UC500 and IPsec VPN client - disconnects
Just throw a question out there.
I have a UC560 running uc500-advipservicesk9 - mz.151 - 2.T2 site HQ. Remote users, about 8 of them, attempt to connect via IPsec VPN (v5.0.07.0440) HQ clients to access files, etc.. The behavior I see is 5 users to connect successfully, but only 5. As soon as more users trying to connect, they have either:
- connect with success for a minutes, then unmold
- get a 412, remote peer is not responding
- connect, but someone of another session kickoff.
Users use the same VPN profile, but with names of single user and passwords.
Here are some of the CPU configs for VPN clients
Configuration group customer crypto isakmp USER01
key *.
DNS 192.168.0.110
pool USER01_POOL
ACL USER01_ACL
local RAUTHEN AAA authentication login
permission of AAA local RAUTHOR network authenticated by FIS
Crypto isakmp USER01_PROF profile
match of group identity USER01
list of authentication of client RAUTHEN
RAUTHOR of ISAKMP authorization list.
client configuration address respond
crypto ISAKMP policy 1
BA 3des
md5 hash
preshared authentication
Group 2
crypto ISAKMP policy 10
BA aes
preshared authentication
Group 2
lifetime 28800
crypto ISAKMP policy 100
BA aes
preshared authentication
Group 2
life 3600
crypto ISAKMP policy 1000
BA 3des
preshared authentication
Group 2
I enabled debugging
Debug crypto ISAKMP
Debug crypto ipsec
Here are some of the things that I see on him debugs
604899: 16:41:13.333 Aug 21: ISAKMP: (2073): HASH payload processing. Message ID = 284724149
604900: 16:41:13.333 Aug 21: ISAKMP: (2073): treatment protocol NOTIFY DPD/R_U_THERE 1
0, message ID SPI = 284724149, a = 0x8E7C6E68
604901: 16:41:13.333 Aug 21: ISAKMP: (2073): error suppression node 284724149 FALSE reason 'informational (en) State 1.
604902: 16:41:13.333 Aug 21: ISAKMP: (2073): entry = IKE_MESG_FROM_PEER, IKE_INFO_NOTIFY
604903: 16:41:13.333 Aug 21: ISAKMP: (2073): former State = new State IKE_P1_COMPLETE = IKE_P1_COMPLETE
581504: 16:59:12.805 Aug 20: ISAKMP: (2147): purge the node-1455244451
581505: 16:59:12.805 Aug 20: ISAKMP: (2147): purge the node 840814618
581506: 16:59:13.933 Aug 20: ISAKMP (2147): received 201.195.231.162 packet dport 4500 sport 37897 Global (R) QM_IDLE
581507: 16:59:13.933 Aug 20: ISAKMP: node set 801982813 to QM_IDLE
581508: 20 August 16:59:13.933: ISAKMP: (2147): HASH payload processing. Message ID = 801982813
581509: 16:59:13.933 Aug 20: ISAKMP: receives the payload type 18
581510: 16:59:13.933 Aug 20: ISAKMP: (2147): treatment remove with load useful reason
581511: 16:59:13.933 Aug 20: ISAKMP: (2147): remove the doi = 0
581512: 16:59:13.933 Aug 20: ISAKMP: (2147): remove Protocol id = 1
581513: 16:59:13.933 Aug 20: ISAKMP: (2147): remove spi_size = 16
581514: 16:59:13.933 Aug 20: ISAKMP: (2147): remove the spis num = 1
581515: 16:59:13.933 Aug 20: ISAKMP: (2147): delete_reason = 2
581516: 20 August 16:59:13.933: ISAKMP: (2147): load DELETE_WITH_REASON, processing of message ID = 801982813, reason: DELETE_BY_USER_COMMAND
581517: 16:59:13.933 Aug 20: ISAKMP: (2147): peer does not paranoid KeepAlive.
581518: 16:59:13.933 Aug 20: ISAKMP: (2147): peer does not paranoid KeepAlive.
581519: 16:59:13.933 Aug 20: ISAKMP: (2147): removal of State of SA reason 'Order BY user' (R) QM_IDLE (post 201.195.231.162)
581520: 16:59:13.933 Aug 20: ISAKMP: (2147): error suppression node 801982813 FALSE reason 'informational (en) State 1.
581521: 16:59:13.933 Aug 20: ISAKMP: node set-878597687 to QM_IDLE
581522: 20 August 16:59:13.937: ISAKMP: (2147): lot of 201.195.231.162 sending peer_port my_port 4500 37897 (R) QM_IDLE
581523: 16:59:13.937 Aug 20: ISAKMP: (2147): sending a packet IPv4 IKE.
581524: 16:59:13.937 Aug 20: ISAKMP: (2147): purge the node-878597687
581525: 16:59:13.937 Aug 20: ISAKMP: (2147): entry = IKE_MESG_INTERNAL, IKE_PHASE1_DEL
581526: 16:59:13.937 Aug 20: ISAKMP: (2147): former State = new State IKE_P1_COMPLETE = IKE_DEST_SA
I opened a case with TAC on this and they do not understand what is the cause. For them, it looks like a bug without papers. And their recommendation is to reboot, upgrade or try configuring L2TP for remote users.
Thank you
JP
JP,
An update of IOS is worth it, even if him debugs seems to indicate that there is a problem with the client. If possible, I always suggest test with another client to see if it is unique to the Cisco VPN Client on Win7. Regarding the limit of 20 tunnel, it is very probably the number of IPsec security associations. If you issue a 'show crypto eli', this example displays the number of Sessions that are currently active IPSec.
HTH,
Frank
Tags: Cisco Security
Similar Questions
-
Hello
I set up a lab for RA VPN with a version of the ASA5510 8.2 and VPN Client 5 software using digital certificates with Microsoft CA on a Windows 2003 server. I did the configuration based on this document from Cisco's Web site:
Now, the vpn works fine, but now I need to configure a tunnel-different groups so I can provide different services to different users. The problem I have now is that I don't know how to set it up for the certificate is the name of tunnel-group. If I do an ASA debug crypto isakmp I get this error message:
% ASA-713906 7: IP = 165.98.139.12, trying to find the group through OR...
% 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
% ASA-713906 7: IP = 165.98.139.12, trying to find the group via IKE ID...
% 3 ASA-713020: IP = 165.98.139.12, no group found by matching well payload ID: unknown
% ASA-713906 7: IP = 165.98.139.12, trying to find the group via IP ADDR...
% ASA-713906 7: IP = 165.98.139.12, trying to find the group using default group...
% ASA-713906 7: IP = 165.98.139.12, connection landed on tunnel_group DefaultRAGroupSo, basically, when using certificates I connect always VPN RA only with the group default DefaultRAGroup. Do I have to use a model of different web registration for application for a certificate instead of the user model? How can I determine the OU on the user certificate so that match tunnel-group?
Please help me!
Kind regards
Fernando Aguirre
You can use the group certificate mapping feature to map to a specific group.
This is the configuration for your reference guide:
http://www.Cisco.com/en/us/partner/docs/security/ASA/asa82/configuration/guide/IKE.html#wp1053978
And here is the command for "map of crypto ca certificate": reference
http://www.Cisco.com/en/us/docs/security/ASA/asa80/command/reference/C5.html#wp2186685
Hope that helps.
-
Windows IPSEC and SSL VPN client on the same machine
Matches (coexistence) installation of IPSEC and SSL vpn clients that are supported on the same computer, windows (XP and Win7)?
As mentioned by Patricia and Jennifer (5 stars), you can install two clients on the same machine without any problem.
The tricky part comes when you are trying to connect two clients at the same time, that's when you may encounter unexpected problems.
However, if your intention is to install both clients and connect them individually and not at the same time, you'll be fine.
If you have any other questions, please mark this question as answered and note all messages that you have found useful.
Thank you.
Portu.
Post edited by: Javier Portuguez
-
Problems connecting to help connect any and the Ipsec VPN Client
I have problems connecting with the VPN client connect no matter what. I can connect with the Ipsec VPN client in Windows 7 32 bit.
Here is my latest config running.
Thank you for taking the time to read this.
passwd encrypted W/KqlBn3sSTvaD0T
no names
name 192.168.1.117 kylewooddesk kyle description
!
interface Vlan1
nameif inside
security-level 100
IP 192.168.1.1 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
IP address dhcp setroute
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
boot system Disk0: / asa822 - k8.bin
passive FTP mode
DNS lookup field inside
DNS domain-lookup outside
DNS server-group DefaultDNS
domain wood.local
permit same-security-traffic intra-interface
object-group service rdp tcp
access rdp Description
EQ port 3389 object
outside_access_in list extended access permit tcp any interface outside eq 3389
outside_access_in list extended access permit tcp any interface outside eq 8080
outside_access_in list extended access permit tcp any interface outside eq 3334
outside_access_in to access extended list ip 192.168.5.0 allow 255.255.255.240 192.168.1.0 255.255.255.0
woodgroup_splitTunnelAcl list standard access allowed host 192.168.1.117
inside_nat0_outbound to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240
outside_access_in_1 list extended access permit tcp any host 192.168.1.117 eq 3389
woodgroup_splitTunnelAcl_1 list standard access allowed 192.168.1.0 255.255.255.0
inside_nat0_outbound_1 to access ip 192.168.1.0 scope list allow 255.255.255.0 192.168.5.0 255.255.255.240
inside_nat0_outbound_1 to access extended list ip 192.168.5.0 allow 255.255.255.240 all
inside_test list extended access permit icmp any host 192.168.1.117
no pager
Enable logging
timestamp of the record
asdm of logging of information
Debugging trace record
Within 1500 MTU
Outside 1500 MTU
mask pool local Kyle 192.168.5.1 - 192.168.5.10 IP 255.255.255.0
IP local pool vpnpool 192.168.1.220 - 192.168.1.230
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 631.bin
don't allow no asdm history
ARP timeout 14400
Global (inside) 1 interface
Global 1 interface (outside)
NAT (inside) 0-list of access inside_nat0_outbound_1
NAT (inside) 1 0.0.0.0 0.0.0.0
public static interface 3389 (indoor, outdoor) 192.168.1.117 tcp 3389 netmask 255.255.255.255 dns
public static tcp (indoor, outdoor) interface 8080 192.168.1.117 8080 netmask 255.255.255.255
public static tcp (indoor, outdoor) interface 3334 192.168.1.86 3334 netmask 255.255.255.255
static (inside, upside down) 75.65.238.40 192.168.1.117 netmask 255.255.255.255
Access-group outside_access_in in interface outside
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
WebVPN
the files enable exploration
activate the entry in the file
enable http proxy
Enable URL-entry
SVC request no svc default
AAA authentication http LOCAL console
Enable http server
http 192.168.1.0 255.255.255.0 inside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs Group1 set
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
outside_map card crypto 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
outside_map interface card crypto outside
crypto isakmp identity address
crypto ISAKMP allow outside
crypto ISAKMP policy 10
preshared authentication
3des encryption
sha hash
Group 2
life 86400
Telnet 192.168.1.0 255.255.255.0 inside
Telnet timeout 5
SSH timeout 5
Console timeout 0
dhcpd dns 8.8.8.8 8.8.4.4
dhcpd lease 3000
!
dhcpd address 192.168.1.100 - 192.168.1.130 inside
dhcpd allow inside
!
a basic threat threat detection
host of statistical threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
allow outside
SVC disk0:/anyconnect-win-2.4.1012-k9.pkg 1 image
enable SVC
internal sslwood group policy
attributes of the strategy of group sslwood
VPN-tunnel-Protocol svc webvpn
WebVPN
list of URLS no
internal group woodgroup strategy
woodgroup group policy attributes
value of server DNS 8.8.8.8 8.8.4.4
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
value of Split-tunnel-network-list woodgroup_splitTunnelAcl_1
mrkylewood encrypted Q4339wmn1ourxj9X privilege 15 password username
username mrkylewood attributes
VPN-group-policy sslwood
VPN - connections 3
VPN-tunnel-Protocol svc webvpn
value of group-lock sslwood
WebVPN
SVC request no webvpn default
tunnel-group woodgroup type remote access
tunnel-group woodgroup General attributes
address pool Kyle
Group Policy - by default-woodgroup
tunnel-group woodgroup ipsec-attributes
pre-shared key *.
type tunnel-group sslwood remote access
tunnel-group sslwood General-attributes
address pool Kyle
authentication-server-group (inside) LOCAL
authentication-server-group (outside LOCAL)
Group Policy - by default-sslwood
!
class-map inspection_default
match default-inspection-traffic
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
class inspection_default
inspect the preset_dns_map dns
inspect the ftp
inspect h323 h225
inspect the h323 ras
inspect the netbios
inspect the rsh
inspect the rtsp
inspect the skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect the tftp
inspect the sip
inspect xdmcp
Review the ip options
type of policy-card inspect dns MY_DNS_INSPECT_MAP
parameters
!
global service-policy global_policy
context of prompt hostname
call-home
Profile of CiscoTAC-1
no active account
http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address
email address of destination [email protected] / * /
http https://tools.cisco.com/its/service/...es/DDCEService destination address
destination-mode http transport
Subscribe to alert-group diagnosis
Subscribe to alert-group environment
Subscribe to alert-group monthly periodic inventory
monthly periodicals to subscribe to alert-group configuration
daily periodic subscribe to alert-group telemetry
Cryptochecksum:6fa8db79bcf695080cbdc1159b409360
: end
asawood (config) #.
You also need to add the following:
WebVPN
tunnel-group-list activate
output
tunnel-group sslwood webvpn-attributes
activation of the Group sslwood alias
Let us know if it works.
-
Cisco and Checkpoint VPN clients on a single PC
Hello
I'm in the following fix:
I had used customer Checkpoint SecuRemote 4.1 SP - 5 VPN in the past.
Now, I have installed the Cisco VPN client version 4.0.4 on my PC to access IPSec VPN for the PIX in our headquarters.
According to Cisco VPN release notes http://www.cisco.com/univercd/cc/td/doc/product/vpn/client/rel404/404clnt.htm#wp1346340 , it should be possible to have clients both Cisco and Checkpoint VPN installed on the same machine.
But I am not able to connect to my PIX, I receive the following error message:
"Secure the complete VPN connection locally by the Client.
Reason 403: failed to contact the security gateway. »
When I'm looking for signs of PC control-> system-> hardware-> device Administration-> network cards, I can see Cisco Systems VPN Adapter disabled.
After you activate manually, I always get the same error when you try to connect to the Cisco VPN client.
After PC restart the Cisco VPN adapter is disabled later.
I tried to uncheck Check Point SecuRemote form my Dial-up connection (bypassing CSCea31192 of bug, but the bug does not affect NAT - T connection which I use).
I noticed the same situation on three different computers, one running Windows XP, both running Windows 2000.
After uninstalling the client Checkpoint completely (including Windows registry manual removal), the Cisco VPN client works very well.
It seems to me, therefore, that there is a profound mismatch between Cisco and Checkpoint VPN clients.
Does anyone know of a workaround?
Thank you
Milan
We had the same problem with some of our users who need to use the two clients to connect to customer sites.
If I remember the cisco client does not start automatically, but the client of checkpoint 4.1 don't.
We by-passed by deleting the registry entry point control that starts the client at startup. fwenc.exe is the entrance and it is in
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Run
After that make a shortcut to the executable file that is stored in the directory \bin to relevant checkpoint on the client (it is different from NT & 9 client x) and then only start when it is necessary.
Hope that's a help
-
IP address of the IPSec VPN client did not get distributed via EIGRP
We use an ASA for VPN remote access. He is running EIGRP redistribute static routes. When a client Anyconnect SSL connects, the SAA creates a static route for this client, and it gets redistributed via EIGRP. When an IPSec VPN client connects, the SAA creates a static route for this customer, but he isn't redisributed via EIGRP and so the client can not achieve anything. Why he would distribute a static created by an IPSec client?
Thank you
Have you set up IPP on dynamic Cryptography?
-
Function of automatic update for the IPsec VPN Client
Hello.
Do you have anyone ever tried the PIX / ASA ' feature IPsec VPN Client Auto-Update?
(see also Document ID: 105606).
He wants to make sure that I understand this right.
The user will receive a popup of information telling him to download the latest version of the client? And then there start the update itself?
If so, this would mean that the user must have the rights of full adminsitative using a laptop.
From my point of view, full administrator rights on a laptop are prohibited - 100% and therefore the functionality would be totally useless.
Anyone who can tell me whether I am good or bad?
Best
Frank
Frank,
You are right, if the computer desktop or labtop is completely locked regarding the installation of the software the customer won't be able to install it, they may be able to download from the link that you configured in ASA, once they connect to your server ASA RA but with regard to the installation user's machine needs rights profile appropriate to be able to install it.
HTH
-Jorge
-
AAA ipsec vpn clients how to see the history of connection on asdm or asa5510
Hello all, I would like to know how see history of connection ipsec vpn client users, they authenticate to the local aaa, not in active directory. I am able to see the current logon session. go to monitoring\vpn\vpn statistics\sessions, this shows me sessions underway, but I would like to see for example the connections client vpn for the last month. I did some research and saw the info on aaa Server? I checked that article and does not see what I was looking for.
It's actually a called (NPS) network policy server microsoft radius server.
The one I used (ACS 5 and ACS 5) who was just an example.
You can review the below listed doc
http://fixingitpro.com/2009/09/08/using-Windows-Server-2008-as-a-RADIUS-server-for-a-Cisco-ASA/
Jatin kone
-Does the rate of useful messages-
-
IPsec VPN Client - aggressive mode
Hi all
I just got got off the phone with the customer who underwent a check sweep of security from a third-party vendor. One of the vulnerebilities mentioned in the report is this:
I know that only the IPsec VPN client using aggressive mode to negotiate Phase I. So my question is how to convince my customer to continue to use the IPsec VPN? Is this what can I do to reduce the risk of the use of this type of access remotely. In addition, am I saw the same problem, if I use SSL based VPN Client?
Kind regards
Marty
Hello
Ikev1 HUB in aggressive mode sends his PSK hash in the second package as well as its public DH value.
It is indeed a weakness of slope Protocol.
To be able to act on this, U will be on the path to capture this stream in order to the brute force of the hash [which is not obvious - but not impossible.
This issue is seriously attenuated by activating XAUTH [authentication].
Xauth happens after the DH, so under encryption.
Assuming that the strong password policy is in use, it is so very very very difficult to find the right combination of username/password.
Ikev2 is much safer in this respect and this is the right way.
See you soon,.
Olivier
-
How do I allow IPSec VPN client-to-client
Can someone briefly describe the steps on an ASA to allow both IPSec VPN clients talking to each other. They are in the same pool of addresses. I already have two same-security-traffic permit for inter and intra interface statements. Thank you!
Sent by Cisco Support technique iPhone App
try to including this traffic in the States of sheep you have
Alos, you may need to make changes to the acl split rules
-
RV180 and Cisco IPSec VPN client
Hi NetPro,
RV180 router supports VPN client using the regular Cisco VPN client connections?
Data sheet says it works with client QuickVPN. If the regular non-Quick client is not supported, both clients can coexist (= be installed simultaneously) on the same PC?
Is supported customer QuickVPN split tunneling?
Thank you!
Lubomir
Lubomir Hello,
The RV180 currently supports QuickVPN and PPTP VPN connections. It also has the IPSec tunnel as well, but it does not support the Cisco VPN client.
I saw a question have Cisco VPN and the QuickVPN installed on the same computer.
The QuickVPN client supports only split tunneling.
I hope that answers your questions.
-
Have problems with the IPSec VPN Client and several target networks
I use an ASA 5520 8.2 (4) running.
My goal is to get a VPN client to access more than one network within the network, for example, I need VPN client IPSec and power establish tcp connections on servers to 192.168.210.x and 10.21.9.x and 10.21.3.x
I think I'm close to having this resolved, but seems to have a routing problem. Which I think is relevant include:
Net1: 192.168.210.0/32
NET2: 10.21.0.0/16
NET2 has several subnets defined VIRTUAL local network:
DeviceManagement (vlan91): 10.21.9.0/32
Servers (vlan31): 10.21.3.0/32
# See the road
Code: C - connected, S - static, RIP, M - mobile - IGRP, R - I, B - BGP
D - EIGRP, OSPF, IA - external EIGRP, O - EX - OSPF inter zone
N1 - type external OSPF NSSA 1, N2 - type external OSPF NSSA 2
E1 - OSPF external type 1, E2 - external OSPF of type 2, E - EGP
i - IS - L1 - IS - IS level 1, L2 - IS - IS IS level 2, AI - IS inter zone
* - candidate by default, U - static route by user, o - ODR
P periodical downloaded static route
Gateway of last resort is x.x.x.x network 0.0.0.0
C 192.168.210.0 255.255.255.0 is directly connected to the inside
C 216.185.85.92 255.255.255.252 is directly connected to the outside of the
C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement
C 10.21.3.0 255.255.255.0 is directly connected, servers
S * 0.0.0.0 0.0.0.0 [1/0] via x.x.x.x, outdoor
I can communicate freely between all networks from the inside.
interface GigabitEthernet0/0
Description * INTERNAL NETWORK *.
Speed 1000
full duplex
nameif inside
security-level 100
IP 192.168.210.1 255.255.255.0
OSPF hello-interval 2
OSPF dead-interval 7
!
interface Redundant1.31
VLAN 31
nameif servers
security-level 100
IP 10.21.3.1 255.255.255.0
!
interface Redundant1.91
VLAN 91
nameif DeviceManagement
security-level 100
IP 10.21.9.1 255.255.255.0
permit same-security-traffic inter-interface
NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0
IP local pool vpnpool 172.31.255.1 - 172.31.255.254 mask 255.255.255.0
Overall 101 (external) interface
NAT (inside) 0-list of access NO_NAT
NAT (inside) 101 192.168.210.0 255.255.255.0
NAT (servers) 101 10.21.3.0 255.255.255.0
NAT (DeviceManagement) 101 10.21.9.0 255.255.255.0
static (inside, DeviceManagement) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (inside, servers) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (servers, upside down) 10.21.3.0 10.21.3.0 netmask 255.255.255.0
static (DeviceManagement, upside down) 10.21.9.0 10.21.9.0 netmask 255.255.255.0
access list IN LAN extended permitted tcp 192.168.210.0 255.255.255.0 any
access list IN LAN extended permit udp 192.168.210.0 255.255.255.0 any
LAN-IN scope ip 192.168.210.0 access list allow 255.255.255.0 any
LAN-IN extended access list allow icmp 192.168.210.0 255.255.255.0 any
access list IN LAN extended permitted tcp 10.21.0.0 255.255.0.0 any
access list IN LAN extended permitted udp 10.21.0.0 255.255.0.0 any
LAN-IN scope 10.21.0.0 ip access list allow 255.255.0.0 any
LAN-IN extended access list allow icmp 10.21.0.0 255.255.0.0 any
standard access list permits 192.168.210.0 SPLIT-TUNNEL 255.255.255.0
standard access list permits 10.21.0.0 SPLIT-TUNNEL 255.255.0.0
group-access LAN-IN in the interface inside
internal VPNUSERS group policy
attributes of the VPNUSERS group policy
value of server DNS 216.185.64.6
Protocol-tunnel-VPN IPSec
Split-tunnel-policy tunnelspecified
Split-tunnel-network-list value of SPLIT TUNNEL
field default value internal - Network.com
type VPNUSERS tunnel-group remote access
tunnel-group VPNUSERS General attributes
address vpnpool pool
strategy-group-by default VPNUSERS
tunnel-group VPNUSERS ipsec-attributes
pre-shared key *.
When a user establishes a VPN connection, their local routing tables have routes through the tunnel to the 10.21.0.0/16 and the 192.168.210.0/32.
They are only able to communicate with the network 192.168.210.0/32, however.
I tried to add the following, but it does not help:
router ospf 1000
router ID - 192.168.210.1
Network 10.21.0.0 255.255.0.0 area 1
network 192.168.210.0 255.255.255.252 area 0
area 1
Can anyone help me please with this problem? There could be a bunch of superfluous things here, and if you could show me, too, I'd be very happy. If you need more information on the config, I'll be happy to provide.
Hello Kenneth,
Based on the appliance's routing table, I can see the following
C 10.21.9.0 255.255.255.0 is directly connected, DeviceManagement
C 10.21.3.0 255.255.255.0 is directly connected, servers
C 192.168.210.0 255.255.255.0 is directly connected to the inside
And you try to connect to the 3 of them.
Politics of Split tunnel is very good, the VPN configuration is fine
The problem is here
NO_NAT list of allowed ip extended access all 172.31.255.0 255.255.255.0
NAT (inside) 0-list of access NO_NAT
Dude, you point to just inside interface and 2 other subnets are on the device management interface and the interface of servers... That is the question
Now how to solve
NO_NAT ip 192.168.210.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0
no access list NO_NAT extended permits all ip 172.31.255.0 255.255.255.0
NO_NAT_SERVERS ip 10.21.3.0 access list allow 255.255.255.0 172.31.255.0 255.255.255.0
NAT (SERVERS) 0 ACCESS-LIST NO_NAT_SERVERS
Permit access-list no.-NAT_DEVICEMANAGMENT ip 10.21.9.0 255.255.255.0 172.31.255.0 255.255.255.0
NAT (deviceManagment) 0-no.-NAT_DEVICEMANAGMENT access list
Any other questions... Sure... Be sure to note all my answers.
Julio
-
Remote IPSec VPN - client Windows 7 and ASA 5505
Hello
I'm having trouble with configuring IPSec VPN with Cisco ASA 5505 and Windows 7 client native VPN remotely. My client PC Gets the VPN IP pool address and can access a remote network behind ASA, but then I lose my internet connection. I read that this should be a problem with the split tunneling, but I did as it says here and no luck.
Windows VPN Client settings, if I uncheck "use default gateway on remote network" I have an internet connection (given that the customer is using a local gateway), but then I can't ping remote network.
In the log, I see the warnings of this type:
TCP connection of disassembly 256 for outside:192.168.150.1/49562 to outside:213.199.181.90/80 duration 0: 00:00 0 stream bytes is a loopback (cisco)
I have attached my configuration file (without configuring split tunneling, I tried). If you need additional newspapers, I'll send them right away.
Thank you for your help.
Petar Koraca
That's what you would have needed on versions 8.3 and earlier versions:
permit same-security-traffic intra-interface
Global 1 interface (outside)
NAT (outside) 1 192.168.150.0 255.255.255.0
However I see that you are running 8.4 so I think that all you need is this (I never did on 8.4 so it may not be accurate)
permit same-security-traffic intra-interface
network of the NETWORK_OBJ_192.168.150.0_24 object
dynamic NAT interface (outdoors, outdoor)
Give it a shot and let me know how it goes.
-
Need urgent help in the configuration of the Client VPN IPSec Site with crossed on Cisco ASA5510 - 8.2 (1).
Here is the presentation:
There are two leased lines for Internet access - a route 1.1.1.1 and 2.2.2.2, the latter being the default Standard, old East for backup.
I was able to configure the Client VPN IPSec Site
(1) with access to the outside so that the internal network (172.16.0.0/24) behind the asa
(2) with Split tunnel with simultaneous assess internal LAN and Internet on the outside.
But I was not able to make the tradiotional model Hairpinng to work in this scenario.
I followed every possible suggestions made on this subject in many topics of Discussion but still no luck. Can someone help me here please?
Here is the race-Conf with Normal Client to Site IPSec VPN configured with no access boarding:
LIMITATION: Cannot boot into any other image ios for unavoidable reasons, must use 8.2 (1)
race-conf - Site VPN Customer normal work without internet access/split tunnel
:
ASA Version 8.2 (1)
!
ciscoasa hostname
domain cisco.campus.com
enable the encrypted password xxxxxxxxxxxxxx
XXXXXXXXXXXXXX encrypted passwd
names of
!
interface GigabitEthernet0/0
nameif outside internet1
security-level 0
IP 1.1.1.1 255.255.255.240
!
interface GigabitEthernet0/1
nameif outside internet2
security-level 0
IP address 2.2.2.2 255.255.255.224
!
interface GigabitEthernet0/2
nameif dmz interface
security-level 0
IP 10.0.1.1 255.255.255.0
!
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
IP 172.16.0.1 255.255.0.0
!
interface Management0/0
nameif CSC-MGMT
security-level 100
the IP 10.0.0.4 address 255.255.255.0
!
boot system Disk0: / asa821 - k8.bin
boot system Disk0: / asa843 - k8.bin
passive FTP mode
DNS server-group DefaultDNS
domain cisco.campus.com
permit same-security-traffic inter-interface
permit same-security-traffic intra-interface
object-group network cmps-lan
the object-group CSC - ip network
object-group network www-Interior
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
port udp-object-group service
object-group service ftp
object-group service ftp - data
object-group network csc1-ip
object-group service all-tcp-udp
access list INTERNET1-IN extended permit ip host 1.2.2.2 2.2.2.3
access-list extended SCC-OUT permit ip host 10.0.0.5 everything
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq www
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any https eq
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq ssh
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 no matter what eq ftp
list of access CAMPUS-LAN extended permitted udp 172.16.0.0 255.255.0.0 no matter what eq field
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq smtp
list of access CAMPUS-LAN extended permitted tcp 172.16.0.0 255.255.0.0 any eq pop3
access CAMPUS-wide LAN ip allowed list a whole
access-list CSC - acl note scan web and mail traffic
access-list CSC - acl extended permit tcp any any eq smtp
access-list CSC - acl extended permit tcp any any eq pop3
access-list CSC - acl note scan web and mail traffic
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 993
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq imap4
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq 465
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq www
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq https
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq smtp
access-list extended INTERNET2-IN permit tcp any host 1.1.1.2 eq pop3
access-list extended INTERNET2-IN permit ip any host 1.1.1.2
access-list sheep extended ip 172.16.0.0 allow 255.255.0.0 172.16.0.0 255.255.0.0
access list DNS-inspect extended permit tcp any any eq field
access list DNS-inspect extended permit udp any any eq field
access-list extended capin permit ip host 172.16.1.234 all
access-list extended capin permit ip host 172.16.1.52 all
access-list extended capin permit ip any host 172.16.1.52
Capin list extended access permit ip host 172.16.0.82 172.16.0.61
Capin list extended access permit ip host 172.16.0.61 172.16.0.82
access-list extended capout permit ip host 2.2.2.2 everything
access-list extended capout permit ip any host 2.2.2.2
Access campus-lan_nat0_outbound extended ip 172.16.0.0 list allow 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
Enable logging
debug logging in buffered memory
asdm of logging of information
Internet1-outside of MTU 1500
Internet2-outside of MTU 1500
interface-dmz MTU 1500
Campus-lan of MTU 1500
MTU 1500 CSC-MGMT
IP local pool 192.168.150.2 - 192.168.150.250 mask 255.255.255.0 vpnpool1
IP check path reverse interface internet2-outside
IP check path reverse interface interface-dmz
IP check path opposite campus-lan interface
IP check path reverse interface CSC-MGMT
no failover
ICMP unreachable rate-limit 1 burst-size 1
ASDM image disk0: / asdm - 621.bin
don't allow no asdm history
ARP timeout 14400
interface of global (internet1-outside) 1
interface of global (internet2-outside) 1
NAT (campus-lan) 0-campus-lan_nat0_outbound access list
NAT (campus-lan) 1 0.0.0.0 0.0.0.0
NAT (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT, internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
Access-group INTERNET2-IN interface internet1-outside
group-access INTERNET1-IN interface internet2-outside
group-access CAMPUS-LAN in campus-lan interface
CSC-OUT access-group in SCC-MGMT interface
Internet2-outside route 0.0.0.0 0.0.0.0 2.2.2.5 1
Route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
Timeout xlate 03:00
Timeout conn 01:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
Sunrpc timeout 0:10:00 h323 0:05:00 h225 mgcp from 01:00 0:05:00 mgcp-pat 0:05:00
Sip timeout 0:30:00 sip_media 0:02:00 prompt Protocol sip-0: 03:00 sip - disconnect 0:02:00
Timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-registration DfltAccessPolicy
the ssh LOCAL console AAA authentication
AAA authentication enable LOCAL console
Enable http server
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
HTTP 1.2.2.2 255.255.255.255 internet2-outside
HTTP 1.2.2.2 255.255.255.255 internet1-outside
No snmp server location
No snmp Server contact
Server enable SNMP traps snmp authentication linkup, linkdown cold start
Crypto ipsec transform-set esp-SHA-ESP-3DES-3des esp-sha-hmac
Crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
Crypto ipsec transform-set ESP-DES-SHA esp - esp-sha-hmac
Crypto ipsec transform-set ESP-DES-MD5 esp - esp-md5-hmac
Crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
Crypto ipsec transform-set ESP-3DES-MD5-esp-3des esp-md5-hmac
Crypto ipsec transform-set ESP-AES-256-SHA 256 - aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-SHA aes - esp esp-sha-hmac
Crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
Crypto ipsec transform-set ESP-AES-128-MD5-esp - aes esp-md5-hmac
life crypto ipsec security association seconds 28800
Crypto ipsec kilobytes of life - safety 4608000 association
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 pfs set group5
Crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 value transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA MD5-ESP-3DES ESP-DES-SHA ESP-DES-MD5
Crypto map internet2-outside_map 65535-isakmp dynamic ipsec SYSTEM_DEFAULT_CRYPTO_MAP
crypto internet2-outside_map outside internet2 network interface card
Crypto ca trustpoint _SmartCallHome_ServerCA
Configure CRL
Crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
a67a897as a67a897as a67a897as a67a897as a67a897as
quit smoking
ISAKMP crypto enable internet2-outside
crypto ISAKMP policy 10
preshared authentication
aes encryption
md5 hash
Group 2
life 86400
Telnet 10.0.0.2 255.255.255.255 CSC-MGMT
Telnet 10.0.0.8 255.255.255.255 CSC-MGMT
Telnet timeout 5
SSH 1.2.3.3 255.255.255.240 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet1-outside
SSH 1.2.2.2 255.255.255.255 internet2-outside
SSH timeout 5
Console timeout 0
a basic threat threat detection
Statistics-list of access threat detection
no statistical threat detection tcp-interception
WebVPN
internal VPN_TG_1 group policy
VPN_TG_1 group policy attributes
Protocol-tunnel-VPN IPSec
username ssochelpdesk encrypted password privilege 15 xxxxxxxxxxxxxx
privilege of encrypted password username administrator 15 xxxxxxxxxxxxxx
username vpnuser1 encrypted password privilege 0 xxxxxxxxxxxxxx
username vpnuser1 attributes
VPN-group-policy VPN_TG_1
type tunnel-group VPN_TG_1 remote access
attributes global-tunnel-group VPN_TG_1
address vpnpool1 pool
Group Policy - by default-VPN_TG_1
IPSec-attributes tunnel-group VPN_TG_1
pre-shared-key *.
!
class-map cmap-DNS
matches the access list DNS-inspect
CCS-class class-map
corresponds to the CSC - acl access list
!
!
type of policy-card inspect dns preset_dns_map
parameters
message-length maximum 512
Policy-map global_policy
CCS category
CSC help
cmap-DNS class
inspect the preset_dns_map dns
!
global service-policy global_policy
context of prompt hostname
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Adding dynamic NAT for 192.168.150.0/24 on the external interface works, or works the sysopt connection permit VPN
Please tell what to do here, to pin all of the traffic Internet from VPN Clients.
That is, that I need clients connected via VPN tunnel, when connected to the internet, should have their addresses IP NAT'ted against the address of outside internet2 network 2.2.2.2 interface, as it happens for the customers of Campus (172.16.0.0/16)
I am well aware of all involved in here, so please be elaborative in your answers. Please let me know if you need more information about this configuration to respond to my request.
Thank you & best regards
MAXS
Hello
If possible, I'd like to see that a TCP connection attempt (e.g. http://www.google.com) in the ASDM logging of the VPN Client when you set up the dynamic NAT for the VPN Pool also.
I'll try also the command "packet - trace" on the SAA, while the VPN Client is connected to the ASA.
The command format is
packet-tracer intput tcp
That should tell what the SAA for this kind of package entering its "input" interface
Still can not see something wrong with the configuration (other than the statement of "nat" missing Dynamics PAT)
-Jouni
-
SafeNet and Cisco VPN Client Compatible?
I have been using the Cisco VPN for quite awhile with no problems. Recently, we have added a Watchguard Firebox somewhere else and have installed the Client of Watchguard MUVPN, otherwise known as a customer of Safenet.
Since the installation, I could not yet properly use the Cisco Client. If I disable the two Services of Safenet, I invited to my user id and password and connect to the Cisco Concentrator and get an ip, etc. However, I can't ping anything on the network.
My solution is to completely uninstall both clients and reinstall the Cisco by itself. This is not very practical.
If anyone know a fix for this I'd appreciate comments.
Thank you
Patrick Dunnigan
Hi Patrick,
I only got lucky with the SafeNet customer brand Watchguard with the 4.0.x releases of the Cisco client. I think Cisco 4.6 clients use a newer driver from the DNE or else that plays well with SafeNet.
In any case, here's how to set up PC that requires both clients:
First, install the Cisco VPN client. Restart the application, and then stop and disable the Windows service.
Install the client for Watchguard, reboot as requested.
Then, stop and set to manual both SafeNet services, then start and set to automatic the Cisco service.
Delete the shortcut in your Start menu Startup group safecfg.exe (or the key of HKLM\MS\Windows\CurrentVer\Run, where he gets set.)
Delete the shortcut to start for the Cisco VPN client as well.
Whenever you want to use the Cisco customer, you can just launch the Dialer to IPSec. If you want to run the SafeNet client, stop the Cisco service, start the services of SafeNet, then run safecfg.exe. A few batch files facilitate this process for users.
Hope that helps,
Chris
Maybe you are looking for
-
Hello Logic Pro Does anyone know why music should continue to play after I deleted all parts of this region in all tracks?
-
Windows Media Player - loss of sound
My sound suddenly stopped during playback of a CD through Windows Media Player, as I lost the sound when you open an attachment through Windows Media Player. What should I try?
-
The backup computer fails with the error "access is denied. (0x80070005) »
original title: computer backup failure My computer will be back up to a point, then will be an error "access is denied. (0x80070005) "at the same time, Microsoft security essentials SAIS it detects a potential threat. My question is this: if he stop
-
Dell v715w - cannot retrieve the application list from your computer
I have a new desktop WIN7 64 bit Voastro (replaced a dimension on XP) I can't use the printer control panel to scan. I get is unable to retrieve the list of applications on your computer on the screen of the printer. Have reinstalled the printer at
-
Fonts in PDF reports displays does not correctly
Hi people,One of our clients have the problem TH (Thai) new sarabun font is not displayed correctly.Our production environment has no problem.Info:Oracle Application Server 10g 10.1.2.0.2OS: Windows Server 2003 SP11 fonts are added to REPORTS_PATH an