Ukraine power... VI

Similar Questions

• Multiple Ukraine power measurement

  Hello

  I use the card Ni SMU 4143. I have a VI that propels a certain voltage level card.  Now, I'm trying to create a separate VI which will only measure the voltage and current on the power supply without a reset provision. I understand that I must "log on" to the device before I use the "power measurement multiple.vi Ukraine", but whenever I use the session initiate, it will my device and set my level of back tension reset. Can you please explain how I can create a VI that measures only the voltage and current without changing their level?

  After the opening, why don't call you the VI that determines the level? Not this separate VI also call the lance function? Think that the flow of data.

• Measurement time 4132 SMU is too high

  Hello

  I use PXI - 4132 DC EMS to perform some DC measurements at high speed. I just took a 1 K Ohms resistance, forced 1mA and measure 1V. I have this done configuration and code completed. I get the correct measurements. But my problem is with the measurement time. The total duration is about 45ms to complete installation and measurement, with the exception of the 'initialize and close '.

  I checked the time at every step and I noticed that the maximum duration is taken during the "voltage reading. Out of the total 45ms, it takes about 34ms just for a measure. It's just a VI "Ukraine power measure" takes about 34ms, which is ridiculous compared to the Kiethleys. I tried to vary the time of "openness" and turn off the 'Auto Zero'. But the measurement time is still high. Can someone help me and let me know what is the best time of the measurement obtained with 413 x series SME?

  Thank you!

  Hey Phx_tech,

  The amount you reduce your delay source depends very much your HAD and how regular you have to your level of tension until you start taking your measurements.  If your Instrument is reactive, you can see discount gas and unintentional ringing during the transition from your output level and therefore would allow enough break-in before taking your measurement. The best thing to do is to experiment with different delays of source and see how much delay need you to get a consistent and reproducible measure. If you have a scope that is available, it will also show you the step response of the SMU with your Instrument.  If your first reading is higher than your other readings, that this could very well be a problem with not enough time settling.  What kind of DUT Testez_ you?

  From page 4 of the specification, you can see that 1 PLC, we can expect about 1 ppm RMS noise of the range to 1 PLC. This means in the range 10 au our measurement noise would be 10 pA RMS or 60 pA pk - pk.  However, your DUT + cables will pick up the extra noise and you should consider using wires of twisted shield pair to reduce noise picked up in your system.  The shield can be terminated at the mass of the chassis on the side EMS of the cable to help reduce noise appearing in your measurement.

  

  Let us know what you find after experimenting with you HAD.

  Thank you!

  Brandon G

• Try to connect to the power supply via the IP address

  Hello

  I am trying to connect to a power supply of Sorensen XEL60 - 1.5 P. I have its IP address and port number, but I'm stuck on an error 63, cited at the end I tried the advice in this forum and online without success, including:

  Disabling firewall

  * the ip address ping command

  * Tools > options > VI Server

  http://digital.NI.com/public.nsf/allkb/6ccced1045c479d286256a3a00655123

  Open all the ports LV wants

  Nothing improves the situation. What I will try?

  Thank you very much

  

  Error 63:

  LabVIEW: Serial Port receive buffer overflow.
  =========================
  LabVIEW: The network connection was refused by the server. For TCP/IP, make sure that the server is running and listening on the port you want to use. Firewalls can also cause a server to refuse a connection. To VI Server, make sure that you have enabled the server from VI tools > Options > VI Server.

  No reason to be a donkey to people asking for advice. I tried UKRAINE by the boards, conscientiously the profit and loss account.

  I can actually get the power supply to operate on the VISA. It needed fixed two bugs, in the case where others are interested:

  * Setting VI_ATTR-TERMCHAR_EN to VI_TRUE

  * Creation of the resource VISA under the 'manual entry of the raw socket"rather than one of the other two. This is necessary because I'm trying to communicate via a specified port.

  So I'm fine now, I just can't pass strings directly via IP and port that I thought I should. It may be a device-specific problem, but I'm always interested in other thoughts.

  Thank you

  Warren Harding

• My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  My iPhone 6 installed 10.0.2 stops when it gets to 40% of autonomy.  In addition, it seems to pass power WAY to fast with the new software.  Does anyone else have this problem?

  Hello brooksm549,
  Thank you for using communities of Apple Support.

  I got your message which, since updating your iPhone 6 to iOS 10.0.2 your iPhone stops when it is 40% and the power to empty very quickly. I understand your concern with the iPhone turn off and drains the battery. I recommend you to review the use of the battery to see what app contributes more to the battery drain. The following article will provide you with steps on how to check the use of the battery:

  On the use of the battery on your iPhone, iPad and iPod touch

  When you know about the soft uses more battery, you can change your settings in order to optimize the battery life:

  Maximize the life of the battery and battery life

  Best regards.

• [Power Mac G5] Type of liquid cooling system?

  Y at - it anyway how to determine type of LCS just by looking at the case?

  We have old school Power Mac G5 DP 2, 7GHz (early 2005) we use for editing (well, for the last two years, he's right there and no one wants to touch this old piece of...). They will throw him in the year, and since I was take care of him for a while, I thought I'd take home when they do and use it as a backup machine for the data of my and my wife. I would like the max memory, put a few large hard drives (and small SSD, but there seems to be a lot of problems with this) and run the Linux command (more problems).

  But first, I have to clean the machine and look at the State of it. What particularly concerns me is the LCS (DP 2, 7GHz I) - these things have been prone to leaks and what I found there are at least three revisions of the LCS - second of them made by Panasonic seems to be the most reliable. I can't look inside, deeply, because it must be ready to use at least for another 3-4 months, I can do is to open the case and remove the front fan and look outside the heater.

  So this brings me to my question: Y at - it anyway to determine the type of LCS just by looking at the case?

  Thank you...

  Apparently, there were two models more prone to leaks than others, although still very rare. See this http://www.everymac.com/systems/apple/powermac_g5/faq/powermac-g5-liquid-cooling-infos-fuites-issues.html

  The damage inflicted by a system of flight are very serious, and it is almost impossible to hide or completely clean. As soon as you open the side panel on the Power Mac, you will easily be able to tell if this unit experianced a problem.

• Exceptional activities related to power

  After that 5-6 years my MacBook battery needs service, classified as a replacement of the battery, but until I get my new battery... Please help me this is my only machine for everything I do. Recently, I see unusual activity on my MacBook, which associated powers and may be the charger cable, for example today when I connect the charger, the led light with a delay also after a few movements on cable!

  When LED on, after a few minutes, 35% collected on the status, LED changed to green and status of load emissions MacBook: 37% charged battery, then return to the normal load State!

  It is only linked to the battery mode or should I concerned about port and MagSafe charger cable? I have fixed my cable charger broken 7-8 months ago and it has worked very well.

  Thank you

  Kind regards

  Hey there alpha120,

  I understand that you are experiencing some problems with the power of your MacBook. While it looks like a spare battery is a good option for this behavior, you can also try a SMC reset:
  

  Reset the management system (SCM) controller on your Mac - Apple Support

  Thank you for coming to Apple Support communities, let us know if we can be of further assistance.

  See you soon.

• Activate App stuck on waiting and power Mode low does ' t

  Hi all

  I have at least two concurrent problems with my iPhone 6 + iOS 10.0.2 (but started with iOS 9).

  I can't install new application directly from the App Store on the phone because they were stuck in the phase of "pending". Same behavior of update of the applications that are already installed.

  The only way to update/install the app's iTunes download and synchronize.

  The other simultaneous problem is in what regards the activation of "low power mode" with the rocker switch (settings > farm > Low Power). Whenever I try to activate (manual or automatic 20% of battery) function, the gray toggle becoming in the Middle, then return to the OFF position.

  I already have backupped & restored several times, but nothing has changed.

  How can I solve this?

  Thank your

  Best regards

  Hello Axoduss,

  Thanks for posting in the communities of Support from Apple. I see that you have two problems. One is that the low power Mode is not activated, and the other is that updates and new applications are blocked pending. I know that I rely on my iPhone for everything. It is important to ensure that it works as expected. I'll be more than happy to help.

  Great job to the backup of your phone and restore. It's a great way to help solve these issues.

  If you are restoring from a backup, the problem may be in the back upward. I recommend to reset the phone to factory settings and set up like new to see if the Mode low power and installing apps works. If this does not work after the installation in the new and not after the restoration then you want to restore your data manually and not market back. Here is an article on setting up the phone as new:

  Use iTunes on your Mac or PC to restore your iPhone, iPad or iPod settings - Apple Support

  Let us know if that helps.

  Take care!

• I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I have problems to restart of Yosemite, after power failure during the new backup, and now HD is also blocked.

  I tried the holding of 'command-r' and 'option' to see if the problem can be resolved or try any boot from a boot disk, my old backup, USB function start - but after a slow long process it all just stops.

  There is software on my HD that I don't want to lose by simply reformatting the computer, because I am now in a different country, far from my house, which is another problem of the Apple Store, to reinstall my OS from Yosemite on the www.

  Hey AmnonMikeCohen,

  Thank you for being a part of the communities of Apple Support.

  I understand that your Mac is not start properly after the power went out.  Let's start with resetting the SMC and NVRAM on your Mac and see if he can start from there:

  Reset the management system (SCM) controller on your Mac.

  How to reset the NVRAM on your Mac.

  See you soon.

• Power point

  Is there an outlet, especially for iMac computers or do you have to buy a Microsoft Power Point program which is compatible?

  Yes, there is a PowerPoint for Mac available from Microsoft.

• There's the iPhone battery chargers 5 that use no electricity.  For use in a power failure.

  There's the iPhone battery chargers 5 that use no electricity.  For use during a power failure.

  Your best bet is an accumulator.  I have one I got on Amazon by EC Tech.  It is a brick, but it will charge my iPhone and the iPad, if the current is cut off.  You just need to load the brick and keep it in an emergency.

• Watch OS shows 3 past mode of power with almost total of battery reserve

  Hello world

  I have a problem since I updated my watch to watch OS 3. Watch (series 1) goes into unexpected battery power with an almost total reserve mode. It produces one or two times a day and the only thing that I recognize that the watch remains black when I look at my wrist. It shows only the time in green numbers when I press a button and I need to reboot by pressing the two buttons. After the reboot, the watch displays + 80 or even 90 + % battery life and it works as expected for the rest of the day (if is not the same problem from happening again). Especially my battery is 50 + % at the end of the day.

  Today I reset the watch and recovered from backup, but that changed nothing. The watch went to the mode of power with a range of 78% a few minutes ago

  I am really frustrated because it happens very often and I could not find a solution to this problem. Decommissioning watch OS 2 is not an option...

  Thanks in advance for your help, I am really stuck on this issue.

  Best regards from Germany,

  Matthias

  Hi, Matthias

  If your dial of the Watch includes the complication of the battery, it is possible that accidental screen interactions are causing your issue.

  Tapping on the complication battery indicates the level of battery with a large button to put the watch mode of power reserve.

  You can consider using your watch for a while without this complication on the face of the watch to see if the issue is recurring:

  Change the face of the watch on your Apple Watch - Apple Support

• iPad power Switcj

  On my iPad, the power as well as the blow of unlocking button do not work. How can I solve this problem?

  Take it to Apple for a free estimate, or call them and arrange for express service. It cannot resolve hardware problems yourself. You will need to get a replacement from Apple. Apple does not repair the individual components like that, they replace the whole device with a service unit. If you are in warranty and parts failures were due to a manufacturing defect, it would be free. If out of warranty or if the failures were due to accidental damage or misuse, the elimination of guarantee fees apply.

  iPad repair - official Apple Support

• Power cord for my iMac has crunched, how do I get a new one?

  What I do my power cord for my iMac has been chewed and I don't know if I can claim the title of the guarantee or if I should just buy a new...

  As I can use it only if I put in some way and cannot be pulled.

  If the plug of your end iMac has this form:

  

  Then the power cord to any standard computer work.  It may not be

  White enough with the beautiful fitting molded but it will work.

• no available power source battery

  

  my battery in the form x lounge, I connect to the power supply cord

  but the power supply continues to display battery

  

  already reset smc, just update macos what to do next? Thanks for help

  You can choose to wait until your computer is open to the public

  and diagnostic tests performed, if this issue does not affect

  any software update or upgrade; because the device must be

  provided with a steady current while the software is installed. In particular

  with the Mac App Store and if you use a wi - fi connection to access the internet.

  Usually the SMC or system management controller, if reset in one

  effectively, should also be a reset of power management,

  If the process is not successful, there may be other problems in

  the charging circuit which will have an impact on the whole Mac.

  https://www.Google.com/search?q=magsafe + dc-in + Council + alternative + MacBookAir +

  One of the elements which can manifest a strange behavior is whether or

  When the "MagSafe DC-in Board" has become defective. It can

  show no battery and always run the Mac. It may also fail totally in

  a way without notice; that can't end well if use it right now.

  • Make an appointment at an Apple Retail Store Genius Bar
  • Find an Apple authorized service provider

  Visit a regular on an Apple store with genius, or an authorized

  Apple's Service provider is recommended; to get a practice notice

  and certain diagnoses. They also estimate repair costs.

  • Laptops Apple: Troubleshooting MagSafe adapters - Apple Support

  • About batteries for laptops Mac - Apple Support

  Are the points of contact in the clean and free MagSafe connectors

  debris? -Which can cause the partial connection or errors here.

  Hard to say most likely probable cause of this problem. Maybe the material.

  Check out the details between the bandages. Recommend: technical diagnosis.

  Good luck in this case!