U2715H, the issue of consistency & backlight bleeding
I just got my U2715H two days ago and I noticed the color of the screen backlight is not uniform (on the left side has a pink tint and brightness levels vary up and down). I also bleed backlight. I find it
unacceptable when paying $650 for a monitor during my previous $150 we not had one of these questions. Please tell me that there is a defect.
Check your message private to me.
Tags: Dell Peripherals
Similar Questions
-
Unacceptable backlight bleed with Dell U2414H - credit refused to Dell or upgrade
5 days ago bought 2 monitors a U2414H Dell and DELL UP2516D in Hong Kong.
The Dell U2414H a lot of backlight bleeding, the worst thing is the ugly yellow glow really distinct on the upper left, visible even in office lighting. The backlight bleeding was acceptable limit if this not that hideous yellow glow in the corner of a whole new monitor.
The DELL UP2516D, I have not had any problems with it at all.
Dell sent support some pictures and asked for credit/upgrade to the DELL UP2516D, but was denied a response:
"We verify that this is a normal matter. Because it's the technique of back-lighting, all the monitor will be this phenomenon. It is not hardware issue, so we can't support you for the UP2516D upgrade or the refund. »
I had a lot of monitor in my life, it's not normal or acceptable.
Help, please
It's the Forum USA, so you will need to re - contact Customer Support for your country. That U2414H does not meet our specifications from manufacturer of uniformity of the backlight. They do not follow the Dell return policy. Inside of 30 days of the invoice date, you can get a refund for ANY reason any. Don't like us for like exchanges, so that they are correct in saying you can't return the U2414H and get the UP2516D.
-
How is it assistant BootCamp 6.0.1 running on El Capitan 10.11.5 installs single partition BootCamp on the disc Fusion consisting of 128 SSD part G SSD and 3 TB of HARD drive on an iMac (retina 5K, 27 inches, end of 2014), but not the part of the HARD drive?
This has two questions:
1 capacity of SSDS faster for Fusion drive has been reduced. Therefore less effective for the reader of the merger. For example if I need to create a partition of 80G for my windows bootcamp partition, only 48 G will be left in the drive of the merger.
2. ability of the bootcamp windows partition becomes very limited, cannot be greater than 120 G.
3. even when I try to fuse out of the drive of fusion in the 128 G SSD and 3 TB of HARD disk, and then run the BootCamp assistant to create the bootcamp partition start from scratch to reinstall El Capitan only on the HARD drive (without drive Fusion), it won't let me do anything, it just shows an error that says something like "a person has created additional partitions on this drive please select. another disc. But there is nothing else to choose.
Before my (5 K, 27 inches, end of 2014 retina) to El Capitan Yosemite, I was able to use the previous version of the wizard BootCamp 5.x to create the partition, bootcamp on the drive of the merger. And it will be divided in the fuser unit in two and insert the Bootcamp partition (with the size I chose, which can go up to 1 TB) between two partitions of MAC OSX.
The disk partitions resulting from it, will be the partition MAC OS x on the SSD, the partition MAC OS x on the HARD drive partition #1, partition MAC OS x on the HARD drive partition #3.
Then there is the BootCamp partition on the HARD drive partition #2.
Is there a way to get what I need?
That is what has been described in this notice of two canoes?
Installation of Windows on a Boot Camp partition on a drive of TB Fusion 3
Thank you.
After having worked on those weeks, I realized that I need very painfully (by first going back to Yosemite and bootcamp 5 to escape all the limitations of El Capitan and BootCamp 6) I want to share here. Someone at - it other smarter solutions welcome.
Note these steps and mentioned drivers only work for my version of iMAC, retina 5K late 2014. If you have other material, please search on the web to see which driver will work first. And all of these steps are destructive and assumed that you first take backup. It is only shared for interest only. Readers will have to bear your own risk.
A. take backup
1. take a backup completes my iMac Fusion Drive using Time Machine. Then restart with a Yosemite USB installation and select Terminal from the menu on the top bar.
B. fuse out of the merger in two physical disks drive: SSD + HDD
1. in the terminal, type the commands in show what the logical volume group ID and the ID of the logical Volume of the disc fusion)
Cs diskutil list
2. in the terminal, type commands for the fuse of the fuser unit and separate them to an SSD and a HARD drive. Note: All data will be destroyed in the drive of the merger. There are many articles in this community on how this could be done,
diskutil cs deleteVolume Logical Volume ID
CS diskutil remove logical Volume Group ID
This should finish within 30 minutes. If you have taken more time, this means that your reader of fusion has been altered somehow.
I hit this issue too. To use this command to remove the fusion drive hung up, and I need to do the hard to scramble a few sections of data in the hard disk partition table using the controls to tell the OSX this hard drive is a new without partitions:
Cat >/dev/random /dev/disk0 (where/dev/disk0 is the SSD)
and repeat for disk1/dev/disk1 which is the HARD drive in my case).
This command will not return anything, but expect to press Ctrl-Z to end after 1 minute.
2 create independent partitions (non-fusionend) for the installation of OSX.
Borne Terminal output, and select disk utility, in disk utility, select the drive to HARD disk (and not on the partition), you will see the error message and you will be asked if you want to fix the fuser unit, click on ignore. Then wipe the HARD drive to create a single 'extended OSX journaled"named"HARD drive".
3. Repeat step 2, and then erase the SSD drive to create a single 'extended OSX journaled"named"SSD ".
C. install on the HARD disk as drive didier autonomous not fusion.
1. go to Yosemite install screen and proceed with the installation of a clean copy of Yosemite to the iMAC. then connect you.
D. use BootCamp Yosemite f5 to install windows.
1. launch Yosemite bootcamp.
2. check the two checkboxes for creating the USB drive to install windows 7 or a later version, and to download the windows supports the Apple software. Do not click on the last box to install or remove windows pie creating real bootcamp partition again.
3. it may take several hours to complete this function of your internet b/w and also performance of your USB drive.
4. If you install Windows 7 (like me), then the downloaded drivers will not work for you, this will cause the issue of the device driver appleDSS.sys does not like this driver and others are too recent for windows 7 to use. Also, your keyboard and mouse may not work even if you try to plug in a USB external keyboard or a mouse. You need to replace the drivers downloaded by others (the Boot Camp 5.1.5769 drivers that I find in this link: Software Support of Boot Camp 5.1.5769.) (Note: this driver is material specific only works for my iMAC model). Once you have downloaded it, copy the two files in the root directory of the USB installation to replace the original ones. It's specific and material available for download somewhere on the Apple Site.
-From the Finder, delete the $WinPE$ and the Boot Camp of the FLASH PLAYER files.
-Expand the old drivers for Boot Camp 5.1.5769 (two records and another file) on your desktop.
-Copy the $WinPE$ and records of Boot Camp in the FLASH PLAYER.
5. open Boot Camp Assistant again and only select the third option, install Windows 7.
It will show you the screen to select what installation disk, select HARD drive.
Then drag the slide bar to select the size of the Bootcamp partition for windows you want, knowing that there is a restriction for windows installed using training camp on a MAC that the last byte of the BootCamp partition must reside in the first byte of the 2.2 T of each physical hard drive.
For my case, I need only 500G for bootcamp and leaving behind 1.7 to for my MAC OSX partition immediately after the bootcamp partition and an another 0.8 T MAC OSX partition after him. 1.7 TB and the partition of MAC OS x 0.8 TB well exploited in the meantime bootcamp partition, will be merged into a fusion drive by Bootcamp. Thus, you will end up with total 2.5 TB of disk space in a logical drive - fuser.
Go to this link for more details on this subject: n-on-a-3-tb-fusion-drive http://twocanoes.com/winclone/support/installing-windows-on-a-boot-camp-partitio
6. continue the process to partition the hard drive, then it will restart automatically in windows installation mode, install windows.
7. once the installation is complete, check that windows is functioning correctly.
E. Si you want to upgrade to windows 10 Windows 7.
1 if you plan to upgrade to windows 10, you'll find that the windows IE v.8 7 is no longer works and had many problems to load the page. Then when you try to download the latest version of Internet Explorer, you get an error that you need at least windows 7 SP1 to support the last IE. Life is too complicated, just download the google Chrome browser, then search for download windows 10 and then run the Microsoft valuation tool to upgrade.
2 but before upgrade you, unplug all your MAC USB drives, otherwise, you will find that, after having spent an hour downloading the windows 10 software, the upgrade will fail with the error "/ dynamicupdate...» ». It is an inexplicable mistake that no one seems to understand why. There are articles with proven results that the removal of all USB drives before running the windows 10 upgrade tool will correct this problem.
F. reinstall OSX El Capitan
Once your target windows system (if windows 7, windows 8 or windows 10) works very well. You can continue to create again your Fusion drive and reinstall OSX El Capitan.
1. Insert the install of OSX Yosemite rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.
2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.
3. on the selection screen, select start Yosemite OSX install drive.
4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.
5. in the terminal, type the command 'diskutil list cs' and you should see nothing to prove that there are no existing fusion drive yet.
6 type the 'diskutil list' command to list all disks and partitions.
The SSD has two partitions, the/dev/disk0s1 of EFI (209 MB) partition and the other/dev/disk0s2 of OSX partition we created in step B above, called SSD around 121 G.
The HARD drive has two partitions, the/dev/disk1s1 of EFI (209 MB) partition and the other/dev/disk1s2 of OSX partition we created in step B above, called SSD.
G. delete the logical storage of nucleus on the HARD disk drive and it refuses with the DSS to form a merger with faster performance disc
1. Insert the install of OSX El Capitan rear USB to the iMAC, and then select Restart Windows, or stop, and then turn the MAC once again.
2. When you hear the ringing tone, press on and hold down the option key for 10 seconds. Then you release.
3. on the selection screen, select start Yosemite OSX install drive.
4. after starting, do not proceed to install OSX El Capitan again. But select Terminal from the menu bar.
5. in the terminal, type orders for (to show what are the logical volume group ID and the ID of the logical Volume of the logical drive). You should see the logical volume to basic storage group created using two partitions on the hard drive, 1.7 TB and TB 0.8 created when we run the Yosemite Bootcamp to install windows.
Cs diskutil list
6. in the terminal, type commands to delete logical drives from basic storage. Note: All data will be destroyed in the logical drive.
diskutil cs deleteVolume Logical Volume ID
CS diskutil remove logical Volume Group ID
7. tap "diskutil list" command lists all the resulting partitions. You should see that the HARD drive has the following partitions.
/ dev/disk0 (internal, physical):
#: NAME SIZE TYPE IDENTIFIER
0: GUID_partition_scheme * GB 121,3 disk0
1: disk0s1 EFI EFI 209.7 MB
2: Apple_HFS GB SSD 121.0 disk0s2
/ dev/disk1 (internal, physical):
#: NAME SIZE TYPE IDENTIFIER
0: GUID_partition_scheme * 3.0 to disk1
1: EFI EFI 209.7 MB disk1s1
2: Apple_HFS 1.7 Untitled TB disk1s2
3: disk1s3 Apple_Boot Recovery 650.0 MB HD
4: Microsoft database BOOTCAMP 503.0 GB disk1s4
5: Apple_HFS 801,4 Untitled GB disk1s5
8 type the following commands to create the logical volumes group, named "myLVG" (or the name) of fuser using the usable for OSX to the SSD and HDD partitions.
diskutil cs to create "myLVG" disk0s2 disk1s2 disk1s5
Note: Mark the group id of logical volume shown in the results.
In my case, I want to book the last partition as standalone partition disk1s5 no-fusionend, so I can use it to raise the back, or format it in FAT32 to allow the exchange of data between the MAC and boot camp.
So, I do not understand this last partition in the drive of the merger. in my case, the command that I used is: diskutil cs to create "myLVG" disk0s2 disk1s2
9 create logical volumes named "Macintosh HD" (or you call it) on the logical volume group we just created for the reader of the merger.
diskutil createvolume logical volume group ID jhfs cs + 'Macintosh HD' 100%
10 command "diskutil cs type list" to check the resulting fusion drive created.
CoreStorage groups of logical volumes (1 found)
|
+ Logical Volume - Group F53C7A25-C2F3-4997-91E9-2E6B6BAB2E0E
=========================================================
Name: LVG
Status: online
Dimensions: 1815635525632 B (1.8 to)
Free space: 90112 B (90.1 KB)
|
+-Physical volume E176873C-7C80-4759-8110-BA7307E0C4B3
| ----------------------------------------------------
| Index: 0
| Disc: disk0s2
| Status: online
| Dimensions: 120988852224 B (121.0 GB)
|
+-Physical volume 6535AC3C-DCF8-453F-AD47-98905538386E
| ----------------------------------------------------
| Index: 1
| Disc: disk1s2
| Status: online
| Dimensions: 1694646673408 B (1.7 to)
|
+--> Logical volume family F3D15F87-FB84-4B43-B2F2-E9EACC7C42D9
----------------------------------------------------------
Encryption type: no
|
+--> Logical volume 0D807F6E-FB7C-418F-AAF4-EF3EA3525D10
---------------------------------------------------
Disc: disk2
Status: online
Size (Total): 1809780178944 B (1.8 to)
Reversible: no
Name: Macintosh HD
Volume name: Macintosh HD
Content indicator: Apple_HFS
LVG Type: Fusion, sparse
11 exit the terminal, go back to OSX El Capitan install screen and select the name of the fuser unit 'Macintosh HD' proceed to begin the installation of the os x for installation.
12. There will be a step in the installation ask you if you want to configure as a new computer, or restore from a time machine previous backup. Make your own choices it accordingly.
13 once OSX El Capitan has been installed and you have finished restoring the data and custom configurations, you can enter the application of preferences to check if you see the icon of the "Startup" disk", and if you choose Startup BootCamp in the next reboot, you should be able to boot up to Windows without pressing and holding the button option when reboot and choose to start windows manually. Also, in windows, you should be able to click on the bootcamp Control Panel and select for a startup to OSX on the next reboot.
14. one thing to be aware, if you install bootcamp in this way, the boot camp and the GUI utility disk in OSX El Capitan will not be able to adjust your settings. This means, if you need to touch anything or to readjust the size of the partition, you will need to do it again in step A. Alternatively, some how to get started with installing Mac OSX Yosemite USB, then adjust the partitions using similar commands shown in this article or other articles in this community.
15. yet once please take personal responsibility on damage if you follow the instructions in this article.
-
Warranty does cover backlight bleeding on Satellite A300-1JH
Hello.
I would like to know if backlight bleeding to a laptop (it of bad enough, nearly half of the screen is gray instead of black) can be solved with warranty. They change the display or give me a new model? Or are they taking action at all?
I can always return the laptop that 10 days have not passed since I bought it, but I want to keep it if they can change the display. In it's current condition, it is unusable on a long term.
First, you will need to contact the ASP in your country and the ASP technician must check the display / laptop if there is really a bad screen work.
But listen mate...
I read in other forums on the display of the symptoms that you describe in your ad and something like which is also visible on LCD TV s and to be honest, it s not a malfunction. They are simply properties of LCD.However, you can contact the ASP and the technician could provide more details on this symptom
Good bye
-
Hey all,.
I had a post a few months ago, but it has been mixed around and did not answer, probably because the edge was still new and was not yet listed on the Lenovo site.
Anyway, I'm having a problem of backlight villain, and I wonder if it's worth to send it to repair. I have attached an image, and you'll notice in the upper left, and about 2/3 left in the upper right there is a fairly large yellow glow. Is this normal?
Thanks in advance for answers!
Needs, no. Expected, Yes.
This is an excellent example of some horrible backlight bleed.
-
Horrible corner of 27XI HP Pavilion backlight bleeding / glow.
I bought this screen 3 days ago and I noticed that there was some really bad backlight bleeding in each of the 4 corners and especially in the lower left corner. This is very visible on dark backgrounds, even on the lowest brightness. Black on this monitor is totally uneven and is horrible.
The monitor is defective? I took a picture of him.
http://S14.postimg.org/4ugapqqw0/20141013_191756.jpg
Moreover, I can always take back at the store, but I would avoid rather than. If it was defective, HP sends a new and takes one here directly or I have to this package and return it by myself and wait for a new?
Thank you.
If anyone cares, I got the replacement and it seems to be a newer version cheaply built the revision of this monitor. It has a different menu of software packages to search with different parameters in it (she has a "certified technicolor" defining which resembles nothing good) and comes with a CD of different drivers. The screen itself also seems to have a different lcd panel drab colors, less 'clarity' and even worse backlight bleeding than the old.
I do not recommend this monitor, not to mention, if you buy it you will get the new revision which has not only bleeding but a worse sign as well. I'll keep my old one and sending it back.
To find out if you have the 'good' version of this monitor or bad, just look at the Setup menu, bad angles rounded and HP brand on top, the 'right' has a completely anonymous menu with square edges. Version of the firmware on the right said RIM111 and bad RIM232.
I am very disappointed with this product, I generally don't like too much about that kind of stuff, but this one deserves a negative review.
-
0x8004fe21 - "this computer is not running Windows" - KB3024777 update does not resolve the issue
Hello
My Windows 7 has been giving me some problems lately. I get messages that "this computer is not running genuine Windows" (0x8004fe21). I'm running a genuine version of windows, and when I check the properties of my computer, it tells my that I have in fact validated my copy of Windows 7.
I also had a problem when new updates to Windows Update settle not and after a few google searches, I have concluded that this must have been caused by bad KB3004394 update.
It has been suggested that I deleted this update, but it did not show anywhere under installed updates.
It has also been suggested that I downloaded the patch of "quick fix" KB3024777, which is supposed to remove the faulty update.
I did, and since then, the issue of windows updates has been resolved. Again installing the updates of windows, but I still get messages I'm not authentic Windows.In addition, I tried all sorts of things, I found in online forums, but I don't remember exactly what those who were, because most of them were things that I didn't understand.
Maybe you guys can help. Thank you in advance!
I was told to run MGDiag and post the results here so here go us:
Diagnostic report (1.9.0027.0):
-----------------------------------------
Validation of Windows data-->Validation code: 0
Code of Validation caching online: 0x0
Windows product key: *-* - QCPVQ - KHRB8-RMV82
Windows product key hash: + Rj3N34NLM2JqoBO/OzgzTZXgbY =
Windows product ID: 00359-OEM-8992687-00095
Windows product ID type: 2
Windows license Type: OEM SLP
The Windows OS version: 6.1.7601.2.00010300.1.0.003
ID: {DFF68C19-1503-487E-A692-8C435EF12F1F} (1)
Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/a, hr = 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Product name: Windows 7 Home Premium
Architecture: 0 x 00000009
Build lab: 7601.win7sp1_gdr.150316 - 1654
TTS error:
Validation of diagnosis:
Resolution state: n/aGiven Vista WgaER-->
ThreatID (s): n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002Windows XP Notifications data-->
Cached result: n/a, hr = 0 x 80070002
File: No.
Version: N/a, hr = 0 x 80070002
WgaTray.exe signed by: n/a, hr = 0 x 80070002
WgaLogon.dll signed by: n/a, hr = 0 x 80070002OGA Notifications data-->
Cached result: n/a, hr = 0 x 80070002
Version: N/a, hr = 0 x 80070002
OGAExec.exe signed by: n/a, hr = 0 x 80070002
OGAAddin.dll signed by: n/a, hr = 0 x 80070002OGA data-->
Office status: 109 n/a
OGA Version: N/a, 0 x 80070002
Signed by: n/a, hr = 0 x 80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3Data browser-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default browser: C:\Program Files (x86)\Google\Chrome\Application\chrome.exe
Download signed ActiveX controls: fast
Download unsigned ActiveX controls: disabled
Run ActiveX controls and plug-ins: allowed
Initialize and script ActiveX controls not marked as safe: disabled
Allow the Internet Explorer Webbrowser control scripts: disabled
Active scripting: allowed
Recognized ActiveX controls safe for scripting: allowedAnalysis of file data-->
Other data-->
Office details:{DFF68C19-1503-487E-A692-8C435EF12F1F} 1.9.0027.0 6.1.7601.2.00010300.1.0.003 x 64 *-*-*-*-RMV82 00359-OEM-8992687-00095 2 S-1-5-21-3113075717-3854388810-3852344427 Dell Inc.. L421X XPS Dell Inc.. A14 11A80F00018400FE 0413 0409 Malay Peninsula Standard Time(GMT+08:00) 0 3 DELL CL09 109 Content Spsys.log: 0 x 80070002
License data-->
The software licensing service version: 6.1.7601.17514Name: Windows 7 HomePremium edition
Description: operating system Windows - Windows (r) 7, channel OEM_SLP
Activation ID: d2c04e90-c3dd-4260-b0f3-f845f5d27d64
ID of the application: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 00359-00178-926-800095-02-1043-7601.0000-1052015
Installation ID: 019613804902779735492485549691725206407303392291262906
Processor certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
The machine certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
Use license URL: http://go.microsoft.com/fwlink/?LinkID=88341
Product key certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
Partial product key: RMV82
License status: licensed
Remaining Windows rearm count: 2
Trust time: 19/04/2015-16:10:57Windows Activation Technologies-->
HrOffline: 0x00000000
HrOnline: 0x00000000
Beyond: 0 x 0000000000000000
Event timestamp: 4:15:2015 22:03
ActiveX: Registered, Version: 7.1.7600.16395
The admin service: recorded, Version: 7.1.7600.16395
Output beyond bitmask:--> HWID data
Current Hash HWID: LgAAAAAAAQABAAIAAAABAAAAAwABAAEAln3yCEagjqxGq8ILYPbwHZ5vvtyWYw ==Activation 1.0 data OEM-->
N/AActivation 2.0 data OEM-->
BIOS valid for OA 2.0: Yes
Windows marker version: 0 x 20001
OEMID and OEMTableID consistent: Yes
BIOS information:
ACPI Table name OEMID value OEMTableID value
CL09 DELL APIC
CL09 DELL FACP
DBGP DELL CL09
HPET DELL CL09
STARTING DELL CL09
CL09 MCFG DELL
TCPA DELL CL09
CL09 DELL SLIC
CL09 DELL UEFI
ASF! REFERENCE DELL CL09
CL09 DELL SLIC
SSDT CRV COMPAL ORB
ASPT DELL CL09
FPDT DELL CL09
SSDT CRV COMPAL ORB
SSDT CRV COMPAL ORB
LAURENCE DELL CL09
SSDT CRV COMPAL ORB
SSDT CRV COMPAL ORBI don't see anything abnormal in your report - which probably means that the problem is a race condition where your AV is to win the fight for access to certain critical files when the Service for the Protection of software needs to access.
Certainly, it will disappear after a few days.
-
Hello
Ive got myself one of these 'affordable' ultra wide gems. They have really beautiful colors, sharpness, usability etc. But until you have something really dark night on them = C.
Short background: Ive branch a week ago and found out that after the warm-up (say 2 hours), boring backlight bleed appears down right next to the buttons. Ive called Dell Support me am replacement, they mail send again and the next DAY same courier picks up an old.
Left monitor is NEW REPLACEMENT, everything is 'old', I bought the week.
http://postimg.org/Gallery/dpxp93e/91f1a32f/
Apartment minor backlight bleed all around them (Yes, technology), they both weird 'feature' of the purge of backlight next to the buttons (bottom right), which will appear after good warm-up! And left a (replacement) is slightly visible even in Office work as dark-VisualStudio etc.
To comment on my pictures, it's difficult to take realistic pictures, IPS glow really take in the way here, I tried my best with the Nokia N8. However you will see in the movies dark night. Two low bleeding are caused by the bottom edge, in my humble OPINION preasuring show slightly inward. It spoils a bit otherwise nice monitors. And Yes both having beside yeach other even for a night makes you immunne against doubt if you chose a "too large", its awesome.
So my question is what do you think? I'm whiney?TLDR: Left a replacement, right 'old of the week' a. What do you think?
Edit: link
g0r4k,
We do not test/measure our monitors in a dark room. We use standard office lighting. But, according to photos, it is within our specifications from manufacturer for difference in backlight.
-
Backlight bleed U2713HM / yellowish lower left corner
First of all I have not directly buy from dell so I do not know how this effects returns. I received my monitor in the last week. I bleed backlight on my monitor which can be seen in the images of gray / black. It is noted throughout the day. I also cover quite visible cross on white / light gray backgrounds but my bad camera would not be able to show that if I didn't try. I'll add some pictures, but I don't have a camera very good with me, only my phone so it's difficult to take pictures, but I tried. Please ignore the white dots, as this seems to be something to do with my camera :/ All with contrast 70. brightness of 100. I have a revision A01 manufactured in April 2013. Thanks for any advice or help,
Rob.
brightness 50
Dark - light 100
Brightness of 50 black
EDIT:
Photo requested to the factory default.
Rob-cook,
You must set the contrast to 75 and the brightness to 75 which are the default values. Dell monitors have no specification 100% backlight uniformity. If this is unacceptable to you, contact the seller and return it for credit. We can not you credit since you do not buy from us.
-
I can't reach some websites with any browser. I get the message ERR_CONNECTION_REFUSED. If I boot in safe mode I don't have the issue. I tried the reset and repair of everything. Help, please
Try to run this program in your usual account, then copy and paste the result in a response. The program was created by Etresoft, a regular contributor. Use please copy and paste the screenshots can be difficult to read. On the screen with the Options, please open Options and tick the boxes in the bottom 2 before the race. Click on the button "Report share" in the toolbar, select "Copy to Clipboard" and then paste into a response. This will show what is running on your computer. No personal information is shown.
-
I just posted a question on the last update automatic 38.3.0 it is possible to log into different e-mail accounts in a profile, only the first e-mail account. My support mozilla account is linked to one of the email accounts that I can NOT connect to. Can't connect to this email account to check the issue. Your last 38.3.0 Thunderbird is useless because it is no longer possible to log in different e-mail accounts in a profile, and your support solution is useless because you need to connect to the e-mail account to check the issue.
How to proceed?You can change your email associated with your media profile.
I have 38.3.0 and I can access all my email accounts I suggest you try the initial tests:Start T-bird with disabled modules.
If it works on your module is to blame and you need to activate one by one.Start your operating system in safe mode with active network.
If it works probably your antivirus is blocking or delaying. (Or driver). -
Pages - trying to link the issue to the paragraph of the answer
Hi there: neophyte user Pages for businesses trying to link the issue of the survey to a paragraph "answering machine". As an example...
Question:
What's your brown grass? Yes No
If the answer is Yes, then want to fill and print a paragraph explaining...
Your grass is Brown, because you're not watering or you need phosphorus or whatever. Here's what you need to know about this resolution. etc, etc.
Any suggestions on the Pages or other popular apps.
V5.6.2 pages is not suitable for the use of processing of affairs where one expects it to be a clone of Microsoft Word - who is not. There is no content link intra-document, support forms or runtime macros that manipulate the content of the document when the interactive user input. Pages is not a web design tool.
-
Since 10.11 I have not been able to download via the usb port of my Davis Vantage weather station. No solution of tech Davis on the issue even with the new recorder of events in the resort. Is there a problem with the usb?
What Mac? (details)
-
Remember - this is a public forum so never post private information such as numbers of mail or telephone!
CODE 66 has when the update NET FRAMEWORK 4 with WINDOWS UPDATE can't update more far until the issue is resolved. Help, please... I almost tried everything. Ideas:
- You have problems with programs
- Error messages
- Recent changes to your computer
- What you have already tried to solve the problem
Take a look at this link and see if it helps-
http://social.answers.Microsoft.com/forums/en-us/vistawu/thread/3adefda0-69f3-4075-96ee-e2c61bd599cc>
-
Monitor the issue after Windows update
I installed the Windows updates today, and after installing and restarting, the saturation of the color on my monitor is out of line. There is intense color saturation and it made all my files photo as well.
Running windows 7 and a HP w2338h monitor.
Thanks for any help on this
fifthboss,
You should look through the updates installed to see if there was an update to the video card. I would then check with the manufacturer of your video card for the latest driver. If you just updated to the most recent and feel it affected the color then you can restore the previous driver. Then you can contact the manufacturer of the video card on the driver and they know the issue and see if they are still aware and have a fix. Mike - Engineer Support Microsoft Answers
Visit our Microsoft answers feedback Forum and let us know what you think.
Maybe you are looking for
-
I have already filled in 3 forms for this more how do need it all the information I can be found
-
Original title: Running Win7 on Bootcamp. Error: The game could not create the Direct3d device. Please make sure your video drivers are installed properly. I try to play Psychonauts out of steam. I am currently running Windows 7 via Bootcamp on my Ma
-
P6 - 2317c: screen stays black
I created this problem myself and I am now trying to fix. It all started with the Player DVD does not. Reading on several different patches, try most with no results, I came across one that tells you to delete the two registry keys, which is the uppe
-
Find the Outlook Express messages to export to new PC
When I try to export my messages and OE6 files, I get an error message. It is said: "the export could not be performed. An error occurred during initialization of MAPI. "What do I do? Thank you John (Cincinnati)
-
Hi how to upgrade flash bios? It is safe? I already download the lenovo driver page. I don't have the dvd drivers BTW is g460