recently bought 10 monitors x U2414H with 5 machines Dell Precision T1700 each with a Nvidia Quadro K620 x 2 GB graphics card (1 x output DP) and 1 x output DVI.

  When advised on these machines, we were also told to the DVI work with our monitor, we would need special cable conversion so learned the order of 5 x DisplayPort (male) to DVI - D (male) cable. At the time to take delivery of our new machines, it became that there was a problem with the configuration that we had been sold. When you connect the first monitor to the billboards on the graphics card, it works fine. However, the problem is when you plug the 2nd monitor, nothing is displayed when it is connected to the graphics card DVI port.

  We also called Dell technical support and our account manager to try to solve the problem and they suggested using a HDMI DVI-cables rather than the DVI cable to DP that we sold would not work because of the output frequency. After receiving the 5 x new DVI-cables HDMI question still exists and is no different from before. To remove the graphics card or DVI output being at fault we connected to another single monitor using a DVI to DVI cable and it worked.

  Reading through some of the similar positions, it seems that the monitor that we have been delivered is not the good revision number. I've seen a forum member Dell advises that the revision number should be REV A03 while we have been delivered REV A01.

  Any advice on what we should do to solve this problem will be greatly appreciated.

  EDIT: Added required information
  
  * What is the serial number of 20-digit alphanumeric monitor? CN - 03415 X-74261-4AT - 116L
  * What is the revision number (A00, A01, etc.)? A01
  * This specific computer model, portable office/computer? Dell Precision T1700
  * What operating system? Windows 8.1
  * Which video card? NVIDIA Quadro K620 2 GB graphics card
  * Which ports are available for the video card? 1 x DVI 1 x DisplayPort
  * Which video output port are you using video card for video on the port monitor? DVI to HDMI and DisplayPort / Mini DisplayPort
  * What cable are you using to set the video card to the monitor? DVI (male) to HDMI (male) & DisplayPort (male) to HDMI (male)

  If your Dell account manager allows it, go to the AMD over-pants W4100 would be a good step to solve this.

• Black screen U2414H DisplayPort more low setting applied

  I have a dell precision computer M4800 laptop with docking station and two monitors U2414H.

  * Windows7

  * AMD over-pants M5100 FireGL V

  * I use the supplied cables supplied with the monitor miniDisplayPort

  * The docking station has two output ports DP (video 1 and video 2)

  * I've only tried the miniDisplayPort on the monitor inputs

  * The monitor was purchased through Dell

  A monitor works perfectly well, and works with a cable and either output DP (so I guess that the docking station and the cables are fine).

  However, the other monitor shows a black screen (if his hip as a single monitor or if I try to add the two together).

  Windows displays this warning when it is connected:

  Display applied lower setting port

  "The system has detected a problem with the connection between your computer and the DisplayPort monitor that prevents you to use higher resolutions and/or refresh rate."

  The monitor shows a black screen and is configured with a miniDisplayPort as input Source.

  If I try to bring up the OSD message is displayed:

  "There is no signal from your computer. Press any key on the keyboard or move the mouse to wake him up. If there is no display, place the monitor button now to select the correct input in the on-screen Display menu source. »

  I wasn't able to do a reset to the factory via the OSD settings, but I managed to turn on/off the setting of DisplayPort 1.2 (based on immobilized the Menu for 8 seconds). I tried with both enabled and disabled for the same result.

  Thanks for the answer by Chris,

  That moment everything works, I'm a little hesitant to restart in case something goes wrong again, but for now, everything is good.

  In the end, I did the following:

  * Update the BIOS

  * Set up the BIOS to disable switchable graphics (which means AMD card is used)

  * Updated AMD drivers

  * Uninstalled Dell Monitor driver

  * Plugged the monitors of the docking station, and then ran the driver monitor DELL software - it detected two monitors and installed the software.

  * The things still are not 100% with the questionable monitor - but I changed the parameters of DisplayPort 1.2 and its working now. (If I got to the "display settings" OSD display display Port 1.2 > disable).

  I put the laptop to sleep all night and he works up and all the monitors turned on (yay), but I am yet to perform a reboot since I have things to work.

  I'll close this issue even if things work out right now. Thanks for the suggestions (such as various tests I did based on your suggestions led me through the steps above to make it work).

• U2414H randomly turning power on and off

  Hello

  I bought my U2414H (Rev.) A00) in March 2014 and after a few days he began to morph randomly, sometimes for a few hours. Sometimes days would pass without it switched off voltage, but most of the time the screen turns off during the night, while in stand by. I know that it is a common problem with the U2414H and I want to know if Dell has found a solution to this problem other than the monitor. I love the photo of this unit and I would not return, especially knowing that I get a refurbished.

  Thank you!

  I can't speak for the other actions of countries. I know that in the USA, all stock A01 (cut into date 18/03/2014) should be fixed for that matter. You will need to contact Dell Customer Service to your country to organize an exchange of monitor. Provide the following data =.
  E-mail address:
  Name:
  Shipping address:
  Phone number:
  Monitor order number:
  Monitor 20 serial alphanumeric digits:
  Problem: Hardware failure causes a power/Black screen/switching off questions
  Policy: A new scholarship will be issued for users still inside the first 30 days following the date of the invoice. An Exchange used/refurbished will be issued for users outside the first 30 days of the invoice date

• iOS 10 people record problem/question

  Hello

  I have a couple of "faces" in the issue of people who are coming in white, but acknowledged same 'face' of many times.  Is anyway to update it for photo comes actually?  At a few faces, I don't know that facial recognition found since it is coming from white.

  Hi JohnP007,

  Congratulations on your iPhone 7 more running iOS 10! I understand that some of your faces in the album of people pull up as a draft and you want to refresh. You can try to use the steps below to fix the faces on the thumbnails in albums.
  

  Difficulty faces and names mixed-up

  If you notice that there is a photo of someone in a collection that is poorly identified, you can remove it.

  1. Tap the person you want to remove in the album of people > select.
  2. Type Show done face to emphasize his face in every photo.
  3. Press on each photo that is not the person.
  4. Type > not this person.

  Hide people

  You can hide the people or groups that you don't want in your album of people.

  1. Open the album people and press Select.
  2. Touch the people you don't want to see.
  3. Click Hide.

  If you want to see the people that you have hidden, press on show hidden people.

  People in the Photos on your iPhone, iPad or iPod touch

  This should be corrected without delay faces. Please use the Apple Support communities to post your question. Good day.

• Questions - and answers forgotten

  How to get my 'secret' answers to the questions that I have noted the way back when?

  If you forgot the answers to your questions of security of Apple ID - Apple Support

• I can't reset the security questions. We received notice as below:

  Hello world

  I can't reset the security questions. We received notice as below:

  "Cannot reset Security Questions."

  We have insufficient information to reset your security questions. "

  Please help me as soon as possible! Thank you very much.

  Hello

  You will need to contact the Apple Support.

  The information is available here:

  Contact Apple for assistance with the security of the Apple ID - Apple Support accounts

  (I'm afraid that no one here can solve the problem for you - this is a user-based community).

• Question of cloning for SSD upgrade on 12 Macbook Pro

  Previously, I did an upgrade to SSD on my Macbook Air to 2012 according to the instructions of JetDrive transcend. Basically connection via USB 3 and using Mac OS X to clear (and format) disc utilities new SSD, then restore again SSD and then remove the original 128 GB SSD and insert the new 480 GB SSD.  For about a month and so far without problem.

  Now I'm trying to 2012 Macbook upgrade my Pro partner (on 10.11.6).  I got a Crucial SSD MX300 to replace his HARD drive.  Crucial comes with (or recommend) Acronis software.  And a lot of the messages of the forum recommend Carbon Copy Clone.

  My question is if I can use the same method for the cloning of the HD as my Macbook Air (just restore disk of Mac OS X utilities)?  This time, I'm upgrading HARD drive and I don't know if something is different.  At the same time, if I got lucky the first time, I don't not ruin Macbook Pro my spouse this time.

  Thank you.

  Yes, you can use disk utility to clone your MBP wives, but unlike CCC, it will not clone the recovery and Partition.

• Question about resolution movie downloads

  If I buy a movie at a certain resolution (780p for example), but I want more later re - download at a higher or lower resolution (SD or 1080 p), can I do so and how?

  Same question perhaps for music. Some of my songs have been bought before the latest Apple codecs.

  Any help is appreciated!

  THX!

  Once you have made a purchase on the iTunes store, you will see your purchased items in the menu under accounts bar > bought. You can simply select the item purchased and re-upload.

  With regard to the resolution of the film for films that are offered, and you select the resolution, you can download it again and select a different resolution. For movies that are available as separate download to SD, 780, or 1080 points, you would be limited to the original resolution you selected.